UC-650E+ DVB-S2 Encoder & Modulator User Manual
Contents
1. Status Parameters Encoder Modulator BISS Config Network Save Restore Password Firmware Reboot 2013 12 04 10 57 21 Exit BACKUP CONFIGURATION Backup current configuration to the local file we suggest do this before set the configuration or update firmware LOAD CONFIGURATION Load the backup file to restore your configuration Warning 1 New configuration will replace the old one please backup current configuration before load you use a wrong file the device may not work 2 Please do not turn off the power while file loading otherwise the device will not work Load Config Browse Button Figure 8 26 32 UC 650E DVB S2 Encoder amp Modulator User Manual System Password User can change the password in this interface by first entering current username and password and then entering new username and password to change After inputting the parameters click Apply to save the configuration 52 Encoder Modulator use Web Management 2013 12 04 10 57 28 Exit PASSWORD Status Modify the login name and password to make the device safely forget the Encoder name or password you can reset it by keyboard The default login name and Modulator password is admin Also please note the capital character and lowercase BISS Config character Network User Password Setting Current UserName admin Save Restore Load Backup Current Password2. are single tone modulation and OFF RF Out Single tone modulation off Spec Invert User can switch the Spectrum Invert mode between Normal and Inverted under this menu Spec Invert Normal RF Out Select This sub menu will allow the user to select the output program source The source can be set to the encoding module or ASI input It can only modulate one source at any one time RF Output P Encoder RF 10M Clock The RF 10M Clock reference clock can be switched on or off through this menu RF 10M Clock gt OFF 3 2 5 Network Setting User can press ENTER key to navigate into the network setting and modify the parameters under its corresponding submenus b 5 1 IP Address 5 2 Subnet Mask 5 3 Gateway 5 4 MAC Address 16 32 UC 650E DVB S2 Encoder amp Modulator User Manual 5 5 Reset Password 5 6 Web Manage Port Press UP DOWN to choose one item and ENTER amp LEFT RIGHT to set the desired parameters IP Address 192 168 000 136 Subnet Mask 255 255 255 000 Gateway 192 168 000 001 MAC Address fff fF TFFTEFTTTETTTTE Reset Password Yes NO Web Manage Port 00080 gt NOTE The default MAC address is unique 3 2 6 Saving Configuration User can choose to save the currently configured parameters to memory by pressing ENTER key The system displays following page Save Configuration PF ves NO Saving please wait Eras
3. UC 650E DVB S2 Encoder amp Modulator User Manual SW Version 6 11 HW version 5 8 Web NMS version 2 00 UC 650E DVB S2 Encoder amp Modulator User Manual DIRECTOR IAA aa a duces RP 1 CHAPTER T INTRODUCTION a Near vata naa aule vi DER GER aeui Y ee eu UB e baad Ke aa aoe Son ve ces VR Eo Ce vuv FE 1 BB BOUTIN E T 1 E N E EE 1 1 3 SPECIFICATIONS T 2 TAHINNER BLOCK 2 4 1 6 APPEARANCE AND DESCRIPTION a s seeded oro 4 2 INSTALLATION GUIDE PR CO aANT 5 P PCG FO INGE Coca EE eas 5 2 2 INSTALLATION PREPARATION cans TEE bet PVARE TUR PEE Rx d ER ied 5 2 ANIRE CONNECTION sa foe niai ioieNe 6 24 SIGNAL CABLE CONNECTION E C TT m 7 CHAPTER S OPERATION 5 ue eese dade aves une hada E EUN vacea Fen gua S Ve Rr Ru ue pav ilv re Ure vv uu eden IgE RN a V DNO
