Brivis Iceberg Evaporative Cooling Owners Manual
Contents
1. are directing air flow across the ceiling and not towards the floor If it is humid run the system in FAN ONLY mode Check sufficient doors and or windows have been opened Refer to Exhaust section Model Number For Your Records Serial Number Install Date Installed by Installer Contact Service Records To arrange a visit from one of our certified technicians please contact the Brivis Service department on 1300 BRIVIS Service Provider Contact Number Service Year 2 Service Date Service Year 4 Service Date 7 Service Year 6 Service Date Fi Service Year 8 Service Date Service Year 10 Service Date Warranty and Maintenance Registration Brivis Customer Care Program The Brivis Customer Care Program is designed to help you get the most out of your new cooler We may contact you before each winter or summer season with some preferential offers for preventative maintenance services which will keep your Brivis cooler in great condition Please note Preventative Maintenance Services are chargeable and not covered under your product warranty Your cooler needs to have reasonable and safe access and be installed inline with the installation instructions supplied with the cooler An extra charge may apply if Brivis is required to allocate two service personnel to enable compliance with safety regulations Cooler2. in This is quite normal and will dissipate quickly as the new pad is constantly flushed during use Ventilation Openings Required Table 1 Opening required for each model Highest Lowest Fan Fan Setting Setting Number of average size windows amp doors suggestions only Three sliding windows or one door amp two hinged windows XQ4 Average ventilation area provided by various openings when fully opened Open Sliding Window 0 7m Hinged Window 0 3m Note You can also choose to have these openings only halfway open Please note the opening will only provide half the amount of ventilation shown above and more openings would be required To cool your whole house you need windows and or doors open throughout the house If you wish to concentrate your cooling to a select area simply concentrate all the required ventilation in the targeted area See following illustration On hot windy days ensure that the windows and or doors open for ventilation are on the sheltered side of the house Note Ceiling exhaust vents security relief vents are not recommended as recirculating air will impair the performance of the cooler Illustration shows method of getting effective cooling in the desired areas of the home Evaporative Air Conditioner Closed windows This area concentrated cooling Cooled air flow
3. s statutory rights and the rights given by this Warranty all of the warranties and all liabilities of Brivis for any direct special indirect or consequential loss or damage any damage or expense for personal injury or any loss or destruction of property arising directly or indirectly from the use or inability to use the Product or any of its parts and servicing the Product are expressly excluded 14 6 2 6 3 Travel Transport amp Access Costs The Purchaser must pay freight charges in transit insurance expenses and travelling costs for repairs replacements under this Warranty that are required to be performed 100km or more from the nearest Brivis branch or Authorised Service Representative Subject to clause 6 3 Brivis will pay freight charges in transit insurance expenses and travelling costs for repairs replacements that are required to be performed less than 100km from the nearest Brivis branch or Authorised Service Representative In this circumstance a Brivis will arrange for such repairs replacements and make any payment directly to the third party to provide the freight in transit insurance or travel services or b if Brivis considers appropriate it will authorise the Purchaser in writing to pay for the relevant freight charges in transit insurance expenses or travelling costs and then upon provision by the Purchaser to Brivis of a tax invoice showing those costs have been incurred reimburse the Purchaser for such co
4. substances f Product which has been installed in a portable or mobile building structure or application including but not limited to a caravan or boat g Product which is being re installed at a location other than the original site h any consumable item supplied with the Product including but not limited to an air filter battery fan belt igniter or cooler pad i installation of third party components that may be attached to the Product These include but are not limited to control wiring ducting return air filter s grille register diffuser zone motors controls thermostats pipe work and fabricated or added components These items remain solely the responsibility of the Qualified Installer i installations where electrics electronics may be subjected to moisture chemicals e g swimming pools or nurseries k any repair which is needed as a result of an accident misuse abuse or negligence l Product that is utilised in an environment indoor and outdoor outside its specified operating range and m fair wear and tear to the Product Limitations Product fitness for purpose and overall system design sizing and application are not the responsibility of Brivis This includes but is not limited to the heat load calculations airflow and system balancing This Warranty does not apply to any Product installed at an Installation Site which is outside Australia or New Zealand Except where inconsistent with the purchaser
