Telic Standard BC
Contents
1. Page 33 Telic Telematik amp Telemetrie Content Description Digital Inputs 01 gt 1 0 Digin2 1 Digital Outputs 10 gt DigO utl 1 DigO ut2 0 Analog value of Analog Input 1 external power supply Input 1 Analog value of Analog Input 2 voltage of the backup battery Input 2 13 1 1 Event and Log Codes This code describes which event was the reason for a particular status report The following event codes are implemented Code Description 1 Start Up Event this event is sent immediately after switching the device on It contains the last valid G PS position which was typically generated when the ignition changed from ON to O FF 6 Change of Direction Event Default minimum speed 6 km h minimum change of direction compared with the value of the last status report 60 degrees 11 Digital Input 1 changed from low to high 12 Digital Input 1 changed from high to low 13 Digital Input 2 changed from low to high 14 Digital Input 2 changed from high to low 15 External power source was connected to the device 16 External power source was removed from the device Page 34 13 1 2 Telic Telematik amp Telemetrie Description 98 The device has moved more than a configurable distance straight line away from the G PS position of the last status report The Kilometer Counter A kilomete2. In the target area position reports will be more freguent again because the vehicle must turn left or right at various crossings in order to hit the target address of the trip This feature can be disabled and the value can be changed Please contact the supplier of the device if you want to change the value or you want to disable the feature at all Direction based Status Reports The Telic Standard BC remote control unit is configured to send a direction based status report every time the angle between the direction reported in the last status report and the current direction is more than x degrees Default 60 degrees The above mentioned default value ensures that most of the direction changes ata crossing will be recognized and reported This feature can be disabled and the value can be changed Please contact the supplier of the device if you want to change the value or you want to disable the feature at all Status Reports due to Special Events The Telic Standard BC remote control unit sends a status report if one of the following situations occurs Event Description The Telic Standard BC remote control unit sends a A digital input status report every time when a digital input changes its status changes its status e g when IGNITION is switched ON or OFF The Telic Standard BC remote control unit sends a Disconnection status report every time when the device is from external disconnected from the external
3. on Page 21 Telic Telematik amp Telemetrie If the Telic Standard BC remote control unit is switched off you can switch it on by moving the switch marked with O N 1 with a non metallic tool e g a toothpick from position 1 into the position marked with ON You can find the switch below the cover of the SIM card near to the edge of the device If you want to switch the device off then please move the switch marked with O N 1 with a non metallic tool e g a toothpick from position O N into the position marked with 1 Tip indication 1 of the switch does not mean ON 1 indicates pin 1 of the switch The tracking via a tracking program or a tracking server Die Usage of the Telic Standard BC remote control uniton a tracking program or a tracking server is the preposition for the efficient usage of the Telic Standard BC For the set up of the Telic Standard BC remote control unit the Telic Standard BC has to be configured with the necessary data For this purpose a configuration SMS Short M essage has to be sentto the device which includes the operation relevant parameters e g the IP address of the server to which the tracking data have to be sent Alternatively to that the configuration parameters can also be set up via the serial interface pls see as well chapter 12 48 After the configuration of the relevant parameters status messages will be generated and will be sent via G PRS Together wit
4. 1 The analog inputs The analog inputs of the Telic Standard BC remote control unit reflect the actual status of the voltage supply of the Telic Standard BC remote control unit Within the transmitted data a numeric value is indicated being between 0 until max 255 10 1 Board net voltage analog input 1 The value of the analog input 1 represents the voltage value of the board net 1 Digit is the equivalent of 0 064V O ffset 0 34V 10 2 Battery voltage analog input 2 The value of the analog input 2 represents the voltage value of the internal battery 1 Digitisthe equivalent of 0 0198V 11 The Serial Interface The Telic Standard BC remote control unit provides a serial interface with a female DSUB 9 connector This interface can be used for the following purposes e Access to internal debugging messages These messages are mainly used for debugging the software of the Telic Standard BC remote control unit in case there are bug reports which must be evaluated e The Telic Standard BC remote control unit can be used asa pure GSM modem This mode can for example be used in conjunction with a standard handheld PC like for ex PSION TECLO Workabout in order to transmit data between any third party application and the handheld PC Page 25 11 1 Telic Telematik amp Telemetrie Internal Debugging Messages The Telic Standard BC remote control unit can be connected to any standard PC using the serial interfa
5. Blinking Patterns The device has four LEDs The blinking patterns of these LEDs can give you valuable information about the proper function of the device Description of the Blinking Patterns LED on the right side dose to the connector for the GPS antenna This LED is blinking yellow and reports the status ofthe GPS reception as follows off GPS is not activated 1 blink no valid GPS information is available 2 blinks a valid GPS information is available but without height information 3 blinks Complete G PS information is available After switching the device on as well as after a phase without G PS reception the device only accepts 3D GPS positions This ensures that position reports with serious deviations from the real position are not reported to the control center After a while 2D position reports are accepted because the G PS receiver then had enough time to evaluate the signal quality of all available G PS satellites Page 30 Telic Telematik amp Telemetrie Description of the Blinking Patterns The LED in the middle consists of 2 LEDs a green LED and a red LED The green led is continuously on as soon as the Telic Standard BC remote control unit is powered by an external power source LEDs in the au middle The red LED indicates if the internal backup battery is currently in the process to be charged If the LEDs in the middle are both off this does not mean thatth
