UV COB Cannon
Contents
1.2. ue Sd Tine Ramp Effect Unit Dim Mode Tup ns uv Standard dr 0 0 0 Stage dr 1 1540 1660 TV dr 2 1860 1940 Architectural dr 3 2040 2120 Theatre dr 4 2230 2280 ADJ Products LLC www adj com UV COB Cannon User Manual Page 11 UV COB Cannon The UV COB Cannon is fully operational in three different mounting positions hanging upside down from a ceiling hanging sideways on trussing or set on a flat level surface The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the units weight Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp Installation UV COB Cannon Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 3 fixtures maximum for 120V and 5 fixtures maxi mum for 240V After the maximum fixtures has been reached you will need to use a new power outlet They must be the same fix tures DO NOT mix fixtures
3. Pacific Standard Time Voice 323 582 3322 Fax 323 582 3108 E mail support AmericanDJ com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com UV COB Cannon User Manual Page 2 UV COB Cannon General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference UV COB Cannon Features 3 Operating Modes Sound Active Manual Mode amp DMX Control Electronic Dimming 0 100 Built in Microphone e DMX 512 protocol 3 Pin DMX Connection e 3 DMX Modes 1 Channel Mode 2 Channel Mode and 3 Channel Mode 5 Selectable Dimmer Curves e Power Cord Daisy Chain See page 12 UV COB Cannon Warranty Registration The UV COB Cannon carries a 2 year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whethe
4. ADJ Products LLC www adj com UV COB Cannon User Manual Page 12 UV COB Cannon Disconnect the unit from its power source Remove the power cord from the unit Once the cord has been removed you will find that the fuse holder is located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder also has a holder for a spare fuse Fuse Replacement UV COB Cannon Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew UV COB Cannon Trouble Shooting Listed below are a few common problems the user may encounter with solutions Cleaning Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound 1
5. Quiet or high pitched sounds will not activate the unit 2 Make sure that Sound Active mode is activated ADJ Products LLC www adj com UV COB Cannon User Manual Page 13 UV COB Cannon Model UV COB Cannon Voltage 100V 240V 50 60Hz LEDs 100W COB UV LED Beam Angle 33 Degrees Working Position Any safe working position Specifications Power Consumption 120W Power Cord Daisy Chain 3 Fixtures Max 120V 5 Fixtures Max 240V Fuse 3 15 Amp or 4 Amp Weight 111bs 4 98Kgs Dimensions 12 75 L x 11 W x 8 H 320 x 278 x 200mm Colors UV DMX Channels 3 DMX Modes 1 Channel Mode 2 Channel Mode amp 3 Channel Mode Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com UV COB Cannon User Manual Page 14 UV COB Cannon ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On Ri PA facebook com americandj twitter com americandj youtube com adjlighting
6. XLR connections to any standard DMX control ler 5 Please see page 10 for DMX values and traits ADJ Products LLC www adj com UV COB Cannon User Manual Page 7 UV COB Cannon Operating Instructions UV Manual Dimmer Mode 1 Plug the fixture in and press the MODE button until 2 When XXX4 is displayed you are in dimming mode Press the UP and DOWN buttons to adjust intensity 3 When XXX5 is displayed you are in strobing mode Press the UP and DOWN buttons to adjust strobing 4 When XXX6 is displayed you are in dimmer curve adjustment Press the UP and DOWN buttons to scroll through the different curve modes See the dimmer curve chart on page 11 Sound Active Mode In this mode the UV COB Cannon will react to sound and chase through the different colors 1 2 3 Plug the fixture in and press the MODE button until 0017 is dis played The fixture will now change via sound Press the UP or DOWN button so that 0027 is displayed This is sound sensitivity adjustment Use the UP and DOWN buttons to adjust the sensitivity ADJ Products LLC www adj com UV COB Cannon User Manual Page 8 UV COB Cannon Master Slave Configuration Master Slave Configuration This function will allows you to link units together to run in a Master Slave mode In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units built in programs Any
7. the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems gt and interference It is always advisable gt is to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Notes TT ADJ Products LLC www adj com UV COB Cannon User Manual Page 6 UV COB Cannon Operating Instructions LED Display On Off To set the LED display to turn off after 10 seconds press the MODE button until either 0010 or 0020 is displayed Press the UP or DOWN buttons to toggle between the two modes Press SAVE once