5. turn OFF If the cooler is OFF you can pre set the timer for the cooler to turn ON The timer is set in 1 hour increments ranging from 1 to 17 hours Setting the timer to turn system ON System must be in the OFF state Press the Power D button until the blue LED is off and OFF is displayed on the LCD screen Push TIMER button to enter timer setting mode Press the and W buttons to adjust ON time Press the TIMER button to save timer setting Ch es HN Controller will return to the OFF screen and time until on will be displayed e g ON IN 4 00 Setting the timer to turn system OFF 1 System must be running in the desired operating mode i e AUTO COOL MANUAL or FAN ONLY Push TIMER button to enter timer setting mode Press the and W buttons to adjust OFF time Press the TIMER button to save timer setting Chi besito Dio Controller will return to previous ON mode setting and time until OFF will be displayed e g OFF IN 4 00 Brivis Customer Care Program Brivis products are renowned for providing years of trouble free performance However that doesn t mean that they will perform at their peak all of that time without some attention To be at their most efficient they like most things need a little care So to ensure that every Brivis unit is always in perfect condition we have established the Brivis Care Program for our valued customers When you are a member of our Care Program you will receive
6. with product specific manuals 13 2 2 2 3 2 4 3 2 4 5 2 5 3 Brivis will determine in its sole discretion which classification the Product fits into and the corresponding Warranty that shall apply An Authorised Service Representative will repair or replace at its option the Product or any part of the Product that its examination shows to be defective The repair or replacement shall be performed during Normal Business Hours by an Authorised Service Representative Repair by persons other than an Authorised Service Representative may void the Warranty The Warranty of the Product requires that in addition to all other conditions the Purchaser conducts regular and or preventative maintenance as may be specified by Brivis e g Operating Instructions and required by the level of usage and the usage environment including the use of correct and uncontaminated refrigerants and lubricants Conditions of Warranty The Purchaser may only obtain the benefit of the Warranty if the Purchaser d maintains and services the Product in accordance with the instructions set out in the service section of the relevant Service or Owner s Manual b complies with clause 7 below titled Purchaser s Responsibilities notifies Brivis within 30 days of a defect developing that a claim is being made under this Warranty and d provides in support of the claim made under this Warranty a Proof of Purchase This document repr
7. BRIVIS ICEBERG COOLING Owner s Manual PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE Index 1 Privacy Notification How does your evaporative cooling work Before operating your Brivis Evaporative Cooler Safety Wamings liiis sess 2 The air smells a little different Why Openings Required Operating your evaporative cooler 3 Start up Shut down On humid days Ceiling Vents Location Operating your Programmable Wall Control 4 5 Automatic Pre Wet Operating Modes 1 AUTO COOL Mode 2 MANUAL Mode 3 FAN ONLY Mode Timer Function Brivis Customer Care Program 6 8 Cooler Service amp Maintenance Before you call for Service or Assistance Troubleshooting For Your Records Service Records Warranty and Maintenance Registration 9 Brivis Customer Care Program Cooler Warranty Card Form Cooler Customer Questionnaire 10 Frequently Asked Questions 11 12 Terms 13 15 Introduction Congratulations on your purchase of a Brivis Cooling system For you to achieve the performance and efficiency expected from your new cooler please ensure the installer is a qualified trades person that the installer has commissioned the unit before you commence operating and you take the time to read the contents of this manual In some Austral
8. Warranty Card Form please return in reply paid envelope provided For Australia please return in reply paid envelope For New Zealand please return to Warmair PO Box 38523 Wellington Mail Centre Site Details Name Postal Address Site Address if different to above State Country Post code Home phone no Work phone no Mobile phone no Cooler Purchase Details Cooler Model Date of purchase Installation company Serial No Cooler Customer Questionnaire Please tick the appropriate box e Have you been given a certificate of compliance Yes No Number What type of home do you live in Single Storey Double Storey L Split Level e What type of roof do your have Tile Metal U Other 10 Frequently Asked Questions Q A gt How often should the cooler be serviced Brivis recommend the cooler is serviced every 2 years at a minimum to ensure it operates at peak efficiency Please Note Due to environmental conditions the cooler may need to be serviced every year What is done in a service Check filter pad material for holes or deterioration The pads will deteriorate over time and lose their water absorption ability Replace pads as required Clean the tank and internal surfaces Clean the filter pads and flush water With the filter pads in position switch ON the power supply isolating switch and opera
9. a courtesy call regarding maintenance service to your unit This service includes cleaning the unit and ensuring that the system is operating at maximum efficiency Not only does this guarantee peak performance it also allows any minor problems to be detected early Which ensures that the system will always be ready when you need it If something needs more than just maintenance it can be attended to at the time of the service additional charges may apply This repair will be guaranteed for 3 months labour and 12 months parts Cooler Service amp Maintenance To ensure that your Brivis cooler continues to operate at peak efficiency it should be serviced at two year intervals by an authorised person trained in the service of Brivis coolers please contact our National Care Centre for authorised Brivis Service Technicians Refer to the back of this manual for contact details Brivis Iceberg coolers are fitted with a mesh over the inlet to the unit To maintain the cooler s performance the mesh must be inspected amp cleaned at regular intervals depending on the amount of use of the unit amp the environment in which it operates The same applies to the Brivis lcecap mesh where fitted refer to below image This service of the cooler unit will include all maintenance and adjustments required to the following components to ensure your cooler runs at its peak efficiency e Trough Electronic Controls e g Sensors Fan and Pump Assem
