Robot Cleaner
Contents
1. Q gt Depending on the model supported languages may vary 32 Language English German French Russian Italian Spanish No 1 2 3 4 5 Maintenance Cleaning the Dust Bin Remove the dust bin J O22 Empty the dust bin bad ge Bes Replace the dust filter Replace the dust bin in the robot cleaner Make sure to follow the directions carefully when installing the dust bin ve gt To clean the dust filter and determine its lifetime see page 34 Replace the dust bin cover 33 Robot Cleaner Cleaning the Dust Filter Me gt The dust filter can be easily cleaned by gently scraping off the surface or compressed air The dust filter is reusable It is recommended not to clean with water gt We recommend that you clean the dust filter whenever the bin is more than 2 3 full If you do not clean the dust filter the suction power of the robot cleaner can be reduced gt Replace the dust filter if you notice a tear or a hole The lifetime of a dust filter is about 3 months for normal use but may vary depending on the frequency and operating environment 1 4 Mesh filter 2 Fine mesh filter 2 Clean the dust filter Remove dust from each of the four filters by blowing Filter cover t 3 Main filter Filter case 4 Pre filter Assemble the dust filter Assemble four filters as described above g2. and damage to the robot cleaner VAN Make sure the power cord is not bent or crushed by heavy objects e A damaged power cord may cause fire or electrical shock e To repair or replace a damaged power cord contact a qualified service agent to ensure your safety When plugging in or removing the power plug always plug it in or remove it by holding the plug not the cable e Stress on the cable will damage the power cord which may cause fire or electrical shock Mwy Do not usea damaged power cord To repair or replace a damaged power cord contact a qualified service agent to ensure safety e If a non qualified person repairs the power cord there is a risk of fire or electrical shock Robot Cleaner Ne VAN Do not touch the plug or wall socket with wet hands Doing so may cause electric shock If you spill water into the robot cleaner unplug the power cord and allow the unit to dry completely before use Water can bring the risk of fire and electrical shock Immediately remove the power cord from the outlet and contact your service center AN Po not use chargers other than the charger that came with your robot cleaner Overvoltage brings the risk of fire and electrical shock AN Do not install the charger in a location that is damp or wet dusty or near water This may cause a fire or an electrical shock and damage to the unit AN Do not touch the terminal of the charger with any metallic object such as a cl
3. Power switch Bottom Signal receiving sensor 9 Cliff detection sensors Charging terminals 11 Wheels 2 Side brush installation pins 3 Dust inlet Main brush 15 Mop plate installation holes Robot Cleaner Control buttons and indicators Charger Front Back 4 Start stop button 2 Power button 3 Cleaning mode selection button 4 Shadow cleaning mode indicator G Turbo mode indicator 6 Auto cleaning mode indicator 7 Timer 1 hour indicator Timer every day indicator 9 Threshold option indicator Double Cleaning option indicator 11 Corner Cleaning option indicator A Charging mode indicator 13 Error indicator Intensive Cleaning mode indicator 15 Battery level indicator 4 Power charging lamp 2 Guide signal transmission sensor 3 Charging terminals 4 Adaptor holder S Adaptor jack 6 Sensor s signal distance selection switch Remote control You can conveniently access the various functions of the robot cleaner with your remote control e Functions that can be controlled through the control panel on the robot cleaner Auto cleaning Shadow cleaning Intensive cleaning Corner cleaning and Charging e Functions that can be controlled through the remote control Auto cleaning Shadow cleaning Intensive cleaning Corner cleaning Double cleaning option Threshold option Manual cleaning Charging Turbo option Reservati
4. 7N 7N in is 4 nite 1HOUR Voice Dust bin is missing AA NAA J 7 Solution Replace the dust bin Cause Both main wheels have been lifted 4 TURBO Voice Please place the cleaner on the floor yN D Solution Put the robot cleaner on the floor or move it to another place Cause Escape rough road mode continually occurred in excess of the limit while e moving N P 7 KZ Voice Please check the front wheel Solution Remove obstacles from the front caster and empty the dust bin Cause Bumper crash continually occurred in excess of the limit while moving oN FA w J 1HOUR Voice Please check the bumper Solution Remove obstacles from the bumper and check if the bumper has been dented Cause The robot cleaner has continually detected the risk of falling more than limitation LX TR FN Voice Please check the bottom sensor WZ DAILY 1HOUR Solution If the color of the floor is black move the robot cleaner to another place Clean or wipe obstacles from the cliff sensors see page 35 Cause Other error ON PN a lf DAILY 1HOUR TURBO Voice There is an error QT X N Solution Contact your customer service 42 Troubleshooting Customer Support Problem Solution The robot cleaner does not work Turn off the power switch on the lower rear side Check the battery Charge the battery in the charger The robot cleaner does not charge Remove any obstacles around the charger Check if the power cord is conn
