CBH Advanced systems
Contents
1. Please observe that the actuators LA27 used for CBH Advanced systems are with Hall sensor and are not compatible with CBH Basic systems Please observe that if you use the SMPS001 or SMPS002 the CBH Advanced must be configured first as the CBH Advanced is standard set to 29V DC This is done via the CBH configurator BA001 will not be charged It is possible only to use 1 power supply SMPS001 SMPS002 or SMPS006 for 2 CBH systems Remember speed may decrease when running 2 systems at the same time Page 7 of 28 Before installation re installation or troubleshooting e Stop the actuators e Pull out the mains plug e Relieve the actuators of any loads which may be released during the work Before start up e Make sure that the system has been installed as instructed in this User Manual e Make sure that the voltage of the control box SMPS Is correct before the system is connected to the mains e System connection The individual parts must be connected before the control box SMPS is connected to the mains See the User Manual for LINAK actuators if necessary During operation e f the control box makes unusual noise or smells switch off the mains voltage immediately e Take care that the cables are not damaged e he products must only be used in an environment that corresponds to their IP protection Misc The actuator system has a sound level below 70dB A in typical applications Updated manuals and declara2. Intertek RECOGNIZED COMPONENT Intertek RECOGNIZED COMPONENT TERT Intertek RECOGNIZED COMPONENT Intertek RECOGNIZED COMPONENT Intertek C N 120690 Conforms to UL962 Cert to CSA Std C22 2 No 68 09 ETL Recognized Component mark for Canada and United States C N 9901916 Conforms to UL962 Cert to CSA Std C22 2 No 68 09 ETL Recognized Component mark for Canada and United States C N 4008003 Conforms to UL962 Cert to CSA Std C22 2 No 68 09 ETL Recognized Component mark for Canada and United States C N 4008005 Conforms to UL962 Cert to CSA Std C22 2 No 68 09 ETL Recognized Component mark for Canada and United States C N 4008671 Conforms to UL962 Cert to CSA Std C22 2 No 68 09 ETL Recognized Component mark for Canada and United States C N 4009507 Conforms to UL962 Cert to CSA Std No 68 09 ETL Recognized Component mark for Canada and United States Page 12 of 28 Description of the HOMELINE CBH Advanced system A typically CBH Advanced system consists of CBH Advanced control box SMPS001 SMPSOO2 or SMPS006 power supply LA27 linear actuator HB20 or HC20 handset 2 Massage motors Lightplug Mounting guidelines for the CBH The control box is to be fastened with 2 screws with a head diameter between 8 and e 10 mm With regard to the surface pressure 10 mm is preferable See drawing for placing of mounting holes and the space the CBH takes up The
3. Massage motor MD1 HB20RF Hand Control HC20RF Hand Control Page 22 of 28 LED Lightbox DC Connector USB Connector Lightplug LL 2 U A LINAJK LIGHTPLUGOO Soe aia AG CT Page 24 of 28 BAOO1 standby power OW LINAK APPLICATION POLICY The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as hardware software technical advice etc related to an existing or new customer application LINAK products as defined above are applicable for a wide range of applications within the Medical Furniture Desk and Indus
4. PIN 3002001 Ver XXX CO CE n CIN1234567 TIR P 0 1234567 0001 A Assembled in XX YY Label for HB22RF Label for HC20RF LINAK 53 0077017 Ver 1 08 LINAK EJ A LTZ S FOLE E MTS 0077036 Ver 1 03 HC23RF0020 D HB22RF 1000 DCER FCC ID XBE HB2XRFXXXX Label for LED Lightbox LEDLIGHTBOX001 Date 2009 11 10 LINAK NOT TO BEOPENEDBY UNAUTHORIZED PERSONNEL Ge 1234567 gt ABS lt AK Label for DC Connector DCCONNECTOR001 LINAK IS Date 2000 11 10 SEGURO U Out 2 24V Max 0 5 Amp NOTTO BE OPENEDBY UNAUTHORIZED PERSONNEL oce 1234567 gt ABS lt ADE Label for USB Connector USBCONNECTOR001 LINAK E Date 2009 11 10 WE IMPROVE YOUR LIFE U Out 5V Max 0 5 Amp NOT TID BEOPENEDBY UNAUTHORZER PERSONNEL amp cc amp 1234567 gt ABS lt AGE Label for LA27 LINAK 53 WE IMPROVE YOUR LIFE Item No 273100A01405040 Prod Date 2009 03 18 S 0 7654321 Max Load Push 1500N IPX4 A Power Rate 24 V Max 3 5 A zu Cycle Max 10 TO BE OPENED BY UNAUTHORIZED PERSONNEL NUN eR P 0 123456 0001 MADE BY LINAK A S DENMARK Label for Massage Motor E Item No MD1000D1 Prod Date W22 2008 w g Power Rate Max 24m Max0SAmp O c Duty Cycle 10 Max 30 min 2 NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL gt P 0 123456 0001 MADE IN ITALY Label for SMPS001 LINAK Sj WE IMPROVE YOUR LIFE Type Power Supply item No SMPS001 input 230 240V 5
