LabMax PC Software Installation and Quick Start Guide
Contents
1. LabMax PC Software Installation and Quick Start Guide Moving a File to the USB Flash Drive This tutorial shows how to move a file from the local drive loc to the USB flash drive usb connected to LabMax Attach a USB flash drive to the connector on the side panel Comer SOG 4 MEASURE ML Press the TREND button Press the FILE MANAGER e Soft key and navigate to the loc drive Note The drive loc or usb that opens in FILE MANAGER defaults to the last drive accessed during the previous session or to the loc drive if no USB flash drive is attached to the meter Selection Knob Highlight the file you wa to move Navigate to a folder using the Selection knob if you wish and then press the Press the COPY MOVE soft MOVE soft key key ee Press the ENTER Set button to dismiss the confirmation dialog box The file selected in step 4 has been moved to the usb drive and removed from the loc drive 12 LabMax PC Software Installation and Quick Start Guide Coherent Inc 2 2015 printed in the USA Part No 1175379 Rev AC2. AEN TREND J Selection Knob Block the beam and then press the ZERO button to set the baseline for the new measurement Unblock the beam take the measurement and observe the result on the display LabMax PC Software Installation and Quick Start Guide Measuring Energy With a Pyroelectric Sensor LabMax TOP meter only This tutorial explains how to take an energy measurement using a pyroelectric sensor Connect a pyroelectric sensor to the 25 pin connector and turn the meter ON Note Contact Coherent if the sensor has a BNC plug and did not ship with a 25 pin adapter refer to the Calibration and Warranty section of the User manual for contact information Press the MEASURE button If Watts mode is currently CO COHERENT orrore PL HO selected toggle the UNITS soft key to select Joules mode MEASURE TUNE TREND EN Press the RANGE soft key and then turn the Selection knob to select the range Note Auto range is not available for this type of A sensor Press the TRIG LEV soft key and then turn the Selection knob to adjust the trigger threshold Make sure the trigger threshold is set below the energy level you plan to measure and above the level at which the system triggers on noise Q Take the measurement and observe the result on the d
3. Software Installation and Quick Start Guide LabMax PC Li m o gt COHERENT Software Installation and Quick Start Guide LabMax PC Qi COHERENT 27650 SW 95th Ave Wilsonville OR 97070 LabMax PC Software Installation and Quick Start Guide This document and software is copyrighted with all rights reserved Under the copyright laws this document and software may not be copied in whole or in part or reproduced in any other media without the express written permission of Coherent Inc Permitted copies must carry the same proprietary and copyright notices as were affixed to the original This exception does not allow copies to be made for others whether or not sold but all the material purchased may be sold given or loaned to another person Under the law copying includes translation into another language Coherent the Coherent Logo and LabMax are trademarks or registered trademarks of Coherent Inc All other trademarks or registered trademarks are the property of their respective owners Every effort has been made to ensure that the data given in this document and software is accurate The information figures tables specifications part numbers schematics and software contained herein are subject to change without notice Coherent makes no warranty or representation either expressed or implied with respect to this document and software In no event will Coherent be liable for any direct indirect
4. special incidental or consequential damages resulting from any defects in its documentation GEE simplified S I E Technical English LabMax PC Software Installation and Quick Start Guide TABLE OF CONTENTS Preface ede eo oe aeons ete tox pe o sultesdices M Publication Updates sese V System Requirements senten V Signal Words and Symbols in this Manual vi Signal WOtdS echter Boe ddeet me iet vi Symbols epi RP Rite es vi Software Installation sees 1 Installing Windows XP esee 2 Installing Windows 7 or Windows 8 sess 4 Uninstalling the Software eee 5 Chuck SUI o nocioeitaamecet a A EER 7 Measuring Power With a Thermopile or Optical Sensor 9 Measuring Energy With a Pyroelectric Sensor 10 Saving Data to a File on the Local Drive 11 Moving a File to the USB Flash Drive 12 iii LabMax PC Software Installation and Quick Start Guide LabMax PC Software Installation and Quick Start Guide Preface This guide includes A section that describes how to install or uninstall the LabMax PC software e Aseries of mini tutorials that shows step by step instructions on connecting a sensor to your LabMax meter taking measure ments and saving data for later viewing For complete operatin
5. all the software automatically Recom mended on the following screen and then click Next Found New Hardware Wizard Thus ward helps you install software foc Coherent LabMax M your hardware came with an installation CD LE or floppy disk insert it now What do you want the wizad to do nstal the soltware automatically Recommended natal from a ET or specific ocasion Advanced Chick Next to continue lt Back meno conce Note If a window similar to the one shown below appears click the Install this driver software anyway radio button to continue the installation w See desi Step 4 Follow the rest of the on screen instructions to complete the installation For complete operating instructions refer to the LabMax User manual available in Adobe PDF format on the CD ROM that shipped with your product LabMax PC Software Installation and Quick Start Guide Installing Windows 7 or Windows 8 NOTICE Install the LabMax PC software before you connect the meter to the computer Step 1 Insert the LabMax CD into your CD ROM drive If Autorun is enabled on your system installation will start automatically otherwise double click the LabMax setup exe file in the folder that appears on the desktop Note If a window similar to the one shown below appears click the Install this driver software anyway radio button to continue the installation Step 2 Follow the on screen instructions to com