5. climb over a Except Manual ci ahino mode Press the Threshold Threshold threshold lower than 0 4 inch p g button on the other cleaning modes 1 cm remote control Except Manual cleaning and Press the Double Double Performs 2 cleaning sessions of oe J anng f Scheduled cleaning modes CL button on the cleaning the selected cleaning mode remote control 24 Oy Intensive Cleaning The robot cleaner intensively cleans the surrounding area relative to its current location D e Turn the power switch on YA p 2 3 A r d Y i 4 LJ Li La 1 O C 1 4 sey S ve a ie 7 A Pr as sere gt Ganee ai X adi ae oo Ss Pr d i a F oon Re POPO UON h v Q gt In Intensive cleaning mode the robot cleaner stops on the spot after it has finished the cleaning gt In the area in which there are many obstacles the robot cleaner may not operate in normal cleaning modes 25 Robot Cleaner Shadow Cleaning You can clean under your bed or furniture gt To use shadow cleaning mode turn the room light on In a dark room the robot cleaner can t detect the space under the bed or furniture gt The robot cleaner moves to a place under the bed or furniture to start shadow cleaning To reduce the time spent moving through the room put the robot cleaner in front of the bed or furniture under which you want to perform sh
6. due to intention repair has been paid month after replacement Refund the product at the purchased price Malfunctions in No replacement is available performance and functions during Malfunctions occur three 3 times due to the same Paid repair normal use within Repair is defects the holding period available Malfunctions occur five 5 times due to different 3 F Paid repair of parts defects The repair company has lost the product for which a repair was ja a a lash one requested by the customer produ Refund the product at the fixed purchased price depreciated price after adding 10 of the Repair is NOT available as no parts for repair are in stock within the fixed depreciated amount period in which related parts should be stored Repair is NOT available although parts for repairing are stored Bernd ine product ma the fixed depreciation Replace the product after the amount Replace the product by applying fixed Malfunctions Repair is NOT available corresponding to the expenses for paid depreciation after the expenses for paid repair has been paid or negligence of customers Repairs are available Paid repair Paid repair If you ask for after sales service and the product is not found to be faulty you will be responsible for the service fee Please read through the User Manual before contacting the service center Malfunctions due to customer negligence Malfunctions caused by incorrect power
7. power connection blue lamp e Check the location of the charger Clear all obstacles in the area within 1 m in front left and right of the charger o MS ok ve X gt If you install the robot cleaner in a place where it will be exposed to direct sunlight the heat of the sun may interfere with the auto charging and the robot cleaner may become discolored over time gt If your robot cleaner can t return to the charger reset the detection distance Ina narrow area set it to 5 m and in a wide area set it to 8 m If you set the detection distance to 8 m in a narrow area the auto charging may be interfered with 14 Installing the Side Brushes e Check for the L mark under the side brush e Check for the R mark under the side brush Align with the R mark under the robot cleaner and install the L brush R brush e Align with the L mark under the robot cleaner and install the Robot Cleaner Remote Control Install the battery into the remote control gt Make sure to properly orient the and poles of the batteries when inserting the battery XE gt If you insert batteries incorrectly there is a risk of fire or damage to the remote control Be careful if you use non standard 1 5V batteries as this may cause damage to the product and its function If your battery has had a leakage immediately replace it Dispose of batteries according to
8. the local laws and regulations of your region Inserting batteries into the remote control 1 Remove the battery cover 2 _ Insert the two AAA batteries that came with your robot cleaner 3 Replace the battery cover 16 Installing Charging If you have prepared the charger main body and remote control you must then charge the battery of the robot cleaner to use it To charge the robot cleaner follow these steps 1 e Turn the power switch on 2 e Hold the robot cleaner with both hands and put it on the charger i Match the terminals of the robot cleaner with the terminals of the charger Put the robot cleaner in the front center of the charger and push the robot cleaner toward the charger slowly until the status indicator turns red 3 Use the robot cleaner after charging It takes about 1 hour to charge the battery fully For 2800mAh battery models it takes about 2 hours After charging for 1 hour you can use the robot cleaner in normal suction mode for about 1 hour Depending on conditions the battery usage time may vary Battery status indicator Charging Blinking every second Charging completed On ang comp Low battery Blinking 4 times every second sdz gt You can charge the robot cleaner using connecting the power adaptor directly to the power jack on the lower rear side of the robot cleaner
9. them If the dust bin is full the cleaning performance will be reduced Emptying the dust bin frequently is highly recommended For information on cleaning the dust bin see page 33 If there is anything on cliff detection sensors or wheels remove it This may cause failure or malfunction of the robot cleaner For information on cleaning cliff detection sensors and wheels see page 35 Children and seniors may be surprised at the sight of the robot cleaner in operation Please let children and seniors know about the operation of the robot cleaner Be careful not to drop the robot cleaner from a high place Do not use the robot cleaner on a narrow and a high place such as a desk table etc If shoes are placed side by side at the entrance to the living room the robot cleaner may recognize them as the floor which may cause falling The robot cleaner cannot climb over a threshold higher than 1cm After charging is complete keep the robot cleaner docked in the charger or turn the power switch off which is located on the lower rear side of the robot cleaner 19 Robot Cleaner Starting amp Stopping Cleaning Starting cleaning D e Turn the power switch on 2 a e If you are cleaning an area that is difficult to clean using auto cleaning mode change to the proper cleaning mode Stopping cleaning After cleaning the robot cleaner returns to the charger or stops on the spot according to the cleaning mode I