5. mounting surface to which the control box is attached should have a surface evenness better than 0 5 mm The mounting screws on the control box must be fastened with a max torque of 1 Nm The CBH must not be packed in heat insulating material but must be placed so that it can emit waste heat to the surroundings There are no ventilation holes to consider the CBH emits heat through its surface The electric connection The system is to be connected as follows e Each linear actuator must be connected to the socket on the control box by means of the motor cable which has a 6 pin plug in each end e Connect any accessory e Connect the SMPS unit to the CBH via a DC port and switch on the mains e Finally set up the wireless handset to the CBH by pressing the small set up button on the CBH keeping it down while pressing a random button on the handset e s Please note that the control box SMPS must only be connected to the voltage stated on the labels The LA27 actuator is a powerful actuator designed for applications such as leisure beds Mechanical spline The splines function so that the actuator can only push not pull During pull in the actuator the inner tube is lifted off the thread bush and the actuator can therefore never pull a load only push Functional test of mechanical splines When the piston rod is at the innermost position it must be possible to pull it out manually to its full travel length and to press it in agai
6. 0Hz 1 2A Output 24V 2A Model No ASW0539 24020002A Serial No CY1227 ZN NOT TO BE OPENED BY UNAUTHORIZED G X I 6 Label for SMPS006 LINAK ES WE IMPROVE YOUR LIFE Type Power Supply Item No SMPS006 Input 100 240V 50 60Hz 1 6A Output 29V Model No ASW0552 29020002B Serial No P0 667734CY141030 Int 10 max 6A 2min 18 min A CAUTION e Risk of electric shock e For indoor use only e Do not open the unit e Dry location use only A gt n O CE CLASS 2 POWER SUPPLY Made In China Made In China Label for SMPSOO2 LINAK E WE IMPROVE YOUR LIFE Type Power Supply Item No SMPS002 0 X Input 120V 60Hz 1 2A dka Output 24V Model No ASW0551 24020002A Serial No PO 632312 CY140401 NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL 3JXT C US E308336 fe LIST 4552 POWER SUPPLY Made In China Page 17 of 28 DRAWING APPENDIX CBH Advanced SMPS001 OW standby power SMPS002 OW standby power Page 19 of 28 SMPS006 standby power Page 20 of 28 LA27 I mA Drawing no LA27001B
7. 1 36 34 34 Fax 33 0 2 41 36 35 00 E mail linak linak fr www linak fr GERMANY LINAK GmbH Phone 49 6043 9655 0 Fax 49 6043 9655 60 E mail info linak de www linak de INDIA LINAK A S India Liaison Office Phone 91 120 4393335 Fax 91 120 4273708 E mail infoGlinak in www linak in IRELAND LINAK UK Limited Ireland Phone 44 0 121 544 2211 Fax 44 0 121 544 2552 44 0 796 855 1606 UK Mobile SLOVAKIA LINAK Slovakia s r o Phone 421 51 75 63 414 Fax 421 51 75 63 410 E mail jp linak sk www linak com ITALY LINAK Italia S r l Phone 39 02 48 46 33 66 Fax 39 02 48 46 82 52 E mail infoGlinak it www linak it JAPAN LINAK K K Phone 81 45 533 0802 Fax 81 45 533 0803 E mail linak linak jp www linak jp MALAYSIA LINAK Actuators Sdn Bhd Phone 60 4 210 6500 Fax 60 4 226 8901 E mail infoGlinak asia com www linak my NETHERLANDS LINAK Actuator Systems B V Phone 31 76 5 42 44 40 Fax 31 76 5 42 61 10 E mail infoGlinak nl www linak nl NEW ZEALAND LINAK New Zealand Ltd Phone 64 9580 2071 Fax 64 9580 2072 E mail nzsales linak com au www linak co nz 35 387 634 6554 Republic Of Ireland Mobile E mail salesQlinak co uk www linak co uk IRAN Bod Inc Phone 98 2188998635 6 Fax 98 2188954481 E mail info bod ir www bod ir RUSSIAN FEDERATION 000 FAM Phone 7 812 3319333 Fax 7 812 3271454 E mail purchase fam drive ru www fa
8. AK systems are high tech products based on many years of experience in the manufacture and development of actuators electric control boxes controls and chargers This User Manual does not address the end user It is intended as a source of information for the manufacturer of the equipment or system only and it will tell you how to install use and maintain your LINAK electronics It is the responsibility of the manufacturer of the end use product to provide a User Manual where relevant safety information from this manual is passed on to the end user We are sure that your LINAK product system will give you many years of problem free operation Before our products leave