Operating Instruction
Contents
1. centre pin of the 3 5 mm socket Otherwise use only the supplied AC power adaptor Be sure to disconnect the AC power adaptor when the unit is not in use FUNCTION OF CONTROLS S7 OPEN Button OPEN For opening the CD tray to insert or remove a CD Pil PLAY PAUSE Button pj Press Pll button to begin playing Press pI button to pause during play To release pause press p gt button again E STOP Button Hj To activate stop mode standby mode from playing mode In standby mode press J button again the unit will be off SKIP SKIP TUNING Button TUNING Press SKIP TUNING lightly repeatedly To locate the beginning of the current selection or previous selections or tune into a station in Radio status Keep SKIP TUNING depressed To go back at high speed or auto search a station in Radio status SKIP SKIP TUNING Button TUNING Press SKIP TUNING lightly repeatedly To locate the beginning of next selections or tune into a station in Radio status Keep SKIP TUNING depressed To go ahead at high speed or auto search a station in Radio status PLAY MODE PLAY MODE STEREO Button STEREO Press PLAY MODE STEREO button to select the various playing modes during CD playback Press PLAY MODE STEREO button to select the stereo function during listen to the radio PROGRAM PROGRAM MEMORY Button MEMORY Press PROGRAM MEMORY button to reserve songs while playing a CD or store stations in2. edge to avoid finger prints on its surface Do not stick paper or tape or write anything on the surface SPECIFICATIONS 2 AA size LR6 or UM 3 alkaline batteries or DC IN 6V 350mA power adaptor Polarity of plug O Power requirements Operating voltage U S A Canada 120V AC 5 AC adaptor 60 Hz Middle East and Australia 240V AC 5 50 Hz UK and Germany 230V AC 5 50Hz Chile 230V AC 5 50 Hz Singapore Malaysia amp Thailand 200 240V AC 5 50 Hz Japan 100V AC 5 50 60Hz Design and specifications are subject to change without notice Printed in CHINA 811 821691 040
3. not operate In this case remove the disc and leave the unit in a warm place for several hours until the moisture evaporates e For the unit to operate at its best it should not be subject to temperatures below 5 C 41 F or above 35 C 95 F Notes on headphones earphones Do not use headphones earphones while driving cycling or operating any motorized vehicle it may create a traffic hazard and is illegal in some areas It can also be potentially dangerous to play your headsets at high volume while walking especially at pedestrian crossings You should exercise extreme caution or discontinue use in potentially hazardous situations Avoid using headphones earphones at high volume Hearing experts advise against continuous loud and extended play If you experience a ringing in your ears reduce volume or discontinue use Keep the volume at a moderate level This will allow you to hear outside sounds and to be considerate to the people around you If you have any questions or problems concerning your unit please consult your nearest dealer NOTES e This unit can play Audio Discs including CD Recordables and CD Rewriteables Do not try to play CD ROMs CD Is CDVs or computer CDs e The unit may not play a CD R RW disc that is recorded on personal computers or some kinds of CD R RW recorders be cause of differences in recording platforms e Donotattach any seal or label to either side the recordable side or the labled
4. NTRO play 3 Press PLAY MODE STEREO button to cease the INTRO play and continue playback in the NORMAL play mode INTRO play always starts from the first track SHUFF Shuffle Play Playing the Selections in Random Order 1 Press PLAY MODE STEREO ge button during play until SHUFF Va PAIN flashes in the display window MM I arr 2 Press pi to begin the SHUFF play y To locate the beginning of the track Pre AITA being played press SKIP I ar on TUNING BA oA ote Coo Tolocate the nexttrack press SKIP TUNING However you cannot locate a previous track even if you press SKIP TUNING PGM Program Play Playing the Selections in the Desired Order 1 Press PROGRAM MEMORY button until PGM flashes and Ann appears in the display window 2 Press SKIP TUNING or SKIP TUNING button to select the desired selection 3 Press PROGRAM MEMORY button to store this track in memory 4 To add additional track s repeat steps 2 and 3 5 Press Pll PGM stops flashing and play starts To Edit Program Play To check Press PROGRAM MEMORY button lightly during programming before you press pi Each time PROGRAM MEMORY button is pressed the track number appears in the display window To change When checking press either SKIP TUNING or SKIP TUNING button to alter the track number for the pro
5. Portable Radio CD Player Operating Instruction Before operating the unit please read this manual thoroughly and retain it for future reference WARNING To prevent fire or shock hazard do not expose the unit to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only CAUTION The use of optical instruments with this product will increase eye hazard INFORMATION For the Customers in U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet that is on a circuit different from the one the rece
6. The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance 9 Grounding or Polarization Precautions should be taken so that the grounding or polarization means of an appliance are not defeated 10 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance 11 Cleaning The appliance should be cleaned only as recommended by the manufacturer 12 Nonuse Periods The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time 13 Object and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings 14 Damage Requiring Service The appliance should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged or B Objects have fallen or liquid has been spilled into the appliance or C The appliance has been exposed to rain or D The appliance does not appear to operate normally or exhibits a marked change in performance or E The appliance has been dropped or the enclosure damaged 15 Servicing The user should not attempt to service the appliance beyond that described in the oper
