Leica Builder Quickguide
Contents
1. 7 For orientation method Manual Angle Setting enter bearing and accept with OK 8 Aim at target point and accept with OK Station and Orientation will be set after pressing YES Previous Station and Orientation parameters will be replaced by the new calculated ones 9 For orientation method Known Backsight Point select point from the memory or enter new point or coordinates of known backsight point and accept with OK 10 Aim at target point and accept with OK Station and Orientation will be set after pressing YES Previous Station and Orientation parameters will be replaced by the new calculated ones Step Screen Description 9 Leica Builder Quickguide 4 SETUP Establish Coordinates Anywhere Description The Setup method Establish Coordinates Anywhere is used to set up the instrument on an unknown point and set the orientation by measuring angles and distances to two known target points All further measuring points and points to be staked are in relation to the used coordinate system Diagram Setup method Estab lish Coordinates Anywhere step by step P0 Station P1 First known point P2 Second known point P0 P1 P2 Step Screen Description Make sure that PROG Mode is active 1 Press SETUP 2 Press to highlight Setup option Coordinates and accept with OK 3 Press to highlight Setup option Anywhere and accept with OK 4 Enter instrument height and reflecto2. to calculate a block volume Step Screen Description Total Quality Management Our commitment to total customer satisfaction Leica Geosystems AG Heerbrugg Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems ISO standard 9001 and Environmental Management Systems ISO standard 14001 Ask your local Leica dealer for more information about our TQM program 748969 1 0 0en Original text Printed in Switzerland 2005 Leica Geosystems AG Heerbrugg Switzerland Leica Geosystems AG Heinrich Wild Strasse CH 9435 Heerbrugg Switzerland Phone 41 71 727 31 31 www leica geosystems com
3. Leica Builder Quickguide Version 1 0 English Leica Builder Quickguide 2 In this manual Chapter Page 1 SETUP Establish Control Line Over 1st Point 3 2 SETUP Establish Control Line Anywhere 5 3 SETUP Establish Coordinates Over Known Point 7 4 SETUP Establish Coordinates Anywhere 9 5 SETUP Establish Height 11 6 APPLICATION PROGRAM Layout 13 7 APPLICATION PROGRAM As Built 15 8 APPLICATION PROGRAM Angle amp Distance 17 9 APPLICATION PROGRAM Tie Distance 19 10 APPLICATION PROGRAM Area 21 To use the product in a permitted manner please refer to the detailed safety instructions in the User Manual 3 Leica Builder Quickguide 1 SETUP Establish Control Line Over 1st Point Description The Setup method Control Line Over 1st Point is used to set the station coordinates to E0 0 000 N0 0 000 H0 0 000 and the orientation to 0 000 All further measuring points and points to be staked are in relation to the control line Diagram Setup method Estab lish Control Line Over 1st Point step by step P0 Station P1 Target point P1 P0 Hz 0 000 Step Screen Description Make sure that PROG Mode is active 1 Press SETUP 2 Press to highlight Setup option Control Line and accept with OK 3 Press to highlight Setup option Over 1st Point and accept with OK 4 Aim at target point and accept with OK Station and Orientation will be
4. PROG Mode is active 1 Press APPL 2 Press to highlight application program As Built and accept with OK 3 Aim at target point Press MEASURE for at least 5 seconds to turn on off Laser pointer 4 Measure and record point If a Setup method with Control line was used the values line offset and height are displayed If a Setup method with Coordi nates was used the easting northing and height are displayed The graphic shows the position of the station the reflector and the measured points APPLICATION PROGRAM As Built Leica Builder Quickguide 16 17 Leica Builder Quickguide 8 APPLICATION PROGRAM Angle amp Distance Description The application program Angle amp Distance is used for measuring an unlim ited number of points The program shows horizontal angle horizontal distance and height Diagram Application program Angle amp Distance step by step P0 Known Station P1 Measured point Measued horizontal angle b Horizontal distance P1 P0 b Step Screen Description Make sure that PROG Mode is active 1 Press APPL 2 Press to highlight application program Angle amp Distance and accept with OK 3 Aim at target point Press MEASURE for at least 5 seconds to turn on off Laser pointer 4 Measure and record point The measured horizontal angle horizontal distance and height difference are displayed The graphic shows the position of the station
