Home

Controller

1. PTZ ID 17 to 32 DVR input 1 16 SA In DVR mode when DVR2 is selected and input channel is switched to No 2 the keyboard will automatically set the current camera to ID 18 which is physically connect to the 2nd input of the DVR DVR ID Monitor ID for output SET DVR ID 01 OUT 0001 gt SET CHANNEL dus CAM 0001 DVR ch ID Ge ID mapped to DVR CH ID SET CAM PROTOCOL Setup the Protocol for CAM Each camera can be program with different Protocol After setting press ENTER to save or CLR to exit the setting SET CAM PROTOCOL ALL gt PELCO D gt SET PROTOCOL 0001 gt PELCO D ALL Protocol setting for all CAMERA ID 01 individual setting for CAMERA ID 01 SET CAM BAUDRATE Set up the Baud rate for CAM Supported settings 1200bps 2400bps 4800bps 9600bps and 19200 bps After setting press ENTER to save or CLR to exit the setting SET CAM PROTOCOL ALL 9600bps gt SET_BAUDRATE gt 0001 gt 9600bps ALL Protocol setting for all CAMERA ID 01 individual setting for CAMERA ID 01 SET KEY ID Set up the ID of the controller from O1 to 63 Input the No by digit key After setting press ENTER to save or CLR to exit the setting SET KEY ID gt 01 lt 01 63 SET KEY LEVEL Set up the control levels of the controller from 00 to 15 Input the No by digit key After setting press ENTER to save or CLR
2. Preset function Add Preset SET n ENTER n 1 to 255 Call a preset SHOT n ENTER n 1 to 255 Delete a preset CLR n ENTER n 1 to 255 The maximum preset number depends on the PTZ device Please refer to the user s manual for further information SET n SHOT n 001 0001 0001 001 0001 0001 Tour Sequence A sequence can store up to 24 preset points with individual dwell time and speed You can store a sequence by using this function only availiable in B01 BO2 Protocol Press GRP n SET n 1 to 4 After entering sequence programming mode the display shows the preset input and setting for speed and time Seq Pos Spd Ti Seq Sequence number Pos Preset number 001 000 000 000 Spd Move speed between 1 8 Ti Stop time between 0 60 sec Press ENTER to confirm and save the setting Repeat the preset pos input with speed and time setting and confirm with enter After exiting the programming mode the settings will be saved to dome s memory Enter DVR mode Function key for NVIDO DVR LED f To control DVR press the DVR Button and enter the Ih T DVR ME Function Key DVR mode The LED with DVR tag indicates t
3. 12
4. 01 ne Input 1 of the MUX PTZ Cam 0001 prz Control PTZ Cam 0001 ID of the Camera Press N Enter to change the channel Setup the virtual PTZ control in MUX mode MUX ID 01 In MUX mode press AUTOPAN to change mi the selected Multiplexer Set MUX ID 2 Select the MUX ID if many installed for 01 00 66 gt setup ID of MUX Monitor ID for output OUT 0001 Press AUTOPAN again to setup the PTZ admin access required press ENTER is otherwise the configuration may be lost MUX CH ID Camera ID 11 IN 01 CAM 0001 after every assignment to save the changes RS 485 Termination Devices using RS485 control are usually connected in daisy chain which reqiuers termination with 120Q resistor on both ends Following picture illustrates the connection methods please note that a daisy chain connection type shall not exceed 7 meters RS485 RS 485 Distributor i Mum RS 485 esistor Device 1 Device 2 Device 3 Star Connection The star form connection is mostly used it enables the connection of different dome cameras in longer distance Itis recommended to use RS485 distributor to ensure the telemetric data transmission 1 RS485 Rs485 Distributor Video Distributor
