DVB-T RECEIVER
Contents
1. Item Specification Tuner Frequency Range VHF 174MHz to 230MHz UHF 470MHz to 862MHz Input Impedance 75 Ohms unbalanced Signal Input Level 78 25 dbm Bandwidth 7 8 MHz Demodulation Demodulator COFDM OFDM Modulation 2K 8K FFT SFN MFN Packet Carries 2K 8K Guard Interval 1 4 1 8 1 16 1 32 Connectors RF IN IEC 169 2 female connector RF LOOPTHOUGH IEC 165 2 male connector TV SCART Composite video CVBS RGB audio L R USB USB2 0 Power Input 230V 50Hz Consumption 5 W max Display Decoder Module PAL NTSC Resolution 720x576 PAL 720x480 NTSC Aspect Ratio 4 3 Letterbox Pan amp Scan 16 9 Decoding Video MPEG2 Transport MP ML Audio MPEG2 Audio Layer 1811 Other Compliance ETSI EN 300 744 DVB T Compliance Sound Mode Right Left Stereo 19 SAV ADMEA LOGISAV 21 du clos des charmes 26 rue du clos des charmes 77090 COLLEGIEN FRANCE2. This logo set on the product means that the recycling of this apparatus comes within the framework of the directive 2002 96 EC of January 27 2003 concerning the waste on electrical and electronic equipment WEEE The presence of dangerous substances in the electrical and electronic equipments can have potential consequences on the environment and human health in the cycle of reprocessing this product Therefore at the end of its lifetime this product shall not be disposed with other non recycled waste As the end user your role is of prime importance in the cycles of re using recycling and other forms of valorization of this electrical and electronic equipment Local authorities and resellers have set special procedures for the purpose of collecting and recycling this product You have the obligation to use the selective waste collection systems put in place by your local authorities Table of Contents 1 2 Frontand Rear Panel ni 2 5 3 Remote Controller 6 4 Basic 7 11 5 System Setup 11 15 6 Detailed Operations 16 T Troubleshooting 17 18 B Specifications settee ree tree terete teens 19 1 Introduction Welcome Thank you for choosing this Digital Terrestrial Television Receiver This device will allow you to receive all f
3. Problem Possible cause What to do Standby light not lit Mains lead unplugged Check mains lead Mains fuse blown Check fuse No signal found Aerial is disconnected Check aerial lead Aerial is damaged misaligned Check aerial Out of digital signal area Check with dealer Mosaic blocks in picture or picture freezes Aerial may not be compatible Check aerial Scrambled channel message Channel is scrambled Select an alternative channel Forgotten channel lock code Re install channels to cancle channel lock No response to remote control Receiver off Plug in and turn on receiver Handset not aimed correctly Aim handset at front panel Front panel obstructed Check for obstructions Remote control batteries are inserted incorrectly Check batteries direction Handset batteries exhausted Replace remote control batteries After moving the receiver to another room find can t receive the digital reception The aerial feed may come through a distribution system which may reduce the digital signal now received by the receiver Try a direct feed from the antenna The unit shuts down automatically If no operation is performed from the remote control for three hours the unit will automatically switch to standby mode to reduce power consumption Press the Standby button to put the unit back into operation The USB port does not read multimedia files
4. SCHAUB LORENZ TNT 1745MPEG2 DVB T RECEIVER SCHAUBLORENZ 5 USER MANUAL Please read and keep these instructions Important safety instructions please read carefully And keeps for future reference rain or moisture To prevent the risk of electric shock do not remove the cover or back or this product In case of product failure only qualified personnel can To reduce the risk of fire or electric shock do not expose this product to water repair There are no user serviceable parts inside CAUTION Dangerous tension inside the product Do not open Risk of electric shock No parts can be repaired by the end user Only qualified personnel can repair and maintain this product If the electric cord is damaged it must be replaced by the manufacturer or qualified after sales personnel in order to avoid any danger The product must be installed in accordance with local laws Damaged batteries must be properly disposed In order to protect the environment please dispose the batteries properly in accordance with local laws information is available at your reseller Where to install the product Place the product on a straight rigid and stable place Do not place the product on carpet Do not place the product on top or another that may cause overheating for example receiver or amplifier Do place anything underneath the product for example