6. account that you are moving and on the other by checking to see if the received G PS positions make sense compared to the route being driven You would not turn and drive into a field 100 meters before an intersection A remote surveillance module cannot and should notuse such tricks Page 10 5 5 5 5 1 5 5 2 5 5 3 5 54 Telic Telematik amp Telemetrie What are the necessary components of a remote surveillance module Now that you are the proud owner of a remote surveillance module you would like to know What does it need to smoothly operate it Power Source The remote surveillance module needs to be connected to a power source 7 volt 36 volt direct current It can be powered by a car battery rechargeable battery or a power plug Antennas In order to use the device a combined antenna or two antennas are needed e aGSM quad band 900 MHz 950 MHz 1800 MHz 1900 MHz antenna to communicate over the mobile network e an antenna to receive GPS position satellite signals The antenna included with the Telic Standard BC device is a combined GSM GPS quad band antenna This makes mounting the antenna inside the vehicle as easy as possible Under certain circumstances it may be necessary to use special antennas In such a case the enclosed antennas may clash with other devices with the same electrical value O ther antennas e g roof antennas and other useful additional devices can be found atwww
7. amp Telemetrie The voltage provided by the digital outputs is the same like the voltage of the power supply of the device A current of max 400mA can be drawn from each digital output The blue wire is connected to Digital O utput 1 the white wire is connected to Digital O utput 2 Pin out and Colors of the 6 pin Molex Connedor DigiOut 1 Digit 1 Iginition Please note that Digital O utput 1 and Digital O utput 2 provide VCC if they are activated You should never connect these two wiresto GRO UND This can destroy the device If you do not use some of the wires of the MO LEX connector then please ensure that these wires cannot get into contact by accident with any metal parts of the vehicle Page 19 5 6 6 Telic Telematik amp Telemetrie Sixth Step Mounting the Remote Surveillance Module In order to protect your vehicle from theft and vandalism the device should be installed in a location where the device its antennas and its power supply are well hidden and where it is easy at the same time to switch the main switch of the device located below the SIM card holder on and off Using the corresponding two screws and holes in the device please mount the device ata suitable dry location When mounting the antennas please be aware that the antennas must have a free view to the sky not blocked by metal or liquids in order to receive good signals The antenna should have a minimum distance to metallic
8. and ignition brown to the vehicle pin 15 of the vehicle o Connect the black cable to GRO UND of the vehicle pin 31 of the vehicle o Connect the white MO LEX connector to the device 14 2 Quick test Move the vehicle to a place where the Telic Standard BC remote control unit has good GPS and GSM reception free view to the sky on all sides A good GPS signal is indicated by the yellow G PS LED which is located close to the G PS antenna connector flashing three times continuously Make sure that you have a good reception of the G SM signal A good GSM signal is indicated by the green G SM LED close to the connector for the GSM antenna flashing two times continuously according to chapter 12 1 1 Verifcation of the LEDs blinking paramters 15 Factory settings The device contains a set of default values that have influence on the status messages sent to the control server The default values have been selected very carefully by Telic in order to be suitable for most of the Telic customers If you d like to change the configuration of one or the other value please contact your supplier of the device He can load a new configuration file into the device over the air Page 39 Telic Telematik amp Telemetrie 15 1 SIM Card specific Parameters 15 1 1 15 1 2 PIN Code of the SIM Card The device assumes that the PIN code of the SIM card is 0000 Alternatively you can insert a SIM card with a de activated P
9. 0 volt The color of the wire of Digital Input 1 is green The status of this digital input is reported with each status report to the control server and can be found in a report Function if G RO UND or nothing or a voltage between 0 0 volt and 1 0 voltis connected then the input reports O FF If a voltage between 7 0 volt and 36 0 volt is connected to the input O N will be reported If a voltage between 1 0 volt and 7 0 volt is connected to the input the result will be undetermined Page 17 5 6 5 3 5 6 5 4 Telic Telematik amp Telemetrie Digital Input 2 IGNITION The Digital Input 2 can be connected to any signal which reports or O FF The input can be used with a voltage up to 36 0 volt The color of the wire of Digital Input 2 is brown Function if GRO UND or nothing or a voltage between 0 0 volt and 1 0 volt is connected then the input reports FF If a voltage between 7 0 volt and 36 0 volt is connected to the input O N will be reported A multitide of tracking programs from Telic respectively from Telic Partners use Digital Input 2 as IGNITIO N input We therefore strongly recommend to connect Digital Input 2 to IGNITIO N vehicle pin 15 Digital Outputs 1 and 2 Um utput 2 The digital outputs 1 and 2 can be switched with an SMS command or with a GPRS command Please ask your supplier for details Page 18 5 6 5 5 Telic Telematik
10. 5 1 00 07 54 INFO GPS 1165069352 021206142159 3 525204 133248 193 0 107 6 00 07 54 INFO DB 2 2 0 211 00 07 54 INFO 2050 29 3 GSH 442 00 07 54 INFO AD 236 218 00 07 56 INFO 1 60 1 26203 398 2 00 07 58 INFO GPS 1165069355 021206142202 3 525204 133247 186 0 108 6 00 07 58 INFO DB 2 2 0 211 00 07 58 INFO IP 60 1 26203 401 2 00 08 00 INFO EVENT 14 00 08 00 INFO MSB 183900458414 021206142204 0 021206142204 13324 7 525204 3 0 110 180 211 00 00 236 218 88 00 08 00 INFO TCP SENT BIN 00 08 00 INFO GPS 1185063008 021206142205 3 525204 133246 177 0 112 6 00 08 00 INFO DB 2 2 00 08 02 INFO 6 56208 104 2 00 08 02 INFO TCP RECEIVED 1839004584 1 15 00 08 04 INFO GPS 1165069362 021206142209 3 525204 133245 165 0 114 6 00 08 04 INFO DB 2 2 0 211 00 08 04 INFO CSQ 29 0 GSM 452 00 08 04 INFO RD 244 218 00 08 06 INFO IP 60 1 26203 407 2 00 08 08 INFO GPS 1165069365 021206142212 3 525204 133245 160 0 116 6 00 08 08 INFO DB 2 2 0 211 00 08 08 INFO 60 1 26203 410 2 Verbunden 00 00 33 Autom Erkenn iisz008 N 1 RF GROSS Auzekhnen jDruckerecho Page 28 Telic Telematik amp Telemetrie 11 2 The transparent GSM modem Mode The Telic Standard BC remote control unit can be used in two modes Vehicle tracking mode VTU mode Transparent G SM modem mode If the device is operated in the transparent SM modem mode it acts like a standard GSM modem which mea
