Home

AirLive WL-5470AP User Manual

1. Mode Status TCP IP Reboot WS E i WLAN Access Point Acti men WDS Repeater Mode Settings page 15 Used ta Alias Name erent Alias Name Wireless AP Disable Wireless LAN Interface Band 2 4 GHz B G SSID lailive SS Channel Number ha d Wireless Client Isolation Disabled 902 1d Spanning Tree Disabled zl Security setup WDS Security setup Advanced Settings setup Access Control Setup Apply Changes Reset You can set the alias name for this device limited not exceed 32 characters O Disable Wireless Check the box to disable the Wireless LAN Interface by so doing you won t be LAN Interface Channel Number Wireless Client Isolation able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only O 2 4GHz B G 802 11b supported rate and 802 11g supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID It is case sensitive and must not exceed 32 characters A device will not be permitted to join the BSS unless it can provide the unique SSID An SSID is also
2. Air Live www ovislink com tw Powered by OvisLink Corp Declaration of Conformity We Manufacturer Importer OvisLink Corp SF NO 6 Lane 130 Min Chuan Rd Hsin Tien City Taipei County Taiwan Declare that the product Wireless AP WL 5470AP is in conformity with In accordance with 89 336 EEC EMC Directive and 1999 5 EC R amp TTE Directive Clause Description WEN 300 328 V1 6 1 Electromagnetic compatibility and Radio spectrum Matters ERM 2004 11 Wideband transmission equipment operating in the 2 4GHz ISM band And using spread spectrum modulation techniques Part 1 technical Characteristics and test conditions Part2 Harmonized EN covering Essential requirements under article 3 2 of the R amp TTE Directive WEN 301 489 1 V1 5 1 Electromagnetic compatibility and Radio spectrum Matters ERM 2004 11 Electromagnetic compatibility EMC standard for radio equipment and WEN 301 489 17 V1 2 1 Services Part 17 Specific conditions for wideband data and 2002 08 HIPERLAN equipment WEN 50371 Generic standard to demonstrate the compliance of low power Electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic field 10MHz 300GHz General public WEN 60950 1 2001 Safety for information technology equipment including electrical A11 2004 business equipment E CE marking C E O Manufacturer Importer Signature Name Position Title Vice President
3. Connect Site survey displays all the active Access Points and IBSS in the neighborhood You can select one AP to associate Press Site Survey button to search the wireless device that this client want to connect Channel Number Allow user to set the channel manually or automatically If set channel manually just select the channel you want to specify If Auto is selected user can set the channel range to have Wireless Access Point automatically survey and choose the channel with best situation for communication All stations communicating with the Access Point must use the same channel when setup infrastructure of Client mode the channel number can not Be changed You have to go to AP mode to change the channel number Auto MAC Clone Check the box to enable MAC Clone for Single Ethernet Client Manual MAC Clone Enter the MAC Address of Single Ethernet Client Address Security Please refer the AP mode settings gt Security for details In client mode are not supported with RADIUS 802 1x authentication Wireless Security Setup Encryption WPA PSK TKIP D Dre Shared Dre Shared WPA PSK TKIP WPA PSK AES Group Key Apply Changes Reset Advance Setting Please refer the AP mode settings gt Advance Setting for details 29 WL5470AP User s Manual Bridge Mode Setting SE pes WLAN Access Point 4 A Mode Status TCP IP Reboot Other OvisLink Corp www ovislink com twa 1 Bri
4. Security setup Advanced Settings setup Apply Changes Reset 10 WL5470AP User s Manual Bridge Mode In this mode 2 access points in two remote locations connect to each other to provide a wireless bridge between 2 remote LANs It is mostly used by enterprise to connect 2 remote office s network together The bridge modes are connected by using either the WDS Wireless Distribution System or Ad Hoc topology This feature is also useful when users want to bridge networks between buildings where it is impossible to deploy network cable connections between these buildings To set the operation mode to Bridge Please go to Mode Bridge and click the button for configuration WLAN Access Point Mode Status TCP IP Reboot wwwevislink com twagl oy E Wireless Mode E reenen a est The PAS page is Used to SE C AP Setup Access Point C Client Setup Client Infrastructure Client Ad Hoc Bridge Setup Bridge WDS Repeater Setup WOS Repeater C Universal Repeater En Universal Repeater C WISP Setup WISP C WISP Universal Repeater Setup WISP Universal Repeater O GW Setup AP GATEWAY PEELLELE 1 WL5470AP User s Manual WDS Repeater Mode A repeater s function is to extend the wireless coverage of another wireless AP or router For WDS repeater to work the remote wireless AP Router must also support WDS function LH THREE lil il MIG Router To set
5. di Access Control Setup Annlu Channaa Reset Check the box to disable the Wireless LAN Interface by so doing you won t be able to make wireless connection with this Access Point in your located network In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only 2 4GHz B G 802 11b supported rate and 802 11g supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID It is case sensitive and must not exceed 32 characters A device will not be permitted to join the BSS unless it can provide the unique SSID An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network The default SSID is airlive Allow user to set the channel manually or automatically If set channel manually just select the channel you want to specify If Auto is selected user can set the channel range to have Wireless Access Point automatically survey and choose the channel with best situation for communication The number of channels supported depends on the region of this Access Point All stations communicating with the Access Point must use the same channel The default channel is 13 Wireles
6. 255 255 255 0 0 0 0 0 OFF 43 WL5470AP User s Manual Physical Address Band SSID Channel Number Encryption Associated Clients BSSID The time period since the device was up The current version of the firmware installed in this device There are 7 modes supported The default mode is Access Point If you want to change to other mode please click the Mode and select the wireless mode you want The number of channels supported depends on the region of this Access Point All Displays the total number of clients associated to this AP You can have up to 64 BSSID displays the ID of current BSS which uniquely identifies each BSS In AP mode this value is the MAC address of this Access Point LAN Configuration TCP IP Connection Method Physical Address IP Address Network Mask Default Gateway DHCP Server DHCP Start IP Address DHCP Finish IP Address Internet Configuration Connection Method Physical Address IP Address Network Mask Default Gateway Display the connection method you can setup in TCP IP section Display the LAN IP address you can setup in TCP IP section Display the network mask you can setup in TCP IP section Display the default gateway ip you can setup in TCP IP section Default the DHCP Server is enabled ON Display the DHCP server start IP address Display the DHCP server finish IP address Display the internet connection method you can setup in WISP mode
7. Date 2007 5 15 Stamp WL 5470AP CE Declaration Statement OvisLink Corp timto prohlaSuje Ze tento WL iuo OvisLink Corp deklaruoja kad is WL 5470AP Ge Czech 5470AP je ve shod se z kladn mi po adavky a GE atitinka esminius reikalavimus ir kitas 1999 5 EB dal mi p slu n mi ustanoven mi sm rnice Lithuanian Direktyvos nuostatas 1999 5 ES da Undertegnede OvisLink Corp erkl rer herved ml Hierbij verklaart OvisLink Corp dat het toestel WL Dansk Danish at f lgende udstyr WL 5470APoverholder de Nederlands Dutch 5470AP in overeenstemming is met de essenti le v sentlige krav og vrige relevante krav i eisen en de andere relevante bepalingen van richtlijn direktiv 1999 5 EF 1999 5 EG Hiermit erkl rt OvisLink Corp dass sich das mt Hawnhekk OvisLink Corp jiddikjara li dan WL Ger t WL 5470APin bereinstimmung mit den Mai Maltese 5470AP jikkonforma mal ti ijiet essenzjali u ma grundlegenden Anforderungen und den brigen provvedimenti o rajn relevanti li hemm fid Dirrettiva einschl gigen Bestimmungen der Richtlinie 1999 5 EC 1999 5 EG befindet K esolevaga kinnitab OvisLink Corp seadme hu Alul rott OvisLink Corp nyilatkozom hogy a WL Eesti Estonian WL 5470AP vastavust direktiivi 1999 5 EU Magyar 5470AP megfelel a vonatkoz alapvet p hin uetele ja nimetatud direktiivist tulenevatele Hungarian k vetelm nyeknek s az 1999 5 EC ir nyelv egy b teistele asjakohastele
