Manual - Faderfox
Contents
1. Start Encoder 5 Nudge function allows a finer synchronization of the intern clock engine Each encoder step shifts the clock only one tick 96 forward clockwise or backward counter clockwise Push the encoder to start the sequencer Start function isn t available when the device is synchronized externally Red LED is lit when sequencer runs Sync Stop Encoder 6 Int intern clock is used USb extern clock synchronization Midiclock via USB port nni d extern clock synchronization Midiclock via Midi in port Push the encoder to stop the sequencer Red LED is lit when the sequencer is stopped Push encoder when LED is lit to reset the pattern counter LED will be off Swing Remote Encoder 7 no no swing active 8 1 each 2nd 8 note will be shifted about one tick 96 8 2 each 2nd 8 note will be shifted about two ticks 2 x 96 16 1 each 2nd 16 note will be shifted about one tick 96 16 2 each 2nd 16 note will be shifted about two ticks 2 x 96 82 each 2nd 32 note will be shifted about one tick 96 8272 each 2nd 32 note will be shifted about two ticks 2 x 96 Push encoder to switch on off the remote function Red LED shows the state By activated remote function you can control the transposition separate activation of all 8 pattern pattern length pattern direction scales and clock reset To control these by incoming note commands over 4 octaves you need a connected midi keyboard P2. see below Setup 28 is recommended to control parameters of selected track tracks below track 16 are available too GrP1 GrP4 For free use trAC group 5 controls various parameters of the selected track encoder 1 track send 1 A push button 1 track view encoder 2 track send 2 B push button 2 clip view encoder 3 track send 3 C push button 3 stop clip red led shows stopped clip encoder 4 scene select push button 4 launch clip red led shows available clip encoder 5 track select push button 5 track arm red led shows arm state encoder 6 crossfader assign push button 6 track monitor red led shows state encoder 7 track pan push button 7 track solo red led shows solo state encoder 8 track volume push button 8 track active red led shows active state Vol group 6 Volume and track active of track 1 to 8 RAC group 7 Rack control of macros 1 to 8 and some rack functions encoder 1 macro 1 push button 1 track view encoder 2 macro 2 push button 2 rack on off encoder 3 macro 3 push button 3 previous rack encoder 4 macro 4 push button 4 next rack encoder 5 macro 5 push button 5 show rack encoder 6 macro 6 push button 6 lock rack encoder 7 macro 7 push button 7 previous track encoder 8 macro 8 push button 8 next track GLob group 8 Global controls encoder 1 tempo coarse push button 1 nudge down encoder 2 tempo fine push button 2 nudge up encoder 3 q
3. USB cable iPad with 1055 or higher connection by apples camera connection kit MIDI device with standard midi in port Spin DIN socket connection by enclosed adapter cable USB power adapter 5V min 200mA if you want to control only midi gear Controller mode Controller mode is the basic mode of the SC4 Here the encoders are used to control any parameters in your soft or and hardware by standard midi commands like CC and notes First choose the group by the green buttons The display shows the group name Gr P1 Gr P8 Turning and pushing of the encoders can send different commands which you can program in edit mode LED crowns and red LED s in the center of the crowns show the current value and states of the corresponding encoders After turning or pushing any encoder you can see the numerical value in the display too A programmed acceleration gives a better feeling for the encoders so you can go from min to max value easily Hold any shift key while you turn the encoders to have a precise control without acceleration To get the encoder value shown on the display without changing hold any shift key and press the encoder The right point in lower right corner of the display shows incoming midi data It flashes bright when the device receives controller data Low flashing indicates midi clock or other midi data Ableton Live mode The setups 28 to 30 are preconfigured for using with Live 8 9 The display shows special group names