4. and then click Login to enter the welcome interface 19 32 UC 650E DVB S2 Encoder amp Modulator User Manual 4 2 Parameter Configuration Summary Status Once logged in users will be given an overview of the device status DVB S2 Encoder Modulator Welcome 2013 12 04 10 52 02 Exit 1 Modulator Software Version 6 12 Build Dec 4 2013 V 1 BISS Config Hardware Version 5 8 m gt System information and Network i l Web Version 2 00 general working status Input l l Save Restore Interface CVBS CVBS Load Backup l Bitrate 9 062 Mbps Ww i Password i Output 1 Firmware Reboot TS Overflow e i i Mmm i Bitrate Act Max 16 127 Mbps Current Out Bitrate 9 014 Mbps User can click any item here to RF Frequency 2000 000 MHz RF Outlevel 10 0 dB enter the corresponding interface to check information or set the parameters Figure 2 Parameters Encoder Clicking Encoder in the left hand column will display program encoding information Users can configure encoding AV parameters in this interface 20 32 UC 650E DVB S2 Encoder amp Modulator User Manual 2 encoding format selection ICH 2 264 HD Encoder Configuration ER 264 v l 2 P Itpez 2 H 264 Vidoe Format Video BitRate i 1
5. 1MQ Floor bearing should be greater than 450Kg m Environmental 5 40 sustainable 0 45 short term Temperature Installing air conditioning is recommended Relative Humidity 20960 8096 sustainable 1040 9090 short time Installing rubber strips for sealing door gaps and dual pane glasses Door amp Windows for windows is recommended Fire Protection Fire alarm system and extinguisher is required Ensure device power air conditioning power and lighting power Power circuits are independent of each other Device power requires DC 12V Please carefully check all power sources before running 2 3 Wire s Connection Connecting the Power Cord User can insert one end into power supply socket while inserting the other end to main power source 0 Before connecting the power to UC 650E DVB S2 Encoder amp Modulator user Caution should ensure power switch is set to OFF 6 32 UC 650E DVB S2 Encoder amp Modulator User Manual 2 4 Signal Cables Connection Input and output signal connection cables are illustrated in this chapter 2 4 1 ASI cable illustration Q 2 4 2 Network cable illustration M 2 4 3 SDI cable illustration v 2 4 4 RF output cable illustration A d 7132 UC 650E DVB S2 Encoder amp Modulator User Manual Chapter 3 Operation The UC 650E DVB S S2 Encoder Modulator be operated using the front panel LCD screen an
6. AAAA nnn nn nnn nn nnn nnn n REBOOT Some configuration will work after reboot the device such as Web Manage Port set Firmware update Figure 11 28 1 32 UC 650E DVB S2 Encoder amp Modulator User Manual Chapter 5 Troubleshooting UPCOM Technologies ISO9001 quality assurance system has been approved by the CQC Organization to guarantee all products quality and reliability UPCOM products must pass testing and inspection before leaving the factory The testing and inspection process covers all the Optical Electronic and Mechanical criteria To prevent potential hazard please strictly follow all operation instructions Upcom Technical support can be contacted by e mailing support upcom com or calling 1 408 329 4158 Preventative Measure gt Installing and operating the device in temperatures between 0 45 C Ensuring proper cooling airflow for the device gt Carefully check the input AC for the proper power supply working range Check all signal cables have been properly connected gt Allow a 10 second interval between alternating power ON OFF states Unplug the power cord if Damaged power cord or socket Any accidental liquid spillage on device Any suspicion of short circuits Physical damage Long term idle periods are planned VV VV ON WV Performing any needed maintenance 29 32 UC 650E DVB S2 Encoder amp Modulator User Manual APPENDIX INTERNAL TEST REPORT OF D