8. EY oleellisten essenziali ed alle altre disposizioni pertinenti vaatimusten ja sit koskevien direktiivin muiden stabilite dalla direttiva 1999 5 CE ehtojen mukainen Ar o OvisLink Corp deklar ka WL 5470AP H r me l sir OvisLink Corp yfir v a WL 547 0AP atbilst Direkt vas 1999 5 EK b tiskaj m pras b m slenska Icelandic ler samr mi vi grunnkr fur og a rar kr fur sem un citiem ar to saist tajiem noteikumiem ger ar eru tilskipun 1999 5 EC H rmed intygar OvisLink Corp att denna WL no OvisLink Corp erkl rer herved at utstyret WL 5470AP st r verensst mmelse med de Norsk Norwegian 5470AP er i samsvar med de grunnleggende krav og v sentliga egenskapskrav och vriga relevanta vrige relevante krav i direktiv 1999 5 EF best mmelser som framg r av direktiv 1999 5 EG A copy of the full CE report can be obtained from the following address OvisLink Corp 5F No 6 Lane 130 Min Chuan Rd Hsin Tien City Taipei Taiwan R O C This equipment may be used in AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR This device uses software which is partly or completely licensed under the terms of the GNU General Public License The author of the software does not provide any warranty This does not affect the warranty for the product itself To get source codes please contact OvisLink Corp 5F No 96 Min Chuan Rd Hs
9. Hoc C Bridge Setup Bridge C WDS Repeater Setup WDS Repeater C Universal Repeater Setup Universal Repeater WISP WISP WISP Universal Repeater Setup WISP Universal Repeater PLLELLLE C GW SELH AP GATEWAY Wireless Mode J AP Select the AP and press Setup button for Wireless AP mode configuration Client Select the Client and press Setup button for Wireless Client mode pt amea Bridge Select the Bridge and press Setup button for Wireless Bridge mode me ees WDS Repeater Select the WDS Repeater and press Setup button for Wireless WDS Repeater We ds configuration Universal Repeater Select the Universal Repeater and press Setup button for Wireless Universal repeater mode configuration Select the WISP and press Setup button for WISP Client Router mode configuration WISP Universal Select the WISP Universal Repeater and press Setup button for WISP Repeater Universal Repeater mode configuration eu Select the GW and press Setup button for GW mode configuration 18 WL5470AP User s Manual AP Mode Setting WLAN Access Point OvisLink de 4 Mode Status TCP IP Reboot Other www ovislink eom ten s O Disable Wireless LAN Interface Band Channel Number AP Mode Settings Alias Name Wireless Ap Disable Wireless LAN Interface Band 2 4 GHz B G SSID lairlive Channel Number 13 IS Wireless Client Isolation Disabled Security Setup Advanced Settings setup
10. Life Time B6400 ser Apply Changes Reset Encryption You can select WPA PSK TKIP or WPA PSK AES method for data mm 3 Pre shared Key There are two formats for choice to set the Pre shared key i e Passphrase and Hex If Hex is selected users will have to enter a 64 characters string For easier A n the Passphrase at least 8 characters format is recommended Group Key Life Time Enter the number of seconds that will elapse before the group key change a Senet ere Encryption or WPA2 PSK authentication method is almost like WPA PSK You can choose the Pre Shared Key format and enter the Pre shared key Wireless Security Setup Encryption Mi T Pre Shared Key Format Passphrase Pre Shared Key EE Group Key Life Time B6400 sec Apply Changes Reset Wireless Security Setup Encryption B ISS AS Pre Shared Key Format Passphrase sl Pre Shared Key fe Group Key Life Time B6400 oer Apply Changes Reset 22 WL5470AP User s Manual Encryption You can select WPA2 PSK AES or WPA2 PSK Mixed method for data encryption Pre shared Key There are two formats for choice to set the Pre shared key e Passphrase and Hex If Hex is selected users will have to enter a 64 characters string For easier configuration the Passphrase at least 8 characters format is recommended Group Key Life Time Enter the number of seconds that will elapse before the group key change A Llmcay Mestanenutoweae Wireless Secu
11. Point Mode Status TCP IP Reboot Other OvisLink 3 wwwovislink zem twa i i Wireless Mode TE e maA Co cease Th his page ls Used to SE CAP Setup Access Point CG Client Setup Client Infrastructure Client Ad Hoc Bridge Setup Bridge C WDS Repeater Setup WDS Repeater C Universal Repeater Setup Universal Repeater WISP Setup WASP C WISP Universal Repeater Setup WISP Universal Repeater C GW Setup AP GATEWAY Belen WL5470AP User s Manual Client Mode Ad hoc If set to the Client Ad hoc mode this device can work like a wireless station when it is connected to a computer so that the computer can send packets from wired end to wireless interface You can share files and printers between wireless stations PC and laptop with wireless network adapter installed See the sample application below To set the operation mode to Client Ad Hoc Please go to Mode gt Client and click the button In the Network Type field select as infrastructure for configuration NA WLAN Access Point g f al i k Mode Status TCP IP Reboot Other OvisLink Corp EE Client Mode Settings A to Alias Hame Wireless AP l Disable Wireless LAN Interface Band 2 4 GHz B G Network Type infrastructure zl infrastructure SSID site Survey Channel Number T Auto Mac Clone Single Ethernet Client Manual MAC Clone 000000000000 Address
12. WDS Repeater Setup WDS Repeater Universal Repeater Setup Universal Repeater WISP emm WISP C WISP Universal Repeater Setup WISP Universal Repeater ERT C GW Setug AP GATEWAY 13 WL5470AP User s Manual WISP Client Router Mode WISP Client Router mode In WISP mode the AP will behave just the same as the Client mode for wireless function However Router functions are added between the wireless WAN side and the Ethernet LAN side Therefore The WISP subscriber can share the WISP connection without the need for extra router WISP P pc Outdoor AP E Client Router a To set the operation mode to WISP Please go to Mode WISP and click the button for configuration Air Live Ge oun 1 L Mode Status TCP IP Reboot Other sLink D worw ovislink com teag Wireless Mode C AP Setup Access Point C Client etn Client Intrastructure Client Ad Hoc Bridge Setup Bridge C WDS Repeater SEP WDS Repeater C Universal Repeater Sep Universal Repeater e WISP WISP C WISP Universal Repeater Stelle WISP Universal Repeater C GW Setup AP GATEWAY 14 WL5470AP User s Manual WISP Universal Repeater Mode In this mode the AP behaves virtually the same as the WISP mode except one thing the AP can also send wireless signal to the LAN side That means the AP can connect with the remote WISP AP and the indoor wireless card and then provide IP sharing capa
13. WISP Outdoor AP SSID manually or click the site survey button to connect and get SSID automatically Channel Number The number of channels supported depends on the region of this Access Point All A E communicating with the Access Point must use the same channel Wireless Client When enabled the wireless clients are separated from each other Please refer a E AP mode settings gt Wireless Client Isolation for details Advance Setting Please refer the AP mode settings gt Advance Setting for details static hostname allowing your device to be more easily accessed by specific name When this function is enabled the IP address in DDNS Server will be automatically updated with the new IP address provided by ISP Ping is a network tool used to test whether a particular host is reachable across an IP network DoS setting In WL5470AP a denial of service attack DoS attack can block or limit the ien sending network flood to your local computer Diagnostics The nslookup command can be used in diagnostics to find the IP addresses of a particular computer using DNS lookup The name means name server lookup nn most common version of the program is included as part of the BIND package ilteri The URL filter database is used for internet filtering that blocks access to MAC Filter Enables you to allow or deny Internet access to users within the LAN The IP filter function enables you to define a minimum and maximum IP address range