4. pitchbend and control change in relative and absolute mode with different acceleration amounts are possible All these properties are fully programmable on the devices very fast and easy for each control separately A small display informs about programmings and control values The encoders can work as high resolution 14bit controllers too control change or pitchbend which makes them suitable for sensitive parameters like resonating filter cutoffs or similar things Use the internal 30 setups to save your individual settings Backup and restore of all settings by sysex dumps is possible too The factory settings are perfect to control music and video software products out of the box if they are freely assignable So any additional device programming isn t necessary for many applications The little box is also a great extension for your Ableton Live setup There you can control all the continues parameters like track volumes rack macros send amounts track pannings etc A special control surface script for Ableton Live 8 9 with all necessary mappings is enclosed in the package With that script you can also use two SC4 devices to control up to 16 tracks simultaneously The integrated monophonic sequencer with 8 tracks and 8 patterns is another highlight of the SC4 The sequence unit is a bit similar to the M185 seuencer from RYK with a lot of extensions First you can switch each of the 8 controller groups to any of 7 different track types like
5. receive mode Factory settings Commands for setups 1 to 16 17 to 30 Encoder 1 8 absolute 7 bit channel number setup number acceleration mode 3 group 1 CC 000 007 000 007 track Push button 1 8 toggle mode channel number setup number 16 for setup 17 30 group 1 cc 064 071 note 064 071 track 2 3 4 5 6 008 015 016 023 024 031 032 039 040 047 008 015 016 023 024 031 032 039 040 047 2 3 4 5 6 072 079 080 087 088 095 096 103 104 111 072 079 080 087 088 095 096 103 104 111 Setups 17 to 27 are preconfigured to use the sequencer on groups to 7 Special different preferences for Ableton live setup group channel encoder CC push button note 28 28 5 6 14 13 056 063 040 047 120 127 104 111 General setting effected only by factory reset all Setup Routing mode Tempo Gate time Pattern length Transpose Sync Swing Direction Scale Remote channel Remote note 01 6 midi to midi midi to usb 120 0 bpm 100 ms 32 off 0 intern no forward chromatic 01 0 C 1 7 048 055 048 055 7 112 119 112 119 28 30 7 13 048 055 112 119 8 056 063 056 063 8 120 127 120 127 28 30 8 13 056 063 120 127 User manual SC4 version 1 Mathias Fuchfi Software Entwicklung Op n Idenkamp 13a 22397 Hamburg Germany info faderfox de www faderfox de
6. reset Push the encoder to activate one of the following note scales red LED is off no scale chromatic red LED is lit C major scale red LED blinks C minor scale Only related notes of a activated scale are available in the note track All other notes will be corrected temporarily Random function follows selected scale Edit mode The edit mode allows the programming of the controls encoders and push buttons and the handling of setups and routings Start and leave edit mode by pressing both shift keys at the same time The activated mode is indicated by display Ed t and or blinking group LEDs To edit any control choose the group by the green buttons select the control by encoder 4 and then set preferences for type channel command number and mode by encoders 5 to 8 To check the programming immediately while staying in edit mode you can send commands by holding down any shift button and turn or push the encoders You can swap the group mode separetely for each group between controller mode and sequencer mode by pressing the green group track button while holding any shift key The display shows Gr P1 Gr P 8 for controller mode or any track type see below for sequencer mode In sequencer mode you can choose track type channel and command number by encoders 5 to 7 Setup Encoder 1 SE01 5E30 select setup 1 to 30 Modified setup data are indicated by blinking red LED 1 To store setup data hold down encoder
7. track types available All types except the CC type can be work only once in the same setup Track types notE Oct AcLn LEn CC Note track contains the notes for each stage encoders notes F3 to H4 two leds lit for black key notes push buttons note on off To send other note below or above use octave track Stage will be paused mute if stage is switched off The associated channel is selected in edit mode Octave track contains the octave values for the note track encoders octave 1 to 7 4 as standard push buttons octave on off Accent track contains the accent velocity values for the note track Further you can switch on off links between the stages by the push buttons encoders accent 0 to 127 push buttons link on off Link function is useful for portamento effects in legato playmode Length track contains the duration values for each stage Further you can switch on off a skip for each stage by the push buttons encoders length 1 to 8 clocks push buttons skip on off Each clock has duration of 32 note so you get a max stage length of 4 The stage will be not played also without pause if skip is activated Repeat track contains the repeat values for the note track encoders repeat 1 to 8 clocks push buttons repeat on off Each step has a duration of 32 l triggers each 32 note 2 triggers each 2nd 32 note 3 triggers each 3rd 32 note 4 triggers each 4th 32 note 5 tri
