BDA_smartmeter_061008_ENG 1
Contents
1. eene 26 Preparing the smartmeter 80 nnne nnn 26 Executing pdate eee er Ra ER eee ee 27 Editing parameter Sarien e eR Rd Ee red Re Lia 29 SLIDE 32 Trouble shooting 7 reete reete nera 33 DISPOSAl PE DC Dm 34 Technical 35 EID 37 WW ANTONY T 37 Declaration Of 37 4 ENG smartmeter Description Description The smartmeter is a handy digital antenna measuring device for an quick and easy alignment of satellite antennas If a satellite is found the smartmeter shows it on the display and emits a audible signal Signal strength and quality are displayed as numerical values and bar graphs Another measurement value is the forward error correction FEC and the bit error rate BER In addition the picture quality can be revised on the high resoluted 8 9 inch TFT LCD screen Many satellites are pre programmed in order to an quick antenna adjustment The scope of supply contains among the charger a USB cable which allows you to update the smartmeter s software A carrying case serves as protection and for the transport It cares for better readability of the display at sunshine Safety instructions Attention Please re2. 24 04 2008 2339 Anwendung 84 Welw v Figure 2 CD ROM contents gt Switch on the smartmeter Wait until the main menu on the screen smartmeter is indicated Load the transmitting software MeterV1 2 exe Satillite Meter tools _ Help Select COM Port load software i Read parameters Write parameters Edit parameters Figure 3 Sattelitemeterr main menu Select the serial interface on the PC the cable is connected COM1 gt Push the button load software smartmeter ENG 27 Technical specifications r Offnen _ Suchen in 2 Smartmeter_V106 e Name nderungs Typ Gr e Def Dateiname _Standatbin Dateityp Data Files bin Abbrechen Figure 4 Open dialogue c Select the current software file push open transfering data xi transfer progress 14 5 Transfering data After transfering data the smartmeter starts automatically again 2 It can pass to 2 minutes until the smartmeter restarts itself Do not switch off the device until the smartmeter has restarted automatically and indicates the main menu 28 ENG smartmeter Supplier Now the smartmeter is up to date and can be reinstated after a factory reset was made Editing parameters c Select the right serial interface on the PC 1 gt
3. change the parameters of the smartmeter press read parameters to save its current configuration gt Select a file name e g data bin and wait until the process is completed Press edit parameters and choose the file which you have just selected in the example data bin Select COM Pot ead psremeters ole Edt 5 be SIRILIS 5E Indes IMTELSAT zsE ELSAT 3 gt TUEXSAT 42 YE I m acre dnd Apc Figure 5 Edit parameter Now you ve got the option to delete to edit to add as well the transponder as the satellite parameters smartmeter ENG 29 Technical specifications Adding satellites Edit Saillite Please E dit satillite Es rms Hotbird degree 0 360 130 Cancel Figure 6 Adding satellites To add a satellite press Add SAT and give the satellite name and the position After the end of this process press apply Delete satellites Choose the satellite which you would like to remove and press delete SAT After the end of this process press apply Edit satellites Doubleclick on the satellite which you would like to work on Additing transponders To add a transponder select a satellite Press ADD TP An empty transponder is added 30 ENG smartmeter Supplier Now you can
4. 0 SIRIUS 5E 0 EUTELSAT 10E HOTBIRD 13E EUTELSAT 16E ASTRA 19 2E EUTEL 21 5E 5 ASTRA 23 5E BADR2 3 26E 2 ASTRA 28 2E 2 ARABS 30 5E Figure 6 Edit satellites gt Press the 4 gt button to switch between the satellites and transponder list of the chosen satellite 18 ENG smartmeter Supplier gt Press the OK button to display the angle and position of the current satellite gt Press the button to switch to the transponder list c Press the OK button After that you can modify the frequency polarisation and the symbol rate gt To store your changes select save and press the OK button 0002 10 0 EUTELSAT 10E Edit 28 2 0010 30 5 ARABS 30 5E 7 Propertys of the selected satellite smartmeter ENG 19 Technical specifications gt Select the point Dish set up and press the OK button Figure 9 Dish set up gt Press the A V button to move the desired item gt Press the 4 or button to modify the value of the selected item Use the NUMERIC buttons if necessary e Satellite LNB LowL O F e Hight L O F Type 22K e LNB e DiSEqC Level e Switch inuput power e Motor Satellite Satellite selection LNB Type UNIVERSAL 5150 9750 10750 11300 10700 Customised Low L O F Use the NUMERIC keys to input the Low L O F The LNB Type must be set to Customised Hight L O