5. The USB port on this unit is not designed for playing multimedia content It is only used in the event of software update requested by the manufacturer Important Remarks 1 Analog Reception and DVB T Reception When you wish to watch TV using your TV tuner analog tuner and that your DVB T unit has been turned off or unplugged the image quality can be deteriorated according to the TV you are using This is normal your DVB T unit must be set in standby mode to allow a good quality signal 2 Problems receiving DVB T channels First check that you have well connected your home antenna with the DVB T unit Start a new automatic channel search as follows 1 Press the MENU key from the remote control 2 Then select installation 3 Then select Auto search in order to run the automatic channels search 3 If the reception problem still occurs Your unit has been tested for optimal performance over all the country In most cases the DVB T reception problems are due to a weakness in your home s antenna installation If your installation is old or has never been tested for DVB T the signal can be too weak or flawed for the unit to work properly It is therefore highly recommended that you ask for a qualified technician to test the compliance of your home antenna This unit has been designed and is guaranteed to work with a signal of at least 60dB 18 8 Specification
6. deteriorated according to the TV you are using This is normal your DVB T unit must be set in standby mode to allow a good quality signal 2 Problems receiving DVB T channels First check that you have well connected your home antenna with the DVB T unit Start a new automatic channel search as follows 1 Press the MENU key from the remote control 2 Then select installation 3 Then select Auto search in order to run the automatic channels search 3 If the reception problem still occurs Your unit has been tested for optimal performance over all the country In most cases the DVB T reception problems are due to a weakness in your home s antenna installation If your installation is old or has never been tested for DVB T the signal can be too weak or flawed for the unit to work properly It is therefore highly recommended that you ask for a qualified technician to test the compliance of your home antenna This unit has been designed and is guaranteed to work with a signal of at least 60dB Good to know Main Functions of your Remote Control Menu Navigation Use the MENU button to change the unit s configuration You can also define your favourite channel lists which will be directly accessible by using the FAV button on the remote control To exit a menu or a sub menu press the EXIT button on the remote control to return to the previous screen Audio Language Selection Press the AUDIO butt
7. Setup In System Setup menu a Press Left Right key to select menu pages among OSD Language TV System Region and Time Timer Setting OSD Setting and Parental Lock b Press Up Down key to select menu items among each item c Press OK key to enter the selected item When you enter to System Setup menu you will see the screen like below r gt gt gt gt gt gt TV System Region and Time Timer Setting tting arental Lock 5 1 OSD Language Choose the display language for the on screen menus 5 2 TV System The option Display Mode allows you to choose between PAL for Europe including France Spain Portuguese NTSC and Automatic Aspect Ratio Depending on the format of your television select 4 3 LB 4 3 PS or 16 9 Video Output Select the CVBS Composite or RGB signal LCN Mode Leave this option activated to organise channels in the order predefined by the CSA Standby mode The unit automatically enters Standby mode after 3 hours of inactivity 5 3 Region and Time a Region is used for selecting the country which you are in You can press Left Right key to select each mode circularly b GMT Usage This item is use for open the usage of GMT You can press Left Right keys to switch Off User Define By Region c The GMT Offset item is valid only when the setting of GMT Usage is User Define You can press Left Right keys to switch GMT Offset value and the range
8. draw back from Tools menu 5 9Game When you enter Game menu you will see three Games include Tetris Snake and Othello 5 10 Load Factory Default When you press OK key In the Load Factory Default item a After you input the correct password there will show a warning message to inquiry you The operation will load default and erase all the channels that user added continue b If you select Yes option the all revised parameters of the receiver will reset to default value Please carefully to using this function c ln step 1 and step 2 press Exit key can draw back from this item and without saving iver Information aper atic 1 load default and all the channels that user added continue 6 Detailed Operations AUDIO LANGUAGE Some channels may be broadcasted into multiple languages To change the audio language press the AUDIO key of the remote control 0 Press the DOWN button to change the AUDIO TRACK and then press the RIGHT button to change the current audio Mode SUBTITLES Press the SUB T button of the remote control to activate the subtitles function Subtitles may be available in different languages depending on the channel 7 Trouble shooting If you experience problems with this receiver or its intallation in the first instance please read carefully the relevant sections of this User Manual and this Troubleshooting section
9. CDs or magazines Proper ventilation Place the product in a sufficiently aerated place to avoid overheating Allow atleast 10cm spacing at the back and top of the product and 5cm spacing on both sides to prevent overheating Do not place items such as newspapers tablecloth curtains in front or the ventilating openings Do not expose the product to high temperatures moisture water and dust The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus Do not place other items close to this product that may damage it for example an object containing water or lightened candles Nonaked flame sources such as lighted candles should be placed on the apparatus Electric supply Please unplug the product in case of prolonged non use This product is intended to be used under temperate climate and should not be used under tropical climate If the supply cable is damaged it must be replaced by the manufacturer or qualified after sales personnel to avoid any danger This product must be connected to an electrical supply 230V 50Hz The mains plug is used as the disconnect device so the disconnect device shall remain readily operable 73 23 EEC modified by the directive 93 68 EEC and 2004 108 EC Abrogating This product is compliant with directives 2006 95 EC abrogating the directive the directive 89 336EEC
10. ave Select Yes to save the timer or select No to cancel the operation Sleep Timer a Sleep Timer can set the system enter standby b Press Left Right key to switch the Sleep Time parameter The option is like below Off 10min 30min 60min 90min 120min then press key OK to start sleep time countdown c After you press OK key the Remains will begin to show the timer s remaining time This item is only used to display and can not be modified d Press Exit can exit the current menu 5 5 OSD Setting a Subtitle Display You can press Left Right key to select Off Standard or Teletext If the current channel has subtitle information it will be showed up while this function is on If this function is off there won t show up subtitle information b OSD Style You can press Left Right key to select OSD style C Load Default OSD Setting Press OK to load default OSD setting d Press Exit key to draw back from the OSD Setting menu 5 6 Parental Lock You can set a password for anyone who wishes to operate in the Installation menu And you can also set the password for the lock channels How to set the lock channel please refer to Lock Here will show you how to setting and how to revising the password a In Parental Lock function press OK key there will pop a dialogue for you to input the password The default password is 0000 When you input the correct password you will see a screen like be
11. he FAV button on the remote control in order to watch them In order to select a channel to be classified as favourite press OK Press OK again to cancel the selection You should then assign the selected channel to one of eight favourite channel groups In order to delete a channel from a favourite group select the favourite group concerned then press the 4 button on the remote control b Locking Channels This function allows you to restrict access to certain channels by requiring password entry After selecting a channel choose this option by pressing the 2 button on the remote control A lock appears in front of the channel press the 2 button again to cancel the lock c Skipping Channels This function allows you to skip the selected channels when pressing the keys CH and CH The skipped channels remain accessible when you press their channel number To skip a channel press 3 in front of the corresponding channel d Deleting Channels In order to delete a channel press 4 in front of the corresponding channel Once a channel is deleted you will need to launch a new channel installation in order to be able to watch it again e Renaming Channels To rename channel press 5 in front of the corresponding channel Move the cursor to Esc to cancel the operation 2 Searching Channels You can search the channels according the Channels name A Press 2 key on t
12. he RCU the menu will be shown on the screen b Press Up Down Left Right key to move the highlight in Find window Press OK to input char c Move the highlight to OK and press OK key to save the modification d Press Exit key to cancel the operation 3 Sorting Channels Realign the channels according sort of option a Press number 3 key to sort channel b It will display a dialogue to confirm If you select Yes it will display Sort box c Press Up or Right key to move the highlight and press OK to select sort type such as Default Name A Z Name Z A FTA Lock 4 Moving Channels Move the channels you select to the corresponding place You may assign a channel to a new position which allows you select the channel easier by using CH and CH buttons In order to move a channel select it and press the 4 button on the remote control 4 2 2 Radio Channel List The use of the radio station list is similar to that for the television channels Please note that in most countries including France Spain Portuguese no radio stations are transmitted via the DVBT network 4 2 3 Delete All Favorites This operation will remove all favorite channels includes TV and radio favorite channels from favorite list When you press OK key on Delete All Favorites It will ask you Warning Do you really want to delete all favorite channels Select Yes to confirm or select No to cancel the operation 4 2 4 Dele
13. is 12 00 12 00 increase each half hour progressively d Date and Time items are valid only when the setting of GMT Usage is Off You can press Left Right keys to moving highlight and use number keys to input directly e Summer Time items are valid only when the setting of GMT Usage is By Region You can press Left Right keys to switch f Time display function can control whether the time will be displayed on screen or not g Press Exit key to draw back from Time menu 5 4 Timer Setting Current time information will display on the first row if the current time is incorrect please modify the time information Time item Program Timer This option allows you to set a time at which the DVBT receiver should turn on and display channel on the screen a Timer Mode There are several modes for Timer to setting include Off Once Daily Weekly Monthly m b Wakeup Channel press OK key to enter channel list and select channel that you want to setting c Month Date press Left Right keys to select your wakeup date d Day If Timer Mode is Weekly this item is valid You can select day such as Monday Tuesday Sunday e Time press OK key and number keys to input your wakeup time Once the time s up no matter what the system is in standby mode or in playing mode the system will automatically switch to the channel you want and start to play f Pressing Exit key it will ask you Are you sure to s
14. low b Menu Lock determining that when user wishes to enter Installation menu and Channel List Edit whether have to input Password or not If the setting of Menu Lock is Yes which means user have to key in password set No means unlock c Channel Lock can set the channel which user wants to lock it If you want to see the lock channel you can set Channel lock OFF d New Password is used for revising password you can press OK key firstly then input the new password in this item by using number keys directly After you filled in 4 digital numbers the highlight will auto skip to Confirm Password and ask you to input the new password again If the password is correct the screen will show up a message of change password successfully draw back to system setup menu the revising is complete e Press Exit key to draw back from the parental Lock menu Notes The default password is 0000 Enter this code if the program asks for a password and you have not set one The Super Password is 0786 Use this code if you forgot your own password 5 7 Tools When you switch to Tools menu you will see a screen like below In Tools menu a Press Up Down key to select menu items among each item b Press OK key to enter the selected item Game Load Factory Default Software Upgrade 5 8Receiver Information a When you enter to information menu you will see some receiver Information b Press Exit key to
15. nal to either your TV or another video system 2 RF IN This socket connects to your external aerial 3 USB USB Upgrade 4 SCART OUT This socket connects to your TV 1 First step Connect the unit with your roof antenna Connect your home antenna with the unit s input RF IN The antenna cable is not provided 2 Second step Connect the unit with your television Use scart cable to connect the unit s SCART OUT output to the scart input of your television The scart cable is not provided 3 Prepare the remote control Insert two AAA batteries into the remote control Make sure to respect the polarity sign batteries are not included 4 Welcome Page a When first time power on it will show welcome page like below E Je menus b Press Up Down key to move highlight c Press Left Right key to select region and OSD language d Move highlight to OK button and press OK key to begin to auto scan e Press Exit key to exit menu When you enter to Installation menu there will display the screen like below In Installation menu Remarks lf MENU lock is On input password first Default password is 0000 Important Remarks 1 Analog Reception and DVB T Reception When you wish to watch TV using your TV tuner analog tuner and that your DVB T unit has been turned off or unplugged the image quality can be