10. L Inc in the Republic of Korea and or other countries e This publication is protected by copyright and all rights are reserved No part of it may be reproduced or transmitted by any means or in any form without the prior written consent of MONEUAL Depending on the model and type of your appliance some of the contents in this manual may differ from your actual product MONEUAL Inc assumes no responsibility for technical or editorial errors or omissions contained herein nor for any incidental or consequential damages and failures of the appliance caused by not following the precautions and instructions MONEUAL Inc assumes no responsibility for damages resulting from the use of the product that is not approved by the company Robot Cleaner What s in the Box Robot cleaner 1400mA built in battery sie performance 10 Charger Power adaptor Power cord ee SS es Side brushes Cleaning brush Screwdriver for User manual 1 set Side brush ae Nop kits Microfiber Mop Kit 1 Mop plate for a microfiber mop 2 Microfiber mop C Remote control included two AAA batteries Quick start guide gt The appearance and specifications may be changed without notice in order to improve functions or Overview Robot cleaner Top Rear 4 Control buttons and indicators 2 Dust bin cover 3 Bumper 4 Obstacle and signal detection sensors G Air outlet 6 Adaptor jack
11. Micro fiber Mop the ME670 can remove fine dusts Twin Side Brushes Twin side brushes installed on the left and right sides of the bottom completely clean the corners that are difficult to clean with the vacuum suction system alone Eco friendly Lithium Iron Phospate Battery The MONEUAL ME670 uses an eco friendly battery that does not contain any heavy metals or acids that are harmful to the human body The Lithium Iron Phospate Battery has a lifetime that is approximately three times longer 1 000 cycles than standard lithium based or nickel based batteries It provides higher levels of operational safety due to high resistance to heat and explosion Auto Charging After it is finished cleaning or when it detects that the battery is low the robot cleaner auto matically returns to the charger and starts charging Obstacle Avoidance and Fall Protection The obstacle detection sensors in the bumper help the MONEUAL ME670 avoid obstacles and walls and the cliff detection sensors in the bottom detect height differences and prevent it from falling down stairs Contents Before Use Installing Product Operation Features eiin 02 Safety Information eee 05 What s in the BOX eee 10 QOyeryjew ee essre eissis 11 Installing the Charger e 14 Installing the Side Brushes 15 Remote Control eeereeeeeeeserrereereresres 1 6 Charging messenanaciceranin 17 Installing the Mop E A E T 1 8 Before You Start eee eee 1 9 St
12. Robot Cleaner Installing the Mop l 1 Attach the mop to the mop plate 2 lt Turn the power switch off on the lower rear side of 7 the robot cleaner 3 _ Place the robot cleaner upside down on a soft cloth and attach the mop plate Please attach it so that it fits well into the holes of the main body gt If you apply excessive force to the mop plate when you install it on the robot cleaner the joint parts of the mop plate may be damaged 4 _ Flip it over and turn the system power switch on Ge gt After cleaning remove the mop plate from the robot cleaner and the mop from the mop plate gt Wash and dry the mop for its next use 18 Product Operation Before You Start Check the following before you start the robot cleaner Be careful not to break the robot cleaner when you pull the robot cleaner out of the box For information of installing the robot cleaner see page 14 Check the location L R of the brushes and install them For information on installing the brushes see page 15 Pull the robot cleaner out and manually charge it first When you start the robot cleaner for the first time it may not work as the battery has probably been discharged For information on manual charging see page 17 Remove any obstacles on the floor Remove small objects clothes and fragile objects from the floor before cleaning Fold up lengthy carpet rug tassels or keep the robot cleaner away from
13. Ver 1 0 Robot Cleaner User Manual ME670 Series Thank you for purchasing the ME670 series robot cleaner Before using the product please read this User Manual carefully and keep it for future reference Depending on your model some contents of this User Manual may differ from the actual product M oO Ni E l JANI The contents of this User Manual are subject to change without notice Robot Cleaner User Manual ME670 Series MONEUAL Features Shadow Cleaning This is a function that enables you to clean area where the light does not reach In Shadow Cleaning mode you can intensively clean areas under the bed sofa etc that are difficult to clean with a conventional vacuum cleaner High Performance BLDC Motor The cleaning performance is excellent due to the powerful BLDC suction motor The BLDC motor is 30 more powerful than a DC motor and the lifetime is approximately 10 times as long estimated 5 000 hours 8 2 cm Slim Design With a slim design the MONEUAL ME670 is just 8 2 cm high enabling it to clean under the bed and the sofa where it is difficult to clean with a vacuum cleaner or by hand Various Cleaning Modes The various cleaning modes provide different cleaning functions and levels of performance which are optimized for the user environment Auto Cleaning Intensive Cleaning Corner Cleaning Manual Cleaning Scheduled Cleaning Detachable Micro fiber Mop Using Detachable