7. DUC VUE 8 T ME GB INNER TRIP mtm 8 Bid Gin bes a HI CREE TIME 9 CHAPTER 4 WEB NMS MANAGEMENT i ee ive se e ee onu kn oh aao aao repa aeos e nya e ape ep aeu eS nean eee a aba eo a oe ao Rae E eue nose 19 Eois re eee ees aan EL E EM CAS MEAM Rc E M DA E M Ra A AS 19 2 2 PARAMETER CONFIGURATION cce i dV SA Sa ausa eve eost Qe eb EE Ce eda eretobn tU eta eb de apo weed Pa EO PA QUE 20 CHAPTER 5 TROUBLESHOOTING ERROR BOOKMARK NOT DEFINED CHAPTER 6 PACKING LIST 5 5 presos o2S eoo OaOE v Pesos ee eee eos ERROR BOOKMARK NOT DEFINED UC 650E DVB S2 Encoder amp Modulator User Manual About This Manual Intended Audience This manual is intended for end users who will operate and integrate the UC 650 Encoder Modulator Some chapters require prerequisite knowledge in electronics and broadcasting technology Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner The contents of this document are subject to revision without notice due to continued progress in methodology design and manufacturing UPCOM shall have no liability for any error or damage of any kind resulting from the use of this document Copy Warning This document includes some confidential information Its usage is limited to the owners of the product that it is relevant to It cannot be copied
8. New UserName inant Password i Firmware New Password Reboot Confirm New Password Figure 9 System Firmware Click Firmware from the menu and it will display the screen as below Here we can update the device by using the update file Click Browse to find the path of the device update file for this device then click on Update to update the device After updating the device we need to restart the device by using Reboot option 2 132 UC 650E DVB S2 Encoder amp Modulator User Manual 52 Encoder Modulator Veb Management 2013 12 04 10 57 36 Exit Status FIRMWARE Warning Encoder 1 Update firmware software and hardware to get new function please Modulator choose the right firmware to update If you use a wrong file the device BISS Confi may not work 3 2 Update will keep a long time please do not turn off the power Network otherwise the device will not work 3 After update you must reboot device manually Save Restore eem Load Backup pdate Firmware Password Firmware Reboot update Figure 10 System Reboot Clicking Reboot from the left hand menu will display the following interface When users click Reboot button it will restart the device automatically DVB S2 Encoder Modulator We 2013 12 04 10 57 45 Exit Status Encoder Modulator BISS Config Network Save Restore Load Backup Password Firmware Reboot
9. display General Status 9 32 UC 650E DVB S2 Encoder amp Modulator User Manual DVB S2 Encoder Modulator System Starting 25 DVB S2 Indicates the modulation standard of this device Encoder Modulator Device name XXX XX MHz Indicates the current output frequency X XX Mbps Indicates the current encoding bit rate Pressing the LOCK key will allow the user to navigate the Main Menu 1 Alarm Status 2 Encode Setting 3 BISS Modulate 4 Modulate Setting P 5 Network Setting 6 Saving Config 7 Loading Config 8 Version Please use the UP DOWN LEFT RIGHT navigation buttons to make any desired changes within the Main Menu 3 2 1 Alarm Status Move the selection cursor to Menu Item 1 and press ENTER If there are no active alarms the LCD screen will display the following Alarm Status No Warning lf alarms are present the LCD screen will display relevant messages For example Alarm Status TS overflow 10 32 UC 650E DVB S2 Encoder amp Modulator User Manual 3 2 2 Encode Setting This sub menu will allow the user to configure Video and Audio encoding parameters P 2 1 1 Video Format 2 1 2 Video Bitrate 2 1 3 Audio Format 2 1 4 Audio Bitrate Thi a 2 1 5 Low Latency sy This function depends on the S model type you purchased The SDI encoding module supports both MPEG2 and H 264 HD SD video formats Move the brackets with LEFT RIGHT keys to specify the intended format and
