V-Series Installatin Manual
Contents
1. T a Wiring Hole Page 5 Initial Mounting m sss Screw Wall Mounting Surface Second Mounting Screw Wall Mounting Surface D 100 F poor shew nial 1 6 Fig 3 D 100 F Speaker Fig 4 Wall D 100 F Door Speaker Mounting Yv Surface Wire runs through opening and into hole Replace Wiring cover TeleDoorBell Installation Guide TeleDoorBell Unit V 200 P 7 LJ LJ LJ L J x Ring On Off Relay Contacts Door Spkr2 Door Spkr1 Tele Line In amp Out Power Plug ae To Door Strike Yellow RJ45 Modular Wire or any activation device Black a PRESS Black q IN RJ31X CA38A Data Jack IN To Door Strike Blue or any activation device 3rd Relay Grey 2o Green Red Use a 22 gauge 4 Doorbell rewiring section This contaci a e Oks is activated Length 250 ft to by pressing door speaker connect from button E controller to speaker RJ11 Modular Wire Supplied with unit Front Door Transformer Alarm jack connection only if alarm monitored TELCOIN LINE from phone company switch and connect o wires together Wire is reconnected to the TeleDoorBell Existing doorbell switch Existing hen Cok to be removed doorbell Transformer Speaker2. 1 Amp Maximum 3 Door Speaker Connecting Jacks Each of these jacks enables a connection to door speaker for communicating to a point of entry 4 Telephone Line Connecting Jack This jack provides connection to the incoming telephone line on the inner pair and connection to household telephone s on the outer pair 5 Power Status LED When ON this lamp indicates the presence of power to the unit when OFF it indicates the absence of power to the unit 6 Power Supply Jack This jack is the connecting point for AC power supply to the unit The supply is typically 16 Vac at a minimum of 250 mA but can be as high as 20VAC which will provide greater ringing power to the telephones Can also use a 16 24 Vdc supply Note Do not exceed 24 VDC or serious damage can occur to the controller unit Installation Instructions To complete the installation the installer must supply the following RJ31X and or CA38A disconnect and bypass jack This is an optional device however it is recommended in the event that the unit needs to be disconnected This will provide a bypass capability whereby the telephone line continues to work if the TeleDoorBell unit needs to be removed from the telephone line Note If installation is done at a location that has an existing alarm jack RJ31X and or CA38A then ensure that the alarm is installed before the TeleDoorBell RJ31X and or CA38A jack Otherwise the alarm system may not have disconnect priority
3. Two plastic wall anchors to mount Door Speaker unit near a point of entry Installation of the system requires that the installer install a 4 conductor wire 22 AWG Max Length 250 from the location of the door speaker unit to the location of the system control unit It is recommended that the system control unit be installed near the point of entry of the customer s main telephone line Please ensure that adequate AC power is available in the general vicinity Mounting of the Door Speaker assembly See Fig 2 IMPORTANT NOTICE For added protection we strongly recommend you use surge protectors on both your power supply and on the C O line phone line to protect against lightning and other energy surges This precaution may be extremely important in rural areas Page 4 Surface mount speaker aa wa diagram ig Installation 1 First drive an initial mounting screw 2 above the door speaker wiring hole leaving about 1 4 of screw shaft extending from wall 2 Thread wire through opening at bottom of unit Note We recommend that you use silicon sealer to protect the wiring around the hole 3 Hang The D 100 F speaker on initial mounting screw 4 Secure the D 100 F speaker to the wall with secondary mounting screw See Fig 3 5 Connect the four wires to the wiring post of the D 100 F speaker See fig 4 6 Replace the wiring cover back on the speaker
4. L4L 8S9 Toll Free 1 888 790 5900 E mail info logenex com For complete information please visit our website at www logenex com
5. 1 Read and understand all instructions 2 Follow all warnings and instructions marked on the product 3 Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 4 Do not use this product near water for example near a bathtub wash bowl kitchen sink or a laundry tub in a wet basement or near a swimming pool 5 Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product 6 This product should never be operated near or over a radiator or heat register This product should not be placed in a built in installation unless proper ventilation is provided 7 This product should be operated only from the type of power source indicated on the marking label If you are not sure of power supply to your home consult your dealer or local Power Company 8 Do not allow anything to rest on the power cord Do not locate this product where the cord will be abused by persons walking on it 9 Do not overload wall outlets and extension cords as this can result in risk of fire or electric shock 10 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product 11 To reduce the risk of electric shock do not dissemble this product but take it to q