5. to exit the setting SET KEY LEVEL 201 00 15 gt SET MON RANGE Set up the range of monitors from 0000 to 0239 Input the No by digit key After setting press ENTER to save or CLR to exit the setting SET MON RANGE 20000 0239 SET CAM RANGE Set up the range of intelligent dome cameras from 0000 to 9999 Input the No by digit key After setting press ENTER to save or CLR to exit the setting SET CAM RANGE gt 0000 9999 SET ALM RANGE Set up the range of alarm positions from 0000 to 9999 Input the No by digit key After setting press ENTER to save or CLR to exit the setting SET ALM RANGE gt 0000 9999 RESET DEFAUL_I Set the keyboard setting to factory default default password is 0123456789 Press ENTER to reset or CLR to exit This process can take up to 30 sec till the controller is available again Note that after Baud Rate changing its is necessary to restart the keyboard RESET DEFAULT I RESET DEFAULT 1 kkkkkkkkkk PLEASE WAIT 7 Start PTZ mode By default the keyboard usually starts in PTZ mode display shows as below You can also press MENU to change to PTZ mode MON CAM ALM PTZ Mode 001 0001 0001 Select Change current camera You can change the camera by pressing CAM n ENTER N represents the channel number which should be selected CAM n 001 0001 0001 Change selected camera
6. 3 Axis Multi functional Programmable Controller User s Manual WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit FCC COMPLIANCE STATEMENT FCC INFORMATION THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FORA CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGHEND TO PROVIDE REASONABLE PROTECTION AGAINST HAMRFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENGERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE CAUTION C
7. HANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS S AUTHORITY TO OPERATE THE EQUIPMENT CE COMPLIANCE STATEMENT WARNING THIS ISACLASS APRODUCT INADOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES This Symbol indicates that this product should not be treated as household waste When discarding this product it must be sent to appropriate facilities for recycling or recovery By separating this product from other household waste you are helping to reduce the volume of waste incinerators and the natural resource will be conserved CAUTION BEFORE ATTEMPTING TO CONECT OR OPERATE THIS PRODUCT PLEASE READ THE LABEL ON THE BOTTOM AND USER S MANUAL CAREFULLY CONTENTS Nui c E 1 PEES EN 2 T Sx quod sec 2 J Men secre ingoio re res 2 O Seu eenden denn enen tid eran 3 ar Keyboard SED aaneen nar eere ced d add Ra EO RR 5 z Woking with T Es prada stemtest 6 x Working WIND VE eeens toreni sanke 9 Working with MultiplgXer eorr rrt aeree 11 0 CONNECCION M 12 Technical specification are subjects to change without prior notice This Manual may contain printing or clerical errors All trademarks mentioned belong to their respective owners 1 PRECAUTION Refer all work related to the installaion of this product to qualified service personnel or syst
8. System Keyboard MON CAM ALM 001 0001 0001 Keyboard Sounds After power on keyboard will start the initialization and self test The LC Display will show initial screen Press Menu to start the operation ENGLISH Operation Screen MON Selected Monitor CAM Selected Camera ALM Selected Alarm input The keyboard provides acustic signal when a button is pressed Depends on application it can be activated or deactivated 1 Turn ON the Keyboard Sounds Press ON 1 at the same time 2 Turn OFF the Keyboard Sounds Press OFF 1 at the same time User Mode amp Admin Mode The keyboard will enter automatically into USER MODE after power up which allows performing PTZ and DVR control and restrict user access to keyboard setup menu Following message will show ADMIN AUTHORITY 001 0001 0001 Enter Administrator Mode PASSWORD kkkkkkkkkk 1 Press ON 2 at the same time 2 enter your password with the number key and confirm with ENTER The Default Password is 9876543210 After entering the Administrator mode press MENU to enter the setup menu In order to get all advantages and functions it is strongly recommended to setup your keyboard before operation Navigation Return to the previous level ev change the value or options CLR by turning the control s