the factory they undergo full function and quality testing Should you nevertheless experience problems with your LINAK product system you are always welcome to contact your local dealer LINAK subsidiaries and some distributors situated all over the world have authorised service centres which are always ready to help you LINAK provides a warranty on all its products This warranty however is subject to correct use in accordance with the specifications maintenance being done correctly and any repairs being carried out at a service centre which is authorised to repair LINAK products Changes in installation and use of LINAK products systems can affect their operation and durability The products are not to be opened by unauthorised personnel The User Manual has been writt
9. R HOMELINE IMPROVING COMFORT CBH Advanced systems LINAK WE IMPROVE YOUR LIFE To learn more about LINAK please visit Page 1 of 28 Page 2 of 28 Contents PEE AE e ea NAA RO O A AA MM EP AN 4 APA IP n 5 Important information i4 a NAGIGING KGABI ING unc RT ERE NEM OM a ocu t LG RE ERES Rae RERO EE EHUE 6 euis MINIS MI OI sc EE o E PK 6 ecu TS c 7 Before installation re installation or troubleshooting 8 Before Start Up occccccccisiacsnccsscesteascecscencscereececsbnenndadseeesnaueasecsabenedeeestadcsbbdecsssseassegeendedseesesdeerssdsccesseasasamecncadenaeeun 8 Repais aa A AA MD E S MEE 10 Manufacturer s declaration trn ora an eve pb vagos teur d eek cx Bl ue ap E bv w ax EEC 10 Misc on the HOMELINE system eee eee eau aaa aaa aaa aaa aaa aaa aaa aaa aaa aaa aaa nsn nnns ee enn 11 AA eet ge ce O ECA OE AA 11 LASTS PAA AA 11 Aa ARA AP PA 12 Description of the HOMELINE CBH Advanced system eee eee eee aaa aaa EN NANA 13 Mounting guideline for the CBH sai O AR A A A l AA 13 AIO TENG Mec AE AA 14 Disposal of LINAK s products aaa AA 15 Disposal of Banna ANG a AA AKA AAO 15 Labels ac op AAAA E POOR m 16 AN Ra 18 a APA ER 28 Page 3 of 28 Preface We are delighted that you have chosen a product from LINAK LIN
10. andinavia AB Phone 46 8 732 20 00 Fax 46 8 732 20 50 E mail info linak se www linak se SWITZERLAND LINAK AG Phone 41 43 388 31 88 Fax 41 43 388 31 87 E mail infoGlinak ch www linak ch TAIWAN LINAK A S Taiwan Representative Office Phone 886 2 27290068 Fax 886 2 27290096 Mobile 886 989292100 E mail michael chen linak com tw www linak com tw TURKEY LINAK ith ihr San ve Tic A S Phone 90 312 4726338 Fax 90 312 4726635 E mail info linak com tr www linak com tr UNITED KINGDOM LINAK UK Limited Phone 44 0 121 544 2211 Fax 44 0 121 544 2552 E mail salesQlinak co uk www linak co uk Terms of use The user is responsible for determining the suitability of LINAK products for specific application LINAK takes great care in providing accurate and up to date information on its products However due to continuous development in order to improve its products LINAK products are subject to frequent modifications and changes without prior notice Therefore LINAK cannot guarantee the correct and actual status of said information on its products While LINAK uses its best efforts to fulfil orders LINAK cannot for the same reasons as mentioned above guarantee the availability of any particular product Therefore LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK All sales are subject
11. crap combustion LA27 X X X X CBH1200B X X SMPS001 X X SMPS002 SMPS006 HB20 HC20 X X X Disposal of batteries Details regarding safe disposal of used and leaking batteries Batteries should be disposed in accordance with appropriate federal state and local regulations LINAK recommends that used or leaking batteries are disposed through local recycling system Please do not throw used or leaking batteries in normal household waste or in nature This will cause damage to the enviroment How to deal with leaking batteries Leaking batteries should be disposed as described above If leaking batteries are discovered in the product the batteries must be removed at once to minimise damage to the product If leaking batteries are left in the product it become defective It is recommended to use plastic gloves when handling leaking batteries The contents of a leaking batteries can cause chemical burns and respiratory irritation If exposed to the contents of a leaking battery please wash with soap and water If irritation persists please seek medical attention In case of eye contact please flush eyes thoroughly with water for 15 minutes and seek medical attention Page 15 of 28 Labels Label for CBH Basic KR GROUP 43 HEADQUARTERS WE IMPROVE YOUR LIFE SMEDEVAENGET 8 DESIGNED IN DENMARK DK 6430 NORDBORG Item CBH12XXX Date 2014 09 02 Uln 24V 30V DC lin Max 8A Op INT 10 Max 2min 18min S W