7. ating instructions All other servicing should be referred to qualified service personnel POWER SOURCES Using with Batteries Insert two AA size batteries LR6 or UM 3 alkaline according to the and indications in the battery compartment Inserting batteries Open the CD door by pushing the clasp Detach the battery cover on the middle cabinet and insert two AA size batteries LR6 or UM 3 alkaline Notes on batteries Insert batteries with correct polarity Do not use old batteries together with new ones or different types of batteries together If the electrolyte inside the battery should leak wipe the contaminated parts in the battery compartment with a cloth and replace the old batteries with new ones When the unit is not to be used for a long period of time remove the batteries Do not mix ALKALINE standard CARBON ZINC or rechargeable NICKEL CADMIUM batteries Notes on wah When the battery voltage level is low maak will flash 10 15 minutes playback still continues in this period e Playback will automatically come to a stop when the batteries have no more power Do not repeat pressing 4i as the unit may operate incorrectly Replace all the batteries with new ones wap will not be on if an AC adaptor is used Using on house current If the unit you purchased does not include an AC power adaptor please use a 6V 350mA AC power adaptor Plus pole to the
8. ersist after you have made the following checks consult your nearest service facility Disc play does not start e The disc is inserted upside down or incorrectly Insert the disc correctly with the label surface up Dusty or defective disc Dirty or dusty lens The disc compartment lid is not closed Moisture condensation gt Leave the unit in a warm place until the moisture evaporates The AC power adaptor is not plugged into the wall outlet The unit is not placed on a level surface Weak batteries No sound from the headsets The headphones earphones plug is not firmly connected to the PHONES jack Adjust the VOL control Dirty plug Skipping of sound e Dirty or defective disc Dirty lens Strong vibration When using with batteries the battery life is short e Use alkaline batteries and not manganese batteries The unit can not be operated e No disc dirty disc or scratched disc The unit will return to full stop mode after approx 30 seconds or reset the player by pressing W once and then insert a disc to start playing MAINTENANCE Cleaning the unit Do not use volatile chemicals on this unit Clean by lightly wiping with a soft cloth Cleaning CD If the CD skips or will not play the disc may need to be cleaned Before playing wipe the disc in a circular motion from the centre out with a cleaning cloth After playing store the disc in its case Handling the disc Only touch the CD on the
9. gram currently displayed Press PROGRAM MEMORY button to register the newly selected track into memory To delete When open the CD door including that program will be cancelled Notes Repeat play intro play can be performed during program PGM play cannot be set in SHUFF play mode The program is also erased when the disc compartment is opened or the auto power off function turns the power off Ifthe program mode is exited by means of the gg button all the programs would still remain in memory During the program play the AMS operates in the programed order AMS auto music sensor DIGITAL ANTI SHOCK SYSTEM The Digital Anti Shock System incorporates a special electronic circuit that prevents sound from skipping when the unit is subject to shocks and vibration during play When the unit receives a physical shock which prevents the laser pick up from reading the CD this system immediately starts playing the sound stored in its memory and continues until the laser pick up recovers If the unit is subject to continuous shocks and all the data stored in memory is used up the sound will skip If the vibration stops then the data memory will be restored To reset the CD player press gp once Note Under some conditions noise may be heard or sound skipping may occur when the disc is dirty or scratched when the disc contains certain signals TROUBLESHOOTING GUIDE Should any problem p
10. iver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment For the Customers in the United Kingdom European Countries This Compact Disc player is classified as a CLASS 1 LASER product The CLASS LASER PROD UCT label is located on the bottom exterior CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1 PRODUCTO LASER DE CLASE 1 PRODUTO LASER CLASSE 1 For the Customers in Canada This apparatus complies with the Class B limits for radio noise emissions set out in radio interference regulations CAUTION This product INVISIBLE LASER RADIATION WHEN OPEN AND contains a INTERLOCKS DEFEATED low power AVOID EXPOSURE TO BEAMJ laser device PRECAUTIONS On Safety As the laser beam used in this compact disc player may be harmful to the eyes do not attempt to disassemble the casing Refer servicing to qualified personnel only Do not put any foreign objects in the safety slot inside the disc compartment If you do so the laser beam may come out when the lid is opened Do not put any foreign objects in the DC IN 6V external power input jack Should any solid objects or liquid fall into the unit disconnect the power supply and have the unit checked by qualified personnel before operating it any further On Operation Since the CD sy