5. change the frequency symbol rate and polarisation of the transponder while doubleclicking on the respective value After the end of this process press apply As soon as you are ready with the treatment you can write these parametres on the smartmeter Press write parameters After successful transfer the measuring instrument will restart itself independently Attention Never switch off the smartmeter during the update processes Wait until the smartmeter independently restarts This can take up to 2 minutes Alternatively to Sattelite Meter tools you can also use the SetEditsmartmeter that you can find on the added CD ROM or download at http www setedit de SetEditsmartmeter de html smartmeter ENG 31 Technical specifications Danger of electric shock There should be no liquid in the device Never clean it with a wet cloth Pull all plugs before cleaning the device Attention Never use solvet containing agents like benzene or similar Agents like these can damage the surface of the housing gt Pull all plugs from the device USB antenna cable before cleaning c Clean the housing and the display using a soft lint free cloth In case of stronger dirt you can use a mild soap sud gt The keys can be cleaned using compressed air max 2 Bar Do not use any solvents Storing the Product gt Unplug the device from the mains gt Unscrew the LNB cable from the devi
6. etc System Button You can request current information or the software version of your device Note This information is useful to check if there is a newer software available version than the current version on your device smartmeter ENG 25 Technical specifications Needed for operation e smartmeter e PC with System Software Windows and RS 232 Interface e USB cable USB RS 232 e smartmeter Power supply e application software MeterV1 2 exe e Current firmware Download the current software from the smart website www smart electronic de 2 The transmitting software and the original firmware with software version of the delivery status contains the enclosed CD ROM Preparing the smartmeter Attention Secure that during the update the smartmeter is provided with electricity During the update supply the smartmeter with electrical power by power supply unit Its important to make a factory reset after updating the device gt Switch off the smartmeter c the smartmeter by zero modem cable with the interface of the PC Provide the smartmeter with electricity via the power supply unit 26 ENG smartmeter Supplier 2 The connecting cable USB RS 232 is included in the 4 delivery range Executing update ag Bearbeten Ansicht Extras Anderungsdsturn Default Standart iin 02 07 2008 2314 BIN Datei 1473 8 Computer
7. option to search for single channels or using the display for lining a satellite dish up c Press the SYSTEM button to display the System setting menu LNB type Satellite LO LOW identification LO HIGH Frequency Symbolrate nath Polarisation Signal strengt Search in dBuV C N 10dB a BER 2 0 10E 6 RFEC 3 4 STRENGTH 69 QUAY 78 Figure 4 Satellite Finding Finding channels manual Press the FIND button to display the menu satellite finding gt Press the lt or gt button to select a satellite gt Press the button to choose between the following points e Low L O F e LNB type e High L O F e Polarisation e Frequency Symbol rate gt Press the lt or gt button to select a LNB type gt f you would like to enter customised L O F select the point customised and enter the low L O F and high L O F frequency using the NUMERIC buttons Enter the frequency using the NUMERIC buttons Enter the symbol rate using the NUMERIC buttons 33 16 smartmeter Supplier c Press the lt or gt button to select the polarisation c The located channels are attached at the end of the channel list unless they already exist Satellite adjustement gt Press the FIND button to display the menu satellite finding gt Choose a satellite Turn the receiving dish as long as the LOCK LED lights or the joists of the
8. signal level and signal quality are green Once a signal is found the bar graph shows the signal strength and quality In addition C N FEC and a BER after BER are displayed In addition an acoustic signal is represented Notice The satellite call sign see Figure 4 registers which satellite you receive at the moment At some satellites as for example T rksat a wrong satellite call sign is present on single transponders hence the announcement can be falsified Therefore we recommend to leave the setting on the preset first transponder with the search of a satellite Therefore the right satellite call sign is indicated in general always c Setupthe satellite antenna exactly to receive the best signal smartmeter Notice The C N value should amount at least Values of 10dB and more are urgently if you like to have a certain bad weather reserve Or in the case if the signal is distributed via a multiswitch to several receivers The higher the C N value the better The BER value behind 10 is important The higher the better The value should be minimal 10E 4 The optimum is 10E 6 ENG 17 Technical specifications Edit satellites gt Press the MENU button to display the main menu gt Press the or V button to move the cursor gt Select the point satellite setting and press the OK button Figure 5 Satellite setting c Select the point Edit satellites and press the OK button 0001 5
