RFID Reader - Digital Eye Brand
Contents
1. NG Switch 1 and 2 of SW are set to ON by default Before you change the output format you must disconnected the power English 11 NOILVZITVILINI intialization BASIC OPERATIONS Initial State when the power is supplied When you apply power to the product it will sound beep three times before entering Standby with the red indicator turned on Using the card Present the card to the product until you hear a beep and the green indicator turns on maa The reader keeps the green indicator turned on while transferring the card data to the Zz mG controller When it is done the green indicator turns off and for receiving the next card oz the red indicator stays ON Using the keypad Hold down the keypad until you hear a beep The reader transfers the keypad data to the controller If the output format of the keypad is 26 bit Wiegand pressing any key of the keypad turns on orange indicator and green indicator blinks when ENT is pressed after the input The red indicator stays on after transferring data to the controller By default it is 8 bit burst Hence keypad input and pressing ENT will blink the green indicator only when you change the option to 26bit Wiegand LED Control You can control the red green and orange indicators as necessary To control the red indicator connect the red indicator control input line white with red stripes to the relay output NO port of the controller a2. 0 x 109 0 x 31 0 Weight 160g Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical
3. and extemal connection INSTALLATION 1 Attach the provided wall mount to the wall and drill two 6 32 holes and one 1 2 inch hole on it See Figure 1 Refer to Figure 2 below on how to secure the wall mount to the wall using the provided screws o N Apply each of 5 O rings to the corresponding point as shown in Figure 2 4 Fix the main unit with the wall mount by inserting the main unit s cables into the center hole and pushing the main unit towards the wall mount 6 32 hole MAS w O myo O ring O ring E E 1 2 hole ig 3 E E E O ring amp tO O ring 6 32 hol 2 5 o g 0 BOT 1 52 38 5mm 1 52 38 5mm 3 03 77mm Figure 1 Figure 2 DB Once the main unit is fixed with the wall mount it will not be loosened Please check if the device is operating properly before fixing it If you try to remove the wall mount once it is fixed the lock parts of the wall mount will break resulting in a situation where the whole wall mount must be replaced 8 installation and external connection PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL If you install the reader on a metal wall the read range may be reduced To avoid this problem it is recommended to insert the spacer between the metal wall and the reader as shown below Spacer Reader IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK If you install more than o
4. symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system English _ 17 SALES NETWORK SAMSUNG TECHWIN CO LTD 701 Sampyong dong Bundang gu Seongnam si Gyeonggi do Korea 463 400 TEL 82 70 7147 8740 60 FAX 82 31 8018 3745 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Tol Free 1 877 213 1222 FAX 1 310 632 2195 Park Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungsecurity com www samsungtechwin com P No Z8100239101A
5. 2 8 1000 8 3 0011 3 9 1001 9 4 0100 4 ESC 1010 A 5 0101 5 ENT 1011 B 8Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 11110000 FO 6 10010110 96 il 1110000 E1 U 1000011 87 2 11010010 D2 8 01111000 78 3 1100001 C3 9 0110100 69 4 10110100 B4 ESC 01011010 5A 5 1010010 A5 ENT 0100101 4B English 15 1VNH04 LNdLNO troubleshooting TROUBLESHOOTING If the product does not function properly please see the below for trouble shooting SOLUTION PROBLEM My card is not read properly Check the rated voltage specified in the user manual and the catalog Ensure that the card must comply with the PSK 125KH2 format provided by Samsung Cards of 13 56MHz format can not be used Contact the card retailer regarding the card format If the problem persists contact the nearest customer service for your assistance When I turn on the product it sounds a beep with dimly turned on indicator Ensure that you are using a larger capacity adaptor than specified in the user manual or the catalog which should cover the rated current consumption of the reader If you are using multiple readers that are connected to one adaptor make sure that the adaptor should be large enough to cover the current consumption multiplied by the reader count Even with a large adaptor enough to supply adequate power if the power cable is not a dedicated l