14. ianea asias 36 WISP UNIVERSAL REPEATER MODE SETTING 39 OW MODE E RRC 41 EE 43 A tec eaa E ves scseac mea veces oases eee eee 46 Fe it EE 48 EE 49 3 WL5470AP User s Manual Introduction WL 5470AP is world s most popular multi function access point lt features an impressive total of 8 wireless multi function modes that are not available in normal access point In addition the ACK timeout and RSSI feature makes it suitable for long distance application From ordinary AP application to Hotspot and WISP usage you will find the WL 5470AP is the device you want WL 5470AP is an IEEE802 11b g compliant 11 Mbps amp 54 Mbps Ethernet Wireless Access Point The Wireless Access Point is equipped with two 10 100 M Auto sensing Ethernet ports for connecting to LAN and also for cascading to next Wireless Access Point WL 5470AP provides 64 128bit WEP encryption WPA PSK WPA2 PSK and IEEE802 1x which ensures a high level of security to protect users data and privacy The MAC Address filter prevents the unauthorized MAC Addresses from accessing your Wireless LAN Your network security is therefore double assured The web based management utility is provided for easy configuration that your wireless network connection is ensured to be always solid and hassle free 1 WL5470AP User s Manual GE A A SS YS e e e Be H Pp ewer YY eS 4x100Mbps LAN ports for Wireless AP cascade 2MB flash 16MB SDRAM TX output power is limited
15. in the table won t be able to associate with the AP MAC Address Enter the MAC Address of a station that is allowed to access this Access Point Commet You may enter up to 20 characters as a remark to the previous MAC Address Apply Changes Press to save the new settings on the screen Press to discard the data you have entered since last time you press Apply Change Delete Selected To delete clients from access to this Access Point you may firstly check the Select checkbox next to the MAC address and Comments and press Delete Selected Delete All To delete all the clients from access to this Access Point just press Delete All without selecting the checkbox Reset If you have made any selection press Reset will clear all the select mark 27 WL5470AP User s Manual Client Mode Setting WLAN Access Point Mode Status TCP IP Reboot Other Client Mode Settings 5 page s LS sed ta E ent EE Alias Name Wireless AP l Disable Wireless LAN Interface Band 2 4 GHz B 6 Network Type Infrastructure zl SSID faine sis Site Survey Channel Number 13 i l Auto Mac Clone Single Ethernet Client Manual MAC Clone 0000000000 Address Security setup Advanced Settings setup ose Alias Name You can set the alias name for this device limited not exceed 32 characters O Disable Wireless Check the box to disable the Wireless LAN Interface by so doing you won t be LAN Interface able to mak
16. party for a charge no more than your cost of physically performing source distribution a complete machine readable copy of the corresponding source code to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or c Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer in accord with Subsection b above The source code for a work means the preferred form of the work for making modifications to it For an executable work complete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable If distribution of executable or object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place counts as distribution of the source code even though third parties are not compe
17. physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee 2 You may modify your copy or copies of the Program or any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions a You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change b You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third parties under the terms of this License c If the modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Program itself is interactive but does not normally print such an announcement your work based on the Program is not required to print an announcement These requirements apply to the modified work as a whole If identifiable sections of that work are not derived fr
18. referred to as a network name because essentially it is a name that identifies a wireless network The number of channels supported depends on the region of this Access Point All stations communicating with the Access Point must use the same channel When enabled the wireless clients are separated from each other Please refer the AP mode settings gt Wireless Client Isolation for details 32 WL5470AP User s Manual Security Please refer the AP mode settings gt Security for details This setting is use between Wireless client and this device Wireless Security Setup Encryption None El None Apply Cour WPA PSK TKIP WPA PSK AES WDS Security Please refer to the Bridge mode settings gt WDS Security for details This setting is use between both wireless AP Router devices WDS Security Setup Encryption WEP Key Format WEP Key Pre Shared Key Format Pre Shared Key Apply Changes Close Reset Advance Setting Please refer the AP mode settings gt Advance Setting for details Access Control Please refer the AP mode setting gt Access Control for details AP MAC Address Enter 12 digits in hex numbers in the AP MAC address BSSID field and press the Add MAC Address Button to associate with other s Wireless access point Before you want to use bridge mode to connect each other to provide A wireless bridge between 2 remote LANs you need add the BSSID of other s wireless AP first Del
19. the operation mode to WDS Repeater Please go to Mode gt WDS Repeater and click the button for configuration TR Lina WLAN Access Point OvisLink Y worw ovislink com tw Mode Status TCP IP Reboot Other Wireless Mode CAP SEHH Access Point C Client Sep Chent Infrastructure Client Ad Hoc C Bridge Setup Bridge GG WDS Repeater WDS Repeater C Universal Repeater En Universal Repeater C WISP Setup WISP C WISP Universal Repeater Setup WISP Universal Repeater C GW AP GATEWAY 12 WL5470AP User s Manual Universal Repeater Mode A universal repeater can also extend the wireless coverage of another wireless AP or router But the universal repeater does not require the remote device to have WDS function Therefore it can work with almost any wireless device Note When you are using the universal repeater mode please make sure the remote AP Router s WDS function is turned off A EE EEN EE EE EEN E ER REENEN AY CAY cq _ Router Universal Repeater To set the operation mode to Universal Repeater Please go to Mode Universal Repeater and click the button for configuration e D Air Live 1 L Mode Status TCP IP Reboot Other OvisLink Corp 1 worw ovislink com tea WLAN Access Point Wireless Mode to CAP Seip Access Paint C Client Setup Client Infrastructure Client Ad Hoc C Bridge Setup Bridge C
20. 301 USA Also add information on how to contact you by electronic and paper mail If the program is interactive make it output a short notice like this when it starts in an interactive mode Gnomovision version 69 Copyright C year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY for details type show w This is free software and you are welcome to redistribute it under certain conditions type show c for details The hypothetical commands show w and show c should show the appropriate parts of the General Public License Of course the commands you use may be called something other than show w and show C they could even be mouse clicks or menu items whatever suits your program You should also get your employer if you work as a programmer or your school if any to sign a copyright disclaimer for the program if necessary Here is a sample alter the names Yoyodyne Inc hereby disclaims all copyright interest in the program Gnomovision which makes passes at compilers written by James Hacker signature of Ty Coon 1 April 1989 Ty Coon President of Vice This General Public License does not permit incorporating your program into proprietary programs If your program is a subroutine library you may consider it more useful to permit linking proprietary applications with the library If this is what you want to do use the GNU Lesser General Public License instead of this License FCC Certificat
21. 70AP User s Manual Wireless Security Setup Encryption WEP Authentication Type Key Length Key Format Hex 10 characters Default Tx Key Key 1 Encryption Key 1 ae Encryption Key Encryption Key 3 Encryption Key 4 Apply Changes Reset You can select Open System or Shared Key type for authentication You can set 64bit or 128bit Encryption Select ASCII if you are using ASCII characters case sensitive Select HEX if you are using hexadecimal numbers 0 9 or A F 10 hexadecimal digits or 5 ASCII characters are needed if 64 bit WEP is used 26 hexadecimal digits or 13 ASCII characters are needed if 128 bit WEP is used Shared Key is used when both the sender and the recipient share a secret key So you can choose Open system or one Shared Key authentication method Encryption or Wi Fi Protected Access WPA with Pre Shared Key PSK provides better security than WEP keys It does not require a RADIUS server in order to provide association authentication but you do have to enter a shared key for the authentication purpose The encryption key is generated automatically and dynamically Wireless Security Setup Encryption APA PS TIP Pre Shared Key Format Passphrase sl Pre Shared Key Group Key Life Time B6400 sec _ Apply Changes Reset 21 WL5470AP User s Manual Wireless Security Setup Encryption AESI Pre Shared Key Format Passphrase Pre Shared Key Group Key