6. Connection Remove access cover wire your speaker to the appropriate colour code of the audio terminal side 09 01 Page 6 Additional TeleDoorBell Connection High Speed Phone Line Internet TeleDoorBell Unit V 200 Ring On Off Relay Contacts Door Spkr2 Door Spkr 1 Tele Line In amp Oui Pi T Plu T l R i i TELCO LINE IN slelele Phone Line slelele Demarcation Block Existing Phones on premise Data Filter supplied by internet provider Direct Cable to the Demarcation ck and isolated om the Voice Line High Speed Internet Modem supplied by internet provider In order for the TeleDoorBell to work you will have to isolate the high speed modem from the rest of the regular telephone lines The two ways to go about this is 1 run an independent wire preferably shielded directly to the modem or 2 You could use the existing wire to connect to the modem but only if the wire is isolated from the rest of the phone cables direct run This existing wire if being used cannot be daisy chained or be transmitting any other voice or data information other than the internet connection make sure that you install a Data Filter on the Voice Line to block out any of The high frequency noise Wiring connection for your computer Internet Fax or Answe
7. Installation Manual Revision 5 June 2003 eleDoorBell gt Don t open your door to the unknown TeleDoorBell TeleDoorBell U nit JILA oe RingOn Off Relay Contacts DoorSpkr2 DoorSpkr1 TeleLineln amp Out Power Plug 6A 7500 Martin Grove Rd Woodbridge ON Canada L4L 8S9 Toll Free 1 888 790 5900 E mail info logenex com For complete information please visit our website at www logenex com Page 1 Contents Safety Instructions ANd guidelines cece ceececeeeceeeeceeeeceeeseeeeeaees Pg 2 Ngligelel ie 0 ae meee eet nett tes eeet eee cee eee E ian Pg 3 FS S paana E uteone ata EE OO EEE A E EE REE POS Pans LISI siariyiesnen innean asn ania Ea a Ea EE ESE Pg 3 Installaton INStTruUCONS sssri runna a E Pg 4 Installation Diagram deccemetecdenecteenesctannccegscecsaeanl enmmn saan rauceseensentauca Pg 6 Additional Installation Diagrams ou ccc ccecceecc cece eeceeeeeaeeeeeesaeeseeeeaeeees Pg 7 Tro ble SROOUIG ceesenconseeasctuinreoadotouedtentnanaantdsaaenoadeniesencieeceteeneenetaasess Pg 8 Programming scsicemcapetvoetentesocieneedsncaceunstnnee aaa aa Eaa a EA a aa NEE Pg 9 Warranty Users Guide nannonnnannnnnnnnnnnnsnennnrnnnonenrrrnnrrnrrrnrrnrrerrnnnne pg 9 SAFETY INSTRUCTIONS When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following
8. ble or the touchtone switch may be set to off position 3 Check the yellow wire at both ends of speaker 4 With more than one telephone line you may have wired the controller to the wrong phone line On a gate installation you have no audio communication to the speaker The unit has been designed to go a maximum of 250 ft with a 22 gauge wire Apossible solution to gain an additional 100 ft would be to increase the gauge thickness 18 or 16 You can also double up the Red and Black wires to give it the added gauge A long range system 500 to 1000 ft is now available LRV 200 KSU PBX Installation and requirements for commercial applications We recommend a KSU V200 Controller The unit provides all the necessary requirements to hook up to a commercial phone system including extended phone rings Page 8 User Manual Customers Copy Page 1 of 1 WARRANTY Service Warranty If servicing is needed for the TeleDoorBell please contact your dealer The dealer will be able to direct repairs and or coordinate with the manufacturer TeleDoorBell products are warranted free from manufacturing defects for a period of one year following installation Faulty units will be repaired or replaced at no extra charge to the User except shipping and insurance The manufacturer assumes NO liability for consequential damage or for damage resulting from abuse or improper operation Warranty The TeleDoorBel
9. code from any telephone Will provide toll restriction at the discretion of the owner Rings telephones distinctively when door speaker button depressed Relay closure to ring doorbell or a number of other devices Can be set to ring doorbell only Door speaker has LEDs for constant illumination Supports speakerphone quality conversation between the telephone and the door speaker The system gives a user two minutes to access door following the depression of the door speaker button If the door speaker button is depressed when the telephone is in use on an outside call the user hears a beep tone to alert that there is a visitor at the door The user can then depress 4 on a touch tone telephone to put the telephone call on hold and connect to the door speaker Depressing 4 again will return to the telephone call Note this can only be used once and only after the door speaker button is depressed Alternatively a user can hang up on the telephone call and then pick up the handset and they will be connected to the door speaker This needs to be done within the two minute window can be used beyond the two minutes A DTMF code selection dialed from any connected telephone allows the system user to access the door speaker outside of the two minute window Relay closure activated by DTMF digit 5 or 8 allows door strike dry contact operation Normally Open NO Toll Restriction 1 long distance 011 internati
