RINK Model 1622 Series number:
Contents
1. 1622 s ee Tension the conveyor belt if slipping Release the locking nut 1 on each side Gradually tighten the nuts 2 by 1 2 turns on each side at a time in a clockwise direction Secure the locking nut 1 on each side back into place A Over tensioning shortens the service life of the conveyor belt 214 1622 15 1622 Installing and removing the conveyor belt Relax the conveyor belt by releasing the tension screw 1 gradually and evenly on each side Remove the belt transmission by releasing the screw 6 on the front end Remove the eccentric ring 8 on the flange bolt 9 on each side and unscrew the flange bolt on each side Remove the eccentric bearing 11 on the flange bolt 12 on each side Remove the flange bolt 12 with the tension screw 1 on the right hand side Release the screws 10 on the right side and remove the intermediate roller bearing 3 Release the screws 10 on the left side Remove the front 2 and rear belt rollers 5 and the intermediate rollers 4 Pull the conveyor belt out towards to the rear Installation is carried out by the same steps in reverse order bo LOU S 2S9t21 55 Ze SS LER Tension the conveyor belt after installing With the conveyor belt relaxed mark a length of 500 mm on the conveyor belt on both sides Tension the conveyor belt2. 1622 A SAFETY REGULATIONS A The permissible vertical load of the towing vehicle must be observed Before starting the engine check the immediate surroundings and ensure adequate visibility During operation no persons should be within the danger zone of the spreader as there is a risk of injury from rotating parts and flying debris Pay attention to suitable clothing Wear safety shoes and full length trousers Long hair must be tied back Do not wear loose items of clothing Use appropriate personal protective equipment in accordance with applicable health and safety regulations The RINK Topdresser 1622 produces a noise level of 74 dB a in the immediate vicinity of the brush roller Wear certified hearing protection when working with the machine Adjustment and repair work may only be carried out by authorised personnel Before beginning repair work on the hydraulic equipment ensure without fail that it has been depressurised Inspect hydraulic hoses regularly and replace them if you find defects or alterations Hydraulic hoses must meet the technical requirements of the equipment manufacturer Spent oil endangers the environment please dispose of it in an environmentally sound manner 1622 5 BRIEF DESCRIPTION The RINK Topdresser 1622 is designed for spreading fine grain and loose scattering materials such as sand gravel granules and similar materials The topdresser s diffuser 1s driven by a gearbox with
3. a hydraulic motor for the conveyor belt and a hydraulic motor for the brush roller The rotational speed of the hydraulic motor for the conveyor is infinitely variable via a flow regulator This allows the scattering material to be dosed accurately The scattering density or spread rate can be determined by driving speed the rotational speed of the brush roller and the conveyor belt speed TECHNICAL SPECIFICATIONS Dimensions Indi 2 70 m Tr TS 2 30 m PACT HUS unte 1 95 m Bridie 1 85 x 2 01 m ur EM max 2 50 m Weights Permissible total Welglit Ec ix 4500 kg P rmissibl axle TOO iiie oS tte atu 4000 kg Permissible sues n o e 500 kg Emp elg D etam ebbe te Seo qe poner ake 1000 kg Track oale ecu EM o E dU 1360 mm dors C 520 50 17RibTrailor 2 0 bar Permissible max 25 km h Tractor DOWOFE osten d Ru min 26 KW 35 PS eee ee ee ene Tee infinitely variable Hydraulic connection values Minimum flow towing vehicle 25 min Minimum pressure towing vehicle 140 bar The identification plate is located on the front of the spreader on the right hand side 6 1622 FIRST TME USE Tighten
4. into place Fill with Plantosyn 3268 ECO up to the centre in the sight glass 5 Screw the filler plug 6 back into place This is a closed hydraulic circuit To prevent impurities from entering even so the A return filter 7 must be replaced after 100 hours of use Spent oil endangers the environment please dispose of it in an environmentally sound manner 1622 19 REPLACEMENT PARTS RINK Topdresser 1622 Address for ordering replacement parts Fout Verwijzingsbron niet gevonden Ordering replacement parts So that your order for replacement parts can be processed swiftly it is essential for the following information to accompany every order Chassis number or identification number Year of manufacture if available Parts numbers from the relevant replacement parts list Name of part s Order no Example order 529413 201227 Pillow block bearing 25 mm 10133 Chassis no Year of Parts no Name Order no manufacture 20 1622