6. ata for later viewing Tutorials include Measuring power with a thermopile or optical sensor p 9 LabMax TOP meter only Measuring energy with a pyroelec tric sensor p 10 Saving data to a file on the local drive p 11 Moving a file to the USB flash drive p 12 WARNING Follow all laser safety procedures The laser must be blocked or switched OFF before starting any of the procedures described in this section WARNING Power to the LabMax meter must be OFF before starting any of the procedures described in this section LabMax PC Software Installation and Quick Start Guide NOTICE Do not exceed the power energy density limits of the sensor LabMax PC Software Installation and Quick Start Guide Measuring Power With a Thermopile or Optical Sensor This tutorial describes how to take a power measurement using a thermopile or optical sensor Press the RANGE soft key and then turn the Selection knob to select the range Select Auto if you want the meter to select the best measurement range for you and turn the meter ON Connect a thermopile or optical sensor to the 25 pin connector Note Contact Coherent if the sensor has a BNC plug and did not ship with a 25 pin adapter refer to the Calibration and Warranty section of the User manual for contact information Press the MEASURE button GS COHERENT eese ADMD 200 MEASURE k TUNE
7. g instructions refer to the LabMax User manual available in Adobe PDF format on the CD ROM that shipped with your product Publication Updates To view information that may have been added or changed since this publication went to print connect to www Coherent com System Requirements e 600 MHz or faster processor e Microsoft Windows XP Windows 79 32 or 64 bit or Windows 89 32 or 64 bit e 512 MB of RAM 190 MB of free hard disk space CD ROM drive USB and or RS 232 port 1024 x 768 screen resolution LabMax PC Software Installation and Quick Start Guide Signal Words and Symbols in this Manual This documentation may contain sections in which particular hazards are defined or special attention is drawn to particular condi tions These sections are indicated with signal words in accordance with ANSI Z 535 6 and safety symbols pictorial hazard alerts in accordance with ANSI Z 535 3 and ISO 7010 Signal Words Two signal words are used in this documentation WARNING and NOTICE WARNING Indicates a hazardous situation that if not avoided could result in death or serious injury NOTICE Indicates information considered important but not hazard related Symbols This symbol is intended to alert the operator to the presence of exposure to hazardous visible and invisible laser radiation Vi LabMax PC Software Installation and Quick Start Guide This symbol is intended to alert the ope
8. isplay 10 LabMax PC Software Installation and Quick Start Guide Saving Data to a File on the Local Drive In this tutorial you will create and save data to a file that s stored on the local drive loc The tutorial on p 12 shows how to move a file to the USB flash drive You can also save data directly to the USB flash drive by navigating to the USB drive in step 2 in the following illustration Press the TREND button C3 n3 Q conerent LabMax To Laser Poser Energy Meter eoo measure M Tune TREND X A Press the SAVE soft key Press the CREATE FILE soft key Press the FILE MANAGER soft key and navigate to the loc drive Note The drive Joc or usb that opens in FILE MANAGER defaults to the last drive accessed during the previous session or to the loc drive if no USB flash drive is attached to the meter aa 7e Press the EXIT soft key Press the TREND SETUP Soft key Set the Duration value to the sample size you want to save to file Create a file name on the TREND Name Log File screen Press the SAVE soft key Press the START soft key When data collection is complete press the RESET Soft key Data is now saved in the file previously created in step 8 11 eo0 measure taser Power eneray merer BMAX OP conerent
9. plete the installa tion For complete operating instructions refer to the LabMax User manual available in Adobe PDF format on the CD ROM that shipped with your product LabMax PC Software Installation and Quick Start Guide Uninstalling the Software Use this procedure to remove the software from your computer l 3 Click the Start button in Windows to display the Search box gt All Programs Click Uninstall a program under Control Panel Control Panel 4 Uninstall a program qetrTEnove a program i Uninstall a gadget amp Programs and Features Documents 1 E Software Running htm Microsoft Outlook 21 I ACTION ITEM CREATE TROUBLESHOOTING GUIDE E PowerMax troubleshooting docx ACTION ITEM CREATE TROU A PDF Converter 5 Activation Key problem Incident 110504 0008 P See more results uninstall a program LabMax PC Software Installation and Quick Start Guide There are two files you must uninstall Coherent LabMax ActiveX Control and Coherent LabMax PC v1 7 1 0 Double click each file name one at a time and then click the Yes button to confirm the deletion Unventall or change program te meet anum win A om he he ent nci innt Charge Papar LabMax PC Software Installation and Quick Start Guide QUICK START This section presents mini tutorials that describe how to connect a sensor to your LabMax meter take measurements within minutes and save your d
10. rator to the presence of important operating and main tenance instructions Vii LabMax PC Software Installation and Quick Start Guide viii LabMax PC Software Installation and Quick Start Guide SOFTWARE INSTALLATION This section describes how to install LabMax PC software and drivers or uninstall the software Installing Windows XP p 2 Installing Windows 7 or Windows 8 p 4 Uninstalling the software p 5 LabMax PC Software Installation and Quick Start Guide Installing Windows XP NOTICE Install the LabMax PC software before you connect the meter to the computer Step 1 Insert the LabMax CD into your CD ROM drive If Autorun is enabled on your system installation will start automatically otherwise select Run from the Start menu and then type D setup exe substitute the appropriate letter of your CD ROM drive for D Step 2 When the following screen appears select No not at this time and then click the Next button to continue the instal lation Found New Hardware Wizard Welcome to the Found New Hardware Wizard Windows wil search for curent and updated software by looking on your computer on the hardware installation CD ot on the Windows Update Web site with your permission Read ou pevacy policy Can Windows connect to Windows Update to search loi software Click Newt to continue rc E l LabMax PC Software Installation and Quick Start Guide Step 3 Select Inst
Download Pdf Manuals
Related Search