22. Configuration DHCP Client D Attain DNS Automatically C Set DNS Manually See 000000000000 Respond to WAN Ping Enable UPnP Enable IPsec pass through on YPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection WAN Access Type DNS 1 DNS 2 DNS 3 Clone MAC Address I A AAK Save Reset You can select many WAN Access Type Static IP DHCP Client PPPOE PPTP and L2TP for WAN connection depend on you WISP provided Virtual Servers IT Enable Virtual Servers Servers Local IP Address Protocol Port Range Description Reset Current Virtual Servers ocal IP Table Protocol 0 EE Address Ranas Description Select Delete All Reset In WISP mode you can setup and enable Virtual server function Like Web FTP Delete Selected Email DNS Telnet server Select one virtual server type and enter the Local IP address Local Port Range and click the save button Special Applications Incoming Incoming Start Incoming End Trigger Trigger End Type Port Port Type Port Sule Dialpad O Paltalk O BOTH e x BOTH e xI BOTH 7 xI UDP 8 HIN m E E E You can enable some system default special application like Qucktime 4 37 WL5470AP User s Manual Audio Video application Dialpad internet phone service or define the special application man
23. THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program and you want it to be of the greatest possible use to the public the best way to achieve this is to make it free software which everyone can redistribute and change under these terms To do so attach the following notices to the program It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty and each file should have at least the copyright line and a pointer to where the full notice is found one line to give the program s name and an idea of what it does Copyright C yyyy name of author This program is free software you can redistribute it and or modify it under the terms of the GNU General Public License as published by the Free Software Foundation either version 2 of the License or at your option any later version This program is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE See the GNU General Public License for more details You should have received a copy of the GNU General Public License along with this program if not write to the Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1
24. UTION AND MODIFICATION 0 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License The Program below refers to any such program or work and a work based on the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you Activities other than copying distribution and modification are not covered by this License they are outside its scope The act of running the Program is not restricted and the output from the Program is covered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 1 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License along with the Program You may charge a fee for the
25. an choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only O 2 4GHz B G 802 11b supported rate and 802 11g supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID In WISP mode you have to enter the WISP Outdoor AP SSID manually or click the site survey button to connect and get SSID automatically for details Enter the MAC Address of Single Ethernet Client 39 WL5470AP User s Manual SSID airlive site Survey Enable E tion O Oe rant tren ze Enable Encryption On Both WAN and WLAN side SE WLAN side only 7 Advanced Settings WAN side onl You can designate security to use for WLAN side WAN side or both sides Both WAN and WLAN side The security is used on both the WISP and the Wireless Client PC side connection WLAN side only The security used on wireless client connection only The WISP side is not encrypted WAN side only The security used on WISP connection only The WLAN side is not encrypted Security Please refer the AP mode settings gt Security Survey for details A mz Plaseroterie WISP mode setings gt DMZ Setingfordetals A0 WL5470AP User s Manual GW Mode Setting Air Liwe E OvisLink Corp KA WLAN Access Point i Mode Sta
26. ation before a client associates The advantage Is that the client reduces the time that it s disconnected to the network Authentication RADIUS Enter the RADIUS Server IP address and Password provided by your ISP Port Enter the RADIUS Server s port number provided by your ISP The default is 1812 IP Address Enter the RADIUS Server s IP Address provided by your ISP Password Enter the password that the AP shares with the RADIUS Server Accounting RADIUS Enter the Accounting RADIUS Server IP address and Password provided by your Server ISP Advanced Settings Press the setup button for detail configurations Wireless Advanced Settings Fragment Threshold Du 256 2346 RTS Threshold 2347 02347 Beacon Interval nm O 20 1024 ms Inactivity Time s0000 100 50480000 ms Data Rate Auto y Preamble Type Long Preamble Short Preamble Broadcast SSID Enabled Disabled IAPP GG Enabled Disabled 802 114 Protection DG Enabled Disabled Tx Power Level Default About 18dB Enable WatchDog Watch Interval fi 1 60 minutes Watch Host f 0 255 D Auto adjustment Unit 4usec set Default Ack timeout Apply Changes Reset It is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wi
27. bility all at the same time However the output power is divided between 2 wireless sides and proper antenna installation can influence the performance greatly WISP Outdoor AP K WISP Universa To set the operation mode to WISP Universal Repeater Please go to Mode gt WISP Universal Repeater and click the button for configuration Air Live D SI L Mode Status TCP IP Reboot Other OvisLink v 2 worw ovislink com tw WLAN Access Point Wireless Mode CAP SEN Access Paint Client Sep Client Infrastructure Client Ad Hoc C Bridge Setup Bridge C WDS Repeater SELH WDS Repeater C Universal Repeater SEH Universal Repeater C WISP Setup WISP WISP Universal Repeater Setup WISP Universal Repeater C GW Sep AP GATEWAY 15 WL5470AP User s Manual GW Mode In this mode the AP behaves virtually the same as the WISP mode except one thing the AP can also send wireless signal to the LAN side That means the AP can connect with the remote WISP AP and the indoor wireless card and then provide IP sharing capability all at the same time However the output power is divided between 2 wireless sides and proper antenna installation can significantly improve the performance WISP Outdoor WISP Universa To set the operation mode to GW Mode Please go to Mode gt GW and click the button for configuration Air Live D sl 1 L Mod
28. dge Mode Settings Alias Name Wireless AP Disable Wireless LAN Interface Band 2 4 GHz B Channel Number 13 902 1d Spanning Tree Disabled D WDS Security Setup Adwanced Settings setup Apply Changes Reset AP MAC Address Site Survey Comment Add MAC Address Reset Show Statistics Alias Name You can set the alias name for this device limited not exceed 32 characters O Disable Wireless Check the box to disable the Wireless LAN Interface by so doing you won t be LAN Interface able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only 2 4GHz B G 802 11b supported rate and 802 119 supported rate The default is 2 4GHz B G mode Channel Number In Bridge mode both wireless AP Router device need set to the same Channel e Security Please refer the AP mode settings gt Security for details kass etn WDS Security To enable security between wireless AP Router you can select WEP 64bits WEP 128bits WPA TKIP WPA2 AES for data encryption For WEP encryption Select ASCII if you are using ASCII characters Select HEX if you are using hexadecimal numbers 0 9 or A P For WPA WPA2 encryption you need enter the Pre Shared Key Information for the authe
29. e Status TCP IP Reboot Other OvisLink v 2 worw ovislink com tw WLAN Access Point Wireless Mode CAP SELH Access Point Client Sep Client Infrastructure Client Ad Hoc C Bridge Setup Bridge C WDS Repeater SELH WDS Repeater C Universal Repeater SEIH Universal Repeater C WISP Setup WISP C WISP Universal Repeater Setup WISP Universal Repeater GW AP GATEWAY 16 WL5470AP User s Manual Configuration 1 Start your computer Connect an Ethernet cable between your computer and the Wireless Access Point 2 Make sure your wired station is set to the same subnet as the Wireless Access Point Le 192 168 100 X 3 Start your WEB browser In the Address box enter the following http 192 168 100 252 Ed The configuration menu is divided into five categories Mode Status TCP IP Reboot and Other Click on the desired setup item to expand the page in the main navigation page The setup pages covered in this utility are described below ETS E WLAN Access Point iy Mode Status TCP IP Reboot OvisLink Corp wereovrialink com tw E A Thank you for using WLAN Access Point 17 WL5470AP User s Manual You can choose and setup different wireless mode for detail configurations ir Live WLAN Access Point A 4 TENESTER OvisLink Corp i werw evislink eom tea a Wireless Mode Ge AP Setup Access Point Client Seip Client Infrastructure Client Ad