9. F Use the NUMERIC keys to input the High L O F The LNB Type must be set to Customised 22K AUTO ON OFF4 LNB power LNB Tension Off Auto 13V 18V 20 ENG smartmeter Supplier DiSEqC Level DiSEqC 1 0 Switch Input 1 2 3 4 Motor Fixed DiSEqC 1 2 USALS Press the F4 button to save the setting or the EXIT button to store the settings or to leave the menu Follow the instructions on the display smartmeter ENG 21 Technical specifications c Press the SCAN button gt Press the A V button to move the cursor gt Use the lt or gt button to modify the value of the following items e Satellite e Transponder e Motor e Mode Search Satellite Choose the desired satellite Transponder Choose the desired transponders Motor This settings are changed by the Dish set up see page 20 Mode ALL FTA Scrambled Search Satellite transponder gt Having your selection press the OK button to start the search gt After the completion of the search you can leave the menu using the EXIT button Motor Transponder Search mode Search STRENGTH 69 tt ovv 78 oe Figure 10 Automatic search 22 ENG smartmeter Supplier gt Press the ANGLE button to display the calculation menu c Press the lt gt button or use the NUMERIC keys to change the configuration of the selected menu point Hemisphere Azimuth Elevation Pol Figure 11 A
10. Simply television Digital Satellite Meter ENGLISH User manual Version 06 10 2008 Simply television www smart electronic de smart Dear Customer thank you for buying the Smart digital satellite meter Please read this user manual carefully before using this device This operating manual will help you in the appropriate safe and favourable usage of the smartmeter We assume that the user of the smartmeter has overall knowledge regarding the handling of audio and video equipment Each person who connects up operates cleans or disposes of this smartmeter must be familiar with the entire content of this operating manual This device must be familiar with the entire content of this operating manual Always keep this operating manual in the proximity of the devise Please keep this instruction manual for consulting near by the device smart electronic GmbH 2 ENG smartmeter Description e E 2 pride 5 Safety instructions ieroeea tee p 5 Safety of persons eei ei ee detiene eas 5 General informaltlon c ete eerte iet pr 6 Appropriate 7 bruarii e 7 Device overview niin nnnn nian nnnm nnus nnn 8 Start of operat
11. ad the safety instructions carefully before operating the device Please follow all warnings and instructions on the equipment and in the operating manual Safety of persons Ensure that nobody can be hurt by falling tools or parts of the satellite antenna during the adjustment and installation of the antenna For your own security use a rope on sloping roofs smartmeter ENG General information General information Attention The devise should only be operated with the supplied AC adapter at the mains Do not open the meter or the included AC adapter There is danger of life through electric shock Wrong usage of the ports can lead to the destruction of the measuring device Proceed carefully with the measuring device Avoid low temperatures below 0 C or to high humidity e The TFT display can be damaged by mechanical impacts Avoid excessive input voltages Please refer to the technical data starting from page 35 Do not operate with the device eif it has visible damage if there are loose parts in the device e if the device was located outdoors or in damp rooms a extended period of time 6 ENG smartmeter Supplier Appropriate Usage The measuring device smartmeter was developed to measure signals of digital satellite antennas and satellite systems It is exclusively for this purpose and should only be used for this purpose Use the equipment only f
12. be recycled Electronic equipment is not household waste in accordance with directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of 27th January 2003 on used electrical and electronic equipment it must be disposed of properly At the end of its service life take this unit for disposal at a relevant official collection point Help to keep our environment clean wich we are living in 34 ENG smartmeter Supplier Technical specifications LNB Tuner input F type connector Frequency range Input level LNB power supply LNB control signal DiSEqC control Demodulator Front end modul Symbol rate SCPC und MCPC Spectral inversion System resource Processor SDRAM FLASH EEPROM Vide decoder Data rate Resolution Video format Connectors Serial data interface smartmeter IEC 169 24 950 MHz 2150 MHz 65 dBm bis 25 dBm 13 18 V max 400 mA 22 kHz Version 1 0 QPSK 1 5 Mbps bis 45 Mbps Auto conversion 32 bit 16 MByte 2 MByte 8Kbyte up to 15 Mbit s 720 x 576 PAL 720 x 480 NTSC PAL NTSC SECAM USB Type A ENG 35 Technical specifications Power supply Supply voltage Li oN battery Charger Supply voltage charger Dimensions Length x width x height Gewicht Temperature Operating temperature Storage temperature 36 ENG 12 6 V 1950 mA 90 240 V 175 250 V 50 60 Hz 9 5 x 15 5 x 4 5 0 5 Kg 0 C to 40 C 40 C to 65 C smartmeter Suppl