11. mode The unit will return to full stop mode automatically after approximately 30 seconds if no button is pressed During Pause The current track time flashes Pause mode of the first track When no disc is inserted into the player and when l is pressed the display window shows gis and The unit cannot be operated when no disc message is displayed After approx 30 seconds the unit will return to full stop mode or reset the player by pressing gj once and then insert a disc to start playing VARIOUS PLAYING MODES During playback every time the PLAY MODE STEREO button is pressed the mode will change to the next one as follows NORMAL play gt lt J Repeat One gt Z5 att Repeat ALL gt INTRO gt SHUFF Normal Play Playing the Whole Disc The CD is played once from beginning to end Repeat Playback Repeat One and Repeat All e To repeat the same track press PLAY MODE STEREO button during play until lt 5 appears in the display window Select desired track to be played repeatedly by pressing SKIP TUNING or SKIP TUNING e To repeat the whole disc Press PLAY MODE STEREO button during play until lt ALL appears in the display window Intro Play Playing the First Ten Seconds of All the Selections 1 Press PLAY MODE STEREO button during play until INTRO flashes in the display window 2 Press pj to begin the I
12. n 3 Press PROGRAM MEMORY button till PGM flashes in the display window 4 Press PRESET UP or PRESET DOWN button to select the desired number 5 Press PROGRAM MEMORY button to store the station 6 Repeat steps 2 to 5 to preset other stations Tuning Into a Preset Station Press the PRESET UP or PRESET DOWN button repeatedly to select the desired preset station For Better Reception FM To improve FM reception extend the earphone cord AM To improve AM reception rotate the unit Note e During listen to the radio you can press PLAY MODE STEREO button to select stereo broadcast While the reception is good the ST icon will appear in the display window DISC PLAYING Open the CD door by sliding the OPEN button 2 Insert the CD with the printed side facing upwards and push the disc gently until it clicks so that the disc fits into the pivot 3 Press the CD door to close 4 Press the I button to play CD Note To play an 8 cm 3 inch disc you can play it without an adaptor On Display Window When you press l the display window shows N During Playback The track number of the current selection appears When W is pressed during playback total number of tracks on the disc will be displayed and the unit is in standby mode If gy is pressed again the unit will return to full stop mode If py is pressed the unit returns to play
13. radio mode BAND BAND TUNER ON Button TUNER ON Press BAND TUNER ON button to select the AM or FM band and listen to the radio PHONES PHONES Jack For connecting the headphones earphones oeo Mains Socket DC in 6V DC IN 6V VOL tm Volume Control To adjust the volume PRESET UP PRESET UP DOWN Buttons PRESETDOWN Select presetted stations Only available in radio mode LISTENING TO THE RADIO 1 Press BAND TUNER ON button to turn on the Radio 2 Press SKIP TUNING or SKIP TUNING button to tune into a station To Tune Faster Hold down the SKIP TUNING or SKIP TUNING button While the button is being held the frequency will change faster To Search for a Station Quickly AUTO Search Keep the SKIP TUNING or SKIP TUNING button pressed until the tuner starts searching for a station After tuning into a station the search stops To stop the Auto Search manually press the SKIP TUNING or SKIP TUNING button The Auto Search may not stop at stations with very weak signals To Turn Off the RADIO Press J button to turn off the Radio Presetting RADIO Station You can tune into a stored station directly by entering the preset number e 10 stations on AM band can be presetted e 20 stations on FM band can be presetted 1 Press BAND TUNER ON button to select AM or FM band to listen to the Radio 2 Press SKIP TUNING or SKIP TUNING button to tune your desired statio
14. side of a CD R RW disc It may cause malfunction e Do not use irregular shape CDs example heart shaped oc tagonal ones It may result in malfunction e When a CD RW is loaded it takes about 15 seconds before it can be play back IMPORTANT SAFETY INSTRUCTIONS 1 Read Instructions All the safety and operating instructions should be read before the appliance is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to 4 Follow Instructions All operating and use instructions should be followed 5 Water and Moisture The appliance should not be used near water for example near a bathtub washbowIl kitchen sink laundry tub in a wet basement or near a swimming pool and the like 6 Ventilation The appliance should be situated so that its location or position does not interfere with its proper ventilation For example the appliance should not be situated on a bed sofa rug or similar surface that may block the ventilation openings or placed in a built in installation such as a book case or cabinet that may impede the flow of air through the ventilation openings 7 Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat 8 Power Sources
15. stem offers a wide dynamic range the peaks of the high level inputs are recorded with high fidelity and the noise level is very low Do not turn up the volume while listening to a part of the disc with no audio signals or very low level inputs If you do the speakers may be damaged when the peak level of the sound is played The lens on the disc table should be kept clean Do not touch the lens or poke at it If you do the lens may be damaged and the unit will not operate properly Notes One alternative method to resolve the failure is to add the following instruction to the user manual The normal function of the product may be disturbed by interference and shows error message just re connect the power source for resume normal operation On Installation e Never install the unit where it would be subject to heat sources such as radiators or airducts direct sunlight excessive dust moisture or rain mechanical vibration or shock unleveled surface Donot place any heavy object on the top of the unit When the unit is used with an AC power adaptor do not wrap the unit in a cloth blanket etc If you do the temperature inside and outside the unit may rise considerably resulting in malfunctioning of the unit or serious accidents e Ifthe unit is brought directly from a cold to a warm location or is placed in a very damp room moisture may condense on the lens inside the unit Should this occur the unit will
Download Pdf Manuals
Related Search