14. adow cleaning D Turn the power switch on 2 Put the robot cleaner in front of a bed or furniture XPA gt When shadow cleaning is completed the robot cleaner comes out under a furniture and stops 26 Corner Cleaning The robot cleaner runs along the walls of the current place where it is If the robot cleaner takes a turn around the walls or detects the signal of the charger twice it will finish cleaning D Turn the power switch on or vie X gt If the robot cleaner finishes cleaning it will return to the charger 27 Robot Cleaner Manual Cleaning You can control the robot cleaner directly using the remote control 1 Stop the robot cleaner that is operating by pressing the Start stop gt m button 2 e Press the MANUAL button on the remote control E Air suction will start in its current place If you press the MANUAL button again air suction will be stopped ras 3 __ By pressing direction keys on the remote control you can move the robot cleaner where you want it to go Soe gt During charging you can t move the robot cleaner manually gt You can use this mode when you want to move the robot cleaner without air suction 28 Product Operation iyour paty Scheduled Cleaning Reservation Cleaning You can schedule the robot cleaner to start cleaning after 1 hour or at the same time every day 20 gt Before scheduli
15. arting amp Stopping Cleaning 20 How to Recharge the Battery 22 Auto Cleaning E E A E TE 23 Other Cleaning Modes and Options 24 Maintenance Language Setting 32 Cleaning the Dust Bin eee 33 Cleaning the Dust Filter e 34 Cleaning Sensors and Wheels 35 Cleaning the Dust Inlet 36 Using and Managing the Battery 37 Voice Guidance eere 40 Error Message Description 41 Customer Troubleshooting PEIEE IEIET TIE 43 ee een j Product Warranty eee 45 Safety Information Please read and follow the instructions in this manual to ensure your safety and the safe use of your robot cleaner Safety symbols In this manual various Warnings Cautions and Notes are provided to help you to avoid potential hazards that can hurt you and or damage your robot vacuum cleaner You may be killed or seriously injured You may be injured or your appliance A You should refer to this JAN if you do not follow this instruction A may be damaged if you do not follow O note when using your z A this instruction robot cleaner Warning Caution Note Before you use AN Do not install or use the robot cleaner in a place where it will be exposed to direct sunlight If the power adapter becomes overheated during charging it may cause a fire short circuit or electrical shock The robot cleaner may become discolored and deformed AN Do not install the charger on an inclined floor and do not apply impact to the charger The charger
16. capacity Malfunctions caused from external shock or fall Malfunctions due to the use of consumables or optional devices not specified by our company Cases when the product is not faulty Users asking for warranty service before fully understanding the User Manual Problems in external environment including propagation of radio waves and wired signals m Errors in initial installation for the supplied product Treatment of filtering and removal of foreign substances from accessories Malfunctions caused by repair person who is not from the partner Malfunctions caused by other companies products including software companies specified by our company Malfunctions caused by ignorance of the Safety Information described in the User Manual Other cases Malfunctions caused by natural disasters lightning fire salt damage and water damage The life of consumables has expired A S info moneual eu www moneual eu MONEUAL Customer Service info moneual eu Before you call for service please be ready to provide the following information Model name A description of your problem Phone no amp address MONEUAL www moneual eu
17. e battery lifetime may vary depending on the use environment Charging battery e If you are using the robot cleaner for the first time please fully charge the battery first e It takes about 1 hour to charge the battery fully For 2800mAh battery models it takes about 2 hours To extend battery life lt If you don t intend to use the robot cleaner for an extended period of time turn off the power switch after charging the battery fully e Clean the dust inlet dust bin main brush and side brushes frequently If you use the robot cleaner with the dust bin full the rotation of the internal motor will be increased which may shorten the battery lifetime Always use the robot cleaner after charging e Do not use the robot cleaner in a place where it will be exposed to direct sunlight or near the heating source 37 Robot Cleaner Battery replacement lt If you notice that the operating time has been significantly reduced you may need to replace the battery You must use a battery that is manufactured by Moneual Remove the battery from the robot cleaner when the system power is off Dispose of your old batteries according to the local laws and regulations of your region To purchase an extra battery please contact our customer service e If itis difficult to replace the battery by yourself please contact our customer service Remove four screws and remove the battery cover 1 Disconnect the battery cabl