10. e user s satisfaction Before installing this equipment user should ensure that it is permissible to connect to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection User should ensure that the telephone lines and metallic water pipe system if present are electrical grounded Page 2 Introductions Congratulations on your purchase of the TeleDoorBell a system that offers enhanced security while providing unparalleled convenience The system can be used with or without a doorbell Operation is subject to the following Conditions 1 This device may not cause harmful interference 2 This device may accept any interference including interference that may cause undesired operation Complies with Part 68 FCC Rules FCC REG NO 5ERCAN 31264 OT N REN 0 8B DOC CSA UL approved Features The TeleDoorBell is a telephone based doorbell system that provides the system user with the capability of communicating with a door speaker from any installed telephone set including cordless Unmatched in convenience this unique new product provides the following features System will work as a replacement or in parallel with any standard doorbell Provides high quality audio conversation capability with any connected door speaker Unique telephone ringing when door speaker button depressed Allows homeowner to select the door speaker by entering a unique touch tone
11. efault is 111 applied over the conversation The Hang up doorbell will also ring if enabled 4 can Monitor A Door Station ee eee eee en a a and connect to the door speaker Using q p g seq Pess GAE 4 again will return to the telephone call This hold feature can be used only once Listen Speak per door speaker button depression Hang up Alternatively a user can hang up the active conversation and then pick up the i a Tao receiver and a connection will occur with While speaking to a caller a ak Disable Enable o z 6 Mode the door speaker A user has two VISHOF Bie S68 Wie CAOT DUUON 2 1 976 dialing 9 6 beeps will be heard in your handset Listen for 2 beeps minutes to do this otherwise Disable Enable oj le 1 G Enter New a 2 B needs to be used Press 011 dialing o E E Passcode Speak to person at the door 4 If a door strike system has been f4 REMEMBER The TeleDoorBell will lose its programming and installed to automatically open a door or p to return to factory default settings including a gate a user can activate it by reirme Speaking 1ean password if the power goes out Long Distance Restrictions Change Passcode depressing 5 8 on the keypad while connected to the speaker This will cause a five second contact closure and open the door or gate automatically 6A 7500 Martin Grove Rd Woodbridge ON Canada
12. f both main controller unit and speaker assembly is warranted to be free from manufacturing defects for ONE Year from date of purchase If the main unit and the speaker assembly fails during this period the failed part will be repaired or replaced at no charge f o b Toronto Ontario To obtain warranty repair or replacement you must contact your dealer for instructions Repaired or replaced units will have a ninety day warranty from the time the replacement or repair has been completed International Warranty The warranty for international customers is the same as for any customer within Canada with the exception that PPAL Industries Ltd shall not be responsible for any customs fee shipping charges taxes or VAT that may be due Disclaimer The TeleDoorBell has been designed as a communications device Customer understands and agrees that PPAL Industries will not be held liable for any inconvenience theft and invasion which may be of an indirect cause of the units failure improper installation or the customers ability to use the device PPAL Industries will not be held liable for Telephone Lines being out of service or busy causing the TeleDoorBell to not function properly Although every effort has been made to make the TeleDoorBell as reliable as possible the TeleDoorBelf may fail to function as intended due to the failure of components Conditions to Void Warranty 1 Damage incurred in shipping and handling 2 Damage caused by d
13. isaster such as fire flood wind water rain earthquake lightning and power surges 3 damage caused by unauthorized attachment alterations modifications or foreign objects 4 Defects caused by failure to provide suitable installation environment for the product 5 Damage arising out of any other abuse mishandling or improper application of the product PPAL Industries Ltd 19 Kenview Blvd Unit 31 Brampton Ontario L6T 5G6 CANADA Phone 905 790 8823 or 1 888 790 5900 Fax 905 595 1159 Email info ppalindustries com SS eee eee eee eee eee eee eee SSS eS How to use your TeleDoorBell 1 If your doorbell rings or you hear the unique TeleDoorBell ring signal pick up any telephone in the house within two minutes You can now talk to the person at the entrance 2 If two minutes has expired then pick up any telephone and press on the touch tone keypad on your telephone This will connect you to the door speaker Answering The Door Programming Your TeleDoorBell Note Using can be done at times Pick up hand set Pick wo handset when no one has depressed the door Ick up hand se speaker button and provides the user Speak to person Press with a monitor function If a door strike is connetcted Press Strike 1 apices 3 While on a telephone conversation Listen for 2 beeps depression of the door speaker button will d E cause a unique call indication tone to be j or e SHIKOR baaki S d