30. e wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 119 supported rate only 2 4GHz B G 802 116 supported rate and 802 119 supported rate The default is 2 4GHz B G mode Network Type Client mode have two Network type Infrastructure A wireless network that is built around one or more access points providing wireless clients access to wired LAN or Internet service It is the most popular WLAN network structure today AdHoc wireless network do not use wireless AP orrouter as the central hub of the network Instead wireless client are connected directly to each other The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID It is case sensitive and must not exceed 32 characters A device will not be permitted to join the BSS unless it can provide the unique SSID An SSID is also referred to as a network name because essentially it is a name that identifies a wireless 28 WL5470AP User s Manual ro Site Survey Wireless Site Survey ative O0416204 cb 55 h B 0 AP Ee mf wlan 00 20 e0 39 a1 bb 3 B AP WEP 26 default 00 c0 02 fe 43 68 40 Ga AP na 16 PLANET 00 18 7 11 43 d6 11 B G AP WEP 15
31. eless AP Disable Wireless LAN Interface Band 2 4 GHz Dis SSID airlive Site Survey Clone MAC Address fO00000000000 Security setup Advanced Settings setup Wan Port Setup Virtual Server Setup Special Application Setup DM Setup Se Reset Apply Changes Reset able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 119 supported rate only 2 4GHz B G 802 11b supported rate and 802 119 supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID In WISP mode you have to enter the WISP Outdoor AP SSID manually or click the site survey button to connect and get SSID automatically Site Survey Please refer the Client mode settings Site Survey for details MAC Clone Address Enter the MAC Address of Single Ethernet Client Security Please refer the AP mode settings gt Security Survey for details Not supported with RADIUS 802 1x authentication 36 WL5470AP User s Manual Advance Setting Please refer the AP mode settings gt Advance Setting for details WAN port Virtual Server Special Application WAN Port
32. ested transmission If the Hidden Node problem is an issue please specify the packet size The RTS mechanism will be activated if the data size exceeds the value you set The default value is 2347 Warning Enabling RTS Threshold will cause redundant network overhead that could negatively affect the throughput performance instead of providing a remedy This value should remain at its default setting of 2347 Should you encounter inconsistent data flow only minor modifications of this value are recommended Beacon Interval Beacon Interval is the amount of time between beacon transmissions Before a station enters power save mode the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point Data Rate By default the unit adaptively selects the highest possible rate for transmission Select the basic rates to be used among the following options Auto 1 2 5 5 110r 54 Mbps For most networks the default setting is Auto which is the best choice When Auto is enabled the transmission rate will 25 WL5470AP User s Manual select the optimal rate If obstacles or interference are present the system will automatically fall back to a lower rate Preamble Type A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter In a noisy network environmen
33. ete Selected To delete bridge from access to this Access Point you may firstly check the Select Delete All To delete all the clients from access to this Access Point just press Delete All 33 WL5470AP User s Manual Universal Repeater Mode Setting ir Live al i Mode Status TCP IP Reboot OvisLink Corp t WLAN Access Point A tini Alias Name WDS Repeater Mode Settings Alias Name Wireless_AP T Disable Wireless LAN Interface Band 2 4 GHz B G SSID finie S Channel Number ha d Wireless Client Isolation Disabled 902 1d Spanning Tree Disabled zl Security setup WDS Security setup Advanced Settings setup MEET Access Control Setup Apply Changes Feset You can set the alias name for this device limited not exceed 32 characters O Disable Wireless Check the box to disable the Wireless LAN Interface by so doing you won t be LAN Interface Channel Number SSID of extended Interface able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only 2 4GHz B G 802 11b supported rate and 802 11g supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all acces
34. filter all IP addresses falling within the range are not allowed Internet access 42 WL5470AP User s Manual In this screen you can see the current settings and status of this Access Point You can change settings by selecting specific tab described in below Se Live WLAN Access Point Mode Status TCP IP Reboot Other OvisLink y system statistics Active Clients weew ovislink com wet System Data Thie mada chac ha ANS Page SCS ine current status and System System em 3 L em Zell e St em of ine device Uptime Firmware Version Wireless Mode Physical Address Band SSID Channel Number Encryption Associated Clients BSSID LAN Configuration Connection Method Physical Address Oday 0h 4m 5bs v49 2 3 5 1eu A AP 00 41 62 Uer 76 2 4 GHz B airlive 13 Disabled O 00 462 De 00 76 Fixed IP UU 4f 62 08 88 76 IP Address 192 166 100 252 Network Mask 255 255 255 0 Default Gateway 0 0 0 0 DHCP Server OFF System Data System Uptime Oday Oh 4m 5bs Firmware Version Wireless Mode Physical Address Band SSID Channel Number Encryption Associated Clients BSSID LAN Configuration Connection Method Physical Address IP Address Network Mask Default Gateway DHCP Server 19 2 3 3 1eu b 2 AP 00 46 De 00 76 2 4 GHz Gr airlive 13 Disabled O 00462 De 00 76 Fixed IP OU 4fb2 0e 00 76 192 168 100 252
35. frame from the remote station If the ACK is NOT received within that timeout period then the packet will be re transmitted resulting in reduced throughput If the ACK setting is too high then throughput will be lost due to waiting for the ACK Window to timeout on lost packets By having the ability to adjust the ACK setting we can effectively optimize the throughput over long distance links This is especially true for 802 11a and 802 11g networks You can set as default for auto adjustment Press to save the new Settings on the screen Press to discard the data you have entered since last time you press Apply Change Access Control Press the setup button for detail configurations 26 WL5470AP User s Manual Wireless Access Control Wireless Access Control Mode Disable MAC Address Comment Apply Changes Reset Current Access Control List MAC Address Comment select Delete All Reset When Enable Wireless Access Control is checked only those clients whose wireless MAC addresses listed in the access control list can access this Access Point If the list contains no entries with this function being enabled then no clients will be able to access this Access Point Wireless Access Control Select the Access Control Mode from the pull down menu Disable Select to disable Wireless Access Control Mode Allow Listed Only the stations shown in the table can associate with the AP Deny Listed Stations shown
36. gt WAN Port configuration Display the AP MAC address information Display the internet IP Address you can setup in WISP mode gt WAN Port configuration Display the network mask you can setup in WISP mode gt WAN Port configuration Display the default gateway you can setup in WISP mode gt WAN Port configuration 44 WL5470AP User s Manual Statistics Statistics Sent Packets 1380 Wireless L4N Received Packets 5679 Sent Packets Ethernet L4N Received Packets see E Ethernet WAN Recelwved Packets Received Packets 4858 Refresh The Statistics table shows the packets sent received over wireless and ethernet LAN respectively Active Clients Display the active Wireless Clients information Saving information Active VVireless Client Table MAC Address E Tx Packet i Rx Packet E Tx Rate Mbps E Power Saving None Refresh 45 Wireless MAC address Tx Rx Packet Tx Rate and Power WL5470AP User s Manual OvisLink y Alsen a LAN Interface Setup IP Address 192 168 100 252 Subnet Mask 255 255 2550 Default Gateway booo DHCP Server El gereerp Dnnn DHCP Client Range 192 168 100 100 192 168 100 200 Shaw Client DNS Server Clone MAC Address 000000000000 Apply Changes Reset In this page you can change the TCP IP settings of this Access Point select to enable disable the DHCP Client 802 1d Spanning Tree and Clone MAC Address IP Add