11. IN code verification The GPRS parameters can be set via SMS or via the serial connection Example of configuration via ser connection IPCONFIG al net ppp alplus at ppp alplus at Example of configuration via SMS 00B0008866 a1 net ppp alplus at ppp alplus at where 00 Message ID variable between 00 and 99 BO Code zum Setting the IP configuration 008866 the last 6 digits of the labelled serial number ofthe device 2 Parameter IP Address IP Port which shouldn t be changed in this case al net ppp alplus at ppp alplus at APN User name and Password More details are described in the Software Protocol specification Roaming In some cases itis much more expensive to transmit data thru G PRS if you are outside your home country compared with the tariff inside your home country Price difference can easily be a factor of 10 and more in the same country The Telic Standard BC remote control unit provides the possibility to load a GPRS roaming table into the device This allows specifying which G SM network provider s should be used in which country depending on the SIM card thatis inserted into the device If you d like to adapt the GPRS roaming table then please contact your supplier of the device He can load a new configuration file into the device over the air adapted to your needs As an alternative you can block the SIM card used inside the Telic Standard BC remote control unit to be used outs
12. Telic Telematik amp Telemetrie User Manual for Telic Standard BC Telic Telematik amp Telemetrie 1 A Word in Advance Thank you very much for choosing to purchase a remote surveillance module from Telic The remote surveillance modules of the Telic locate product line belong to a highly esteemed class of devices Especially noteworthy is the price performance ratio of these devices The device can immediately inform you if your vehicle is for instance forcibly removed from its location Using the coordinates transmitted from the device you a security centre or the police can determine where the monitored object is Furthermore using optional sensors attached to the device you can be immediately informed if something with your vehicle is not as it should be We wish you lots of success with your new Telic device We have carefully checked the information that follows for accuracy The documentation is however not a warranty of product attributes Telic strictly adheres to the established sales and delivery terms Propagation or duplication of the product s documentation or software and its contents are only permitted with written permission from Telic G mbH Trademarks The Telic logo and the terms Telic and Telic Standard BC are registered trademarks of Telic G mbH All other names and labels used in this document are the registered trademarks of their respective owners Telic does not preclude the poss
13. Telic delor on request under info telic de Mobile Technology SIM card Information from the remote surveillance device is transmitted over the cellular network As a result a 3 voltor a 1 8 volt SIM card is needed A prepaid SIM card or a contract card can be used If possible avoid prepaid SIM cards Prepaid SIM cards have the advantage of having no base fees However they have the big disadvantage that at some point the card will be used up This results in the remote surveillance module not being able to send an alert in an emergency situation In order to avoid this situation we advise you not to use prepaid SIM cards Page 11 5 6 5 6 1 5 6 2 Telic Telematik amp Telemetrie Getting started The remote surveillance module can be installed into your vehicle using the following six steps First Step Open the Device Please open the SIM card cover by sliding the cover in the direction of the red arrow The SIM card cover con be found on top of the device below the three LEDs Second Step Insert the SIM Card Before the Telic Standard BC remote control unit logs into the device it checks if the SIM card inserted into the device needs a PIN code to operate properly If this is the case it is necessary to change the PIN code of the SIM card to 0000 The PIN code of the SIM card can be changed with any GMS mobile phone Some SIM cards also allow to de activate the PIN code In this case you have
14. ack plastic Page 45 Telic Telematik amp Telemetrie Description Approvals El Telic GmbH Raiffeisenallee 12b D 82041 Oberhaching near Munich Germany www Telicde Page 46
15. antenna G PS antenna Please connect now the two antennas according to the picture below You cannot mix the two antennas because they have different connectors connector for the GSM antenna connector for the GPS antenna Page 14 5 6 5 5 6 5 1 5 6 5 1 1 Telic Telematik amp Telemetrie Fifth Step Connecting the Unit to the Vehicle Please connect the Telic Standard BC remote control unit to the vehicle according to the following instructions using the connection cable with the white 6 pin MO LEX plug which is included with the device Please do not connect the white connector to the Telic Standard BC remote control unit before all cables you intent to use are connected to the vehicle Power Supply Depending on the intended mode of usage you can connect the device to the power supply in two different ways The device must stay active after ignition off This operating mode has the disadvantage that the device even consumes power while the ignition is off This means that the battery of the vehicle can run out of energy which means that the vehicle might not be able to start its engine after a few days without operation depending on the size age and charging level of the battery The advantage of this operating mode is thatthe device is able to connect faster to the GSM network and it can find faster a new PS position after ignition was switched from O FF to ON This means that for example wo
16. ce of the device The serial cable needed can be ordered from Telic After connecting the Telic Standard BC remote control unit and the PC with the serial cable please open your favorite terminal program like Windows HyperTerminal or ZOB After launching Windows HyperTerminal the following window appears gt New Connection HyperTerminal Unlicensed inl xl File Edit View Cal Transfer Help Dels s talg Connection Description 2 xl a New Connection Enter a name and choose an icon for the connection Name vit Disconnected Auto detect Auto detect 50501 CAPS num Capture Print echo In the field named Name please enter any name of your choice and confirm this name by clicking the OK button In the subsequent window please enter the serial COM portof your PC you connected the serial cable to Page 26 Telic Telematik amp Telemetrie Enter details for the phone number that you want to dial Country region Deutschland 49 Area code 030 Phone number Connect using Cancel If you are using USB to serial converter then you need to select the virtual serial port of this converter To find out which virtual CO M port is used by the adapter please click Start gt Settings gt System management gt System gt Hardware gt Device manager gt Connections There you will find the name of the virtual serial port in brackets besides th