10. modified or translated in another language without prior written authorization from UPCOM UC 650E DVB S2 Encoder amp Modulator User Manual Chapter 1 Introduction 1 1 Outline The UC 650E DVB S S2 Encoder Modulator is an integrated multifunction device This unit is built around a swappable encoding module CVBS SDI HDMI YPbPr for expanded flexibility One ASI input port is standard Outputs signals can be sent to ASI or L Band RF IF optional ports simultaneously This device can accept input signals from a variety of sources thanks to the available encoding module varieties A user friendly web based graphical user interface allows full remote control from any web browser Broadcasts can be securely encrypted with BISS scrambling This device is built to broadcasting industry standards making it well suited as a high quality and low cost encoding and transmission option for end users 1 2 Features MPEG2 H 264 video Encoding MP2 MP2 AAC MP4 AAC Audio Encoding Optional HD SDI Input pluggable and interchangeable Encoding Modules 1 ASI Input Low Delay achieved Optional Feature Support DVB S S2 RF output and ASI output Output Frequency 950 2150MHz Support BISS encryption Support for a 10MHz reference clock Support Web NMS and front panel LCD amp Keyboard control Firmware Upgrades through web NMS 1 32 1 3 Specifications Input Interface SDI interchangeable with CVBS YPbPr S video HDMI encoding modul
11. user need to scramble the programs mark the corresponding boxes in front of the programs with v and click Set to activate the setting Set 1 TV 1 01 Note When RF Out in Modulator page is selected as Encoder the program s displayed here is from the encoding module while RF Out is selected as ASI the program s displayed here is from the ASI IN 24 1 32 UC 650E DVB S2 Encoder amp Modulator User Manual Parameters Network Click Network it will display the screen as below It displays the network information of the device where to change the device s network configuration if needed 52 Encoder Modulator Welcome to use Web Mana 2013 12 04 10 57 06 Exit Status IP Address Encoder The manage address use this address to visit the manage web The Modulator format is xxx xxx xxx xxx like 192 168 0 1 After set the IP address you must use the new address to visit the manage web NETWORK BISS Config Subnet Mask General is 255 255 255 0 it is must the same in a local area network Gateway Save Restore If the device is in different net segment you must set the gateway Load Backup Web Manage Port Password The default web manage port is 80 if you change it like 8001 you can Firmware visit the manage web only use IP address and port liks as http 192 168 0 1 8001 This function will work after device reboot Reboot Network Setting IP Address 192 168 000 13
12. 1 Modulating FEC Options Mode DVB S2 QPSK QPSK1 2 QPSK3 5 QPSK3 4 QPSK4 5 QPSK5 6 QPSK8 9 QPSK9 10 DVB S2 8PSK 8PSK3 5 QPSK2 3 8PSK3 4 8PSK5 6 8 5 8 9 8PSK9 10 14 32 UC 650E DVB S2 Encoder amp Modulator User Manual DVB S2 FEC P fapski 2 5 Symbol Rate User can navigate to this menu to modify symbol rate allowed range 0 050 20 000Mbps by pressing UP DOWN LEFT RIGHT keys confirm by pressing LOCK key Symbol Rate 17 500 Mbps Roll Off User can enter this menu to select roll off factor Different selections will affect maximum input bit rate Roll OFF gt 0 35 0 25 DVB S2 Pilot The DVB S2 Pilot can be switched on or off through this menu NOTE DVB S2 QPSK or DVB S2 8PSK must be selected as the modulation mode within menu 4 1 to enable this option DVB S2 Pilot On RF Frequency The RF output frequency range is from 950 to 2150MHz with 1K stepping Users then can press LEFT RIGHT UP DOWN button to adjust the frequency and confirm by pressing ENTER button RF frequency 2000 000 MHz RF Output Level The RF attenuation range is from 10db 41 5db After entering this setting submenu user can shift UP DOWN LEFT RIGHT key to set the output level and press ENTER to confirm RF Out Level 10 0db 15 32 UC 650E DVB S2 Encoder amp Modulator User Manual RF Output The RF output mode can be selected within this menu The available modes