13. ce gt Pull all plugs out of the sockets gt Pack the device and all cables into the original carton gt Store the device and all accessories at a dry and dust free location c Protect the device from frost 32 ENG smartmeter Supplier Fault phenomenon Device does not react Bad picture block defect No or only weak signal No picture no sound Probabable reasons Solutions The battery is empty Charge the battery The antenna is not Adjust the antenna adjusted to the satellite Replace the LNB The LNB is defect Please check all cable connections Adjust the antenna Display Sounds turned off Turn on the display by pushing the F1 button Turn on the sound by pushing the F2 button If you cannot find out what is wrong with your device please contact your local specialized dealer and FAQ being provided in the topical problem solutions smartmeter 2 At www smart electronic de you can find the area Support ENG 33 Technical specifications Attention Never throw the receiver and the batteries in normal household waste They may contain toxic agents that are hazardous to health and environment Therefore dispose of the device and the batteries immediately according to the prevailing statutory regulations Never throw the batteries in normal household waste Figure 13 WEEE Symbol Used devices contain valuable materials that should
14. ete Press respectively the OK button Next to channels you would like to delete should appear an x Press the EXIT button and obey to the instruction on the display smartmeter ENG 13 Technical specifications Factory reset This menu item is described on page 15 Software Version c Press the SYSTEM button At software version you can read the current software state of the smartmeter How to update the software is described on page 26 Note In the support area at http Awww smart electronic de you have got the option to download the topical software for the smartmeter 14 ENG smartmeter Supplier Language select TV Standard Timer Delete channels Figure 3 Factory reset In this menu item you can put your equipment back to the delivery status c Press the SYSTEM button to display the System setting menu c Select the point factory reset Note the instructions on the display and confirm your selection with the OK button or cancel it using the EXIT button Attention All programs and settings configured by you will be reset to delivery status Note After reset to factory default you will have to enter the registration code You can find the appropriate registration code at the back of the measuring device Please contact your dealer in case of a missing registration code smartmeter ENG 15 Technical specifications In this menu you have the
15. ier smart electronic GmbH IndustriestraBe 29 78112 St Georgen Deutschland Service Hotline 00 49 1805 93 52 11 Telefax 00 49 7724 94 78 333 E Mail info smart electronic de Internet www smart electronic de The warranty for the digital satellite receiver Smart smartmeter of the company smart electronic GmbH is in conformity with the prevailing statutory regulations at the time of purchasing the product Declaration of conformit The company smart electronic GmbH IndustriestraBe 29 78112 St Georgen hereby declares conformity with the following guidelines and standards for this product e Guideline for low voltage 2006 95 EG EN 60 335 1 EN 60 335 2 15 Guideline for electromagnetic compatibility 2004 108 EG e EN 55 013 2001 e EN 55 020 EN 61 000 3 2 2000 EN 61 000 3 3 1995 1 2001 e 61 938 Equipment type model Digital smartmeter smart electronic GmbH smartmeter ENG 37 Simply i television www smart electronic de smert
16. ion n niei aie caste eek 10 Battery eene tees enmt ets 10 Switch on the Device 0 2 244 11 enne entere 10 Lithium ions battery 11 Charging the 11 Storing of the 11 System settings aeree e cn cie E 12 hel able ta Dats De bec 12 13 Delete Channels 13 iE 14 Software 14 gencre 15 Satellite finding iini eterno ee 16 Finding channels Manual sese 16 Satellite 0 41 1 0 nennen nnne nnne 17 smartmeter ENG 3 Satellite iecit ide 18 eesti terete reentrant eth el ence otek teeta 20 Automatic Scal oiii edere risit 22 Angle calculation 23 Update changing parameters
17. ngle Calculation gt Press the or V button to select the following points e Satellite Longitude Location e Latitude e Hemisphere Angle calculation Satellite Select the desired satellite Longtitude Input your local longtitude Location Input the direction Latitude Input your local latitude Hemisphere Input your local hemisphere smartmeter ENG 23 Technical specifications c After the completion of all values select Angle Calculation and press the OK button Azimut shows the azimuth of the chosen satellite Elevation shows the angle of elevation of the chosen satellite Polarity shows the polarity angle of the chosen satellite Channel selection c Press the OK button and choose the desired program using the A or V button Press the OK button again Satelite ASTRA 19 2E Type Free Frequency 11836 H 27500 Figure 12 Menu configuration If you know the channel number you can enter it in tv mode with the NUMERIC buttons and wait 2 seconds until the channel is changed 24 ENG smartmeter Supplier Channel information gt Press the button in the TV mode to get additional information about the current channel SEBASTIAN K RBER zu Gast bei Stefan Raab 2 TV ASTRA 19 2E 12 22 01 Jan 2009 0007 ProSieben TP 12544 H 22000 Figure 13 Additional Information gt Use this menu to check the satellite name channel name the transponder parameter or the signal strength