6. SSA R2000 REIL Reader user manual imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please visit our website www samsungsecurity com safety information RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit important operating and maintenance servicing instructions in the literature This exclamation point symbol is intended to alert the user to the presence of accompanying the appliance WARNING e To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture WARNING 1 Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product 2 Incorrectly connecting the power supply or replacing battery may cause explosion fire electric shock or damage to he product Do not connect multiple controllers to a single adapter Exceeding the capacity may cause abnormal heat generation or fire Securely plug the power cord into the power receptacle Insecure connection may cause fire When installing the controller fasten it securely and firmly T
7. connect the yellow line to the controller s output relay Connect the blue with white stripes to control the orange indicator connect the white with red stripes to control the red indicator see page 12 Buzzer Control Enables you to turn on or off the buzzer To control the buzzer connect the blue line to the controller s output relay see page 12 am en Cono Connect the COM port gray line of the product s tamper switch to GND connect the NC port green with p white stripe of the tamper switch to the input port of the controller Connect to the COM port of the PC Connect pin 2 of the DB 9 connector to the purple line connect the aaa black line of the 6 pin connector to pin 5 of the DB 9 connector 10 installation and external connection Intalization OUTPUT FORMAT You can adjust the output format of the numeric values from the keypad You can select 4 8 bit Burst or 26bit Wiegand Adjust the format according to the controller receiving the keypad input 1 To change the output format use the switch on the rear of the product ON 1 2 2 See the table below to make adjustment as needed Output Format SW 1 SW 2 Output Format of Card Output Format of Keypad ON ON 26bit Wiegand RS 232 8bit Burst Default ON OFF 26bit Wiegand RS 232 26bit Wiegand RS 232 OFF ON 26bit Wiegand RS 232 26bit Wiegand RS 232 OFF OFF 26bit Wiegand RS 232 4bit Burst
8. ct is an elegant looking proximity reader equipped with the built in keypad which has the maximum of 10 cm 4 read range It is also supported by backlighting on the keypad enabling stable operation at night This product permits user access through authentication of the presented proximity card and personal identification number using the keypad Red green and orange LED indicators and the Piezo buzzer ensure reliable and accurate operation 125 KHz Proximity PIN Reader PSK Modulation 26 bit Wiegand RS 232 Data Output 4 8 Bit Burst Output Format supported Numeric Keypad with Backlighting for Night Operation 8 Control of External LED Indicators Control of External Buzzer Tamper Switch Reverse Polarity Protection WHAT S INCLUDED Check if the following items are included in the product package Product Wall Mount O ring x5 aso ay CABLE 3 5 x 40mm Screws x4 3 5 x 12mm Screws x4 ta Satb i i CD Manual 6 x 30mm Plastic Anchor x4 PIN Connector X 1 Quick Guide Quick Guide English 5 NOILONGOHINI LONGOdd product Introduction AT A GLANCE Front Rear SAMSUNG 1 LED Displays the status of the system operation 2 Keypad Used to enter the ID password 3 2 PIN Connector Can be connected to the power cable 4 6 PIN Connector Can be connected to Wiegand RS 232 communication cables 5 8 PIN Conn