13. 4 000 Mbps 1 000 19 500 Mbps 4udio Format Mpez v Audio BitRate 192 Kbps wl i i 7 PO id aca c ME x Audio Video editing area Program Name TV 101 Service ID Ox 101 PID 0x100 Video PID Ox101 Audio PID 0x102 PCR PID Ox 103 i poc EE SERRE Monitoring area Video Format 1920x1080 501 l Encoding a Bitrate 14 751 Mbps Rom Version i 0 0 0 3 i Figure 3 Will pop up additional parameter information Click this button to apply the default setting of Encoder Click this button to apply the modified parameters Parameters Modulator User can click Modulator in the left hand column to navigate into the Modulation interface More details are included in chapter 3 2 4 in this manual 21732 UC 650E DVB S2 Encoder amp Modulator User Manual DVB S2 Encoder Modulator Welcome to 2013 12 04 10 54 01 Exit MODULATOR CONFIGURATION Status TE Config DVB S Modulation Mode s DVB S2 QPSK DVB S FEC 0 52 8PSK DVB S2 FEC Symbol Rate 0 05 20 Roll Off Load Backup DVB S2 Pilot Password RF Frequency 950 2150 2000 00 Firmware RF Outlevel 10 db Reboot RF Mode modulation RF 10Mb Clock Spec Invert normal RF Output Encoder Max input bitrate 16 129 Mbps Valid bitrate 9 098 Mbps Figure 4 DVB S DVB S2 D
14. 6 Subnet Mask 255 255 255 000 Gateway 182 168 000 001 Web Manage Port 20 Figure 6 System Save Restore Click Save Restore from the menu and it will display the screen as below where users can save the configuration permanently to the device Click Save Configuration button to store the data permanently to the device memory By using Restore Configuration users can restore the latest saving configuration to the device By using Factory Set user can set the default factory setting 25 1 32 UC 650E DVB S2 Encoder amp Modulator User Manual 52 Encoder Modulator se Web Management Status Encoder Modulator BISS Config Network Load Backup Password Firmware Reboot 2013 12 04 10 57 14 Exit SAVE CONFIG When you change the parameter you shoud save configuration otherwise the new configuration will lost after reboot LOAD CONFIG Load latest saved configuration after click the Load CFGx then please click the Save CFGx button otherwise the Restore parameter will lost after reboot FACTORY SET Set all configuration back to default after click the Factory Set then please click the Save config button otherwise the default parameter will lost after reboot Figure 7 System Backup Load Click Backup Load from the menu it will display the screen as below DVB S2 Encoder Modulator use Web Management
15. ELAY The values of average delay cover the progress from Encoding end to Decoding end Decoding Terminal DVB T HD STB DVB T HD STB Single Source Interface HDMI Encoding Details Average Bit peo rs Latency Encoding Latency Rate Mode Type ms 1080i 50 720p 50 576i 50 1080i 50 720p 50 576i 50 ode 30 32
16. Manual 1 5 System Connection Sample A V Source Combiner 1 6 Appearance and Description Front Panel Illustration S Rear Panel Illustration 4132 UC 650E DVB S2 Encoder amp Modulator User Manual 10MHz reference clock output interfaces 6 RF output interface Power socket switch fuse Ground pole Chapter 2 Installation Guide 2 1 Acquisition Check End users should check packaging contents against the following list gt UC 650E DVB S2 Encoder Modulator gt SDI Cables gt Power Cord If any item is missing or mismatched with the list above please contact the local vendor 2 2 