18. e connector and remove the battery Press and hold the lock clip to disconnect the battery cable connector 38 Maintenance Install the new battery and connect the battery Replace the battery cover and cable connector tighten with four screws Battery handling and safety information e If you leave the fully discharged battery for a long time the battery may become damaged and you may not be able to use it If you use a battery other than Moneual s for use with the robot cleaner the robot cleaner or the battery may be damaged e Remove the battery before disposing of the robot cleaner 39 Robot Cleaner Voice Guidance Following voices are the basic voice list Depending on your model some contents of these voices may differ from the actual voices Voice Guidance Starting automatic cleaning The robot cleaner will start auto cleaning Starting corner cleaning The robot cleaner will start corner cleaning Starting intensive cleaning The robot cleaner will start intensive cleaning Starting pre set cleaning The robot cleaner will start the scheduled cleaning Starting shadow Cleaning The robot cleaner will start shadow cleaning Cleaning is completed The cleaning is completed Cleaning is cancelled When you press the Start Stop gt I button during operating Moving toward the charger When you press the CHARGE button or the robot cleaner
19. ected to the charger Turn on the power switch at the rear of the charger If you charge the robot cleaner affectedly it may not be charged The remote control does not work Replace the batteries Suction power is weak Clear the dust bin Clear the filter of the dust bin Check if there is any obstacle in the dust inlet The power is not turned on Turn off the power switch on the lower rear side Check the battery The brush does not rotate Check if there is any obstacle in the brush Check if the brush has been installed properly The operational noise is louder than normal Check if the dust filter is installed properly Check if there is any obstacle in the brush The robot cleaner action is not working normally during cleaning Check if the mop plate is installed properly Clean the sensor with a soft cloth The scheduled cleaning does not work Press the SELECT button to confirm the time setting The robot cleaner does not respond if you press the button When you are charging the robot cleaner by connecting the power adaptor directly the buttons will not be recognized This is normal The operating time is short If you do not properly connect the robot cleaner to the charger or the adaptor for a long time the battery may be discharged In this case the battery usage time may be short Do not disconnect the charger even if the c
20. eight 66g Battery AAA size x2 Signal Transmission Distance IR 5 m 44 Product Warranty The warranty service we provide to our consumers is based on the customer compensation regulation If you request warranty service MONEUAL will provide the service The company will notify the customer of whether he or she will be compensated and the details of the compensation within seven 7 business days after the day of the customer s request and offer the compensation within fourteen 14 business days after the day of notification We do not offer any paid free service for parallel imports The warranty Product Name period for the Model Name Purchased Date Month Date Year gee a Serial No Dealer warranty for the Price battery is six 6 months Free ice If products for general users are used for commercial purposes free service may not be offered Compensation details Type of damages to customers Within the warranty period After the warranty period Replace the product with a new one or Essential repair is required within ten 10 days after the purchase refund the product at the purchased price Replace the product with a new one or Essential repair is required within one 1 month after the purchase offer frea service Not applicable A replaced product is faulty requiring essential repair within one 1
21. elow please contact your customer service gt The error voice guidance comes only one time when the error has occurred You can re check the error status by pressing the SELECT button on the remote control when the power is off Cause The battery is fully discharged so the robot cleaner does not work CS A DAILY Voice Out of battery kaa g Solution Charge the robot cleaner manually Cause The wheel motor has been overloaded Some obstacles hairs wires etc are CICS jammed on one or both wheels a Ba Dally ed 1o Pi Voice Please check the wheels Solution Move the robot cleaner to another place Remove obstacles on the wheel s Cause The dust inlet fan is overloaded A wie TURBO Voice There is an error Solution Remove obstacles in the dust inlet and empty the dust bin Cause The main brush is overloaded A Tie TURBO gaily Voice Please check the main brush Solution Remove obstacles hairs wires etc in the main brush Cause You tried to charge the robot cleaner without the battery any DAILY Voice No Battery y oN Solution Check if the battery is installed in the robot cleaner properly Cause The battery failure 7N 1HOUR Voice There is an error y N 4 Solution Contact your customer service 41 Robot Cleaner Cause You operated the robot cleaner without the dust bin