9. ector Connected to the tamper LED and buzzer control connection cables 6 Output Selection Switch Switch that allows you to select an output from 8 bit 4 bit Burst and Wiegand 7 Tamper Switch Tamper switch 8 Fixing Screw Screws for fixing the devices 6 product introduction CABLE COLOR SCHEME 2 PIN Connector 1 O Pins Signal Cable Color Power 412V DC 412V Red Earth grounding GND Black 6 PIN Connector 1 O Pins Signal Cable Color Wiegand Data Output 0 WIK DATAO Green Wiegand Data Output 1 WIK_DATA1 White Not Used Not Used Orange RS 232 TX TX OUT Purple Not Used Not Used Brown RS 232 GND GND Black 8 PIN Connector 1 O Pins Signal Cable Color Tamper Switch NC Tamper NC Green with White Stripes Tamper Switch COM Tamper COM Gray LED Control Red LED Control White with Red Stripes LED Control Green LED Control Yellow LED Control Orange LED Control Blue with White Stripes Buzzer Control BUZZER Control Blue Not Used Not Used Pink Not Used Not Used Sky Blue CABLE SELECTION Item Cable Type 4 Power octay Belden 9409 18 AWG 2 Conductor Unshielded Card PIN data Wiegand Belden 9512 22 AWG 4 Conductor Shielded 2 Control signal LED BUZZER TAMPER Belden 9514 22 AWG 8 Conductor Shielded 3 Bs 2320able Belden 9829 24 AWG 2 twiste pair Shielded English _ 7 NOILONGOHINI LONGOdd installation
10. eplacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus 1 CO Unplug this apparatus when a card is used Use caution when moving the cart apparatus JAN combination to avoid injury from tip over 1 P Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped English _ 3 NOILVINYOANI ALSAVS contents PRODUCT INTRODUCTION INSTALLATION AND EXTERNAL CONNECTION INITIALIZATION OUTPUT FORMAT TROUBLE SHOOTING PRODUCT SPECIFICATION 4 contents NNO OO O Oo 11 13 15 16 17 Features What s included At a Glance Cable Color Scheme Cable Selection Installation Precautions on installation External Connection Output Format Basic Operations WIEGAND Output RS 232 Output 4 8 BIT BURST Output Format Trouble Shooting Product Specification oroduct Introduction FEATURES This produ
11. he fall of controller may cause personal injury aap w Do not place conductive objects e g screwdrivers coins metal parts etc or containers filled with water on top of the controller Doing so may cause personal injury due to fire electric shock or falling objects N Do not install the unit in humid dusty or sooty locations Doing so may cause fire or electric shock 8 If any unusual smells or smoke come from the unit stop using the product In such case immediately disconnect the power source and contact the service center Continued use in such a condition may cause fire or electric shock 9 If this product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair 10 When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock CAUTION 1 Do not drop objects on the product or apply strong blows to it Keep away from a location subject to excessive vibration or magnetic interference 2 Do not install in a location subject to high temperature over 50 C low temperature below 30 C or high humidity Doing so may cause fire or electric shock 3 If you want to relocate the already installed product be sure to turn off the power and then move or reinstall it 4 Remove the power plug from the outlet when there
12. ine such as communication line or UPT cable or if it s so long to cause power loss you d better replace it with a dedicated line or reinforce it If the problem persists contact the nearest customer service for your assistance The read range R R of the card differs each time the product reads the card The characteristics of a card are determined by the nature of the coils used and in the manufacturing process engaged by the card manufacturer So what you do first is to check that the cards in use are made by the same manufacturer If you are using cards from different card makers the read range R R differs by the card which is the result of normal operation If you encounter a different read range for each card that is made by the same manufacturer please contact the nearest customer service 16_ troubleshooting oroduct specifications PRODUCT SPECIFICATIONS Item SSA R2000 Power Current DC 12V Max 95mA Reading Time Card 30ms Input Port 2 ea External LED Control Extemal Buzzer Control Output Port 26bit Wiegand 4 8bit Burst for PIN Selectable LED Indicator 3 LED Indicators Red Green and Orange Beeper Piezo Buzzer Keypad 12 Key Numeric Keypad with Back Lighting Operating Temperature 30 C to 50 C Operating Humidity 10 to 90 Relative Humidity Non Condensing Color Material Silver with Black Polycarbonate Dimension W x H x D mm 87
13. is a lighting storm Neglecting to do so may cause fire or damage 0 the product 5 Keep out of direct sunlight and heat radiation sources It may cause fire 6 Install it in a place with good ventilation 2 safety information 7 Avoid aiming the controller directly towards extremely bright objects such as sun 8 Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 9 The Mains plug is used as a disconnect device and shall stay readily operable at any time FCC Statement Caution Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions any cause harmf