12. ded for use by young children or infirm persons without supervision ZN If there is visible damage on the product it must not be installed Note that during construction of applications in which the actuator is to be fitted there must be no possibility of personal injury for example the squeezing of fingers or arms Only the power supply type SMPS001 SMPS002 or SMPS006 shall be used with the system CBH Advanced System The power supply shall not be covered while operating to allow sufficient cooling of this appliance to be continued Page 6 of 28 2 Furthermore take care about the connecting wires from the power supply to the CBH Advanced System don t damage this by overrun Assure free space for movement of application in both directions to avoid blockade The appliance is only to be used with the power supply unit provided with the appliance Safety issues d The builder of the equipment shall ensure that the use of the component complies with relevant standards like the Machine Directive Care must be taken to avoid squeezing of cables as it can cause movement of the system The SMPS001 002 006 must not be packed in heat insulating material but must be placed so that it can emit waste heat to the surroundings There are no ventilation holes to consider the SMPS emits heat through its surface Only the power supply type SMPS001 SMPS002 or SMPS006 shall be used with the system CBH Advanced System
13. en based on our present technical knowledge We are constantly working on updating the information and we therefore reserve the right to carry out technical modifications LINAK A S Page 4 of 28 Valid for This User Manual is valid for the following products See the first 3 5 characters on the label Actuators LA27 KA20 Control box CBH1220A Power supply SMPS001 SMPSOO2 or SMPS006 Controls HB20 HC20 Accessories BA001 Lightplug001 LED Lightbox001 DC Connector001 USB Connector001 MD1000D2 Page 5 of 28 Important information Important information on LINAK products can be found under the following headings Warning Failure to comply with these instructions may result in accidents involving serious personal injury I Failing to follow these instructions can result in the product being Ws v damaged or being destroyed Safety instruction ZN General Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components It is important for everyone who is to connect install or use the A systems to have the necessary information and access to this User Manual Follow the instructions for mounting risk of injury if these instructions are not followed The appliance is not inten
14. horised LINAK workshops or repairers as special tools must be used and special gaskets must be fitted Lifting units under warranty must also be returned to authorised LINAK workshops Warning If any of the HOMELINE products are opened there will be a risk of subsequent malfunction Warning The HOMELINE systems are not resistant to cutting oil DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY LINAK A S Smedeveenget 8 DK 6430 Nordborg Herewith declares that LINAK HOMELINE products as characterized by the following models and types Control Boxes CB7 CB9H CBH Advanced CBH Basic And Linear Actuators LA27 LA27CS LA28 LA29 LA31 HOMELINE Dual Actuators TD1 TD3 And Controls HB10 HB10RF HB20 HB20RF HB40 HB60 HC10 HC10RF HC20RF And Accessories DC CONNECTOR DJBH LED Lightbox Lightplug001 Massage Motor SMPS001 SMPS002 SMPS006 TR6 USB Connector comply with the following parts of the Machinery Directive 2006 42 EC ANNEX I Essential health and safety requirements relating to the design and construction of machinery 1 5 1 Electricity supply The relevant technical documentation is compiled in accordance with part B of Annex VII and that this documentation or part hereof will be transmitted by post or electronically to a reasoned request by the national authorities This partly completed machinery must not be put into service until the final machinery into which it is to be incorpora