9. em installers Do notattemp to disassemble the appliance To prevent electric shock do not remove screws or cover There are no user serviceable parts inside Contact qualified service personnel for maintenance Handle the appliance with Care Do not strike or shake as this may damage the appliance It should be protected against extreme pressure vibration and humidity during transportation and storage Damages caused by improper transportation avoid the warranty Do not operate the apliance beyond its specified temperature humidity or power source ratings Do not use the keyboard in an extreme environment where high temperature or high humidity exists Use it within 5 C to 40 C 23 F to 140 F and a humidity below 90 The input power source is 9V 12V DC and requires at least 500mA Read this user s manual carefully before operating the appliance Make sure that local electric safty standard are followed when using or installing the appliance Do not install this Product in a flammable and explosive environment Make sure that the installation is done according to your local electricity and safety regulation Before installation and mentainence make sure that the appliance is disconnected from the power source Do notuse any power source other than 12V DC in order to prevent damages to this device For details please refer to the section Specifications for further details Handle the device during the instal
10. es i RS485 rH j 12V DC edF Power input on J RS 232T NS To Keyboard 12V DC Power supply dada RS232 Serial GND Y RXD Interface 2 GND TXD Key Description o LCD Display o with back light 5 3 Operation O O O O Bin se Keys Camera Extended Operation Keys Function Keys Digit pad 3 Axis Joystick Camera Operation Keys Zoom WIDE TELE Zoom in and out FOCUS FAR NEAR Manual focus IRIS OPEN CLOSE Manual irisl Operation Keys DVR Enter the DVR control mode MUX Multiplexer mode Digit pad 0 9 Digit input from 0 to 9 Key MON Monitor switch CAM Camera switch CLR Clear amp Cancel ENTER Enter key MENU Enter setup menu or PTZ mode 3 Axis PTZ Joystick SET Set preset position SHOT Recall preset position Extended Function Keys ALM Alarm Function GRP Tour function OFF Function Off ON Function on AUTOPAN Auto pan function AUX Auxiliary function RUN Function Start HOLD Hold PREV Previous device NEXT Next device LEFT RIGHT Pan movement UP DOWN Tilt movement TURN Zoom in Out t UP LEFT O gt TELE RieHT zoom A i DOWN i WIDE Vxx lt 01 gt
11. he 65555 8i EDU Sol current status and the LC Display shows the current tno aie A 2u selected DVR ID GOES Enter Key Enter Oooo e LJ 4 Cut Hold DVR ID 01 C 9 Cut Prev Press Button to enter DVR mode 16 Cut IRIS close Zoom Wide Tele Key If you have more than 1 DVR installed and configured you can switch to other ID by pressing NEXT n ENTER For returning to PTZ mode press MENU Slow playback Aux i Start Recording ALM Depends on the DVR Model the function keys might be different please refer to later ON chapter for key assignment Playback Key Pause Autopan Virtual PTZ control in DVR mode Key Stop IRIS Open l Key Rewind GRP In this mode you can control the DVR and PTZ simultaneously by selecting the input on the DVR the PTZ ID assigned to this channel will be automatically selected Key Forward OFF and ready for PTZ control DVR and PTZ ID assignment need to be set prior to Keyboard Infomation Run operation Please refer to the former chapter Keyboard Setup for details Power ON OFF DVR x Press DVR key in DVR mode to enter virtual PTZ Ch Display 1N N 0 9 1 N Enter Ch Display ON N 1 9 0 N Enter DVR D 01 ID of the DVR Key Plus 3D Joystick Right DVR ID 01 IN 01 INO irn Input 1 of the DVR Key Mi 3D Jovstick Left PTZ Cam 0001 PTZ eccirni Indicates the virtual PTZ mode ey MINUS SYSUOS Ce Cam 0001 Camera or PTZ ID Key Audio Focus Near Key Search Focus Far Switch the camera input chan