18. on the Device gt Press atleast 2 seconds the red power button on the smartmeter Enter the registration code using the numeric keys You have to enter the registration code before the first operation You can find the appropriate registration code at the back of 2 the measuring device Please contact your dealer in case of a missing registration code 10 ENG smartmeter Supplier Explosion danger Never conntect the two poles and with each other Attention Do not store or operate the accumulator above 40 C Do not burn or damage accumulator Avoid contact with water Charging the battery 2 2 The maximum battery charging time is approximately 12 hours A charging circuit in the measuring device provides an optimal charge of the battery The device is charged if it is switched off Turn the device off if it is not already off Connect the Euro main cable with the external AC adapter Connect the external AC adapter to the power grid Connect the AC adapter to the low voltage port at the bottom The battery is charged as soon as you connect the AC adapter to the smartmeter viv The Power LED shows the battery status e green the battery is charged e red the battery is completely loaded Storing of the batteries Store the batteries between 0 Celsius and 40 Celsius Load the accumulator at a longer storage every two weeks to avoid a depth discharge sma
19. or the purpose which is described in this manual Follow all information in this manual particularly the safety instructions on page 5 Any other usage is rated as not properly and can result in damage or even injury There will be no liability for damages caused by a non intended use Delivery range Please check if the delivery is complete Included in delivery e device smartmeter e acarrying bag with sunshade e aPC connection cable with RS 232 and USB plug Type e acar adapter cable 12 V e an extern charger e Euro mains cable e anuser manual a CD ROM including the Software for the smartmeter If the delivery should be incomplete contact your specialist dealer or smart electronic GmbH IndustriestraBe 29 78112 St Georgen GERMANY Service Hotline 0049 1805 93 52 11 Telefax 00 49 7724 94 78 333 E Mail info smart electronic de N smartmeter ENG Technical specifications Device overview 2 smartmeter 4 3 5 a 57 Om Ow Ow ok 6 _ Ht 2 5 C 9 D 2 10006 J 9 1 Front of the smartmeter 8 ENG smartmeter Supplier 1 LNB IN Digital satellite signal input 2 LC Dispay Display of the TV picture the menu and the measured values 3 POWER Display of the energy state LED Operation red the measuring device i
20. rtmeter ENG 11 Technical specifications gt Press the MENU button Select the point system setting Confirm your selection using the OK button Language select TV Standard Timer Delete channels Factory reset SW Ver Figure 2 System setting Menu language setting Press the SYSTEM button to change the menu language gt Select the point Language select gt Choose your desired language using the lt or gt button gt After your selection press the EXIT button and follow the instructions on TV standard In this menu you can select the TV output standard c Press the SYSTEM button gt Select the point TV standard gt Choose your TV standard using the 4 or button 12 ENG smartmeter Supplier You can choose between the following TV standards PAL SECAM NTSC e Auto gt After completion of your selection press the EXIT button and follow the instructions on the display Timer Through this setting you can select the satellitemeter s LCD shut off time c Press the SYSTEM button gt Press the lt or gt button to set the timer gt At least press the EXIT button and follow the instructions on the display Delete channels You can delete single channels from your channel list in this menu c Press the SYSTEM button to retriever the menu system settings Select the menu item delete channels gt Select the channels you would like to del
21. s switched on Off the measuring device is switched off In charge Green The battery is charged Red The battery is fully charged 4 LOCK LED LED lights when a signal is received 5 FUNCTION F1 toggle the Display keys F2 Mute F3 Additional information about the current program F4 switch between radio TV mode 22K 13V 18V Lights if 22K 13V 18V signals are received LEDs 6 Navigation Navigation through menus cross switching programs A V volume control 4 gt 6 1 OK button OK button confirmation of a selection 7 Numeric Direct enter of numbers keys 8 FIND button FIND menu for a quick and easy alignment of a satellite antenna 9 Menu button Display the main menu 10 EXIT button Leave the current menu cancel operation 11 ANGLE Display the calculation menu button 12 SYSTEM Configuration of all system parameter button Display current software version 13 POWER Switch device on off button 14 SCAN button Display the auto scan menu 15 AC adapter Low volt port for power supply connection port 16 USB Port USB port for PC connection smartmeter ENG 9 Technical specifications Start of operation Battery Before the first operation with the measuring device charge the battery completely see also chapter Lithium lon battery on page 11 Load the accumulator during the first loading procedure at least 5 hours 2 The maximum battery charging time is approximately 12 hours Switch
Download Pdf Manuals
Related Search