Manual - Orbital Tracker
Contents
1. 5 6x3 2x1 4 inches Weight 0 4Kq a VERV IMPORTANT PLEASE READ BEFORE USE The Battery must be connected before use The terminal wires have been unplugged for transportation Remove back cover and manually connect the battery cables to the satellite meter The battery must be charged for 4 5 Hours before using the meter for the first time Failure to do this will affect the batteries performance Your Latitude and Longitude will be required for satellite meter setup please go to the website bellow for your Latitude and Longitude www findlatitudeandlongitude com Do not expose to dispose of the batterv in fire Avoid shorting the batterv Avoid excessive phvsical shock or vibration Do not disassemble or deform the battery Do not leave battery in charger over 10 hours Store the battery in a cool dry and well ventilated area Keep battery packs away from children Promptly and properly dispose of used battery packs according to local regulations for the disposal of batteries Damaged or leaking battery packs should be handled with extreme care Charge unused battery packs at least once every six months Charge the battery packs only with the specified charger Never use a modified or damaged charger Do not charge battery packs near combustible or conductive materials Charge the battery packs in a well ventilated room that does not exceed room temperatures of 400C 1040F Cleaning and Maintenance Do not e2. da DIGITAL SATELLITE METER TRACKER LIGHT OTM 500 Manual WWWURBITALI RALKER LUM TRAGKER LIGHT Preset Global Satellite Data Bank 0 User Defined Satellite Data Bank Wide Clear Easy to Read LCD All Parameters show on one screen Easy to Learn Easy Operation Keypad Editing Switchable Back Light o Internal Power Supply Can be powered from the satellite receiver Universal Charger 120vac 6OHz 220vac 50 Hz 12vdc Car Charger True USB interface Replaceable F 81 connectors 9 Ruff Neck protective jacket Cost Effective Input frequency 950 2150 MHz Signal field range 30dBuV 105dBuV Accuracy 1 5dB Input Impedance 75 Ohm F connectors Output impedance 75 Ohm F connector Display Code segment wide temperature LCD Measuring method Signal strength bit error rate S N Pitch tone on audio speaker QPSK switch Automatic identification 22K control Supported Audio output Built in Speaker Memory content 300 reserved locations for global satellite channels 100 user defined channels LNB Power Supply 13V 18V lt 500mA Interface mode USB Adapter power AC100V 240V DC input DC13 5V 1A Output port voltage DC12 23V Battery time 374 hours continuously after full charge varying from LNB with different power consumption Charging time 3 6 hours Working Temp 0 C 40 C Storage Temp 10 C 50 C Exterior size 142x82x35 mm
3. can save 100 user defined satellite parameters vou can also save frequently used parameters here Using and key select the channel The meter has preset the data of most satellite channel plans in the world and reserves 300 empty channel plans Inputting the longitude and latitude of your location the meter will automatically select and display a channel that you can receive 4 Latitude and longitude settings amp functions zone LONG Longitude LAT Latitude SAVE It blinks when pressing to indicate saved successfully Indicates the mode of local channel plan Hold HH for 3 seconds until the symbol shows indicating the speaker is off Press and hold for 3 seconds again to turn on the speaker Linked with PC j Shows current battery status LI blinks when the battery is low 5 Measurement zone After setting satellite parameters you should move cursor to channel number zone and press any numeric key from 0 to 9 to activate the measurement S Signal Q Quality column S Q column displays the signal strength and signal quality in percentage S S N and B Values S Actual value of signal strength S N Carrier noise ratio B Bit error rate Indicates the satellite signal has been locked The Locked icon will show only on satellites that have a ID Frequency In general if the S and Q are showing strong values you are on the satellite frequency selected Try to maximize the S and Q Bars to obtain
4. of a satellite s receiver can supply power to the satellite meter when the battery is low or battery is removed Connect the receiver s input port to the satellite meters output port See Fig 1 Power supplied by recatver Const with LNB After Charging your Meter for 4 6 Hours turn ON meter Hold the power kev until the meter beeps and enters the main menu 1 Enter the coordinates of vour location Latitude and Longitude You can get your Lat and Long by going to website below The Lat and Long does not have to be exact it is used to determine the satellites you can capture from your City State or Region www findlatitudeandlongitude com 1 1 Enter the latitude and longitude of your location Option First using key move cursor to channel number zone Make sure the measurement zone is blank otherwise press any numeric key to quit the measurement mode Then hold 0 key for 3 seconds the cursor will move to the longitude and latitude setting zone As shown in Fig Below Cfplonc ME LAT 39N For example Enter Longitude 117E Latitude 39N aq Pa a Using key move cursor to LONG using or Lfi key select the number digit and enter the number 117 when the cursor blinks Continuing to press or LH key until E East or W West blinks press any key from 0 to 9 to shift between E and W Using key move cursor to LAT enter 39 Continuing to pres