14. om the RJ31X and or CA38A data jack which bypasses the TeleDoorBell and connects the phones directly to the main incoming line 2 Check for any breaks in the RJ45 wire including Data Jack When door speaker is pressed phones ring but you have no audio communications to the door 1 Your Green or Yellow wires may be reversed either at the speaker or at the controller 2 The Red and Black wires may be reversed either at the speaker or at the controller The TeleDoorBellis operating but the phones don t ring when the speaker button is pressed 1 Your ringer switch located at the front of the controller may be set to the OFF position 2 The Yellow wire is not properly connected to either the speaker or the controller section of the speaker 3 One of the phones may be causing to much of a load unplug all phones and begin testing with one phone at a time till defective phone is found 4 With more than one telephone line you may have wired the controller to the wrong phone line You have a dial tone feedback at the speaker when door speaker button is pressed Reverse the In and Out on the RJ31X and or CA38A data jack When pressing for monitoring the door you get an operator recording e g this is an invalid number and you have no communication to the speaker 1 You have attached the premise phones in parallel with the TeleDoorBell across your C O line 2 Your telephones may not be touchtone compati
15. onal or 1 976 user programmable Password protection for programming which user can change to a personal 3 digit DTMF code Progress tones to guide user while programming Parts list The TeleDoorBell system is shipped from the factory with the following components TeleDoorBell control unit Speaker Unit with wall mounting plate CSA UL approved class 2 Power Supply Input 120VAC 60Hz Output 16Vac 250 mA Note the system will also work with a class 2 Power Supply Input 120VAC Output 16 24Vdc 350 mA Please make sure that the output does not exceed 24 VDC or serious damage may occur Two 2 modular RJ 11 Male open ended patch cord Used to splice and connect door speaker unit door strike and doorbell to the TeleDoorBell system unit RJ 45 8 pin male to male modular patch cord Three 3 6 wood screws for mounting Dimensions Controller 17cmX17cmX4cm Door speaker 15 5cmX10 5cmX3cm Page 3 Connections Fig 1 TeleDoorBell Unit V 200 1 Telephone ringer Selector Switch This switch enables disables ringing of the telephones When positioned to the left this switch enables ringing of the telephones 2 Doorbell Door Strike Connecting Jack The centre two pins connect to the doorbell button Doorbell will always ring if connected to the unit The adjacent pairs drives the door strike relay or other accessories dry contact triggered devices only Internal TeleDoorBell Relays are all rated at 24Volts
16. ring Machine TeleDoorBell Unit OOL V 200 i Ring On Off Relay Contacts Door Spkr2 Door Spkr 1 Tele Line In amp Out By using the existing wiring already available at the phone jack Use the spare pair and connect these two wires to the Existing Phone Jack Phone T mel etc Jacks Existing Cable CA38A Data Jack RJ45 Modular Wire Supplied with Unit Not supplied Spare Wires a New Phone ac Should you wish to use the answering in ees out Se RJ31X 4 CA38A _ 1 Alarm Jagk 1 1 IN out Connection For Computer Internet Fax Fax Machine Answering Machine Alarm jack connection only if alarm monitored LCO IN LINE from phone company conjunction with the TeleDoorBell then simply connect the machine as you would like the rest of the phones no rewiring required You will require Page 7 Trouble Shooting Guide In case of difficulty try the following suggestions before seeking assistance Problem Controller not responding Solution 1 Check your AC and power adapter confirm LED Power Indicator is ON 2 Check the power connection into the unit My phones don t work 1 Are your phones wired into the RJ31X and or CA38A data jack output To test connection remove the RJ45 wire fr
17. ualified service technician when some service or repair is required Opening or removing covers may expose you to dangerous voltages or other risks Incorrect re assembly can cause electric shock when the appliance is subsequently used 12 Unplug this product from the wall outlet and refer servicing to a qualified service personnel under the following conditions When the power supply cord or plug is damaged or frayed If liquid has been spilled into the product If the control unit has been exposed to rain or water If the product does not operate normally by following the instructions Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will require extensive work by a qualified technician to restore to normal operation If the product has been dropped or the housing has been damaged If the product exhibits a distinct change in performance 13 Avoid using a telephone other than cordless type during an electrical storm There may be a remote risk of electric shock from lightning 14 Do not use the telephone to report a gas leak near the leak DOC NOTICE Notice The Canadian Department of Communications label identifies certified equipment The certification means that the equipment meets certain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to th
Download Pdf Manuals
Related Search