17. components of the vehicle in each direction E The included combined G SM G PS antenna is only intended to be mounted inside the vehicle because the antenna cannot withstand wet environment O ther types of antennas e g roof antennas are available Please contact your supplier of the device A perfect place for the combined G SM G PS window antenna is inside the vehicle glued to the windshield with the adhesive side of the antenna under the white protection paper Please clean the window with alcohol or similar and then remove the white paper in order to fix the antenna at the desired place Page 20 5 6 7 Telic Telematik amp Telemetrie If you choose another place for the antenna please ensure that the side of the antenna with the white paper points towards the sky This is important because this side of the antenna is the active one Attention a buckled orfurled cable can even if its isolation is not damaged reduce the guality of the received signal significantiy so that a proper function of the device might not longer be given Please also be aware that metallised windshields can strongly block the signals of the G PS satellites causing reception of the G PS position signals to be impossible In addition the antenna should not be mounted behind the O FF position of the windscreen wiper Switching the device on and off Normally the device is delivered by Telic with the power switch being switched
18. coordinates Possible cause Solution The GPS antenna is not connected correctly Please connect the G PS antenna accor ding to chapter Fourth Step onnecting the Antennas The GPS antenna does not have a free view to the sky The GPS antenna must always have a free view to the sky 0 uite often antennas also have symbols that point the way the antenna should be mounted they might for example have an upper side and a bottom side Windows of cars that are protected with a metal layer to protect the driver from the sun do not allow the PS signal to go thru In this case the GPS antenna must be mounted outside the vehicle e g on the roof or behind the windows in the fond of the car which sometimes have no metal layer even if the front window has a metal layer Your vehicle is ata place with bad GPS signal A good reception of the G PS signal is only possible if the G PS antenna hasa free view to the sky In order to have positive test results please move your vehicle to an appropriate place no houses around no garage etc Further hints regarding the potential problem with your Telic Standard BC remote control unit can be retrieved from the four LEDs which are implemented into the unit Details regarding the LEDs can be found in chapter Testing the Device erify the proper installation as follows After the installation of the device inside the vehicle we strongly recommend t
19. d resets the unit as soon asa malfunction of the program is detected The watchdog covers a big range of potential malfunctions like problems with the GSM connection problems with GPS reception etc This watchdog ensures that the unit will automatically return to a stable status aftera malfunction There is no need for the user to configure the watchdog If the watchdog needs to restart the device after a malfunction it can happen that a few status reports cannot be recorded and therefore will not be transmitted to the control server because the Telic Standard BC remote control unit cannot record status information while being in the restart phase The Status message Status messages are data sets having been generated due different types of events Status messages will be sent immediately after their creation or also out of the database via GPRS to the control server 13 1 Content of a Status Report Content Description Event Log reason for the status report Code Event Log time stamp of the event Timestamp GPS GPS timestamp of the moment when the G PS coordinate was Timestamp recorded Longitude longitude in 100u degrees in binary mode 101 Latitude latitude in 1004 degrees in binary mode 10 2 Fix Type 1 2 or 3 depending on 1d Fix 2d Fix or 3d Fix Speed over speed in km h ground Course over direction in degrees 0 degrees North ground Mileage Kilometer counter in meters
20. e name of the USB to serial converter Click OK when you are finished with the configuration of the name of the COM port In the next window please enter the data as shown below Page 27 Telic Telematik amp Telemetrie COM1 Properties Port Settings Bits per second Data bits Parity Stop bits Flow control Hardware Restore Defaults Cancel BIP As soon as you click on OK HyperTerminal will display debugging messages of the Telic Standard BC remote control unit as follows B1 HyperTerminal 18 Datei Boarbeten Aet Anden bertragung 7 Ole 515 oa 00 07 36 INFO GPS D 021206142141 3 525204 199248 199 0 97 5 00 07 36 INFO DB 2 2 0 00 07 38 INFO TP 60 1 56208 380 1 00 07 40 INFO GPS 1165069397 021206142144 3 525204 133248 193 0 99 5 00 07 40 INFO 2 2 0 211 00 07 40 INFO 60 1 26203 00 07 42 ner GPS itf 120614217 3 525204 133248 194 0 101 5 08 07 42 INF DB 2 2 0 2 00 07 44 INEO 1P 60 i 36209 386 1 00 07 44 INFO CS0 28 0 GSH 432 00 07 44 INFO RD 235 17 00 07 46 INFO GPS er ent 021206142150 3 525204 133248 194 0 102 7 00 07 46 INFO DB 2 2 0 211 00 07 46 INFO 202682 126209389 1 00 07 48 INFO GPS 1165069346 021206142153 3 525204 139248 194 0 105 6 po HE 48 eae DB 2 2 1 26203 00 07 92 INFO Gps 1166060813 021206142156 3 525201 133048 194 0 106 6 00 07 52 INFO DB 2 2 00 07 52 INFO 1P 6 1 26203 29
21. e GPSisa set of 24 satellites that send out positioning signals free of charge This signals can be used to calculate the current position of a vehicle anywhere in the world with little technical needs e GPRSis a very cheap TCP IP connection of the Telic Standard BC remote control unit to the internet Data exchange using G PRS is much cheaper than data transmission using SM S messages In most cases the billing of the connection of the device to the internet is not based on time but on data volume basis Because the Telic Standard BC device sends very small amount of data to the intemet many thousand status and position reports can be sent to the internet for less than 10 Euros in most countries around the world If you want to use the G PRS interface of the Telic Standard BC remote control unitthe SIM card you are using must be enabled for using the G PRS service Please contact the provider of your SIM card All SIM cards Telic is delivering are already G PRS enabled Precision of the GPS Position Page 9 Telic Telematik amp Telemetrie The lobal Positioning System PS was developed in the early seventies by the U S Department of Defense It is comprised of 24 satellites in various locations around the globe Due to the travel patterns of the satellites and their transmission technique the precision of the data has its limits Here we briefly present them A GPS receiver calculates its position by differentia
22. e Telic Standard BC remote control unit has been switched off Instead this means that the device currently does not receive any power from an external power source This green LED indicates the G SM status and at the same time it indicates if the device is switched on at all LED is off the GSM module has been switched off LED is continuously onG SM has been switched on but no G SM network is available EM pid lert Single flash GSM connection has been established and GPRS is available but no dose to the connection to the control server been connectar for established the GSM antenna Double flash GSM connection has been established and G PRS is available connection to the control server has been established 2x blinking incoming SMS 3x blinking outgoing SMS Page 31 12 1 2 12 2 12 3 12 4 Telic Telematik amp Telemetrie Test Transmission of a Status Report After you have verified that all 4 LEDs are showing the expected blinking patterns we strongly recommend a test transmission of a status report as follows Park your vehicle ata place with a good view to the sky Switch the ignition on It is not necessary that the engine is running Wait minimum 5 minutes Switch off the ignition Now you should see an actual position report in your control center software Details regarding your control center software and functionality is available from your dealer Buffering of Data while GSM Recep
