"user manual"
Contents
1. you chose the type of job you can do Pushing on the button you turn back to the previous page Choose of work 4 15 New Job single ply If you push the drawing which represents the single ply fabric it appears this page relative to the Measure of single ply free space HHHH header others H others lt lt Back Next gt gt Note in place of some numbers appear Pushing on numbers a keyboard appears on the monitor with whom you can insert the desired measure the measure indicates how much the support has to move on from an application to the sequent To confirm the inserted measure push press ESC to cancel insertion Measures are expressed in millimeter when you write for example 10 5 the support moves of I centimeter and 5 tenths The measures meaning is explained in the following table free space Support millimeters that you want leave from a waterfall to the following header Moving dimensions in millimeters of the support which is necessary to glue the first fabric at the desired distance others Moving dimension in millimeters of the support which is necessary to glue the following fabrics at the desired distance Pushing on the button you turn back to the page of Choose of job type Pushing on the button you enter in the page of Start working 5 15 New job two ply If you push the drawing which represents the two ply fabric it2. appears this page relative to the measure of two ply free space H header HHHH H header reversa HHHH H others HHHH H others reverz HHHH others HHHH H lt lt Back Next gt gt Note in place of some numbers appear Pushing on numbers a keyboard appears on the monitor with whom you can insert the desired measure the measure indicates how much the support has to move on from an application to the sequent To confirm the inserted measure push press ESC to cancel insertion Measures are expressed in millimeter when you write for example 10 5 the support moves of I centimeter and 5 tenths The measures meaning is explained in the following table free space Support millimeters that you want leave from a waterfall to the following header Moving dimensions in millimeters of the support which is necessary to glue the first fabric at the desired distance Header revers Moving dimensions in millimeters of the support which is necessary to glue the first fabric revers at the desired distance others Moving dimension in millimeters of the support which is necessary to glue the following fabrics at the desired distance Others revers Moving dimension in millimeters of the support which is necessary to glue the following fabrics revers at the desired distance Pushing on the button you turn back to the page of Choose of job type Pushing on the button you
3. User Manual Issue 10 7 02 Versione SW 1 2 1 15 Index SWC D De ence oe ee eee Rene ey Oe ee ee err rere 3 NA A O 4 New Tobi o 5 NEW JOD WO DIY Sa a a 6 Recorded on sele cio a nas oscura 7 O A SO 8 ENN OT KIT A e e PR SOS E RO 10 Delete recorded JOD seriosa AAA 12 SUPPOTU PCCCING aaa iii 13 e e en II a ER rener NS 14 TT OMI IESO AMO nec 15 2 15 Switch on Switching on the machine there appears on the monitor some words which are not necessary to use the machine they can be ignored After some seconds it appears this starting page ILEC AD n alzira Serial t ttt Set up Time je The inscription near to Serial indicates the machine serial number which has to be communicated to the constructor in case of trouble The bar under the inscription Set up time runs till the value 100 at this moment it appears the following page Choose of work eC Hew Job Recorded Job Delete Job On the operator monitor four buttons appear New job see page 4 e Recorded job see page 7 e Delete job see page 12 Feedings see page 13 Note pushing the button directly on the operator monitor it is possible to choose the desired function 3 15 New Job If you choose the button New job it appears the following page of the Choose of job type Press on Job type picture Single lt lt Back Two ply ply Pushing on the drawing of the job type I wo ply or Single ply
4. ancel the erasing process Pushing on the button you turn back to the page of Choose of work 12 15 Support Feeding If in the page Choose of work you push feeding it appears the following page support feeding Feedings To move the tractor use the selector on the rear or the buttons below Unroll support Roll up support lt lt Back At this moment the selector on the rear of the machine is enabled The selector allow to move the tractor cylinder to help you to insert the support in the machine Once you have introduced the support from rear you can move to the front of machine and use the two buttons Unroll Support and roll up support to place the support Pushing on the button you turn back to the page of Choose of work 13 15 Emergency If you pushed the red button EMERGENCY the machine immediately stops and the following page appear EMERGENCY Return to job Stop the Job Pushing the Return to job button you can resume what you were doing before the emergency Pushing the Stop the job button you turn back to the page of Choose of working 14 15 Troubleshooting Problem the support doesn t move Possible causes if the clamp isn t in high position the roll can t move the inverter is not Ready Possible solution check if the sensor placed over the pneumatic pistons are well placed and firmly blocked eventually move the sensor up and down or replace it swit
5. ch off the machine per three minutes check if something block the roll or make 1 hard to move Problem the clamp doesn t move down Possible causes the sensor of heater in high position doesn t work properly This sensor allow the clamp to come down Possible solution the clamp can t move down if the heater is not high check if something fabric or something else blocks the run of the heater check if the sensor over the pistons are well placed and firmly blocked eventually move the sensor or replace it Problem the clamp remains down indefinitely Possible causes the sensor of clamp in low position starts the pressing time counting If the sensor doesn t work properly the pressing time never last Possible solution check if something fabric or something else blocks the run of the clamp check if the sensor over the pistons are well placed and firmly blocked eventually move the sensor or replace it Problem on the control panel question marks appear instead of number water fall type drawing and job name Possible causes the data connection cable between PLC Siemens and control panel is unplugged the PLC Siemens is off the PLC Siemens is broken Possible solution check the cable on both side PLC and control panel and if the plug screw are locked check the fuse F6 replace the PLC with a new one 15 15