8. value 0 release toGL send toggle command with LED control value 127 on value 0 off LED s will be always controlled by feedback data same commands as corresponding push buttons Set modes of all encoders or push buttons in the same group at once by holding down encoder 8 push button while running bar lines shown Factory reset MESE Reset selected setup by holding down both encoders 1 2 while running bar lines shown rESA Reset all setups by holding down both encoders 3 amp 4 while running bar lines shown Send Receive setup data Sndc Send selected setup by holding down both encoders 5 amp 6 while running bar lines shown SndA Send all setups by holding down both encoders 7 amp 8 while running bar lines shown Sn00 5n99 shows the send progress in percent 0 to 99 Abort is possible by pressing any shift key Data will be send as sysex dump to both USB and Midi ports Activating receive mode by holding down both encoders 6 amp 7 while running bar lines shown Then send setup data from any sysex dumper software to the device It s strictly recommend to avoid sending sysex data to USB and Midi in ports simultaneously The right point in lower right corner of the display shows incoming midi data rc00 rc99 shows the receive progress Abort is possible by pressing any shift key Edit shows the successfully receiving and storing of the setup data Err shows a receive error Try again by pressing shift and activating
9. ay attention that you can activate more than one pattern if you press the associated keys at the same time Press only one pattern key to have only one pattern activated at the same time All pattern and direction changes effect on next pattern begin Transposition remote works immediately The remote commands are listed below C pattern 1 base note C pattern direction forward D pattern 2 D pattern direction pendulum E pattern 3 F pattern 4 F pattern direction backward G _ pattern 5 G pattern direction random A pattern 6 A clock reset pattern restart H pattern 7 C1 pattern 8 Cl pattern length 1 clock D1 pattern length 2 clocks D1 pattern reset off El pattern length 4 clocks F1 pattern length 8 clocks Fl no scale G1 pattern length 16 clocks Gl C major scale Al pattern length 32 clocks Al C minor scale H1 pattern length 64 clocks C2 transpose 12 semitones i C3 no transpose C4 transpose 12 semitones To assign the base lowest note and channel for this function please hold down the encoder until the red LED blinks and play any C note on your keyboard Red LED will be off after receiving a valid note command Direction Scales Encoder 8 FOr pattern runs forwards PEnd pattern runs back and forth pendulum DAC pattern runs backwards rAnd pattern stages will be triggered randomized Changed direction effects on next pattern begin or pattern
10. ed with the controller no manual mapping necessary USB interface with bus powering class compliant no driver necessary consumption lt 500mW MIDI in and out ports with routing and merge functionality 8 push encoders with detents resolution about 30 pulses 8 LED crowns to show current values of all encoders and push buttons 4 digit display to show control values and programming data 14 bit high resolution encoder mode for sensitive parameters Data feedback for encoders avoid value jumps All controls incl push buttons fully programmable in the device by channel type number and mode Different command types like control change CC pitch bend program change and notes Advanced programming functions like copy paste and channel set 8 groups for all controls About 128 commands per setup 16 controls x 8 groups Integrated sequencer with 8 configurable tracks 7 different track types like note repeat CC length skip accent link etc 8 sequencer patterns with each 8 stages are linkable to max 64 stages Remote function by a connected midi keyboard transpose direction pattern select 30 setups with backup restore function contain controller and sequencer settings for groups and patterns Very compact design in a black casing with metal faceplate laser engraving 180x105x70 mm 350 g System requirements PC or Mac with a free USB port 1 0 or higher or any USB hub connection by inclosed
11. elect push button 5 start encoder 6 cue volume push button 6 stop encoder 7 master pan push button 7 record encoder 8 master volume push button 8 view arrangement session Sequence mode In sequence mode the encoders are used to control different stage parameters depending of the track type First choose the track by the green buttons The display shows the track name type see below Turning and pushing the encoders changes track parameter in the 8 stages of a pattern LED crowns and red LEDs in the center of the crowns show the current value and stages states After turning or pushing any encoder you can see the numerical value in the display too Hold left shift key while you turn the encoders to change all 8 stages at once If you hold right shift key and press any push encoder all 8 stages will change to same states To get the encoder value shown on the display without changing hold left shift key and press the encoder Blinking crowns show played stages The right dot in lower right corner of the display shows incoming midi data It flashs bright when the device receives controller data Low flashing indicates midi clock or other midi data Random function A very special feature is the random function which works on all encoder values of a track by pressing left shift key the green track group key To get randomized states hold right shift key and press a green track group key Track description There are 7 different