Installation Preparation Carefully checking for any physical damage during shipping Preparing the correct environment for installation gt gt gt Preparing network connection Signal cables connections 2 2 1 Device s Installation Flow Chart Illustrated as following Connecting Acquisition Installing Connec nung Check Device S etting Running Parameter Device Wire and S ignal Power cable C ord 0 32 UC 650E DVB S2 Encoder amp Modulator User Manual 2 2 2 Environment Requirement Datacenter Ensure a minimum of 1 5M between any two mounted devices Walls Environment should be no closer than 0 8M Electricically Isolated amp Dust Free Volume resistivity of ground anti static material 1X10 1X10 Q Datacenter Floor Grounding current limiting resistance
17. TV 101 12 TV 103 Figure 5 The BISS scrambling function application needs to be matched with BISS descrambler The BISS scrambling supports two modes Mode 1 and Mode E Users can select one of the two modes in the drop down list 23 32 UC 650E DVB S2 Encoder amp Modulator User Manual gt Mode 1 Under Mode 1 the BISS scrambler applies scrambling by a fixed Control Word CW derived from a clear SW Session Word In Mode 1 a fixed 12 digit SW is inserted in the scrambler The 64 bit CW is derived from the SW according to DVB CAS specification Users can select Mode 1 in the drop down menu and then input the 12 digit SW Data in hex The downside device descrambler key equals SW Data on the BISS scrambler side gt ModeE Under Mode E the BISS scrambler completes scrambling through ESW Data and Input ID Input ID is operable when Input is chosen under Select ID The ESW data equals Descrambler key on the downside device side while the input ID equals SK on IRD side Selet ID Device The select ID has two options Device and Input If Users choose Device the Burned Key on IRD side needs to be selected when descrambling while if users choose Input and set Input ID on IRD side users do not need to select Burned Key but to input SK as per Input ID Program Select and Modification User then can click Parse Prg to view the input programs and modify the program names as needed If the
18. d associated control buttons This chapter will explain the menu structure Keyboard Function Description MENU Cancel currently entered value resume previous setting Return to previous menu ENTER Apply setting changes LEFT RIGHT Menu navigation Left Right UP DOWN Menu navigation Up Down LOCK Locks the screen cancels the lock state Saves configuration to memory 3 1 LCD Menu Tree Initializing General Status 1 Alarm Status Error Content 8 32 UC 650E DVB S2 Encoder amp Modulator User Manual 2 1 1 Video Format 2 1 2 Video Bitrate 2 1 3 Audio Format 2 1 4 Audio Bitrate 2 1 5 Low Latenc 2 Encode Setting 2 1 Program 1 This function depends on the SDI model type you purchased 3 1 BISS Mode 2 ESW Data 3 SW Data 4 Input ID 3 5 Select ID 6 Parse Program 3 BISS Modulate UJ UJ CO U1 W J J o mn o lt O O dA ct h NJ T1 lt rm 3 7 Select Program 1 Modulate Mode 2 DVB S FEC 4 Modulate Setting 4 Symbol R ate 6 DVB S2 Pilot RF Frequency 9 RF Output 4 10 S pec Invert 11 RF Out Select 12 RF 10M Clock 5 1 IP Address 5 2 Subnet Mask 5 3 Gateway 5 4 MAC Address 5 5 Reset Password 5 6 Web Manage Port 6 Saving Config 7 Loading Config 7 1 Load Saved CFG 7 2 Load Default CFG 8 Version Version Info 5 Network Setting 3 2 General Setting After successful boot up the device LCD will