8. you have found your desired mode To set the display press the MODE button until 0010 LED display on at all times 0020 LED display shuts off after 10 seconds Operating Modes The UV COB Cannon has three operating modes DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller UV Dimmer Mode Adjust the intensity of UV output You can also apply strobing in this mode and select a dimmer curve e Sound Active mode The unit will react to sound chasing through the built in programs DMX Mode Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs The UV COB Cannon has 3 DMX modes 1 Channel mode 2 Channel mode and a 3 Channel mode See page 10 for each DMX traits 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller 2 To select your desired Channel mode press the MODE button until e To run the 1 Channel Mode press the MODE button until XXX1 is displayed This is the 1 Channel DMX Mode e To run the 2 Channel Mode press the MODE button until XXX2 is displayed This is the 2 Channel DMX Mode e To run the 3 Channel Mode press the MODE button until XXX3 is displayed This is the 3 Channel DMX Mode 3 After you have chosen your desired DMX Channel mode plug in the fixture via the
9. 7 for the dif ferent modes The DMX address is set on the back panel of the UV COB Cannon Your unit and your DMX controller require a standard 3 pin XLR connector for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Figure 1 Notice Be sure to follow figures two and three when making your own ADJ Products LLC www adj com UV COB Cannon User Manual Page 5 UV COB Cannon Set Up cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 Se te see see set ese oeet asec seeess I I gt XLR Male Socket ACR Female SECRET XLR Pin Configuration I I eS 1 1 Ground I i 2 Cold 2 Cold 1 Ground Pin 1 Ground I I i i Pin 2 Data Compliment negative I I I I I I Pin 3 Data True positive Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on
10. UV COB Cannon Rev 4 14 ADS NA User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent assembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipmen
11. ith this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA QUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The UV COB Cannon can be controlled via DMX 512 protocol The UV COB Cannon has 3 DMX channel modes please see page
12. r under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper included in the shipping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by contacting our customer support team on our customer support number All pack ages returned to the service department not displaying a R A number on the outside of the package will be returned to the shipper ADJ Products LLC www adj com UV COB Cannon User Manual Page 3 UV COB Cannon Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed e Never plug this unit in to a dimmer pack Always be sure to mount this uni
13. t from power when not in use Thank you UV COB Cannon Introduction Unpacking Thank you for purchasing the UV COB Cannon by ADJ Products LLC Every UV COB Cannon has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during ship ping If the carton appears to be damaged carefully inspect your fix ture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The ADJ UV COB Cannon is part of a continuing pur suit to create high quality intelligent lighting The UV COB Cannon is a DMX intelligent high powered LED par fixture This fixture can be used in a stand alone mode or connected in a Master Slave configuration This wash has six operating modes Sound Active mode Auto mode Fade mode White Preset Mode Color Temperature mode and DMX control mode Customer Support ADJ Products LLC provides a customer sup port line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or sugges tions Service Hours are Monday through Friday 8 00 a m to 4 30 p m
14. t in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit e Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 13 for cleaning details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com UV COB Cannon User Manual Page 4 UV COB Cannon Set Up Power Supply The ADJ UV COB Cannon contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source W
15. unit can act as a Master or as a Slave however only one unit can be pro grammed to act as the Master Master Slave Connections and Settings 1 Daisy chain your units via the XLR connector on the rear of the unit Use standard XLR data cables to link your units together Remember that the Male XLR connector is the input and the Female XLR con nector is the ouput The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only On the Master unit press the MODE button until 0018 is dis played This is the Master setting press the SAVE button After you have set it to the Master setting set your desired operating mode For the Slave unit press the UP or DOWN button so that 0028 is displayed This is the Slave setting press the SAVE button Now connect the Slave unit to the Master unit using the XLR con nections ADJ Products LLC www adj com UV COB Cannon User Manual Page 9 UV COB Cannon 1 Channel Mode DIMMING 0 100 DIMMING 0 100 STROBING SLOW FAST 1 259 0 100 li dee 1 259 SLOW FAST DIMMER CURVES STANDARD STAGE TV ARCHITECTURAL THEATRE DELAY MODE CONTROL ADJ Products LLC www adj com UV COB Cannon User Manual Page 10 UV COB Cannon Dimmer Curve Chart Dimmer 100 50 DR Me 0 Tup Tdown ms
Download Pdf Manuals
Related Search