12. ggers each 5th 32 note 6 triggers each 6th 32 note 7 triggers each 7th 32 note Probability track contains the probability values for each stage encoders probability 0 to 7 push buttons probability on off 0 stage will be not triggered l stage will be triggered very rarely 7 stage will be triggered mostly CC track contains the controller values for each stage encoders control change value 0 to 127 push buttons CC on off The associated CC number and channel are selected in edit mode Pattern control In pattern control mode the encoders are used to control the 8 available patterns of the selected setup Start pattern control by pressing the green buttons 6 and 7 shortly Both LEDs 6 and 7 are lit and the display shows PAt 1 PAt 8 You can also hold both buttons longer than 1 second while you make any modifications In this case the unit switches back to the last active group after releasing the buttons You activate or deactivate the patterns by pushing the associated encoder The red LEDs show the state of every pattern The patterns will run sequentially in a loop To select a pattern for editing you simply turn the encoders The display shows the current selected pattern onai Blinking crowns show running patterns A crown is lit if the pattern is stopped All crowns are off when the sequencer is reseted A blinking red LED indicates a modified pattern Push encoder while you hold left shift key t
13. ion tempo is more precise with every additional tap After a pause of about 2 seconds without taps the calculation will be reseted Gate Reset clock Encoder 2 0010 3000 gatetime for each trigger in milliseconds 10ms to 3 sec Red LED shows the trigger length Note that a greater value as stage length will result in possible trigger suppression on you instrument Hold any shift key while turning the encoder to have a finer adjustment Press the encoder to reset the internal clock so the pattern starts again immediately This function allows a manual synchronization More precise synchronization is possible by the nudge function below Length Encoder 3 001 064 1 to 64 clocks until pattern reset To get a stable groove especially after stage length modification on the fly it s good to know about this reset function Hold any shift key while turn the encoder to have a finer adjustment You can switch the function on off by pushing the encoder Red LED shows the state Transpose Set notes Encoder 4 12 00 12 transpose about 12 to 12 semitones The function allows to change the key off all patterns on the fly A changed transposition effects on next pattern begin Hold down encoder push button while running bar lines shown to modify the notes in the current selected pattern This follows the current transposition and activated scale see below After that the transposition and scale will be switched off Nudge
14. itions must be met in order to claim the warranty services Instrument is either in its original packaging or similar packaging Copy of the invoice with the serial number clearly visible Meaningful error report or description of the error is attached The buyer assumes all costs and dangers of return shipments to the manufacturer Since the user s manual which is included with each instrument also affects the warranty conditions especially regarding safety issues 1t is absolutely essential that you read through and follow all instructions Safety precautions and servicing Instrument s intended use is based on the functions and procedures contained in this manual Read all instructions for use as well as all enclosed literature before using the instrument Use only in closed rooms not for outdoor use Never use in a moist or humid environment laundry rooms swimming pools etc Not for use in the vicinity of heat sources radiators ovens etc Operational temperature is in the range of 0 40 C Not for use in the vicinity of flammable material The instrument should not be in direct or prolonged contact with sunlight Dusty environmental conditions should be avoided Connect only to USB ports of computers or hubs No foreign objects are permitted inside the instrument casing No liquids should get inside the instrument casing Never let the instrument fall to the ground casing and or c