19. es 1xASI input BNC interface Encoding Section Video Encoding MPEG2 MPEG4 AVC H 264 Input SDI 1 1920 1080 60P 1920 1080 for MPEG4 AVC H 264 only Resolution 1920 1080 601 1920 1080 50 1280 720 60 1280 720 720 480 601 720 576 50i Bit rate 1 000 19 500 Mbps Audio Encoding MPEG1 Layer Il MPEG2 AAC MPEGA AAC optional as per order Sample rate 48KHz 64kbps 96kbps 128kbps 192kbps 256kbps 320kbps Encoding MPEG1 Layer Il MPEG2 AAC MPEGA AAC optional as per your order Bit rate 1 4 Inner Function Principle Encoding HDMI Optional CVBS Optional ASI ee 2 32 UC 650E DVB S2 Encoder amp Modulator User Manual DVB S S2 Modulation Section DVB S QPSK FEC 1 2 2 3 3 4 5 6 7 8 DVB S2 QPSK FEC 1 2 3 5 2 3 3 4 4 5 5 6 8 9 9 10 DVB S2 8PSK FEC 3 5 2 3 3 4 5 6 8 9 9 10 RF output 950 00 2150 00 MHz 10Khz step IF output 50 200MHz Symbol rate 0 05 20 0Msps Roll Off 0 35 0 25 0 2 Output level 10db 41 5db Output DVB S S2 RF output ASI output as a mirror of RF System Local Control LCD control buttons Remote Control Web based NMS Language English Physical Specification Dimensions 410x460x44mm W L H Temperature 0 45 C operation 20 80 storage Weight 4kgs Power Supply AC 100 240V 50 60Hz gt Oi Choose one output from two input gt es Choose one output from two input UC 650E DVB S2 Encoder amp Modulator User
20. evice supports DVB S DVB S2 QPSK and Modulation mode QPSK DVB S2 8PSK three modes DVB S2 8PSK 1 2 2 3 3 4 under DVB S mode it supports FEC 1 2 2 3 DVB S FEC 5 6 7 8 3 4 5 6 7 8 under DVB S2 QPSK mode it supports FEC 1 2 3 5 2 3 1 2 3 5 2 3 3 4 4 5 5 6 8 9 9 10 DVB S2 FEC 3 4 5 6 8 9 9 10 Under DVB S2 8PSK mode it supports FEC 3 5 2 3 3 4 5 6 8 9 9 10 oymbol Rate range is 0 050 20 000Msps 03502802sdecdg RF out level RF output level ranges from 10db 41 5db 22132 UC 650E DVB S2 Encoder amp Modulator User Manual RF Mode The RF out modes are single tone modulation and off RF 10MHz Clock Enable or Disable 10MHZ Reference Inverts the spectrum Spec Invert Encoder to output the programs from encoding module via RF amp ASI ASI to output the programs from ASI in via RF amp ASI Parameters BISS Config Click BISS Config in the left hand column to navigate into the BISS interface to scramble the programs sourced from encoding module or ASI port 52 Encoder Modulator Welcome to use Web Mana 2013 12 04 10 56 31 Exit Status Encoder BISS SETTING BISS Param Config ESW Data 0x Modulator l BISS Config SW Data 0x 1000000000000 Network Input ID Select ID Device TN TURNER Mode 1 Load Backup Mode E Password EU Apply Save Restore BISS Program Select m Reboot Firmware
21. ing 17 32 UC 650E DVB S2 Encoder amp Modulator User Manual 3 2 Loading Configuration This sub menu will allow the user to load previously saved configurations or revert the device to factory settings 7 1 Load Saved CFG 7 2 Default CFG Loading please wait gt gt gt gt gt gt gt gt gt gt gt gt gt gt gt gt 3 2 8 Version User can check 5 hardware and software version within this submenu Encoder Modulator SW x xx 18 32 UC 650E DVB S2 Encoder amp Modulator User Manual Chapter 4 Web NMS Management The UC 650E DVB S2 Encoder Modulator adopts a web based user interface Before operating user should ensure that the computer s IP address is different from the UC 650E s IP address otherwise it will cause an IP address conflict 4 1 Login The default IP of this device is 192 168 0 136 User can change the IP from the front panel of the device Connect the PC and the device with an Ethernet cable and use ping command to confirm the devices can communicate For example if the PC IP address is 192 168 99 252 user could change the Device IP to 192 168 99 196 to prevent conflicts Enter the device IP in the browser address bar and press Enter t iWeb Management Y 192 168 0 136 Password Default User admin Default Password admin Copyright 2011 Figure 1 Input the user name and password The default Username and Password is admin