37. in Tien City Taipei Taiwan R O C A fee will be charged for production and shipment for each copy of the source code GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your freedom to share and change it By contrast the GNU General Public License is intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This General Public License applies to most of the Free Software Foundation s software and to any other program whose authors commit to using it Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead You can apply it to your programs too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you know you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you the
38. ions This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTI ON Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including i
39. ktop D e E rt El EI EI My Documents KM Computer ES My Documents RS My Computer History GE My Network Places History GE My Network Places E al config Desktop Gr Desktop My Documents My Documents My Computer My Computer Ae ES ns File name v File name Ss X My Network P My Network P Save as type ES Document y Cancel Files of type fan Files y Cancel Si L KE Reset Settings to Default Click button to restore the default configuration Password Password Setup Confirmed Password fs For secure reason It is recommended that you set the account to access the web server of this Access Point Leaving the password blank will disable the protection The login screen prompts immediately once you finish setting password Remember your password for you will be asked to enter them every time you access the web server of this Access Point New Password Set your new password Password can be up to 30 characters long Password can contain letter number and space It is case sensitive Confirm Password Re enter the new password for confirmation Note when you setup the password and click the apply change button system will pop up Window and ask the username and password Please enter system default username admin not changeable and your password for entering the configuration WEB UI Log system Log This page can be used to set remote log server and
40. ling to distribute software through any other system and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8 If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 9 The Free Software Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation If the Program does not specify a version number of this License you may choose any version ever published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution condi
41. lled to copy the source along with the object code 4 You may not copy modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify sublicense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 5 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions are prohibited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it 6 Each time you redistribute the Program or any work based on the Program the recipient automatically receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License 7 lf as a consequence of a court judgment or allegation of pa
42. n static when associated with a station and blink whenever this AP receives data packets in the air If the Status LED glows after self test it means the Wireless Access Point fails on self test Please ask your dealer for technical support 4 Please make sure your computer IP is in the same subnet as the AP i e 192 168 100 x 5 please make sure your computer has wireless network adapter installed 6 Open the web browser and enter http 192 168 100 252 6 WL5470AP User s Manual About the Wireless Operation Modes The WL 5470AP v2 device provides all 7 modes of wireless operational applications with Access Point Mode Client Mode Bridge Mode WDS Repeater Mode Universal Repeater Mode WISP Client Router Mode WISP Universal Repeater Mode GW Mode CON OO Om BP Ga DO eh This device is shipped with configuration that is functional right out of the box If you want to change the settings in order to perform more advanced configuration or even change the mode of operation you can use the web based utility provided by the manufacturer as described in the following sections 7 WL5470AP User s Manual Access Point Mode When acting as an access point default setting this device connects all the stations PC notebook with wireless network adapter to a wired network All stations can have the Internet access if only the Access Point has the Internet connection See the sample application below Access Poi
43. nt Mode gt hemo Ethernet AE ADSL f Cable Modem Internet To set the operation mode to Access Point please go to Mode gt AP and click the button Air Live EE 4 Mode Status TCP IP Reboot Other OvisLink Ly id Wireless Mode o EN a ele Als page is Used ta set rent als oda AP Setup Access Point Client Setup Client Infrastructure Client Ad Hoc C Bridge Setup Bridge C WDS Repeater Setup WDS Repeater C Universal Repeater setup Universal Repeater C WISP Setup WISP C WISP Universal Repeater Setup WISP Universal Repeater DO C GW Setup AP GATEWAY 00 WL5470AP User s Manual Client Mode Infrastructure If set to Client Infrastructure mode this device can work like a wireless station when it s connected to a computer so that the computer can send packets from wired end to wireless interface Refer to the illustration below This station AP1 plus the connected computer 1 can associate to another Access Point AP2 and then can have the Internet access if the other Access Point AP2 has the Internet connection Client Mode Infrastructure um Ethernet Mi iiem gt SC ar ADSL Cable Modem puter 1 To set the operation mode to Client Infrastructure Please go to Mode gt Client and click the button In the Network Type field select as infrastructure for configuration ae oes WLAN Access
44. nterference that may cause undesired operation FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures All trademarks and brand names are the property of their respective proprietors Specifications are subject to change without prior notification WL5470AP User s Manual Table of Contents INTRODUCTION e el a l EE Ee 2 PARTS NAMES AND E Be LE 3 FACTORY DEFAULT NO O 5 A EE 5 HARDWARE CONNECTION iara NE ss RA NEE AEA 6 ABOUT THE WIRELESS OPERATION MODES nadaa dde 7 ACCESSPOINT MODE iiO 8 CHUENT MODE INFRASTRUCTURE os 9 CUENTMODE AD HOO invariantes rene 10 Eiere aere 11 WDS REPEATER MODE e leal 12 UNIVERSAL REPEAT ee 13 WISP CEIENT ROUTER MODE eet 14 WISPUNVERSAC REPEATER MODE EE 15 COW MODE rensar a a a dees lauald den Lencuelaea tie Seiten a datas ealaekeee 16 CONEIGURA TION ees 17 Ver 18 AP MODE SETTING didas 19 SP A A O to ET 20 IN A racic ta saa aoa ea oe ca ca Pato ecw nae ws so ea aad Saat eee 24 EEN EE 28 BRIDGE MODE SETTING a A 30 WDS REPEATER MODE EE 32 UNIVERSAL REPEATER MODE SETTING ee 34 WISP CLIENT ROUTER MODE SETTING
45. ntication purpose 30 WL5470AP User s Manual WDS Security Setup Encryption WEP Key Format WEP Key Pre Shared Key Format Pre Shared Key Apply Changes Close Reset Advance Setting Please refer the AP mode settings gt Advance Setting for details AP MAC address Enter 12 digits in hex numbers in the AP MAC address BSSID field and press the Add MAC Address Button to associate with other s Wireless access point Before you want to use bridge mode to connect each other to provide A wireless bridge between 2 remote LANs you need add the BSSID of other s wireless AP first Site Survey Site survey displays all the active Access Points and IBSS in the neighborhood Press Site Survey button to search the wireless device Wireless Site Survey sem BSSID_ Channel Type Signal PLANET 00 18 e7 11 43 d6 11 B G AP WEP Zb default 00 c0 0 2te d3 66 10 B 51 AP na 18 wlan 00 20 e0 39 a1 bb 3 UE AP WEP 16 Refresh Add MAC Address Enter MAC address of remote access point Press to discard the data you have entered since last time you press Apply Change Show Statisties Ustallpactelsinfomaton orrae Delete Selected To delete bridge from access to this Access Point you may firstly check the Select eg Delete All To delete all the clients from access to this Access Point just press Delete All ee ses 31 WL5470AP User s Manual WDS Repeater Mode Setting Air Live
46. om the Program and can be reasonably considered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following a Accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or b Accompany it with a written offer valid for at least three years to give any third