6. enter in the page of Start working 6 15 Recorded job selection If in the page Choose of work you push recorded job it appears the following page recorded job selection Recorded job selection Job hh hhhhhh55 E lt lt Back Next gt Note instead of the name of the last used program or some exclamation points appear Pushing on button index book you find the list of the memorized work programs using the buttons you roll by the list of the program names pushing on you confirm the chosen program pushing ESC you cancel your choice If you remember by heart the program name to be used you can push on the symbols and the keyboard appears with which you can insert the desired name pushing on you confirm the program name written ESC you cancel your choice Pushing on the button you turn back to the page of Choose of job type Pushing on the button you enter in the page of Start working 7 15 Start working If you decide to start a new job or you choose a memorized work you push and you will find the following page relative to the start working Working Colors number Waterfall number Temperature HHH Pressing time Sec Joh 144449494444444444 4 EE bag Note in place of some numbers appear instead of the name of the last used program or some exclamation points appear In the table are shown the work parameters Yon can insert Col
7. l back to the previous measure and it permits to repeat the application and positioning cycle The button J permits to avoid gluing a fabric it leaves an empty space on the support simply moving without pushing the support 10 15 The TY button permits to always maintain high the heater for particular working types 1t permits to heat immediately the support PAY ATTENTION Always maintaining the heater high increases the danger of burning hands and fingers To avoid burns use gloves with an adequate thermal protection 11 15 Delete recorded job If in the page Choose of work you push delete job it appears the following page delete recorded job Delete recorded job LE Job HEEE EEEEEEEEEEG al lt lt Back Note instead of the name of the last used program or some exclamation points appear Pushing on button index book you find the list of the memorized work programs using the buttons you roll by the list of the program names pushing on you confirm the chosen program pushing ESC you cancel your choice If you remember by heart the program name to be used you can push on the symbols and the keyboard appears with which you can insert the desired name pushing on you confirm the program name written ESC you cancel your choice Pushing on Wj the program whose name is written near to name is deleted pushing on you confirm the program to be deleted pushing ESC you c
8. oose of work Pushing on the Start button you find the working page and you will begin to work 9 15 Working If you pushed the ert button you arrive at the working page A PEEEEEEEEE SELES S Done Total Temperature HHH FC Pressing time sec Cutting manage Note In place of some number appear instead of the name of the last used program or some exclamation points appear Working sequence 1 Insert a fabric under the clamp 2 Take you hands away but keep the fabric stopped 3 Push the pedal or the green button on the control panel 4 The machine sticks your fabric 1 the heater rises 2 as the heater is high the clamp begins to move down 3 as the clamp is down the fabric is pressed the machine waits for Pressing time seconds 4 then the clamp rises 5 as the clamp is high the heater will move down The support moves to reach the position where you have to stick the next fabric Nn The button No on the side of Cutting manage allow you to enable the cutting of the waterfall as you glue the last color If you press the button it will change in Yes to remind you that the cutting function is enabled Press the button again to disable the cutting manage it will change in No Pushing the button STOP you stop the work The button gj permits to you to repeat the last measure eg if the fabric is the wrong one but only the last one The machine unrol
9. ors number Number of different fabric per waterfall Waterfalls number Numbers of waterfalls to be done Temperature Temperature of malting of the glue over the support must be set up according to the type of glue and support Pressing time Enduring of the pressing time the base time is the tenth of second so inserting 3 3 the fabric will be pressed for 3 second and 3 tenths Job The name of the program we are using Pare Pushing on button index book you find the list of the memorized work programs using the buttons you roll by the list of the program names pushing on you confirm the chosen program pushing ESC you cancel your choice You can for example update a work which has just been used with the one which is in use note if you edit the name you don t select a new program you only write the name of it so the measure remain the same If you want to record the program with the current name you have to push the button W If you want to modify the program name only the name not the measures to be used you can push on so it appears a keyboard with whom you can insert the desired name pushing on you confirm the written name pushing on ESC you cancel your Choice 8 15 Pushing on the va button you can modify the measures coming back to the pages of measure of single ply or measure of two ply according to the type of work you choose Pushing on the button you turn back to the page of Ch
Download Pdf Manuals
Related Search