23. ected a low is recognized as well Page 23 9 1 Telic Telematik amp Telemetrie For each change of the digital input a status message incl the latest valid G PS position will be sent to the control center The digital Outputs A change of the digital outputs can be made via GPRS from a Server A change of the digital outputs via SMS in 7 Bit text format as usual in a regular G SM Mobile network device is also possible Switch of the digital outputs The digital outputs can be via GPRS or SMS The related message is as follows 004000886610 With this SMS the digital output 1 is set and the digital output 2 is re set The message is composed of 00 Message ID free choice between 00 and 99 40 Code Setting of the outputs 008866 the first 6 numbers of the labelled serial number of the device xy Mask for change of the digital outputs x DO UT1 y DO UT2 More details are described in the Software Protocol Specification 9 2 Automatic answer of the digital outputs fit has to be ensured that the outputs have been set respectively re set correctly there can be requested an acknowledgement from the remote control unit This can be done via the codes 41 Example 004100886610 to be sent via SMS or G PRS Reply 0044008866TSBC 0019 1 359563000008668 241006114259 115872 480 334 3 0 340 0 10 00 223 217 The reply is re tramsmitted via G PRS only Page 24 Telic Telematik amp Telemetrie
24. h them also the G PS position and the status of the digital In and O utputs as well as the measuring values of the analogue Inputs will be additionally sent More details for this you will find in chapter 12 4 The status message General functionality of Telic Standard BC The Telic Standard BC remote control unit has primarily the task to communicate GPS position data with additional status information via an existing TC P IP connection as status messages If a message can t be communicated it is stored in the device and will be sent later on There can be stored min 1000 position messages The following events will create a position messages e The driving over a distance of x meters air line x is configurable in where ever direction x is configurable Page 22 Telic Telematik amp Telemetrie change of direction by a configurable minimum angle during a ride at a as well configurable minimum speed e Changes of status atthe both digital Inputs Cutoff and Connect to the main power supply After the switch on of the Telic Standard BC remote control unit at the beginning the GSM module as well as the GPS module will be switched on As soon as the G SM module has successfully logged into the G SM network all currently available GSM networks are recorded which allow using G PRS with the SIM card inserted into the device Then a GPRS connection and a TCP IP connection will be established to the preconf
25. ibility to change the data in question without announcement and takes no responsibility for technical imprecision and or omissions O berhaching den 16 Februar 2007 2006 Telic GmbH O berhaching Version 100 Page 2 Telic Telematik amp Telemetrie Tips for the use of this manual This documentation is directed towards users of the remote control unit Telic Standard BC In order to bring you this documentation several employees from different departments of the company have worked together to bring you the best possible support for the use of your Telic product If you should however find a mistake or would like to provide a suggestion please send an e mail directly to E Mail info Telic de This documentation should help you to take advantage of the many functions of the device Please read itthrough carefully If you are in a hurry and would like to catch up with the details later then skip to Chapter 14 Quick Start on page 39 There you can find a condse tutorial which will get you up and running in no time Page 3 Telic Telematik amp Telemetrie Content of this manual Telic Telematik amp Telemetrie l 1 13 2 1 6 Telic Telematik amp Telemetrie 15 1 2 Roaming 15 2 Default Values 6 Error Handling Power consumption 1 Technical information Page 7 j 5 1 5 2 Telic Telematik amp Telemetrie Introduction What is a remote su
26. ide your home country In this case the device can remember up to 1 000 status reports that will be sent to the control server as soon as the vehicle enters the home country again and therefore can use the cheap local G PRS tariff Page 40 Telic Telematik amp Telemetrie 15 2 Default Values The unit contains the following default configuration Parameter Default Value Distance between two waypoints 5 000 m G PS kilometer counter 0m GPRS reconnect delay 605 Internet address of the control sever No default GPRS IP port of the controls server No default Direction event threshold 60 degrees and a minimum speed of 6 km h Binary data transmission De activated With this configuration the amount of data to be transmitted per status report can be significantly reduced without any loss of information compared with an representation of the data Acknowledge Mode De activated With this configuration the amount of data to be transmitted per status report will be approx 30 higher compared with the data transmission without acknowledge mode On the other side this configuration ensures that no data will be lost during its transmission from the Telic Standard BC remote control unit to the control server GPS kilometer counter 0m lt Error Handling It exists a number of possible problems that might occur and that might prevent the Telic Standard BC remote control unit from fu
27. igured IP address The selection of the G PRS provider takes approx 1 minute as well as the log in process into the control center software This means that it takes 2 3 minutes after switching the device on until the first status report can be sent to the control center Independent of this delay the first G PS positions will be recorded and will be stored as status reports inside the device until they can be sent to the control center The first recorded G PS position will be used as a reference to find out if a new status report must be sent because the vehicle has moved more than x meters since the last transmission of a status report In addition a status report will be sent every time the vehicle changes its direction for more than x degrees compared with the direction reported with the last status report to the control center default 60 degrees Changes of a digital input cause the transmission of a status reportin any case If no actual GPS position is available the last known GPS position will be transmitted Each new status report sets a new reference point for distance calculations The Digital Inputs The Telic Standard BC remote control unit puts at your disposition 2 digital inputs To detect a signal as high logical 1 a voltage between 7 volts and 36 volts has to be put The input will recognized as low logical 0 if a voltage between 0 volts and 1 volt is put to the digital input If the input is not conn