14. nd connect the GND line to the COM line Set I O of the controller now you can control turning on off the indicators You can turn on off the indicators according to the I O settings of the controller which can be applied to various situations For more information about the I O settings of the controller refer to the user manual of the controller Connect the yellow line for the green indicator or the blue with white stripes for the orange indicator to the COM port of the controller Buzzer Control Connect the buzzer control input line blue to the NO port of the controller relay output and GND to the COM port You can configure the I O settings of the controller so that it beeps If the product continues to beep it means that the buzzer control is working properly The controller can use the I O settings to set the buzzer control so that it sounds an additional beep for authorized or unauthorized access upon user authentication Furthermore you can make various modifications according to the different I O settings of the controller For more information about the I O settings of the controller refer to the user manual of the controller Card reading is not available while the buzzer control is sounding the buzzer Tamper Control You can set the signal that you want to output if the device is dismantled forcibly Connect the COM port gray line of the product s tamper switch to GND connect the NC port green with white
15. ne reader side by side or front and back the read range may be reduced In this case if you present a card to one reader the other reader may recognize the same card meaning both readers read the same card simultaneously To avoid this problem keep at least 20 cm of space between the two readers Minimum 20cm set got wet eet a Reader 2 Reader 1 lt Front and Back gt Reader 1 Minimum 20cm sans PIL Reader 2 lt Side by Side gt English _ 9 NOILOANNOO TVN431X3 ANY NOLLVTIVLSNI installation and extemal connection EXTERNAL CONNECTION WIRING DIAGRAM SSA R2000 Wiegand Data 0 Out Green maa Wiegand Data 1 Out White Tamper Switch Out NG Groen with white stripes ree Tamper Switch Out COM Gray TE we Purple CONTROLLER PC Buzzer Control In Blue 7 ki ns 522GND LED Control In Red White with red stripes 3 3 Black amp 6 amp LED Control In Green Yellow LED Control In Orange Blue with white stripes ere POWER Category Cable Color Connect the DC 12V to the red line Power Supply Unit Connect GND to the black line Connect the green line of the product to the Wiegand DO input port of the controller Wiegand Connection Connect the white line of the product to the Wiegand D1 input port of the controller Enables you to turn on or off the LED indicators LED Control To control green indicator
16. stripe of the tamper switch to the input port of the controller If the tamper of the reader operates the controller produces an input signal and generates the corresponding output depending on the controller setting 12_ initialization output format WIEGAND OUTPUT Timing Diagram 100us He HE 5V DATA 0 mg 0V 5V DATA 1 a ET ov 1 2 3 n 2 n 1 n n 34or26 LOGIC 0 1 1 1 0 0 Data Type 26 bit e Bit 1 Even Parity bit 2 bit 13 e Bit 2 9 Facility Code 000 255 e Bit 10 25 ID Number 00000 65 535 e Bit 26 Odd Parity bit 14 bit 25 English 13 1VINH04 LNdLNO output format RS 232 OUTPUT Output Waveform LSB MSB 15V 0 1 0 0 0 0 0 1 0 Space 0 mE NG KA NN a ov eee ON GR al ee eee IR ee ee E Mark 1 IBV i lt _ 8 Data Bits gt i I 2 Stop Bits Start Bit it Data packet corresponding to ASCII character A gt Data Type START 0X02H DATA 8 Char END 0x03H LRC START 0X02H DATA 1 8 Char END Ox03H LRC Check the following settings Baud Rate 9600bps Data Bit 8 Parity Bit None Stop Bit 1 LRC This is the result of XOR operation of each byte from Start to End 14_ output format 4 8 BIT BURST OUTPUT FORMAT 4Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 0000 0 6 0110 6 1 0001 1 7 0111 T 2 0010
17. ul interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions NGO ONE Do not install near any heat sources such as radiators heat registers or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for r
Download Pdf Manuals
Related Search