Home

Instructions.

1. PERPE A un 6X G 10 X 1 PAN SCREWS
2. INSTALLATION MANUAL YM11515 4 HIGH LATTICE X PRIVACY PANEL LILITYT TOY ITTIIII LE Yardistry Ltd Mount Forest ON Canada NOG 2L1 Toll Free Customer Support 1 888 509 4382 info yardistrystructures com www yardistrystructures com Revised 04 13 2011 1 IMPORTANT SAFETY NOTICE Yardistry components are intended for privacy decorative and ornamental use only Product is NOT INTENDED for the following A safety barrier to prevent unsupervised access to pools hot tubs spas or ponds Safety railings for elevated platforms or decks As load bearing support for a building structure heavy objects or swings Used in structures that trap wind rain or snow that would create extra load on the product Permanent structures may require a building permit As the purchaser and or installer of this product you are advised to consult local planning zoning and building inspection departments for guidance on applicable building codes and or zoning requirements Wood is NOT flame retardant and will burn Grills fire pits and chimneys are a fire hazard if placed too close to a Yardistry structure Consult user s manual of the grill fire pit or chimney for safe distances from combustible materials During installation follow all
3. panel assemblies are created pr the fight PFEF Fig 1B Filler Strips on Bottom of Panel 4X pa ONE HIGH X TOPPER 4x G 8 2 1 4 WOOD SCREWS 4X F5 THREE HIGH LATTICE PANEL STEP 2 ASSEMBLE WALL Q Fig 1 1 Assemble panels together in configuration shown Fig 1 Insert male connector into female Slide down until flush with adjacent panel as shown Fig 1A 2 Secure Panels with S4 2 1 4 screws provided in pre drilled holes as indicated by arrows in the direction of the arrow Fig 1 Fig 2 3 Secure R Top and Bottom Rails to Panel Assembly with S4 2 1 4 Wood Screws locations indicated by arrows in the direction of the arrow Fig 2 R Top and Bottom Rails will overhang 1 4 on either side of panel R Top and Bottom Rails may need to be cut to 6 6 1 2 2m It is recommended to use a Mitre Box or Mitre Saw 4 4 4 4 4 4 4 4 2x TOP amp BOTTOM RAIL 24x GO 8 2 1 4 WOOD SCREWS STEP 3 INSTALLING PANEL CLIPS Qu Au 1 Postition Panel Clips in locations indicated in Figures 1 and 1A Ensure Panel Clips are oriented in the same direction facing outside the Pergola 2 Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3 8 or 3 5cm away from the side of the post as shown in Fig 2 3 With Panel Cli
4. fastening screw injury or damage to the L 6 or lag to prevent assembly make sure to get help splitting of wood Tighten Measure Check that assembly is square Pace istance a Se This indicates time to tighten bolts but U jing tava not too tight Do not crush the wood Sed Mod ape TO assure This may create splinters and cause proper location structural damage MATERIAL LIST R 2 Top and Bottom Rail 4 One High X Topper 4 Three High Lattice Panel 8 x 2 1 4 Wood Screw aww 10 x 1 Pan Head Screw Da 8 x 1 1 2 Wood Screw 6 Panel Clips STEP 1 ASSEMBLE PANELS 1 Remove the upper metal connectors on both sides of PL3 Three High Lattice Panel Reattach the metal connectors to PL3 by securing the bottom two holes of the metal connectors to the top two holes on PL3 so that the metal connectors stick out from the top Slide PX1 One High X Topper between the two protruding metal connectors on the top of PL3 Attach the metal connectors to PX1 Fig 1A Ensure Panels are oriented correctly Fig 1B 2 Secure panels with a S4 2 1 4 Wood Screw the location indicated by the large arrow in the direction of the arrow 3 Repeat until four
5. ps in place mark screw holes with a pencil and pre drill holes with a 1 8 drill bit Not provided 4 Secure Panel Clips in locations indicated in figure 1 and 1A with S7 8 x 1 1 2 wood screws Fig 1A dp Inside Outside ergola ergola paes l W 3 5cm Pre drill holes and secure with S7 8 x 1 1 2 Wood Screws 75 190 5cm 40 101 6cm p q 10 25 3cm j 3 EN 6X PANEL CLIPS 12x 48 X 1 1 2 WOOD SCREW STEP 4 INSTALLING WALL INTO PERGOLA DA Pr 1 With the help of an adult place the Wall on Panel Clips as shown Fig 1 allowing a 4 gap between the bottom of the post and the bottom edge of ll the bottom rail on the panel assembly 2 With a 1 8 drill bit predrill holes as shown in figure 2 3 Fasten the Wall to the post and Panel Clips with a S5 1 Pan Head Screw provided in location of arrows Fig 1 N gt Fig 2 Predrill Holes and Fasten with S5 1 Pan Head Screw HEHHE E ILETITIIT HEHEHHE HEHEHEHH ALO zd LLLILIIIIT HUI LLIILIIIH HG LLLIILIIIIT HUI LIIIIITITIN
6. safety warnings provided with your tools and use OHSA approved safety glasses Some structures may require two or more people to install safely Check for underground utilities before digging or driving stakes into the ground General Information Wood components are manufactured with Cedar C Lanceolata which is protected with factory applied water based stain Knots small checks cracks and weathering are naturally occurring and do not affect the strength of the product Annual application of a water based water repellent sealant or stain will help reduce weathering and checks Warranty Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original retail purchase for manufacturing defects and if installed as per manufacturer s installation instructions Patents Pending Tools Required Tape Measure 2 Phillips or Robertson Safety Glasses Carpenters Level Bits or Screwdriver Adult Helpers Carpenters Square 1 8 Drill Bit Standard or Cordless Pencil Drill 8 Step Ladder Keys To Assemble Success This identifies information that requires special Check that set or assembly is properly level Use attention Improper assembly could lead to an before proceeding Level unsafe or dangerous condition E tt Where this is shown 2 or 3 Pre drill 1 8 amp 3 16 Bit I f c p ep people are required to safely Pre drill a pilot hole complete the step To avoid ko P before

Instructions.

Contents

Download Pdf Manuals

Related Search

Related Contents