22. f you press the Start stop W button when the robot cleaner is operating the cleaning will be stopped 20 Product Operation Changing the cleaning mode User can set the cleaning mode to match the cleaning environment e Cleaning modes that you can select using the Mode M button on the robot cleaner Auto Shadow Intensive Corner Cleaning Cleaning Cleaning Cleaning e Cleaning modes that you can select using the remote control Auto Shadow Intensive Corner Manual Scheduled Cleaning Cleaning Cleaning Cleaning Cleaning Cleaning ve XA gt You can t change the cleaning mode during operation Select the cleaning mode before starting the robot cleaner or select it after stopping the robot cleaner by pressing the Start stop gt E button on the robot cleaner or the remote control then selecting the cleaning mode 21 How to Recharge the Battery Auto charging e When the robot cleaner has finished cleaning it returns to the charger lt If the battery is low and the battery indicator is blinking rapidly the robot cleaner will stop cleaning and return to the charger to charge Manual charging e Hold the robot cleaner with both hands and put it on the charger e Match the terminals of the robot cleaner with the terminals of the charger Put the robot cleaner in the front center of the charger and push the robot cleaner toward the charger slowly until the status ind
23. harge is completed If you do not intend to use the robot cleaner for an extended period of time turn off the power switch on the lower rear side can t control the suction power If the mop plate is attached to the robot cleaner you can t control the suction power Clean the mop plate installation holes 43 Robot Cleaner Specifications Robot cleaner Model ME670 Dimensions 348 mm Diameter x 82 mm Height Weight 2 674 kg Speed Cleaning mode 32 cm sec Driving mode 30 cm sec Operating noise Max 68 dB 1400 mAh battery Max 70 dB 2800 mAh battery Power consumption Max 20 W 1400 mAh battery Max 25 W 2800 mAh battery Battery Lithium iron phosphate LiFePO4 12 8V DC Dust bin capacity 600 ml Charging time About 60 minutes 1400 mAh battery Max 120 minutes 2800 mAh battery Operating time About 60 minutes normal vacuuming and 1400 mAh battery About 40 minutes turbo vacuuming and 1400 mAh battery About 120 minutes normal vacuuming and 2800 mAh battery About 80 minutes turbo vacuuming and 2800 mAh battery Charger Model MRD6500 Dimensions 264 mm W x 179 mm H x 134 mm D Weight 606 g Input Power 18V DC Output Power 18V DC Signal Transmission Distance IR 5m 8m Remote control Model MRC6500 Dimensions 139 mm W x 22 mm H x 50 mm D W
24. icator turns to red oo gt You can charge the robot cleaner using connecting the power adaptor directly to the power jack on the lower rear side of the robot cleaner Battery status indicator e You can check the battery status by the battery status indicator Battery status indicator Battery status _ Blinking 4 times every second Need to charge m Low 2 hours It takes about 1 hour to charge the battery fully For 2800mAh battery models it takes about m Middle High or fully charged _ Blinking 1 time every second Charging 22 After charging for 1 hour you can use the robot cleaner in normal suction mode for about 1 hour Depending on conditions the battery usage time may vary Product Operation Auto Cleaning It is the normal cleaning mode The robot cleaner cleans all spaces are open 1 Turn the power switch on 12 shie Xj gt After cleaning the robot cleaner returns to the charger gt If you press the Start stop gt button when the robot cleaner is operating the cleaning will be stopped If you press the Start stop gt button when the robot cleaner stops it will start the cleaning again In this case the selected cleaning mode is ignored and the robot cleaner starts a new auto cleaning session gt If the mop plate is installed on the robot cleaner it cleans with suction and mop cleaning modes gt While in Au
25. ip pin etc This creates the risk of fire and electrical shock If you do not plan to use the robot cleaner for an extended period of time turn off the power switch at the bottom of the back The battery may be discharged if you leave it switched on To ensure safety only a qualified service agent should repair or disassemble the product Repair by unqualified personnel may damage the robot cleaner and brings the risk of fire and electrical shock Dispose of the battery properly If you throw the battery into fire or expose it to direct sunlight there is the risk of fire and explosion Dispose of your old batteries according to the local laws and regulations of your region Clean the obstacle and bottom sensors periodically If the sensor becomes covered by lint and dust the robot cleaner may malfunction Please use the specified filter Use of a different filter will void your warranty Please clean the robot cleaner after turning it off If you clean it when the power is on or it is operating it may cause injury Clean the main brush dust bin dust filter and dust inlet periodically If you use the robot cleaner for a long time without cleaning it there is the risk of malfunction and damage Copyright and instructions e Copyright 2014 MONEUAL Inc All rights reserved e Published March 5 2014 MONEUAL MONCASO MiNEW RYDIS and SONAMU are the trademarks or registered trademarks of MONEUA
26. is moving to the charger for auto charging Starting to charge The charger will start the charging process Starting scheduled cleaning after 1 hour The time setting is completed for 1 hour later cleaning Setting daily cleaning The time setting is completed for every day cleaning Moving to shadowed area When starting a shadow cleaning the robot cleaning moves to the shadowed area Starting a Double cleaning When you select the double cleaning option and start secondary cleaning voice guidance Maintenance Messages Out of battery The battery has been discharged Dust Bin is missing The dust bin has been removed Please place the cleaner on the floor The robot cleaner has been lifted from the floor Please check the wheels The wheels are jammed Please check the main brush The main brush is jammed with hairs or other obstacles Please check the side brush The side brushes are jammed with hairs or obstacles There is an error An error has occurred refer to the error code 40 Maintenance Error Message Description se gt The cleaner will display combination of numbers and icons to inform users of what the issue is Using the information below it is important to resolve the issue first as pressing any button will clear the error message gt If the problem has not been solved with one of the solutions b