15. linak com br CANADA LINAK Canada Inc Phone 1 502 253 5595 Fax 1 416 255 7720 E mail info linak ca www linak us com CZECH REPUBLIC LINAK C amp S S R O Phone 420581741814 Fax 420581702452 E mail ponizil linak cz www linak cz DISTRIBUTORS ARGENTINA Novotec Argentina SRL Phone 54 11 4303 8900 8989 Fax 54 11 4032 0184 E mail infoQnovotecargentina com www novotecargentina com AUSTRALIA Ballarat Industrial Supplies www ballind com au BL Shipways amp Co www blshipway com au Gas Strut Marine and Industrial www gasstrutmarine com au Prime Motion amp Control www primehyd com au West Vic Industrial Supplies www westvicindustrial com au COLOMBIA MEM Ltda Phone 57 1 334 7666 Fax 57 1 282 1684 E mail servicioalcliente memltda com co www memltda com co INDONESIA Pt Himalaya Everest Jaya Phone 6 221 544 8956 6 221 544 8965 6 221 619 4658 6 221 619 1925 E mail hejplastic div centrin net id www hej co id Fax DENMARK LINAK A S Group Headquarters Guderup Phone 45 73 15 15 15 Fax 45 74 45 80 48 Fax 45 73 15 16 13 Sales E mail infoGlinak com www linak com DENMARK LINAK Danmark A S Phone 45 86 80 36 11 Fax 45 86 82 90 51 E mail linak linak silkeborg dk www linak dk FINLAND LINAK OY Phone 358 10 841 8700 Fax 358 10 841 8729 E mail linak linak fi www linak fi FRANCE LINAK France E U R L Phone 33 0 2 4
16. m drive ru SINGAPORE Servo Dynamics Pte Ltd Phone 65 6844 0288 Fax 65 6844 0070 E mail servodynamics servo com sg WWW Servo com sg SOUTH AFRICA Industrial Specialised Applications CC Phone 27 11312 2292 or 27 11 207 7600 Switch Board Fax 427 11 315 6999 E mail gartht isagroup co za www isaza co za UNITED ARAB EMIRATES Mechatronics Phone 971 4 267 4311 Fax 971 4 267 4312 E mail mechtron emirates net ae www mechatronics ae For contact details on other countries please visit www linak com or contact LINAK INTERNATIONAL Phone 45 73 15 15 15 Fax 45 74 45 90 10 Fax 45 73 15 16 13 Sales E mail infoGlinak com www linak com Page 28 of 28 USA LINAK U S Inc North and South American Headquarters Phone 1 502 253 5595 Fax 1 502 253 5596 E mail info linak us com www linak us com NORWAY LINAK Norge AS Phone 47 32 82 90 90 Fax 47 32 82 90 98 E mail info linak no www linak no POLAND LINAK Polska Phone 48 22 500 28 74 Fax 48 22 500 28 75 E mail dkreh linak dk www linak pl REPUBLIC OF KOREA LINAK Korea Ltd Phone 82 0 2 6231 1515 Fax 82 0 2 6231 1516 E mail scully linak kr www linak kr RUSSIAN FEDERATION 000 LINAK Phone 7 495 280 14 26 Fax 7 495 687 14 26 E mail info linak ru www linak ru SPAIN LINAK Actuadores S L u Phone 34 93 588 27 77 Fax 34 93 588 27 85 E mail esma linak es www linak es SWEDEN LINAK Sc
17. n without much resistance and without using the motor If this is not possible contact your nearest LINAK dealer Usage e Duty cycle 2 18 2 minutes continuous use followed by 18 minutes not in use e Ambient temperature 5 C to 40 C the actuator must also be at this temp ZN Warning e f the actuator does not work as described above the risk of injury due to squeezing can arise The actuator must therefore immediately be sent for service at the nearest authorised LINAK workshop e Do only use the actuator within specified working limits e Do not sideload the actuator Page 13 of 28 Cable relief The CBH features a cable relief option By using these small holes on the CBH you can tie the DC cables from the SMPS unit to the control box by use of standard cable ties It is recommended to use the cable relief especially if the control box is exposed to movement The circles illustrate the small holes on the control box where a standard cable tie can be mounted and the DC cable from the SMPS Handset cable can be fixed The extra cable tie length is just cut off when the cables have been fixed The CBH is a ZEROTM control box A hallmark of the CBH ZERO platform is the very low power consumption in standby mode saving energy and money The low standby consumption is standard A standby power Page 14 of 28 Disposal of LINAK s products As LINAK s customers often ask us how our products can be disposed of or
18. scrapped we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion Guidance We recommend that our products be disassembled as much as possible and divided into different waste groups for recycling or combustion For example waste can be sorted into metals plastics cable scrap combustible material and recoverable resources Some of these main groups can be further divided into subgroups e g metal can be divided into steel aluminium copper and plastic can be divided into ABS PA PE PP As an example the table below breaks down the different components in LINAK products to various recycling groups Product Components Recycling group Column Actuator Spindle and motor Plastic housing Metal scrap Plastic recycling or combustion Cable PC boards Cable Cable scrap or combustion PC boards Electronics scrap Control Box PC boards Electronics scrap Plastic housing Plastic recycling or combustion Cable Cable scrap or combustion Transformer Metal scrap Handset Control Plastic housing Plastic recycling or combustion Cable scrap or combustion Electronics scrap By now almost all our casted plastic parts are supplied with an interior code for plastic types and fibre contents if any Main groups of disposal Product main Metal Cable Electronics Plastic recycling or Comments groups Scrap scrap s