47. p or outside internet mt Bomemaene OOOO O Table 2 Connection Ports 4 WL5470AP User s Manual Factory Default Settings Device Name WL 5470AP WEP Default value Disabled DHCP Server e In AP Client Repeater and GW mode the default DHCP Server is disabled Please set your PC s IP to the same subnet as the AP to access the AP In WISP mode the default DHCP server is enabled Please restart your PC to renew the IP address DHCP Server IP Range 192 168 100 100 192 168 100 200 Table 3 Default Setting 5 WL5470AP User s Manual Hardware Connection Note Before you starting hardware connection you are advised to find an appropriate location to place the Access Point Usually the best place for the Access Point is at the center of your wireless network with line of straight to all your wireless stations Also remember to adjust the antenna usually the higher the antenna is placed the better will be the performance 1 Connect to your local area network connect an Ethernet cable to one of the Ethernet port 2 LAN1 to LAN4 of this Wireless Access Point and the other end to a hub switch router or another wireless access point 3 Power on the device connect the included AC power adapter to the Wireless Access Point s power port and the other end to a wall outlet Check the LED The Power and LAN LED should be ON LAN LED will even blink if there is traffic The Link Act LED will be on i
48. reless network If your 802 11g Wireless LAN PC Card often transmit large files in wireless 24 WL5470AP User s Manual network you can enter new Fragment Threshold value to split the packet The value can be set from 256 to 2346 The default value is 2346 RTS Threshold RTS Threshold is a mechanism implemented to prevent the Hidden Node problem Hidden Node is a situation in which two stations are within range of the same Access Point but are not within range of each other Therefore they are hidden nodes for each other When a station starts data transmission with the Access Point it might not notice that the other station is already using the wireless medium When these two stations send data at the same time they might collide when arriving simultaneously at the Access Point The collision will most certainly result in a loss of messages for both stations Thus the RTS Threshold mechanism provides a solution to prevent data collisions When you enable RTS Threshold on a suspect hidden Station this station and its Access Point will use a Request to Send RTS The station will send an RTS to the Access Point informing that it is going to transmit the data Upon receipt the Access Point will respond with a CTS message to all station within its range to notify all other stations to defer transmission lt will also confirm the requestor station that the Access Point has reserved it for the time frame of the requ
49. ress This field can be modified only when DHCP Client is disabled If your system manager assigned you static IP settings then you will have to enter the information provided Subnet Mask Enter the information provided by your system manager Default Gateway Enter the information provided by your system manager Select Disable Client or Server from the pull down menu Disable Select to disable DHCP server function Client Select to automatically get the LAN port IP address from ISP For ADSL Cable Modem Server Select to enable DHCP server function DHCP Client Range WL 5060AP IP addresses continuing from 192 168 100 1 to 192 168 100 253 Show Client Click to show Active DHCP Client table DNS Server Enter the Domain Name Service IP address 802 1d Spanning Tree To enable 802 1d Spanning Tree will prevent the network from infinite loops Infinite loop will happen in the network when WDS is enabled and there are multiple active paths between stations 46 WL5470AP User s Manual Clone MAC Address You can specify the MAC address of your Access Point to replace the factory setting 47 WL5470AP User s Manual Click the button to restart device Live WLAN Access Point Mode Status TCP IP Reboot Other OvisLink Corp 3 A ee a a Reboot System Anytime YOu want to warn boot His device Hor any purposes Reboot System Reboot 48 WL5470AP User s Manual r Mode Status TCP IP tica
50. rity Setup Encryption 802 1 RADIUS Security Authentication RADIUS Server Port 1812 IP address Password l Enable Accounting Accounting RADIUS Server Port yiais IP address Password Apply Changes Reset Wireless Security Setup Encryption 802 1 RADIUS y SEN None y e WPA AES AccountinyyPA2 AES WPA Mixed ASES ME et Encryption 802 1x 802 1x RADIUS security You can select None WEP WPA TKIP WPA AES WPA2 AES WPA2 Mixed method for data encryption Encryption None No data encryption and Use 802 1x Authentication is disable Encryption 802 1x Authentication is enabled and the RADIUS Server will proceed to check the 802 1x Authentication and make the RADIUS server to issue the WEP key dynamically You can select WEP 64bits or WEP 128bits for data encryption Encryption WPA TKIP WPA AES WPA RADIUS authentication use WPA Wi Fi Protect Access data encryption for 802 1x authentication 23 WL5470AP User s Manual WPA is an encryption standard proposed by WiFi for advance protection by utilizing a password key TKIP or certificate It is more secure than WEP encryption Encryption WPA2 AES WPA2 Mixed The two most important features beyond WPA to become standardized through 802 11i WPA2 are pre authentication which enables secure fast roaming without noticeable signal latency Pre authentication provides a way to establish a PMK security associ
51. s tetele eldirasainak Hereby OvisLink Corp declares that this WL o Niniejszym OvisLink Corp o wiadcza ze WL 5470AP 5470AP is in compliance with the essential Polski Polish jest zgodny z zasadniczymi wymogami oraz requirements and other relevant provisions of pozostatymi stosownymi postanowieniami Dyrektywy Directive 1999 5 EC 1999 5 EC Por medio de la presente OvisLink Corp declara pt OvisLink Corp declara que este WL 5470APesta que el WL 5470APcumple con los requisitos Portugu s conforme com os requisitos essenciais e outras esenciales y cualesquiera otras disposiciones Portuguese disposi es da Directiva 1999 5 CE aplicables o exigibles de la Directiva 1999 5 CE ME THN MAPOY2A OvisLink Corp AHAONEI sl OvisLink Corp izjavlja da je ta WL 5470AP v skladu OTI WL 5470AP 2 gt YMMOPOONETAI NPOZ TI Slovensko z bistvenimi zahtevami in ostalimi relevantnimi OYZIOAEI2 ANAITH2E12 KAI TI2 AOINE Slovenian dolocili direktive 1999 5 ES 2XETIKE2 AIATA EI2 TH OAHTIAZ 1999 5 EK Par la pr sente OvisLink Corp d clare que OvisLink Corp t mto vyhlasuje Ze WL 5470AP spina z kladn po iadavky a v etky pr slu n ustanovenia exigences essentielles et aux autres dispositions Smernice 1999 5 ES pertinentes de la directive 1999 5 CE Con la presente OvisLink Corp dichiara che i OvisLink Corp vakuuttaa t ten ett WL 5470AP questo WL 5470AP conforme ai requisiti Suomi Finnish tyyppinen laite on direktiivin 1999 5
52. s Client Allow user to set the function Enabled or Disabled 19 WL5470AP User s Manual By the function all wireless clients can t mutual link but wireless client still link with LAN port adapter The default value is Disabled Press the setup button for detail configurations Wireless Security Setup Encryption None WEP WPA PSK TKIP WPA PSK AES WPA2 PSK AES WPA2 PSK Mixed 802 1 RADIUS To provide a certain level of security the IEEE 802 11 standard has defined two types of authentication methods Open System or Shared Key And WL 5470APv2 also support other wireless authentication and encryption methods for enhance your wireless network With Open System authentication a wireless PC can join any network and receive any messages that are not encrypted With Shared Key authentication only those PCs that possess the correct authentication key can join the network By default IEEE 802 11 wireless devices operate in an Open System network and None data encryption If you want secure your wireless network you need to setup wireless security related function to enable security network Encryption Encryption is set to None by default If the Access Point is using Encryption None then the wireless adapter will need to be set to the same authentication mode Wireless Security Setup Encryption PR Apply Changes Reset Encryption If selected WEP encryption you must set WEP key value 20 WL54
53. s Other OvisLink Upgrade Firmware Save Reload Settings Password Log NIP www ovislini com De F Upgrade Firmware Aaa aa a e image Select File as E Unload Reset Upgrade Firmware Upgrade Firmware Select File Browse _Browse Upload Reset 1 Download the latest firmware from your distributor and save the file on the hard drive 2 Start the browser open the configuration page click on Other and click Upgrade Firmware to enter the Upgrade Firmware window 3 Enter the new firmware s path and file name i e C FIRMWARE firmware bin or click the button to find and open the firmware file the browser will display to correct file path 4 Click button to start the upgrade function or button to clear all the settings on this page Save Reload Settings save Reload Settings Save Settings to File Save Load Settings from See File Browse Upload Reset Settings to Default Reset This function enables users to save the current configuration as a file i e config dat or loades configuration from a file Enter the file name or click to find the file from your computer Save Settings to File Click to save the current configuration to file Load Settings From File Click if you want to load a pre saved file enter the file name with the correct path and then click on or click to select the file 49 WL5470AP User s Manual Save in E Desktop D e amp CR ES Look in E Des