12. lation carfully Falls or extreme vibration may cause irrepairable damages and avoid the warranty Do not install or operate the appliance near any high voltage devices or high voltage cable The safety distance should remain atleast 50 m This product should be operated indoor only 2 FEATURES This keyboard is a multi funcational programable keyboard controller for Pan Tilt Zoom device Digital Video Recorder and Matrix devices and can be programmed with individu protocol setting for each connected device It is equipped with a 3 Axis joystick for performing Pan Tilt and Zoom action with single hand Main Features Manage up to 9999 devices controls PTZ DVR and Matrix in different protocol with pre programmed setting 3 Axis joystick Multiplexer operation with DVR and PTZ Password protected for administrative access Supports major telemetric protocols Dual serial interface with RS232 and RS485 Supports major DVR brand variable PTZ Speed Aluminium finishing Ergonomic Design 3 PACKING LIST Please unpack the equipment and make sure all listed items and accessories are included in the box Controller Connection 1 x 4 Pin RS232 Clip AC DC Power 1x User Manual Box 1 x 2 Pin RS485 Clip Supply 1 x Keyboard Cable Optional 4 CONNECTION RS485 Serial Description PTZ or Interface DVR RS 232R 4 RS485 RS485 v
13. nel Press N ENTER For returning to the DVR mode press again the DVR key Key Next DVRID S tting Clear Keyboard screen CLR Change the PTZ assignment in DVR mode Keylock SHOT If you are already in Admin mode you can change the assignment of the PTZ ID to Key Left Joystick Left the DVR input directy by pressing NEXT key Key Right Joystick Right Key Up Joystick Up Set DVR ID Select the DVR you need to control or Key Down Joystick Down 01 lt 00 99 gt modity DVR ID output to matrix ID 01 OUT 0001 Press again NEXT to Change the assignment for DVR input and Note IN 01 CAM 0001 camera ID admin access required please setup the communication baud rate and ID in the DVR correctly before connection Assign to To prevent signal interference it is strongly recommended to use RS 485 distributor for DVR Input Channel Camera ID connection Control Multiplexer in MUX mode I LED for Press the MUX button to enter the Multiplexer mode LJ _ MUX Mode dee Bt 10 Dou o0 HAH L1 A MUX ID 01 Ee Press Button to g enter MUX mode PTZ with Multiplexer in MUX mode In MUX mode press the button MUX again to enter virtual PTZ mode You can control the PTZ by switching the input channel the camera ID will also be switched accordingly r z MUX ID 01 ID of the MUX MUK TORO wet IN
14. tick to the LEFT or RIGHT end ENTER Confirmation or save setting 2 Scroll the main menu Digit input for changing lt gt Navigate the cursor between 0 9 function value the sub items n Move UP DOWN LEFT or RIGHT MENU Back to Menu SET MUX PROTOCOL Setup the Protocol for Multiplexer Supporting ROBOT VC SONY BOSCH and PELCO SET MUX PROTOCOL gt ROBOT SET MTX BAUD RAT Set up the Baud rat for Matrix Supporting 1200bps 2400bps 4800bps 9600bps and 19200 bps Press ENTER to save or CLR to exit SET MTX BAUD RAT gt 9600bps SET DVR PROTOCOL Setup the DVR Protocol Supported NVIDO VC DSCP HIK TUMIN MITSU DH and INTLX SET DVR ALL NVIDO gt SET PROTOCOL 01 gt NVIDO ALL Protocol setting for all DVR ID 01 individual setting for DVR ID 01 SET DVR BAUTRATE Setup the baud rate for DVR Supported 1200bps 2400bps 4800bps 9600bps and 19200 bps SET DVR ALL gt 9600bps gt SET_BAUDRATE gt 0001 gt 9600bps ALL Baud rate setting for all DVR ID 01 individual setting for DVR ID 01 J SET DVR CHANNEL When multiple DVRs are used the keyboard can map the DVR channel input to a certain PTZ s ID Once the DVR s channel is changed the PTZ which responding to this channel will be selected automatically DVR 1 5 PTZ ID 1 to 16 DVR input 1 16 Example DVR2

Controller

Contents

Download Pdf Manuals

Related Search

Related Contents