27. less than a 1cm threshold height of threshold or carpet rug and etc the user is able to choose Threshold climbing over ON OFF option by the remote control QE gt We also recommend that you select the Threshold Option climb over ON while in Vacuum Cleaning mode gt Factory default is set to not climb over gt Threshold option is not available in Manual Cleaning mode THRESHOLD or Power on Climbing over Threshold Power off Not climbing over Threshold 30 Product Operation C2 Double Cleaning Option The Double Cleaning Option performs 2 cleaning sessions of a selected cleaning mode Press the Double CL button on the remote control to choose a Double Cleaning option X gt Double Cleaning Option is not available in Manual Cleaning mode and Scheduled Cleaning mode viy DOUBLE CL 31 Language Setting l A J 5 3 X gt You can select a language for voice guidance from the ones available in the system Press and hold the Mode button and then turn the power switch on y Keep pressing the Start Stop button until you have reached the language you desire Whenever you press the Start Stop button you will hear the following sentence as a different language Starting automatic cleaning Cleaning is canceled After hearing the language you desire press the power button to complete the language setting
28. may become damaged or broken AN Do not use the product in a room with an unattended child or an elderly person There is a risk that the child or elderly person may become frightened or injured This robot cleaner is not intended for use by children or by persons with reduced physical sensory or mental capabilities unless they have given supervision or instruction concerning the use of the robot cleaner by a person responsible for their safety This may cause injury or damage the robot cleaner Before you use the robot cleaner remove any small objects clothes and fragile objects from the floor to be cleaned This may cause damage to the robot cleaner and obstruct the movement of the robot cleaner Make sure to remove fragile objects glass china flowerpot etc Small cloths power cords belts towels pads and telephone cords can become entangled in the wheels or brushes Remove obstacles on the floor before cleaning The robot cleaner will not be able to move beyond obstacles of a certain height Robot Cleaner ae h Install the charger in a location that can be easily accessed by the robot cleaner If you install the charger in a corner or if there are many obstacles around the charger it may prevent the robot cleaner from automatically charging 4 Make sure that the charger is always plugged into a power source If no power is supplied to the charger you will not be able to use the aut
29. may cause damage to bumper sensors and malfunction Do not use the robot cleaner in a place where the temperature is too low or too high lower than 5 C and higher than 35 C ej e This may cause damage to the product Do not use the robot cleaner when the dust bin is completely filled up j e This may reduce the suction power Never use the robot cleaner without the filters 6 e Doing so may cause a malfunction of the robot cleaner Remove objects such as loose clothing towels cloths belts or hairs scattered on the floor before cleaning Keep objects away from brushes and wheels to prevent entanglement e This may cause noise reduce the suction power and damage the robot cleaner Do not use the robot cleaner in a place where the floor or wall is made of glass or mirrors e The robot cleaner detect obstacles by using an IR sensor so it may not detect glass and mirrors as obstacle N Do not use the robot cleaner in a utility room on a wet floor on stairs on a table or shelf in an underground room in a warehouse in a commercial building or outdoors pi N If you have dropped or given an impact to the robot cleaner contact your service center Electrical instructions Please use the power source and socket with the correct voltage and current e If you use a power source or socket that does not fit the power specifications there is the risk of fire electrical shock
30. ng you must install the charger You can only set the cleaning schedule using your remote control If the robot cleaner is charging at the scheduled time it will start the cleaning after finishing the charging gt If the cleaning time is scheduled to 1 hour the schedule setting will be initialized after completing the scheduled cleaning at the scheduled time gt If the robot cleaner is operating set the time after stopping the robot cleaner by pressing the Start stop gt M button 1 Select the time 1 hour or every day by pressing the RESERVATION button on the remote control RESERVATION Each time you press the RESERVATION button the 1 hour or every day lamp will turn on and off in sequence If all lamps are turned off it means the time is not set MONEUAL 2 Press the SELECT button to apply the setting 3 The robot cleaner moves to the charger and will start auto cleaning at the scheduled time If there is no charger nearby the robot cleaner will not move to the charger If you set it to every day the robot cleaner will start the cleaning at the same time based on the scheduled time vie Xj gt Double Cleaning option is not available in Scheduled Cleaning mode 29 Robot Cleaner r Re0 Turbo Option By pressing TURBO button on the remote controller you can control Suction power Power off Power on Threshold Option For