5. OPERATION MANUAL REDEXIM AND LIST OF PARTS 3709 JA Zeist RI N K the Netherlands 1 31 30 6933227 F 31 30 6933228 M O d el 1 62 2 E com series number www redexim com WARNING IN ORDER TO ENSURE SAFE USE OF THE MACHINE AND OPTIMAL RESULTS IT IS ESSENTIAL TO READ THIS OPERATION MANUAL CAREFULLY BEFORE BEGINNING TO OPERATE THIS RINK MACHINE 1325 English 933 120 420 EC DECLARATION OF CONFORMITY Manufacturers or importer s Certificate of Compliance for RINK Topdresser1622 The undersigned Rink Spezialmaschinen GmbH 88279 Amtzell Deutschland Germany hereby declares that the machine specified below complies with all relevant provisions of the Machinery Directive 2006 42 1 Machine name RINK Topdresser 1622 2 Manufacturer or importer Rink Spezialmaschinen GmbH WangenerstraDe 20 88279 Amtzell 3 Model 1622 4 Machine Series number 5 Year of manufacture j rf fff F f Ai 8 H WP Amtzell date Uli Bachmann 1622 TABLE OF CONTENTS EC DECLARATION OF CONFORMITY ccce eee eee ee eee e eee eoo o ooo eee ee eese tete eee eee 2 SAFETY REGULA TIONS 4 5 BRIEF DESCRIPTION iie Pe eei deep dise AE iicet iv a T 6 TECHNICAL SPECIEICATIONS Pese Ebo Eee ds Perses 6 FIRST IIMB USE itr tbe Ebr b ED
6. TO speed or oil temperature that is too low will impair scattering performance Check oil level on the hydraulic tank centre in sight glass before starting work On leaving the factory the hydraulic system is filled with the hydraulic oil Plantosyn ECO 3268 Too little oil can cause damage to or destruction of the hydraulic pump Crank up the support wheel lifting the safety flap Lay the hydraulic pumps such that they do not scrape the ground or rub against the towing vehicle Detach in reverse order A Before detaching depressurise the hydraulic system on the towing vehicle Loading Attend to the desired maximum ground pressure see Technical specifications When loading pay attention to the permissible total weight Ensure uniform loading 1622 SCATTERING Operating controls The brush roll speed can only be regulated by adjusting the tractor rpm 1 Regulator for adjusting the conveyor belt speed on a scale of 0 to 10 S po VN f ur PN ETSI gt EN p Fd c X NN 2 Sl a a c p Y S RE ui NR i 2 S 5 S AN P Set scattering thickness The scattering thickness 1s dependent upon the speed of the towing vehicle the speed of the brush roller tractor rpm the speed of the controller for the conveyor belt 1 1622 CARE and MAINTENANCE Grease the bearings with all purpose grease after every 50 hours of us
7. afety regulations and have not been made aware of the dangers involved Every person who has been commissioned by the user to operate service and repair the spreader must have read and understood the user manual and in particular the section Safety Regulations Only the Manufacturer s original replacement parts must be used for repairs As well as the instructions in this operation manual the generally applicable Safety and accident prevention regulations are to be observed When using public roads the respective provisions road traffic regulations apply The transportation of persons is not permitted Stepping onto the loading bridge whilst the spreading equipment is running is prohibited A corresponding notice has been stuck onto each side of the RINK Topdresser 1622 These notices must be legible at all times and must be replaced if they become damaged The operator is obliged to inspect the RINK Topdresser 1622 before using it for visible signs of damage and defects Alterations in the RINK Topdresser 1622 including its operation which could have adverse effects on its safe operation must be rectified immediately For safety reasons it is expressly prohibited to make alterations or additions to the RINK Topdresser 1622 If any modifications to the RINK Topdresser 1622 are undertaken then the CE mark that is valid for the machine becomes invalid and must be independently renewed by the person who has made such modifications
8. cssssesavavavavsvscssscesssssesscsavavavavacassenensesessssasavavavavassenenenss 18 REPLACEMENT PARTS iccessssscuiccasessansuseveldaacsecabsdedcabacdvanssnsuveresceacsecansseucubacdvavssacuserestausaeese 20 Address fOr ordering replacement parts oe eoo eno eese sede eod pudo due 20 RINK Topdresser 1622 Fout Bladwijzer niet gedefinieerd belt component COMP Cle iu oi usato etd pd vv Fout Bladwijzer niet gedefinieerd Scatterime Toller COMPIE e tenta pi e Fout Bladwijzer niet gedefinieerd Technical alterations reserved 1622 A SAFETY REGULATIONS A The RINK Topdresser 1622 is built exclusively for spreading fine grain and loose scattering materials such as sand gravel granules and similar materials Any other usage is considered to be improper The manufacturer is not liable for any damages incurred as a result the user alone carries the responsibility for the risk involved The intended use also includes compliance with the manufacturer s specified operating maintenance and repair requirements The RINK Topdresser 1622 is built in accordance with the latest technological specifications and is safe to operate However RINK Topdresser 1622 can present a danger to life and limb to the user and others if it is operated serviced and or repaired by any persons who are not familiar with the s