15. micromodul SC4 Midi in Midi out Pattern reload ABBA HH Pattern write Edit Random Edit Random all Encoders all Keys Eo us at A a ee lt 5 5 SOS COS QA Wy ca o A 1 QA Wy 209 O O8 lOs O SOs Qe O Os 206 O Os GON ION ION JON o on 120 on 20 OOs 95 OOs Setup Routing pyi Paste Tempo fine Quantization O Gate Transpose Reset clock Set notes Tempo coarse Direction Scales Pattem Sequence 6 control 7 control 8 O8 o faderfox User manual Provision of guarantee and product liability The seller warrants for faultless material and proper manufacture for a period of 24 months from the date of sale to the end user Excluded from the stated guarantee are defects on parts as the result of normal wear and tear These parts are mostly faders sliding guides potentiometers encoders buttons switches and touchpads Also excluded from the guarantee are damages that are the result of incorrect or inappropriate handling excessive force mechanical or chemical influences incorrectly comnecting the instrument with other instruments incorrect or inappropriate use The warranty is void if the instrument is opened or changed In addition there is no warranty for individual parts and components in particular semiconductors and disposables consumables The seller is not liable for consequential damages which are not the result of criminal intent or negligence on his part The following cond
16. note octave repeat CC accent link length skip and probability Each of the 8 available sequencer stages of a pattern can have its own length about 1 to 8 clocks which was also one of the unique features of the M185 sequencer Two special groups controls various pattern and sequencer functions 8 patterns with 8 stages are linkable to a maximum amount of 64 stages You can write reload and copy patterns on the fly Because of many different sequencer functions like tempo gate length transpose swing scale and direction the SC4 becomes very flexible Of course there are also midi clock sync tempo tap clock reset reset counter and a nudge functions to get the perfect sync with your other gear Remote the sequencer transpose direction clock reset and pattern select by a connected midi keyboard to have a much greater performance Special random and probability functions give your tracks more variations and liveness Combinations of controller and sequencer groups are possible as well and all of these you can program independently for each of the 30 setups Simultaneous control of external gear and software instruments is no problem for the SC4 due to the available USB and MIDI ports Check out this amazing power box and you will get a reliable mate Features Universal controller and sequencer for all kinds of midi controllable hard and software Pad compatible with camera connection kit Control surface script for Live 8 9 is shipp
17. o reload the pattern but pay attention that all track modifications will be lost Hold right shift key and push encoder to write the pattern to memory which must be done for each pattern separately Note that each setup has its own pattern track data but these will not be saved in edit mode To copy the current selected pattern just simply turn the encoder of the destination pattern while holding any shift key Each pattern holds 8 stage data sets of all available tracks Sequence control Start sequence control by pressing the green buttons 7 and 8 shortly Both LEDs 7 and 8 are lit and the display shows SEQU You can also hold both buttons longer than 1 second while you make any modifications In this case the unit switches back to the last active group after releasing the buttons Now you have access to various sequencer main parameters described below You can save the sequence control parameters except nudge separately as defaults by holding right shift key and press the associated encoder These parameters will be reloaded by each setup change Tempo Tap Encoder 1 0200 2500 bpm from 20 0 to 250 0 Blinking red LED 1 shows the tempo Hold any shift key while turn the encoder to have a finer adjustment The tempo adjustment isn t relevant while the device is extern synced see sync below Tap the tempo by pushing the encoder to snchronize the device manually While you tap an average is calculated so your destinat
18. ontrol elements may be damaged If the instrument must be opened for example to remove foreign objects from the casing or for other repairs this may only be done by qualified personnel The USB cable must be disconnected before opening the instrument Guarantee is void for defects that occur if the instrument was opened by an unauthorised or unqualified person Use a soft towel or brush to clean the instrument Please do not use any cleaning liquids or water so you avoid any damages to the instrument Package contents Device USB cable with angle plug Midi adapter cable with angled 3 5mm jack plug Manual Quick start guide CD with settings and manuals Introduction Thank you for choosing a Faderfox controller These probably world s smallest controllers are designed for live use on stage All Faderfox controllers are professionally hand crafted in Germany ensuring high quality The 4th generation brings a lot of new features like additional MIDI connections black faceplates with laser engraving and updatable firmware First part of the SC4 is a universal controller for all kinds of midi controllable hard and software The all rounder has 8 push encoders with detents all switchable to 8 controller groups that allow to control a total amount of 128 control parameters Amazing LED crowns show the current values of all encoders and push buttons in a very ergonomic way Various kinds of midi commands like program change