54. s points and all devices attempting to connect to a specific WLAN must use the same SSID It is case sensitive and must not exceed 32 characters A device will not be permitted to join the BSS unless it can provide the unique SSID An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network The number of channels supported depends on the region of this Access Point All stations communicating with the Access Point must use the same channel When in Universal Repeater mode you have to enter the ESSID of others AP Router that device want to connect The device SSID and the SSID of extended interface can be the same or different 34 WL5470AP User s Manual When you are using the universal repeater mode please make sure the remote AP Router WDS function is turned off Please refer the Bridge mode settings gt Site Survey for details Please refer the AP mode settings gt Security for details This setting used Wireless client or remote AP to link this device Advance Setting Please refer the AP mode settings gt Advance Setting for details Access Control Please refer the AP mode setting gt Access Control for details 35 WL5470AP User s Manual WISP Client Router Mode Setting CRE Liwe WLAN Access Point i j i Mode Status TCP IP Reboot Other OvisLink i www ovislink com twa A WISP Mode Settings Remote Management setup Alias Name Wir
55. se rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you distribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You must make sure that they too receive or can get the source code And you must show them these terms so they know their rights We protect your rights with two steps 1 copyright the software and 2 offer you this license which gives you legal permission to copy distribute and or modify the software Also for each author s protection and ours we want to make certain that everyone understands that there is no warranty for this free software If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses in effect making the program proprietary To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed at all The precise terms and conditions for copying distribution and modification follow TERMS AND CONDITIONS FOR COPYING DISTRIB
56. show the system log LC Enable Log System all Wireless only Apply Changes 50 WL5470AP User s Manual This function can list all log information about device Enable Log Enabled or Disabled display system log information List system all log information List wireless log information only Refresh log information Clear all information in window NTP Time Zone Setting Current Time Year Month Day Hr Min Sec a0 C Enable NTP client update Time Zone Select GMT 06 00 Taipei se NTP server fs Manual IP Setting This function can setting system time from local computer or Internet Save Save configuration to flash Reset Reset system time configuration Refresh Refresh system time information 51 WL5470AP User s Manual
57. t the Preamble Type should be set to Long Preamble The Short Preamble is intended for applications where minimum overhead and maximum performance is desired If in a noisy network environment the performance will be decreased Select enabled to allow all the wireless stations to detect the SSID of this Access Point IAPP Inter Access Point Protocol is designed for the enforcement of unique association throughout a ESS Extended Service Set and a secure exchange of station s security context between current access point AP and new AP during handoff period 802 119 Protection The 802 11g standard includes a protection mechanism to ensure mixed 802 11b and 802 11g operation If there is no such kind of mechanism exists the two kinds of standards may mutually interfere and decrease network s performance TX Power Level Apply Change For countries that impose limit on WLAN output power it might be necessary to reduce TX transmit power There are 7 TX Power Levels to choose from select a level to make sure that the output power measured at the antenna end will not exceed the legal limit in your country Enable Watch dog Check and enable this watch dog function Watch Interval Setup the interval time for watch dog function between 1 to 60 mins Watch Host Enter the watch dog host ip address ACK Timeout When a packet is sent out from one wireless station to the other it will waits for an Acknowledgement
58. tent infringement or for any other reason not limited to patent issues conditions are imposed on you whether by court order agreement or otherwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is wil
59. tions are different write to the author to ask for permission For software which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 12 INNO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
60. to 20dBm EU 23dBm FCC up to 25dBm South America AP Client Bridge WDS Repeater Universal Repeater mode WISP Client Router WISP Universal Repeater Gateway mode Allows WEP 64 128 bit Support WPA PSK WPA2 PSK encryption Support data rate automatic fallback Automatic channel selection Client access control Supports 802 1x Radius client with EAP TLS TKIP AES encryption Supports IAPP Adjustable Tx power Tx rate and SSID broadcast ACK Timeout Watch dog function Web interface management Support System event log and statistics MAC filtering For wireless only 2 WL5470AP User s Manual Parts Names and Functions 1 Front Panel LED Indicators Power me ea is being applied to this product Green indication WAN port The WAN port is link o Green Blinking activity Wireless Solid The wireless function is ON Green activity Blinking Sending or receiving data via wireless An active station is connected to the corresponding LAN port Link activity Green Blinking Press over 3 seconds to reboot this device Press for over 10 seconds to restore Reset Button factory settings Performing the Factory Reset will erase all previously entered device settings Table 1 LED Indicators 3 WL5470AP User s Manual 2 Rear Panel Connection Ports DC 12V Connects the power adapter plug LAN 1 LAN 2 o Connects inside network group LAN 3 LAN 4 WAN Comnects inside network grou
61. tus TCP IP Reboot Other f werw ovislink com tw bn GW Mode Settings Alias Hame Wireless_AP FT Disable Wireless LAN Interface Band 24 GHz 6 6 E SSID lairlive Channel Number Wireless Client Isolation Security Advanced Settings Access Control Wan Port Virtual Server Special Application DMZ Remote Management Dynamic DNS Ping Dos Setting Diagnostics URL Filtering MAC Filtering IP Filtering eme TA G Al H j Tan GH Ee EE Note You may need to scroll the window in the actual web browser display to view all items in GW Mode Settings Alias Name O Disable Wireless LAN Interface You can set the alias name for this device limited not exceed 32 characters Check the box to disable the Wireless LAN Interface By doing so you won t be able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only O 2 4GHz B G 802 11b supported rate and 802 11g supported rate The default is 2 4GHz B G mode 41 WL5470AP User s Manual The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID In WISP mode you have to enter the
62. ually select the incoming type TCP UDP Incoming start End port Trigger Start End port Select the Trigger Type IT Enable DMZ DMZ Host IP Address Reset Enable DMZ and enter the DMZ Host IP address Remote Management Remote Management Y Enable Web Server Access via WAN Port Number feo Save Reset Enable the function that setting configuration from Internet 38 WL5470AP User s Manual WISP Universal Repeater Mode Setting hi Liwe WLAN Access Point E j Mode Status MPP Reboot Other OvisLink g wwwovislink com twa Site Survey Please refer the Client mode settings gt Site Survey for details Please refer the Universal repeater mode settings gt SSID of extended Interface SSID of extended Interface MAC Clone Address WISP Universal Repeater Mode Settings Alias Name Wireless_AP Disable Wireless LAN Interface Band 2 4 GHz Drais SSID of Extended Interface Clone MAC Address oonooooo0o00 Enable Encryption On Both WAN and WLAN side Security setup Advanced Settings Setup Wan Port Setup Virtual Server setup Special Application setup DMZ Setup Setup Remote Management setup You can set the alias name for this device limited not exceed 32 characters able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You c

AirLive WL-5470AP User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents