user manual - SibelGroup
Contents
1. See ANSI 53 1 and ISO 8253 1 standards The booth has door with lock a window that permits the patient to see the operator and viceversa The booth also has a comfortable internal light and all the connections needed to interconnect an audiometer with all its accessories 1 2 PREVIOUS OBSERVATIONS This booth has been manufactured following strict quality control tests However accidents may occur during transport and storage so it is advisable to check the apparatus and complemenatry accessories over before installation WARNING IF ANY DAMAGE IN THE PACKAGING IS FOUND CONTACT THE TRANSPORT AGENCY AND DISTRIBUTOR IMMEDIATELY BEFORE PROCEEDING TO INSTALL THE APPARATUS DO NOT DISPOSE OF PACKAGING BAGS ETC UNTIL THE CORRECT FUNCTIONING OF THE APPARATUS HAS BEEN THROUGHLY CHECKED WARNING DO NOT STORE THE AUDIOMETRIC BOOTH UNMOUNTED DOING SO MAY CAUSE DEFORMATION OF THE PANEL AND THE PRODUCT WOULD NOT BE COVERED BY THE WARRANTY 1 1 Sibelmed USER MANUAL REMOVAL OF WASTE FROM ELECTRICAL AND ELECTRONIC APPLIANCES BY DOMESTIC USERS IN THE EUROPEAN UNION E This symbol on the product indicates that you cannot dispose of the electric part of this product with domestic waste However any removal of this type of waste is the responsibility of the user so the panel and the electric part of the booth must be disassembled and must be taken to a designated collection point for the recycling of electrical and electroni2. Tools Finally place the Roof over the booth laying down on its own weight no need to b geg screwed down If the height of the interior doesn t allow this operation it will have to b done before placing the last pannel sliding it over the lateral pannels check figure 3 To end up tighten the screws definitely and insert the screw covers S40 Booth Assembly Guide A Mount the closing handle in the door with the chromium plated piece in the exterior part and screw together the hold ups Introduce the middle screw in its hole and next put the washer and the nut do not tighten them too much so it can rotate freely A Revise the overall condition of the S 40 Booth Screw down the hold up pillar in the inferior part of the table and then install the table following the pictures sequence B If everything is right and if needed move the booth to its final position with the help of some Ta a for TT convencional lamp 2 QU NUS n people C Connect the audiometer Remember that the booth s pannels are just For LED s simply walls so then the connector number 1 EN optional is linked with the connector number 1 in the Heg tps IDE inside pannel number 2 with number 2 etc accessories that the patients are going to use where a Connect the power cords that are shown up inside p Eta inside the the booth above the window
3. the door will be and how it will turn clockwise or anti clockwise Note Once the front panel is chosen the rear panel must be put in the opposite side and once the door is chosen the side panel must be put in the opposite side The pictures of the next pages show the advisable sequence for the installation 1 6 S40 Booth Assembly Guide NOTE If the door pannel is not already mounted for transportation reasons or you wish to change the opening direction fig 3 do as follows A To change the opening direction turn the pannel 180 Repeat the operation with the To mount the Place the Pannel its feet wheels touching the floor as close as Move the Pannel 2 to fit it over the Door Pannel or Window Pannel Next position the Last Pannel door face the possible to its final position Base s rubber Check its alignment depending on the final position in with the corresponding door hinges and place the corresponding screws put the corresponding screws screws not tight with the Pannel Move the Pannel 1 and fit it over not tight not tight hinges and the Base s rubber having in mind insert the bolts the desired final position for the Door Ea End up fitting Pannel and the Window Pannel lm them with the F help of a hammer Revise the position of the closing wedge and invert it if needed Check that the door fits and can be properly closed pv 5 N
4. CABINA S40 AUDIOMETRIC TEST BOOTH USER MANUAL Sibelmed 7 501 700 MU2 e REV 1 05 Sibelmed USER MANUAL S40 AUDIOMETRIC TEST BOOTH USER MANUAL Rev 1 05 CONTENTS 1 INSTRUCTIONS FOR USE AND INSTALLATION 1 1 1 1 INTRODUCTION 1 1 1 2 PREVIOUS OBSERVATIONS 1 1 1 3 CONTROLS INDICATIONS AND CONNECTIONS 1 2 1 4 INSTALLATION AND STARTTING UP 1 4 2 TECHNICAL SPECIFICATIONS 2 1 3 FUNCTIONING PRINCIPLES 3 1 4 GENERAL MAINTENANCE PREVENTIVE MAINTENANCE AND CORRECTIVE MAINTENANCE 4 1 4 1 GENERAL MAINTENANCE 4 1 4 2 PREVENTIVE MAINTENANCE 4 1 9 MODIFICATIONS 5 1 C PRODUCT ACCORDING TO 93 42 CEE Medical Device Directive Class Revised Approved Date June 2011 Date June 2011 Fa T dl I 44 4 2 T A Jose Maria Plana Carlos Recio Technical Director Sales Director Sibel me USER MANUAL 1 INSTRUCTIONS FOR USE AND INSTALLATION 1 1 INTRODUCTION The SIBELMED S40 AUDIOMETRIC TEST BOOTH has been designed by the R D Department of SIBEL S A using the newest accoustic isolating materials and it has been certified by an international standard referenced laboratory L G A l Exp N 21 006 926 The SIBELMED 540 is an individual chamber that it attenuates the sound waves from outside This characteristic of sound attenuation permits to perform audiometric test in conditions of environmental noise such it is specified to do these tests in some standards
5. NUAL Dp attenuation index by frequency Certifled by L G A I Exp 21 006 926 2 2 26 ws 100 10000 2 2 Sibelmed 7 USER MANUAL Standards Audiometry ANSI S3 1 ISO 8253 1 Quality Sibel s Quality System EN ISO 9001 Safety European Medical Devices Directive 93 42 CEE IEC 601 1 88 Main power electric scheme Draw code 501 725 010 Interconnection electric scheme Draw code 501 725 020 2 3 Sibelmed 7 USER MANUAL 3 FUNCTIONING PRINCIPLES Following the ANSI 53 1 and ISO 8253 1 audiometric Standards the audiometric tests must be performed at conditions that the environment noise do not mask the test results To achive this the booth is a sound isolated space therefore the sound noise insides is much less than outsides So it permits to perform the audiometric tests correctly The booth is made of panels that they have different sound isolating material layers The basic physics principle is known as the mass law Other considerations which should be notice to have a good sound attenuation are based in the proper material combination as their sizes All this is done to avoid unwanted effects as the coincidence effect For more information it can be condulted Acoustics and Sound Isolation Manuals 3 1 Sibel me USER MANUAL 4 GENERAL MAINTENANCE PREVENTIVE MAINTENANCE AND CORRECTIVE MAINTENANCE The S40 audiometric test booth requires a genera
6. c appliances The separate recycling and collection of this waste at the time of removal will help preserve natural resources and ensure that recycling protects your health and the environment Should you require further information on the places where you can leave this waste for recycling contact the local authorities in your town or city the domestic waste management service or the distributor who sold you the product 1 2 Sibelmed USER MANUAL The audiometric test booth has the following units and accessories CODEQTY DESCRIPTION 901 700 000 1 SIBELMED S40 TEST BOOTH 305 350 030 1 MAINS CONNECTION CABLE 901 700 MU1 1 USER S MANUAL 901 750 001 1 AUDIOMETER BOOTH INTERCONNECTIONS 6 119 330 010 4 WHEEL FOR 540 TEST BOOTH OPTIONAL Furthermore the test booth is compound of the next units CODE QTY DESCRIPTION 901 711 010 1 TRAY 901 711 030 1 SUPPORT COLUMN 901 741 040 1 BASE PANEL 901 720 000 1 FRONT PANEL 901 741 010 1 SIDE PANEL 901 731 010 1 DOOR FRAME 901 731 020 1 DOOR 901 741 020 1 REAR PANEL 901 741 030 1 TOP PANEL These codes could be used to order accessories and spare parts MANUFACTURER S RELIABILITY SIBEL S A will hold itself responsible for the safety reliability and correct functioning of this device only when Reparations servicing and modifications both inside and outside the warranty period are carried out by SIBEL S A s technical personnel Then equipment is used by qualified pe
7. l and preventive maintenance as do any equipment and particulary those witn medical applications It has the object of assure the safety of the patient operator and environment and guarantee the reliability and accuracy of the functions for which it was made This entails a series of routines that must be performed 4 1 GENERAL MAINTENANCE The general maintenance is necessary to keep the device functioning correctly The person who carries out this operation needs no special technical knowledge except familiarity with the functions and handling of the device The user of the device should normally do the job himself The tasks to be carried out are as follows The external surface of the booth can be washed with soap and water then wipe the booth dry Inside the booth the foam walls and the floor can be cleaned using a conventional vacuum cleaner the plastic parts and the window can be cleaned with soap and water Do not use abhrasive substances or solves 4 2 PREVENTIVE MAINTENANCE The preventive maintenance consist of all the actions designed to keep the machine in good working order 4 2 1 CHECKING The user can check periodically the aspect of the booth the indoor light the door lock and the interconnections work correctly and there are not noises that can disturb the audiometric test 4 2 2 CHECKING THE INTERCONNECTIONS Every six months the user can check that the interconnections work correctly and they do not produce noises
8. rsonnel and according to the recommendations in this User s Manual The set of S40 Audiometric Test Booths has the following models S40 A 90x90x215 cm S40 B 110x110x215 cm 540 C 125x125x215 cm S40 D 85x72x187 cm For mobile units S40 E 135 x 135 x 215 cm S40 F special measures 1 3 Sibelmed 7 USER MANUAL 1 3 CONTROLS INDICATIONS AND CONNECTIONS 1 3 1 GENERAL VIEW Fig 1 1 N 1 Front Panel N 2 Connection board for audiometer and power mains N 3 Tray N 4 Window N 5 Screws N 6 Top Panel N 7 Ventilation Slots N 8 Side Panel N 9 Rear Panel N 10 Base N 11 Door Frame N 12 Door 1 Sibel med 7 USER MANUAL N 13 Door Lock N 14 Rubber feet N 15 Support Column 1 3 2 CONNECTION BOARDS Fig 1 2 and Fig 1 3 N 16 Conections for the accessories of audiometer N 17 Light pilot of the main switch 16 N 18 Main power outlet for the audiometer N 19 Main power inlet N 20 Characteristics Board N 21 Main switch 2 16 0 40 CABINAS INSONORIZADAS 18 1 1 5 Sibelmed 7 USER MANUAL 1 4 INSTALLATION AND STARTTING UP 1 4 1 INSTALLATION To perform the installation of the test booth it is a must to follow the next steps Choose the site where you are going to put the booth and its position lt means to choose where the front panel with its window and tray will be and where
9. that can disturb the audiometric tests 4 3 CORRECTIVE MAINTENANCE Corrective maintenance refers to leaving the equipment in good working condition when after malfunction or improper use the device no longer works and needs to be repaired When a malfunction which impedes normal use is detected contact SIBEL S A s After Sales Sevice specifying the type of problem produced in the greatest detail possible 4 1 Sibel med USER MANUAL 5 MODIFICATIONS 5 1
10. the jack of each accessory and then plug the outlets and inlets of the audiometer in the outdoor jacks of the booth N 15 that have the same number so the numbers will be the same at the two sides and the accessories will be connected properly Switch on the main switch N 21 and turn on the audiometer also Check the properly functioning of the audiometer following its user s manual IF YOU HAVE ANY DOUBT IN THE INSTALLATION PROCEDURES OR ANYTHING ELSE CALL THE AFTERSALES SERVICE OF SIBEL S A OR HIS DISTRIBUTOR 1 9 Sibelmed 7 USER MANUAL 2 TECHNICAL SPECIFICATIONS Description individual soundproof booth for audiometric test execution Reference Model Dimension 01634 S40 A 90 x 90 x215 cm 01636 S40 B 110 x 110 x 215 cm 01637 S40 C 125 x 125 x 215 cm 01639 S40 D 85 x 2 x 187cm Meets R43 ONU glazing in vehicles 01640 S40 E 135 x 135 x 215 cm 07107 S40 F Special Measures Window Dimensions 59 x 46 cm Door Dimensions 53 x 184 5 cm Tray Dimensions 70 x 40 cm Power 220 V 50 60 Hz other voltages optional Passage of electric circuit network switch and light signaling Internal lighting for incandescent lamp lamp Led s Internal Power Consumption less than 40 W Maximum load 500 W Accessory bypass connections Five 6 3mm Stereo female jacks and one 3 5mm Stereo female jack Minimum global attenuation using white noise with a bandwith from 250 to 8000 Hz 33 5 dB 2 1 Sibelmed 7 USER MA
11. to each of the terminal booth having in mind this endings of the lamp socket s base Put and fasten the position must not bother the cover of the lamp socket s base with the attached Place the Sb patient and must allow to NOTE D perorm The booth must never be in contact to any wall to They should be lined up and avoid the transmission of vibrations b Connect the wires to the terminal and hold the lamp to the wall of the booth Switch on the on off button of the lamp and leave it on to allow acting to the general switch of the booth equidistant to each other Make sure that the S40 Booth is not connected to the mains power supply yet Sibelmed USER MANUAL 1 4 2 STARTING UP Follow the next steps to start up the test booth NOTE It is supposed taht the users has an audiometer to connect in the booth NOTE Connect the main power wire to the inlet of the connection board and plug it to the mains Check that the light pilot N 17 and the indoor light turn on off when switching the main switch N 21 In the case that the light will not turn on check the step before and the main power Turn off the main switch Put the audiometer over the tray and connect its power wire to the outlet of the connection board N 19 WARNING Maximum load 500W Plug all the accessories of the audiometer in the indoor connection board of the booth N 16 and hang them at the hangers Remember the number of
Download Pdf Manuals
Related Search