5. SETUP Establish Control Line Anywhere Leica Builder Quickguide 6 Station and Orientation will be set after pressing YES Previous Station and Orientation parameters will be replaced by the new calculated ones Step Screen Description 7 Leica Builder Quickguide 3 SETUP Establish Coordinates Over Known Point Description The Setup method Establish Coordinates Over Known Point is used to set up the instrument on a known point and orient to a known azimuth or to a known backsight point All further measuring points and points to be staked are in relation to the used coordinate system Diagram Setup method Estab lish Coordinates Over Known Point step by step P0 Known Station P1 Known backsight point Known azimuth P1 P0 Step Screen Description Make sure that PROG Mode is active 1 Press SETUP 2 Press to highlight Setup option Coordinates and accept with OK 3 Press to highlight Setup option Known Point and accept with OK 4 Enter instrument height and reflector height and accept with OK 5 Select point from the memory or enter new point or coordinates of known station point and accept with OK SETUP Establish Coordinates Over Known Point Leica Builder Quickguide 8 6 Press to select orientation method and accept with OK For orientation method Manual Angle Setting continue with step 7 For orientation method Known Backsight Point continue with step 9
6. cation program Layout and accept with OK 3 If a Setup method with Control line was used enter line offset and height values for the point to be staked relative to the control line If a Setup method with Coordi nates was used enter east north and height coordinates of the point to be staked For BUILDER RM press to select points from the memory if available 4 Turn telescope until horizontal angle shows nearly 0 000 APPLICATION PROGRAM Layout Leica Builder Quickguide 14 Press MEASURE for at least 5 seconds to turn on off Tracking Mode If Tracking Mode is acti vated the stake out differences are displayed continuously 5 Press MEASURE to measure point The stake out differences line offset and height are calculated and displayed The graphic shows the position of the prism relative to the point to be staked 6 Move prism until stake out differ ences show nearly 0 000m Step Screen Description 15 Leica Builder Quickguide 7 APPLICATION PROGRAM As Built Description The application program As built is used for measuring an unlimited number of points The program shows line and offset values or easting northing and height depending on the used Setup method Diagram Application program As Built step by step P0 Station P1 Line start point P2 Second line point P3 Measured point d1 Line d2 Offset P2 P1 P0 P3 d1 d2 Step Screen Description Make sure that
7. pt with OK 3 Enter station height instrument height and reflector height and accept with OK If the station height is unknown press HTRANS to access setup method Height Transfer 4 Select known height point from the memory or enter new point or height and accept with OK 5 Aim at height point 6 Measure height point New station height will be set after pressing YES SETUP Establish Height Leica Builder Quickguide 12 Previous station height will be replaced by the new calculated ones Step Screen Description 13 Leica Builder Quickguide 6 APPLICATION PROGRAM Layout Description The application program Layout is used to place markers in the field at prede termined points These predetermined points are the points to be staked The points to be staked are defined by entering line and offset or easting northing and height depending on the used setup method For BUILDER RM the points can also be selected from the memory The program calculates and displays the difference between the measured point and the point to be staked Diagram Application program Layout step by step P0 Station P1 Current position P2 Point to be staked d1 lt gt go forward or lt gt go back d2 lt gt go right or lt gt left d3 lt gt fill or lt gt cut P0 P1 P2 d2 d3 d1 Step Screen Description Make sure that PROG Mode is active 1 Press APPL 2 Press to highlight appli
8. r height and accept with OK 5 Select first point from the memory or enter new point or coordinates and accept with OK 6 Aim at first point 7 Measure and record first point SETUP Establish Coordinates Anywhere Leica Builder Quickguide 10 8 Select second point from the memory or enter new point or coor dinates and accept with OK 9 Aim at second point 10 Measure and record second point Compare the calculated line length and the measured line length 11 If the difference is within the limit accept with YES Station and Orientation will be set after pressing YES Previous Station and Orientation parameters will be replaced by the new calculated ones Step Screen Description 11 Leica Builder Quickguide 5 SETUP Establish Height Description The Setup Option Establish Height is used to enter the station height instru ment height and reflector height If the station height is unknown a Height Transfer can be performed to determine the height of the position of the instrument from a measurement to a target point with known height All further measuring points and points to be staked are in relation to the entered values Diagram Height Transfer Setup method Estab lish Height step by step P0 Station P1 Point with known height P1 P0 Step Screen Description Make sure that PROG Mode is active 1 Press SETUP 2 Press to highlight Setup option Height and acce
9. re and record second point Once two points have been meas ured and recorded the calculated horizontal distance height differ ence grade and slope distance between the measured points are displayed 8 Press OK to measure more points Step Screen Description 21 Leica Builder Quickguide 10 APPLICATION PROGRAM Area Description The application program Area is used to compute online areas from an unlim ited number of points connected by straights The target points have to be measured Additionally a block volume can be calculated Diagram Application program Area step by step P0 Station P1 Start point P2 Target point P3 Target point P4 Target point a Perimeter b Calculated area always closed to the start point P1 P1 a P2 P3 P4 P0 b Step Screen Description Make sure that PROG Mode is active 1 Press APPL 2 Press to highlight application program Area and accept with OK Press MEASURE for at least 5 seconds to turn on off Laser pointer 3 Aim at first point 4 Measure and record first point 5 Aim at second point 6 Measure and record second point 7 Aim at third point 8 Measure and record third point Once three points have been meas ured and recorded the calculated area perimeter and number of points are displayed 9 Press OK to measure more points APPLICATION PROGRAM Area Leica Builder Quickguide 22 10 Or press VOLUME
10. set after pressing YES Previous Station and Orientation parameters will be replaced by the new calculated ones SETUP Establish Control Line Over 1st Point Leica Builder Quickguide 4 5 Leica Builder Quickguide 2 SETUP Establish Control Line Anywhere Description The Setup method Establish Control Line Anywhere is used to set up the instrument along a control line The coordinates of line start point are set to E0 0 000 N0 0 000 and H0 0 000 The orientation is set to 0 000 in the direction of the second line point Additionally line startpoint can be shifted by entering or measuring line and offset values All further measuring points and points to be staked are in relation to the control line Diagram Setup method Estalish Control Line Anywhere step by step The height of line start point is used as the reference height for all further measurements P0 Station P1 Line start point P2 Second line point P3 Shifted line start point a Line value for shift b Offset value for shift P2 P3 b a P1 P0 Hz 0 000 Step Screen Description Make sure that PROG Mode is active 1 Press SETUP 2 Press to highlight Setup option Control Line and accept with OK 3 Press to highlight Setup option Anywhere and accept with OK 4 Aim at line start point 5 Measure and record line start point 6 Aim at second line point 7 Measure and record second line point
11. the reflector and the measured points APPLICATION PROGRAM Angle amp Distance Leica Builder Quickguide 18 19 Leica Builder Quickguide 9 APPLICATION PROGRAM Tie Distance Description The application program Tie Distance is used to compute horizontal distance height difference grade and slope distance between two target points The target points have to be measured The user can choose between two different methods Polygonal P1 P2 P2 P3 Radial P1 P2 P1 P3 Diagram Polygonal P1 P2 P2 P3 Diagram Radial P1 P2 P1 P3 Application program Tie Distance step by step P0 Station P1 Target point P2 Target point P3 Target point d1 Distance between P1 and P2 d2 Distance between P2 and P3 P1 d1 d2 P2 P3 P0 P0 Station P1 Target point P2 Target point P3 Target point P4 Target point d1 Distance between P1 and P2 d2 Distance between P1 and P3 d3 Distance between P1 and P4 P1 d1 d2 d3 P2 P3 P4 P0 Step Screen Description Make sure that PROG Mode is active 1 Press APPL 2 Press to highlight application program Tie Distance and accept with OK APPLICATION PROGRAM Tie Distance Leica Builder Quickguide 20 3 Press to select method and accept with OK Press MEASURE for at least 5 seconds to turn on off Laser pointer 4 Aim at first point 5 Measure and record first point 6 Aim at second point 7 Measu
Download Pdf Manuals
Related Search