19. ted has been declared in conformity with the provisions of the Machinery Directive 2006 42 EC where appropriate Nordborg 2014 10 09 Dh Ar m LINAK A S John Kling B Sc E E Certification and Regulatory Affairs Authorized to compile the relevant technical documentation Original Declaration Page 10 of Page 10 ol N Misc on the HOMELINE system Warranty There is a 36 months warranty on the HOMELINE products CBH Advanced Systems against manufacturing faults from the production date of the individual products see label LINAK A S warranty is only valid in so far as the equipment has been used and maintained correctly and has not been tampered with Furthermore the system must not be exposed to violent treatment In the event of this the warranty will be ineffective invalid For further details please see LINAK A S ordinary conditions of sale Maintenance Clean dust and dirt on the outside of the system at appropriate intervals and inspect for damage and breaks Inspect the connections cables and plugs and check for correct functioning as well as fixing points o The cleaners and disinfectants must not be highly alkaline or acidic pH value 6 8 Page 11 of 28 ETL marking Due to space limitations the complete ETL marking demands are not represented on the marking plates The full ETL Recognized Component markings are shown here RECOGNIZED COMPONENT TERT Intertek RECOGNIZED COMPONENT TERT
20. tions can always be found here www linak com homeline Page 8 of 28 Only for EU markets This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning use of the appliance In a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Only for Non EU markets Persons who do not have the necessary experience or knowledge of the product products must not use the product products Besides persons with reduced physical sensory or mental abilities must not use the product products unless they are under surveillance or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons Moreover children must be under surveillance to ensure that they do not play with the product Misuse Do not overload the actuators this can cause danger of personal A injury and damage to the system Do not use the actuator system for lifting persons Do not sit or stand on a table while operating risk of personal injury Do not use the system in environments other than the intended indoor use Page 9 of 28 Repairs In order to avoid the risk of malfunction all HOMELINE repairs must only be carried out by aut
21. to the Standard Terms of Sale and Delivery for LINAK For a copy hereof please contact LINAK LINAK WE IMPROVE YOUR LIFE LINAK A S reserve the right to make technical alterations Copyright LINAK 2015 04 MA M9 02 529 A
22. try areas Yet LINAK cannot know all the conditions under which LINAK products will be installed used and operated as each individual application is unique The suitability and functionality of the LINAK product and its performance under varying conditions application vibration load humidity temperature frequency etc can only be verified by testing and shall ultimately be the responsibility of the LINAK customer using any LINAK product LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question Page 26 of 28 Page 27 of 28 FACTORIES CHINA LINAK Shenzhen Actuator Systems Ltd Phone 86 755 8610 6656 Fax 86 55 8610 6990 E mail sales linak cn www linak cn SUBSIDIARIES AUSTRALIA LINAK Australia Pty Ltd Phone 61 3 8796 9777 Fax 61 3 8796 9778 E mail sales linak com au www linak com au AUSTRIA LINAK Reprasentanz Osterreich Wien Phone 43 1 890 7446 Fax 43 1 890 744615 E mail info linak de www linak at BELGIUM amp LUXEMBOURG LINAK Actuator Systems NV SA Phone 32 0 9 230 01 09 Fax 32 0 9 230 88 80 E mail beinfo linak be www linak be BRAZIL LINAK Do Brasil Com rcio De Atuadores Ltda Phone 55 11 2832 7070 Fax 55 11 2832 7060 E mail info linak com br www
Download Pdf Manuals
Related Search