9. e 1 Bearings on both sides of the brush roller 2 Bearings on both sides of the rear transport shaft 3 Bearings on both sides of the front transport shaft Bearings without grease nipples are maintenance free zm 1622 Change oil on conveyor belt gears after every 100 hours of use Unscrew the filler plug 1 Release the draining plug 2 on the inside at the bottom and drain the oil away Screw the draining plug back into place Hill with gear oil EP140 up to the check screw 3 Screw the filler plug back into place Spent oil endangers the environment please dispose of it in an environmentally sound manner 4 Ke S N f NN IM M AN KC OAK X AM Qe 2 _ d d EN 7 S P N IN N E 2 1622 11 Service axle after every 100 hours of use A Servicing work on the axle must only be carried out by authorised specialist personnel Tighten wheel nuts Check the wheel hub clearance and adjust if necessary Check the brake setting Check the brake pad thickness min 3mm and get the brake pads renewed if necessary 12 1622 Set the brush roller distance when required Release the two screws 1 on both sides of the brush roller Lower the brush roller until it slightly touches the conveyor belt Secure the screws 1 back into place
10. e Putas Ub eov obe P n Pub E cw PE EIER 7 OPERA TION Pere 8 USC lt a ea T EO cmm centes 8 deta MIME 8 NUN UE EES EO ETEA 8 SOA W DI Cd lo Coe c d RR MEE RON 9 OPD CONTOS Eo E E Last M cave ohana 9 DEE seatterme acie i totis Ae ut Ded ce SL 9 CARE and MAINTENANCE 10 Lubricate bearings with all purpose grease after every 50 hours of 10 Change oil in conveyor belt transmission after every 100 hours of 11 Service axle after every 12 wisi brush Toller ASTU red MET eee 13 Tension conve vor Dell nt SBppIng pedea Neb Sem genes ee Mu ME UR UE UM MU EUR 14 Installine and TeiMmo vine conve OF iude esie besten dent E E A 16 JTenstonconve vor after ANS Al NING sui cube ocu dc E 16 External oil supply ccssecscscscssscssssesessssccavsvscscscscses
11. on both sides evenly using the two tension screws see page 13 until the marked length is stretched to a maximum of 502 mm Allow the conveyor belt to run for 30 mins until it runs centrally between the side guides adjusting it 1f necessary 16 1622 The conveyor belt must not touch the side guides as this will damage it During readjustment gradually adjust the conveyor belt tension on the side on which it is touching the side guides Over tensioning shortens the service life of the conveyor belt 1622 17 External oil supply Change oil in the attachment pump after every 100 hours of use Unscrew the vent screws 1 Loosen the draining plug 2 at the bottom and drain the oil away Screw the filler plug back into place using a new seal Rotate the gear by 180 degrees Fill with oil SAE 120 to 140 up to the level of the sight glass 3 Screw the draining plug 2 back into place using a new seal Spent oil endangers the environment please dispose of it in an environmentally sound manner 1 Art no nu 2 Art no 3 Art no 4 Art no A 5 Art no 6 Art no 7 Art no 16057 1 16057 2 16057 3 16057 4 10842 10840 2 10722 18 1622 Change oil in hydraulic tank when required Unscrew the filler plug 6 Release the hose 4 and drain the oil away Screw the hose back
12. wheel nuts Check wheel hub clearance and adjust if necessary Check tyre pressure A Inspect these items again after the first run under load 1622 OPERATION Before each use Inspect the RINK Topdresser 1622 for visible defects Rectify defects Check tyre pressure Inspect the running track of the conveyor belt and adjust where necessary The conveyor belt must not touch the sides Attachment and detachment Secure the RINK Topdresser 1622 in standing position with wedges to prevent it from rolling Attach the RINK Topdresser 1622 to the towing vehicle Establish hydraulic connection the pressure pipe is lying on the right in the direction of travel the return pipe is lying on the left in the direction of travel Oil circulation is required On leaving the factory the hydraulic system is filled with the hydraulic oil Plantosyn 3268 ECO For external oil supply see page 15 insert the attachment pump into the PTO shaft on the tractor and secure it against rotation using the integrated torque arm The PTO must be turned on only at idle since the activation of the PTO run under load can cause a fracture of the connection pinion between the transmission and the pump For optimal operation the PTO speed should be approximately 450 l min corresponding to 25 1 min The oil temperature at the start of work should be about 25 C sight glass on the oil tank or if necessary allow the hydraulic system to warm up P
Download Pdf Manuals
Related Search