28. matik amp Telemetrie Possible cause Solution The SIM card is blocked by the network provider Check if the SIM card is blocked You can do this by inserting the SIM card in your mobile phone and checking if it is then able to log in to the mobile network If itis able to do so attempt to send an SMS to somebody If you are able to do so then the SIM card is definitely not blocked Your pre paid SIM card is empty Re fill the pre paid SIM card Your pre paid SIM card is expired Pre paid cards usually expire when they are not regularly re filled often after 12 or 24 months If this is the case you must buy a new card The SIM card s PIN code was not changed to none or 0000 Remove the SIM card from the device and check the PIN code using a mobile phone The PIN code must be de activated or it must match with 0000 Please note thata PUK code is needed after three attempts to log in to a SIM card with a wrong PIN The SIM card is not properly inserted into the SIM card reader Make sure that the SIM card is properly inserted into the SIM card holder The device is unable to log in to the GPRS service Possible cause The GPRS service is notenabled for this SIM card Call your mobile phone network provider in order to check if the PRS service is enabled for this SIM card Page 43 Telic Telematik amp Telemetrie The device does not receive any GPS
29. nctioning properly This chapter is intended to help you to find out and to solve the most common problems Page 41 Possible Problems The device does not do anything Possible cause Telic Telematik amp Telemetrie Solution The ON 1 switch is setto 1 Switch on the ON 1 switch located besides the SIM card by sliding it to 0 I The unit is not connected correctly to your vehicle Please connect the unit to the vehicle according to the scheme in chapter Fifth Step Connecting the Unit to the On board power supply failure or defective fuse You cannot fix this problem yourself Instead please send the device to Telic for repair The device cannot connect to a GSM network Possible cause Solution The Telic Standard BC remote control unit is not within the range of GSM reception Check whether or not the GSM network is actually available at this location e g with a mobile phone and move to another place if no GSM signal is available The GSM antenna is not properly attached orthe antenna cable is defective Check to see if the GSM antenna is properly attached and if the cable of the antenna is damaged The SIM card in the device is new and is not yet activated Check to see if the SIM card is activated You can do this by inserting the SIM card in your mobile phone and checking if it is then able to log in to the mobile network Page 42 Telic Tele
30. ns that it can be used with standard AT modem commands to transmit data thru G PRS SMS data call etc to any 3 party server While the device is operated in GSM modem mode all functions regarding G PS vehicle tracking status reports etc are disabled 11 2 Switching from VTU Mode to the GSM modem Mode If you want to switch the device from VTU mode to the G SM modem mode you need to send the following AT command to the serial interface of the device AT E2APC 0 0 without the quotation marks After sending this command to the device you receive an answer as follows If you receive O K then the device has entered the G SM modem mode successfully and can now be operated with the AT commands for the WAVECO M G 564 GSM modem A description of the available AT commands can be ordered from Telic If you receive ERRO R then please try to enter SM modem mode again 11 2 2 Switching from GSM modem Mode to VTU Mode If you want to switch the device from the G SM modem mode to the VTU mode then please send to the serial interface of the device As an alternative you can also switch off and on the device with the small switch near to the SIM card holder 11 Other Features 12 1 Testing the Device After the installation of the device inside the vehicle we strongly recommend to verify the proper installation as follows Page 29 Telic Telematik amp Telemetrie 12 1 1 Verification of the LEDs
31. o Page 44 E 18 Telic Telematik amp Telemetrie Power consumption If you have read this user manual up to this point you have certainly realized that this little device can do a lot We have puta lot of effort into making its operation as simple as possible without limiting your possibilities This versatility unfortunately provides the following limitation If your vehicle is not used for more than one week we recommend that you disconnect the Telic Standard BC remote control unit or that you switch it off with the switch near the SIM card holder marked ON 1 because it may result in an empty car battery Alternatively you can mount the Telic Standard BC remote control unit so that it switches off as you remove the ignition key In addition itis good to know thatthe unit enters a sleep mode with low power consumption when the ignition is switched off Technical information Item Description Size 77 mm W x67 mm L x26 mm H Connectors 1 serial interface DSUB 9 female 1 FMEconnector for the GSM antenna 1 SMA connector for the G PS antenna 6 pin Molexl O connector Mini USB connector used only for production purposes LEDs 4 status LEDs to indicate the status of G PS G SM and power supply GSM GPRS Module Wavecom G S64 GPS Module u blox LEA 4A Backup Battery 610 mA h 3 7 volt Operating Temperature 20 C 60 C Power Supply 7volt 36 volt DC Housing Bl
32. power supply and power supply therefore activates power supply thru the built in backup battery The Speed Filter The Telic Standard BC remote control unit provides a filter that allows to block direction based status reports if the speed of the vehicle is lower than x Page 37 13 3 13 3 1 13 3 2 Telic Telematik amp Telemetrie km h Details regarding direction based status reports can be found in chapter 13 2 2 Direction based Status Reports Default value 6km h This filter can for ex be used in construction machines like cranes which turn around in the construction area during their normal work all the time In this case the information that the direction of the crane changed does not have any value for the dispatching centre On the other side it is very interesting for the dispatching centre to see that the machine is moving from one construction site to an other where it currently is and where it has been driving around The higher the configured value for the speed filter is the more behind a crossing the position report will be sent to the control server because the vehicle needs some time to exceed the speed limit that allows to send a direction based status report Information about some special Situations First Position of a new Route The first position of a new route is always the same like the last position of the former route If you switch off the device after a trip and yo