19. push button while running bar lines shown Attention All edited setup data is lost if you change setup number without storing before Routing Encoder 2 Rou0 no Midi routing Roul USB in to Midi out Rou2 Midi in to Midi out Rou4 Midi in to USB out Rou5 Midi in to USB out USB in to Midi out Rou6 Midi in to Midi out Midi in to USB out Routing will be stored automatically by leaving edit mode Copy Paste Encoder 3 CPYS copy current setup completely CPYG copy current group completely Poste paste to current setup PStG paste to current group To copy or paste hold down encoder 3 push button while running bar lines shown The last copy will be available in the copy memory permanently Control Encoder 4 Enc1 Enc8 select encoder 1 to 8 for editing btn1 btn8 select encoder push button 1 to 8 for editing Selection of any encoder or push button is possible too by holding down shift and turn or press encoder Type Encoder 5 Encoder types CCr1 control change command in relative mode 1 values 1 127 CCr2 control change command in relative mode 2 values 63 65 CCAb control change command in absolute mode values 0 to 127 standard mode mostly used Pr GC program change command values 0 to 127 CCAh two control change commands MSB LSB in high resolution mode values O to 16383 Pbnd pitch bend command values 0 to 16383 Push button types note note command note values 0 to 127 velocity 127 press on veloci
20. ty 0 release off CC control change command value 127 press on value 0 release off Set types of all encoders or push buttons in the same group at once by holding down encoder 5 push button while running bar lines shown Sequencer track types not E notes stage on off Oct octave octave on off AcLn accent stage link LEn length stage skip rEP repeat repeat on off Prb probability probability on off GE controller CC controller on off Channel Encoder 6 Ch01 Ch16 choose midi channel 1 to 16 also used for CC and note sequencer tracks Set channels of all encoders or push buttons in the same group at once by holding down encoder 6 push button while running bar lines shown Number Encoder 7 n000 n127 choose controller or note number 0 to 127 also used for CC sequencer tracks To assign number channel and type by incoming midi commands learn mode please hold down the encoder until the red LED blinks and then send any valid command control change program change pitch bend or note Red LED will be off after receiving a valid command Mode Encoder 8 Encoder modes Acc0 no acceleration by faster turning Acc1 low acceleration by faster turning Acc2 middle acceleration by faster turning Acc3 max acceleration by faster turning Push button modes btnd send momentary command with LED control value 127 press value 0 release btn send momentary command without LED control value 127 press
21. uantization push button 3 stop scene encoder 4 scene select push button 4 launch scene encoder 5 track select push button 5 start encoder 6 cue volume push button 6 stop encoder 7 master pan push button 7 record encoder 8 master volume push button 8 view arrangement session Setup 29 and 30 are recommended to control parameters of 8 tracks simultaneously setup 29 tracks 1 to 8 setup 30 tracks 9 to 16 Sndl Snd2 Snd3 Snd4 Pan Vol RAC GLob group 1 controls parameter send 1 A for 8 tracks group 2 controls parameter send 2 B for 8 tracks group 3 controls parameter send 3 C for 8 tracks group 4 controls parameter send 4 D for 8 tracks group 5 controls panorama for 8 tracks group 6 Volume and track active for 8 tracks group 7 Rack control of macros to 8 and some rack functions encoder 1 macro 1 push button 1 track view encoder 2 macro 2 push button 2 rack on off encoder 3 macro 3 push button 3 previous rack encoder 4 macro 4 push button 4 next rack encoder 5 macro 5 push button 5 show rack encoder 6 macro 6 push button 6 lock rack encoder 7 macro 7 push button 7 previous track encoder 8 macro 8 push button 8 next track group 8 Global controls encoder 1 tempo coarse push button 1 nudge down encoder 2 tempo fine push button 2 nudge up encoder 3 quantization push button 3 stop scene encoder 4 scene select push button 4 launch scene encoder 5 track s
Download Pdf Manuals
Related Search