16. olume in non menu state 18 CH Used to move around the menu screens or selecting the channels in non menu state 19 RED BLUE GREEN YELLOW BUTTONS These buttons are used to navigate teletext pages 20 RETURN To return to the previously viewed channel 21 Button without function 4 Basic Operations 4 1 Main Menu When you press Menu key you can enter main menu There will display the picture like below a Press Up Down key to select menu pages among Channel Installation Setup and Tools b Press OK key to enter the selected item 4 2 Channel a Press Up Down key to select items between TV Channel List and Radio Channel List b Press OK to enter the selected item Radio Channel List Delete All Favorites Delete All Group Rename 4 2 1 TV Channel List When you enter to TV Channel List menu there will display the screen like below Press the numeric buttons on the remote control in order to Edit Search Sort and Move channels During these operations the system may demand the parental password The default password is 0000 1 Editing Channels Press the 1 button on the remote control to access the menu for editing channels a Favourite Channels Press the 1 button on the remote control to enter the menu of favourite channels You may define one or more channels as your favourites which allows you to access them more easily you will only need to press t
17. on to o Change the audio track to another language if this option is available on the current DVB T channel 3 Remote Controller 12 SCHAUBLORENZ 1 STANDBY Used to switch the set top box to on and off 2 NUMBER KEYS Used to select channel numbers or input numbers in menus 3 INFO Display the detailed information of programs 4 SUB T Used to switch between different subtitles that are broadcasted 5 AUDIO Used to set the sound output the available settings are STEREO LEFT RIGHT 6 TV RADIO Switch between Digital Radio and DVB T modes Radio is not available in countries such as France 7 MENU Used to open the main menu window or return to the previously viewed menu 8 CH Used to move around the menu screens or selecting the channels in non menu state 9 0K Used to confirm a selection within a menu or enter QUICK SELECT to scan program list 10 VOL Used to move around the menu screens or changing the volume in non menu state 11 PAGE UP PAGE DOWN To browse through the pages of channels 12 PLAY PAUSE To freeze the current image and then to resume viewing 13 MUTE Used to turn the sound on or off 14 FAVORITE Used to access your favorite channels 15 TEXT Used to open teletext OSD display if teletext available in the broadcasted stream 16 EXIT To exit the viewing screen or the current menu 17 VOL Used to move around the menu screens or changing the v
18. ree to air DVB T channels broadcast in MPEG 2 The installation is convenient and fast all you need is to connect the unit to your home antenna and to the scart input of your television Auto Standby In order to save energy the electricity consumption of this product has been reduced in both operation mode and standby mode Furthermore if no operation is carried out for three consecutive hours the unit will automatically enter standby mode Simply press the Standby button on the remote control to switch the unit back to operation mode Main Features Full comply with European DVB T standard Full MPEG2 ISO IEC 13818 transport stream compliant audio video decoding Bandwidth of 7 8 MHz supported COFDM demodulator Automatic manual channel search Channel edit moving and deletion Parental lock control NTSC PAL converting automatically and manually Multiple language OSD Supports multi subtitle Package Contents Before installing the product please check that you have in possession the following DVB T Receiver 1 Remote Control 1 User Manual x1 2 Front Panel and Rear Panel Front Panel SCHAUBLORENZ 1 REMOTE CONTROL SENSOR 2 5 INDICATOR Rear panel SCART OUT 1 2 3 4 1 RF LOOP THROUGH This socket will by pass the RF sig
19. te All Use this option to delete all the channels installed After that you will need to reinstall the channels 4 2 5 Group Rename You can rename the group 4 3 Installation When you enter to Installation menu there will display the screen like below In Installation menu Channel Sean a Press Up Down key to select menu items among each item b Press OK key to enter the selected item 4 3 1 Auto Scan When you enter to Auto Scan menu If MENU lock is On input password first Default password is 0000 a Firstly please the country in system setup menu region and time region such as France b In Scan Mode item press Left Right key to select scans all channels or just scans free channels c Moving the highlight to Search item and press OK key to start scanning the Auto Scan menu press Exit key to draw back from the scanning 4 3 2 Channel Scan When you enter to Channel Scan menu there will display the screen like below a There are two modes You can scan channel by channel or by frequency b When scan band is UHF and region France the range of Ch No is from 21 to 69 When scan band is VHF and region is the range of Ch No is from 5 to 10 It s according to region c When you complete your modification move highlight to Search item and press OK key then it will begin to scan d Press Exit key to exit the scanning 5 System
Download Pdf Manuals
Related Search