33. r counter is implemented into the software of the Telic Standard BC remote control unit This kilometer counter adds up short pieces of the distances of each driven route The calculation of these distances is based on GPS data Due to tolerances of the kilometer counter in the vehicle in combination with tolerances of the G PS information discrepancies between both values of up to 5 are normal The values of the PS based kilometer counter are transmitted with each status report to the control server The Telic Standard BC remote control unit provides the possibility to set the kilometer counter in the Telic Standard BC remote control unit with an SMS command This makes sense if for ex you mount the device in a vehicle which is not new and therefore in this moment reports a kilometer counter value gt zero The new value you want to setin the Telic Standard BC remote control unit must be expressed in meters not kilometers Example if you want to set the new value of the kilometer counter inside the Telic Page 35 Telic Telematik amp Telemetrie Standard BC remote control unit to 83213 789 km the SMS command must look as follows 0011008855 3213789 This command is composed as follows Value Description 00 Message ID a value of your choice between 00 and 99 11 Command code to change the configuration 008866 The last 6 digits of the serial number of the device can be found on the sticker of
34. rking time calculations will be more precise If the Telic Standard BC remote control unit is configured not to use the power save feature then the device can detect and report in this mode that it is moving e g if itis stolen or while a construction machine is transported on a truck even while ignition is off Page 15 5 6 5 1 2 Telic Telematik amp Telemetrie To operate the Telic Standard BC remote control unitin this mode the black wire must be connected to G RO UND pin 31 of the vehicle and the red wire must be connected to VCC pin 30 of the vehicle The brown wire must be connected to ignition pin 15 of the vehicle in this mode The device must be switched off when ignition is switched off This operating mode has the advantage that the device does not consume any power while the ignition is off This means that the battery of the vehicle cannot run out of energy which means that the vehicle will always be able to start its engine even after a few days without operation The disadvantage of this operating mode is that it takes the device longer to connect to the GSM network and it takes longer to find a new GPS position after igniton was switched from O FF to O N This means that for example working time calculations will be less precise In addition it can happen in this operating mode that short trips are not registered at all If the Telic Standard BC remote control unit is configured not
35. rveillance module A remote surveillance module is the combination of a compact computer system with various interfaces a G SM modem mobile phone without a keypad or display and a G PS receiver to receive satellite supported location information But what does G PS mean G PS means Global Positioning System O riginally this satellite tracking system was developed by the U S Military for its own purposes A GPS receiver is able to determine its position on the earth s surface and its height above sea level to within a few meters To accomplish this amazing feat 24 satellites ata height of 20 183 km continuously cross our planet in six different patterns They continuously send location data and time signals using an atomic clock G PS receivers simultaneously receive the signals of up to 12 satellites and compare the time of reception with their own built in clock Since the satellites operate at different distances from the receiver the signal delay indicates the distance of the various satellites to the remote surveillance module Using this difference the PS receiver is able to calculate its own position In order to transmit three dimensional results length height width the signals from at least four satellites are necessary Through the combination of the above technology the device can apprehend surveillance and control tasks and transfer them to a user via SMS or G PRS and all this for a price far less than
36. that of a laptop or a PDA with comparable functions Remote surveillance modules are available with or without satellite sup ported positioning With the Telic Standard BC remote control unit you have made the choice to use a device with satellite supported positioning Therefore aside from all of the surveillance possibilities of the device you can also find its precise location and react to changes in its position Operational Range The Telic Standard BC remote control unit is composed of two primary components a GPS module and a GSM module Page 8 5 3 5 4 Telic Telematik amp Telemetrie The GPS module receives signals from the G PS satellites which are operated by the U S Department of Defense These signals are available worldwide at every location However the precision of the positioning fluctuates A thorough introduction to GPS can be found in Chapter 5 4 Precision of the G PS Position on page 8 The GSM module is responsible for communication It is a cellular module working at850 MHz 900 MHz 1800 MHz 1900 MHz It functions properly anywhere in the world as long as G SM coverage is available Thus you can use your Telic Standard BC remote control unit anywhere where you can receive network signals on your mobile phone This means for you You will be able to locate your vehicle pretty much anywhere in the world distance under control What means GPRS GPS and GPRS are two different things
37. the choice if you want to use PIN code 0000 or if you want to de activate the PIN code Inserting the SIM card into the Telic Standard BC remote control unit is as easy as with your mobile phone e Put the device in front of you on the table as follows the slider of the SIM card cover must point to the ceiling and the three LEDs should be above the SIM card cover e Slide the SIM card cover carefully away from yourself towards the direction of the arrow between the two words O PEN Page 12 Telic Telematik amp Telemetrie e carefully flap the card reader upwards see picture e Now insert the SIM card into the SIM card holder so that the cut edge matches with the corresponding marking on the SIM card holder Asa result the gold contacts of the SIM card should face downwards e Flap the SIM card holder back into its original position and slide the lock back towards your body Page 13 Telic Telematik amp Telemetrie If you are not able to return the SIM card holder to its original position then you have not properly installed the SIM card With this step you have finished the SIM card installation 5 6 3 Third Step Replace the Cover Please slide the SIM card cover back into its original position Please ensure thatthe SIM card cover locks auditable 5 6 4 Fourth Step Connecting the Antennas The device is equipped with connectors for a cellular network antenna GSM antenna and a satellite