31. omatic charge function AN Do not use the power adaptor with another appliance This may cause damage to the appliance and fire by overheating Ensure that clothes or any part of the body hair finger foot etc do not get entangled in the brushes or wheels This may cause injury Do not use or store the robot cleaner near flammable materials alcohol gasoline kerosene thinner etc or heating sources cigarettes candles stove etc This may cause fire and damage to the robot cleaner If you notice smoke or a burning smell coming from the robot cleaner immediately turn the power switch off and contact your service center A Do not stand or sit on the robot cleaner Movement of the robot cleaner may cause injury or the robot cleaner may be damaged Do not use the robot cleaner on a narrow high place such as a desk table etc The robot cleaner may fall off which could cause injury or damage to the product Do not let the robot cleaner pass over or sweep up liquids oil pet droppings etc This may cause malfunction of the robot cleaner and damage Liquid on the wheels may cause stains in other places If the robot cleaner sucks a plastic bag in while operating immediately remove it If you run the robot cleaner for a long time with the dust inlet covered with a plastic bag the motor will be overheated and the robot cleaner will be damaged Do not press strongly or impact the bumper This
32. on cleaning Mute and Manual moving 4 Power button lt Press to turn the power on off Press to return the robot cleaner to operation mode when it has stopped due to failure 2 Mode button Press to select the cleaning mode 3 Start Stop button e Press to start the selected operation e Press to start stop cleaning and driving 4 Select Manual button e Press to confirm your selection e Press to start manual cleaning see page 28 CHARGE CORNER 5 Direction buttons Press to drive the robot cleaner in manual mode INTENSIVE forward backward left and right oo 6 Charge button Press to move robot cleaner to charger T Intensive cleaning button Press to start intensive cleaning see page 25 Corner cleaning button Press to start corner cleaning see page 27 MONEUAL 9 Turbo button Press to select Turbo option see page 30 Shadow cleaning button Press to start under furniture cleaning see page 26 1 Double cleaning button Press to select Double cleaning option see page 31 2 Reservation button Press to set the timer see page 29 13 Mute button Press to turn voice guidance on off Threshold option button Press to select Threshold option see page 30 13 Robot Cleaner Installing the Charger e Connect the power adaptor Set the robot cleaner detection distance 5 m or 8 m e Place the power adaptor in the holder of the charger Check the
33. t Applying excessive force will damage the dust filter cover while disassembling the dust filter gt If you assemble the filter incorrectly the performance may be degraded or the suction power may be reduced 34 Maintenance Cleaning Sensors and Wheels Cleaning sensors e Clean blow or wipe the three sensors with the included clean ing brush or a cotton swab If sensors are severely contaminated wipe with a moistened cotton swab Do not wipe directly with water and do not use benzene or alcohol to clean sensors Cleaning wheels e Clean wheels using the brush To clean the front wheel and two main wheels clean them with the brush while rotating slightly by hand Remove foreign objects such as hair that obstruct the wheel s operation 35 Robot Cleaner Cleaning the Dust Inlet Remove the main brush Check the groove s shape and insert the main brush into the fixing hole and then secure the wing of the fixing pin to the fixing pin Clean the removed main brush with the cleaning brush To reinstall the dust inlet cover insert the 2 tips to the matching holes on the robot cleaner 36 Maintenance Using and Managing the Battery The battery is a consumable item The more you use the battery the shorter the battery s lifetime Battery lifetime We guarantee 6 months of use in a normal environment Always charge the battery for the best use experience e Th
34. to Cleaning mode you can also select Double Cleaning Option and Threshold climb over Option To select these options please refer to the pages that reference each 23 e Robot Cleaner Other Cleaning Modes and Options other cleaning modes Cleaning Mode Function For Where How to Select Select Intensive with the Mode Heavy Dust A Clean in 1m x 1m area where button on the Control Panel or press Intensive Particles or Heavy F the robot cleaner located the Intensive button on the remote Traffic Area control Select Shadow with the Mode shadow Clean in the hard to reach Under a bed or button on the Control Panel or areas furniture press the Shadow button on the remote control The robot cleaner runs along Anywhere you Press Corner cleaning button on Corner the walls of the current place ae want to go the remote control where it is Control the robot vacuum Press the Manual button on the Anywhere you Manual cleaner directly using the Ne nenaae remote control and press the Arrow remote control g button where you want to go l Start cleaning after 1 hour or Anywhere you Press the Reservation button and Reservation press the Select button on the at the same time every day want to go remote control Option Function Applicable cleaning mode How to Select Start cleaning with turbo i Press the Turbo Turbo All cleaning modes button on the suction power remote control Set to be able to
Download Pdf Manuals
Related Search