5. the best satellite signal T 6 faa val ba lii as TRACKER 11 IL 12 14 13 Input port The port to connect with LNB Satellite Dish LNB Output port When the battery is low connect this port with input port of satellite receiver then turn on the receiver to supply power for meter and get signal input LCD LCD display with backlight Option Key amp shift key between default and user defined channel plans Single press the cursor will move downwards circularly Hold for 3 seconds screen will shift between default and user defined channel plans Number digit key amp backlight key Single press cursor moves left Hold for 3 seconds to turn on or turn off backlight Number digit key amp mute key Single press cursor moves right Hold for 3 seconds to turn on off the speaker Save amp delete key Press to save modified items Hold for 3 seconds to delete the selected item Load and unit key Single press load parameters in local channel plan to user defined a 6 10 CL 12 13 14 channel plan Hold for 3 seconds to shift among the measurement unit s dBuV dBmV dBm Numeric Keys Enter numbers from 0 to 9 When cursor is in channel number zone press any numeric key to start or stop the signal measurement Hold 0 key for 3 seconds to enter local longitude amp latitude modifying mode POWER ON OFF ON Off Light USB Port Power Input Speaker The input port
6. ber and press any numeric key to start testing 1 7 Copy a channel from default channel plan to the user channel plan na ano BE In default channel plan mode using and keys select the favorite channel and press LdElkev The meter displays SAM in the lower right and the channel is copied to the user channel plan ok 1 8 Modify channels in both default amp user channel plan In the default or user channel plan mode using the key move the cursor to the item to modify it Press key to save The meter displays SAVE in the lower right and the channel modification is saved successfully In the default channel plan mode the L item can t be modified Above function can t be done in the test mode press any numeric to switch out of test mode 1 9 Delete channel in the user channel plan In the user channel plan mode using LS and keys select the channel to be deleted and hold for 3 seconds to delete the channel 1 10 Restore factory settings Type in 9876 immediately after power on about 5 seconds later the meter will restart and recover to factory settings All saved and modified contents will be lost Please use this function very carefully G 1 11 Software Upgrades Software upgrades will be available on the www orbitaltracker com website wee ORBI TAL TRACKER DIGITAL SATELLITE METER WWW ORBITALTRAGKER COM D ll
7. input port is connected with LNB the meter will detect LNB noise and display the signal level indicating the LNB is OK and connected well with the meter a 1 4 Signal searching Turn the antenna in the direction the meter indicates the tone will become louder and clearer When the antenna is close to the satellite the meter will shows an increasing value of S Signal and Q Qualitv Bars and Ber Tech Tip Alwavs trv to maximize the signal on the Q Qualitv Bar betore completing vour installation S g U Baw sin 5 8 ap sa B 0E 05 Continue to turn the antenna slowly in the direction that makes the S Q Bars increase When the value is sufficient the meter will sound a steady audio able tone The WAS icon will appear on the display when signal is verified Continue to tune the antenna until the meter shows the maximum S Q bar reading s B 3 Baru s N 10 6 dB 0E 05 SN a CRE LONG ME LAT ol LU Important Note In measurement mode you can scroll different frequencv s by pressing the or LH keys by 1MHz Steps Press key to save 1 5 Using default channel plan t Hold key until amp icon shows at the lower right corner of screen press or to change the channel number Press any numeric key to start testing 1 6 Using user channel plan In default channel plan hold key until icon disappears The meter enters user channel plan mode H Press or to change channel num
8. s or key until N or S blinks press any key from 0 to 9 to shift between N and S Hold 0 for 3 seconds to save and exit A Enter parameters In user channel plan move cursor to channel number zone press Or LA IKev to select an emptv channel Option plan pressing key to move cursor to L F SR LO LNB 22KHz and enter the correct parameters one by one For example Moving cursor to L and enter 146E at blinks using Eor HE Enter number when the digit blinks using or key move the cursor When the cursor is at hundred it wont blink directly enter 1 Continuing to use or L Ikev move the cursor to E or W when E or W blinks press any numeric key from 0 to 9 to shift between E or W When the cursor is at LNB or 22KHz use any numeric key to shift between the options reali LONG Tal After entering all parameters press na key to save The cursor moves to channel number area automatically and all parameters are saved into current channel successfully Note As L is entered the meter will calculate elevation and polarization and display on the positioning guide zone according to local longitude amp latitude you have entered provided the satellite program is available locally 1 3 Signal measurement Make sure the cursor is in the channel number zone press any numeric key to launch signal test mode When the
9. xpose the meter and charger to liquid moisture or humidity it is not waterproof Please clean the meter and charger periodically with soft dry cloth Do not use alcohol thinner or benzene solution to clean them e 1 Tracker Light Satellite Meter e 1 Protective Body Case e 1 AC Battery Charger e 1 DC Auto Charger e 1 USB Cable e 1 Carrying Strap e 2 Removable F Connectors e 1 User Manual The TRACKER LIGHT Digital satellite meter is a professional grade meter designed for satellite installations With its FAST TRACK signal processor and audible tone generator it will make satellite locating and installation a simple process The meter calculates the elevation and polarization automatically and shows in the display according to your location and satellite s longitude The meter comes with a built in Global Satellite channel list you can also download Satellite Parameters via PC or manually edit the user defined Satellite Parameters The Tracker Light can store 100 custom satellite parameters 3 1 Positioning guide zone A Indicates the azimuth direction E Indicates the degree of elevation P Indicates the LNB polarization angle 2 Satellite Settings Zone L Satellite longitude F Transponder frequency SR Symbol rate LO Local oscillator frequency LNB 13V vertical or 18V horizontal polarization switch 22KHz Control ON indicates on blank indicates off 3 Channel number zone User channel plan
Download Pdf Manuals
Related Search