38. the device innri 13 parameters which are not going to be changed with this command 83213789 New value for the kilometer counter in meters 13 2 Strategies for Status Report Generation 13 2 1 Distance based status reports O ne of the key features of the device is to report information about routes a vehicle has driven based on the G PS information contained in each status report The default value for distance based status reports is 5 000 meters The device sends a new distance based status reportas soon as the distance between the last status report and the current position of the device straight line is more than x meters default 5 000 meters In reality the distance between two status reports is most likely significantly shorter because of the direction based status reports see chapter Direction based Status Reports In combination with direction based status reports the status reports of a typical route from one city to another looks as follows Frequent position reports atthe beginning of the trip while the vehicle is driving from an office building thru downtown to the entrance of the highway frequently turning left or right at crossings O n the highway position reports are pretty seldom because typically the highway is just a straight road which means that pretty no direction based status reports will be sent Page 36 13 2 2 13 2 3 13 2 4 Telic Telematik amp Telemetrie
39. ting the signal from several G PS satellites The more satellite signals it receives the greater the precision With a clear view of the sky up to 12 satellite signals can be received In order to receive a valid position a minimum of three satellite signals are necessary In an open field this is no problem If the vehicle is standing still precision of a meter and under can be achieved Unfortunately we are not always presented with such an ideal terrain In the city for instance several problems present themselves For example shading This means one or more satellites are blocked out by high buildings It is then perhaps the case that signals can only be received from some of the west north and south satellites but all of the east satellites are completely blocked This is also the case when the vehicle is stationary or parked by a building Another source of imprecision is reflections The signals sent out from the G PS satellites are radio signals which spread out in waves and which can be possibly reflected by for instance large metal surfaces Due to this reflection the G PS module may not receive the signal directly but rather reflected from another wall As a result the signal propagation delay is changed and a declination results In areas with high density and high buildings this can result in miscalculations of tens of meters A navigation system attempts to adjust for such problems by on the one hand taking into
40. tion is bad If you are going with your vehicle to an area with bad or even no GSM reception the unit buffers all status reports internally The unit will even keep this data if the power is switched off or the internal backup battery runs empty The buffer can keep up to 1000 position reports If more than 1000 status reports must be stored then the oldest status reports will be replaced The data will be sent to the control server as soon as the connection to a mobile phone network can be re established The oldest status report will be sent first While sending previously recorded status reports newly generated status reports will be sent immediately which means that sending the older status reports will be interrupted for a short while Reset of Telic Standard BC remote control unit If the external power supply is interrupted and therefore the internal backup battery runs empty after a while the Telic Standard BC remote control unit will be shut off completely Despite the fact that no more power is available for the device all settings and all buffered data will be kept and used again as soon as external power is available again The integrated Watchdog The Telic Standard BC remote control unit comes with an integrated watchdog Page 32 13 Telic Telematik amp Telemetrie This watchdog is independent of the rest of the electronics in the unit It surveys the proper function of the program inside the G SM module an
41. to use the power save feature then the device can detect and report in this mode that it is moving e g if itis stolen or while a construction machine is transported on a truck even while ignition is off but only as long as the internal backup battery can provide enough energy typically a few hours Ca hide pin 31 Tat ITION vehide pin 15 To operate the Telic Standard BC remote control unit in this mode the black wire must be connected to GROUND pin 31 of the vehicle and the red wire and the brown wire must be connected to IGNITION pin 15 of the vehicle Page 16 Telic Telematik amp Telemetrie The brown wire must be connected to ignition pin 15 of the vehicle in this mode Even if you connect the device according to the above mentioned scheme to the cigarette lighter and if the cigarette lighter is switched on and off together with the IG NITION which is the case in most vehicles the routes driven by the vehicle will be reported correctly 5 6 5 1 3 Fuses The device contains internal fuses to protect it against high voltage and wrong connection to the vehicle If these fuses are damaged which can hardly occur in a 12 volt 24 volt vehicle then you need to send the device to your supplier for repair You cannot repair the fuses yourself 5 6 5 2 Digital Input 1 The Digital Input 1 can be connected to any signal which reports O N or O FF The input can be used with a voltage up to 36
42. u switch it on at an other place later control server will report the last position of the former route as the first position of the new route which is not the case in reality and which can cause a mistake in the calculation of the kilometer counter Therefore we do not recommend switching the device off while taking it from one place to another Last Position of a new Route As soon asthe ignition is switched off atthe end of a new route the current G PS position will be stored in the Telic Standard BC remote control unit in a special memory that even remembers this information if the device runs out of battery power When the device is restarted later this last G PS position will be read from the memory and will be sentto the control server as soon as G PS delivers a valid timestamp It can take several minutes to receive valid time information from the G PS receiver if it was switched off before without power supply Page 38 Telic Telematik amp Telemetrie 14 Quick Start 14 1 Hardware Installation e Ask your mobile phone network provider to activate GPRS on your SIM card De activate the PIN of the SIM card with a standard mobile phone e Insert the SIM card into the unit To do so the small square on the top of the unit must be opened e Mount the unit in your vehicle Connectthe combined antenna with both cables to the unit The antenna should have free view to the sky o Connect the cables for power supply red
Download Pdf Manuals
Related Search