22. ode 3 3 SW Data menu will be activated while 3 2 ESW Data and 3 4 Input ID are locked and can t be operated Alternatively if Mode E is chosen as the BISS mode 3 3 SW Data menu will be locked and can t be operated while 3 2 ESW Data 3 4 Input ID 3 5 Select ID are activated and available Mode 1 ESW Data X SW Data SelectID X Input ID X v ESW Data SW Data Select ID Device Input ID Select ID Input Input ID ESW Data amp Input ID Under Mode E with Input chosen in 3 5 Select 10 the BISS 12 32 UC 650E DVB S2 Encoder amp Modulator User Manual scrambler completes scrambling through ESW value and Input ID User can input the ESW data and ID ESW Data 1111111111222222 This menu is operable when Input is chosen at menu 3 5 Select ID Input ID 11111111112222 SW Data Under Mode 1 users can input a 12 digit hexadecimal value SW Data 0x000000000000 Select ID Under Mode E users can choose the ID between Device and nput Under Input Input ID will be operable Select ID gt Device Input Parse Program This menu will display the quantity of programs selected from ASI input Parse Program Get 8 programs gt NOTES This menu will be only available if the 4 11 RF Out Select is set as ASP Select Program Within this menu users can decide which
23. press ENTER to confirm Video Format MPEG 2 264 Enter sub menu Video Bit Rate to adjust the desired bit rate by pressing LEFT RIGHT UP DOWN keys and confirm new values by pressing the LOCK key Bitrate Range 1 19 5 Mbps Video Bit Rate 08 000Mbps The supported Audio formats are MPEG2 MPEG2 AAC and MPEG4 AAC Move the brackets to specify the desired format and press ENTER to confirm Audio Format MPEG 2 MPEG2 AAC Audio Bit Rate can be selected within allowed ranges 64 96 128 192 256 320 Kbps Audio Bit Rate gt 128 Kbps Low Latency to select a latency mode for the content Move the selection cursor to specify a mode and press ENTER to confirm 11 32 UC 650E DVB S2 Encoder amp Modulator User Manual gt Normal Mode 1 h 8j y t The different combination of Video Format Video Bit rate Low Latency Mode and the Resolution of signal source will have an impact on the encoding latency Please refer to the attached Appendix for detailed information 3 2 3 BISS Modulation User can navigate to the BISS encryption settings menu by pressing the relevant front panel control buttons b 3 1 BISS Mode 3 2 ESW Data 3 3 SW Data 3 4 Input ID b 3 5 Select ID 3 6 Parse Program 3 7 Select Program BISS Mode UC 650E supports two BISS modes Mode 7 and Mode E BISS Mode gt Mode 1 gt NOTE If Mode 1 is chosen as the BISS m
24. programs to encrypt Press ENTER to and LEFT RIGHT key to shift v Yes and X No Select Program TV 101 x TV 102 4 gt NOTE When 4 11 RF Out Select is set as Encoder the program s displayed here are sourced from the encoding module While 4 11 RF Out Select is set as ASI the program s displayed here are from the ASI INPUT 13 32 UC 650E DVB S2 Encoder amp Modulator User Manual 3 2 4 Modulate Setting Selecting 4 Modulate Setting in the main menu interface will allow users to set the modulation parameters 4 1 Modulate Mode 4 2 DVB S FEC 4 3 DVB S2 FEC 4 4 Symbol Rate gt 4 5 Roll Off 4 6 DVB S2 Pilot 4 7 RF Frequency 4 8 RF Out Level 4 9 RF Output 4 10 Spec Invert 4 11 RF Out Select 4 12 RF 10M Clock Modulate Mode UC 650E has 3 modulating modes available DVB S DVB S2 QPSK and DVB S2 8PSK Modulate Mode DVB S DVB S2 QPSK DVB S2 8PSK DVB S FEC Forward Error Correction Users can set their desired FEC ratios from within the allowed value range 1 2 2 3 3 4 5 6 and 7 8 gt NOTE This menu will be available if DVB S is selected as the modulating mode within Menu 4 1 DVB S FEC 1 2 DVB S2 FEC Forward Error Correction User can select one DVB S2 FEC ratios from options provided by pressing RIGHT LEFT key gt NOTE This menu will be available if DVB S2 QPSK or DVB S2 8PSK is selected as the modulation mode within menu 4
Download Pdf Manuals
Related Search