10. ation rate of the coolers pads The more water the cooler can evaporate for a given condition and airflow the more cooling potential the cooler has The evaporation rate varies depending on the current weather conditions the size of the cooler the speed of the coolers fan or the velocity of the air through the pads and the condition and type of the filter pad material In addition to the cooler evaporating water water is also displaced to maintain the water quality within the cooler so that the coolers pads and other components do not deteriorate prematurely How much water does the tank of my cooler hold Model Tank Capacity litres Brivis Iceberg XQ4 12 Can run the system when am not home Evaporative cooling relies on doors and or windows being open so you can run it when you are not home provided you have the required ventilation openings 11 gt gt gt gt gt gt gt gt gt gt gt Frequently Asked Questions cont d How many doors and windows should have open Refer to the section on openings required The table gives a guide to the amount of opening area required in m2 and also gives suggestions on how to provide this Why is there condensation and moisture on my tiles Make sure the vents are directed across the room and not towards the floor Make sure sufficient doors and windows are open Refer to the section on openings require
11. bly Pads and Water Distribution Module Inlet mesh e Air intake vents e g Brivis lcecap mesh i Brivis Icecap mesh Brivis Icecap Please note that to maintain your warranty the above servicing needs to be conducted by an authorised person trained in the service of Brivis Coolers Please contact our Brivis Service Department for an authorised Brivis Service Technician Note Service maintenance is not covered under warranty and is a chargeable service All coolers must have safe and reasonable access and be installed in compliance with the installation instructions supplied with the unit Some installations may require two service personnel to attend in accordance with Health amp Safety requirements BEFORE YOU CALL FOR SERVICE OR ASSISTANCE Service calls can often be avoided If you feel your cooler is not operating properly please check these possible causes first Troubleshooting Check the water supply to the unit is turned ON Ensure the pump is operating and visually check the pads for even water distribution Check that the number of doors and windows open is sufficient within the targeted cooling area Too many or not enough doors and windows opened in the targeted area could result in inadequate ventilation This could result in poor cooling performance Check that the fan operates and air is coming out from the duct outlet Check that the filter pads are not damaged and or the material
12. d If it is a humid day operate the system in FAN ONLY mode There is no air coming out of some of the vents It is highly probable that this is an installation issue Please contact your installer in the first instance What does duct cleaning entail Like any other part of your home dirt dust and other foreign particles can accumulate and breed in the ductwork and on system diffusers Remove dust from your cooling system Kill any potential dust mites living amp breeding throughout your cooling system Remove odours from your cooling system Helps improve indoor air quality Allergy sufferers may benefit from clean ducts Clean the Cooler fan and assembly Clean the Supply air diffusers run heating through the same ductwork as my evaporative cooler No the differing technology between ducted heating and evaporative cooling doesn t allow the units to share the same ductwork Also evaporative cooling requires larger ductwork for airflow How cool is cool The degree of cooling available from any type of air conditioning is dependent on the outside weather conditions Your Evaporative Cooler works best on hot dry days After all that s when you require the most relief Should the unit have its own circuit in the meter box Yes we recommend the power socket is wired back to the meter box on a dedicated power circuit Should water be coming out of my evaporative cooler during operation Brivis Iceberg wil
13. d the pump in either Auto or Manual mode the cooler will start a Pre Wet stage to ensure the pads are thoroughly wet before the fan starts This contributes to the effective operation and performance of the cooler The Pre Wet time will vary depending on how long the cooler has been OFF and whether it needs to fill the tank prior to operation Operating Modes The cooler has several operating modes which are as follows 1 AUTO COOL 2 MANUAL 3 FAN ONLY Push the MODE key to cycle through the cooler s operating modes Note The wall control will remember previously established settings in Auto and Manual Modes 1 AUTO COOL Mode In AUTO COOL mode the Programmable Wall Control automatically operates the cooler fan speed and pump to maintain the selected comfort level The cooler may even turn OFF if the conditions meet the comfort level setting Begin by pressing the Power key to turn the Cooler on If AUTO COOL is displayed the system is set for Automatic operation otherwise e Press the mode key to cycle through the Cooler s operating modes until the AUTO COOL is displayed e Push the A and keys to select the comfort level you require The longer the column the cooler the setting the shorter the column the warmer the setting Benefits of using the Brivis Iceberg in AUTO COOL mode in preference to MANUAL mode Power and water consumption varies i
14. ents Certiticate s of Occupancy means certificate s issued by the local council which certifies that a home can be occupied Installation Site means the site at which the Product is originally installed Normal Business Hours means 8 30am to 5 00pm week days excluding public holidays Operating Instructions means the user manual or other documentation which provides detailed instructions on the proper operation and maintenance of the Product Other Applications means any Product used for non Residential and Light Commercial Applications Other Applications may include but are not limited to factory IT Server room telephone exchange processing area e g bakery kitchen warehouse swimming pool agricultural facilities such as a nursery and any Product which has been installed for whatever purpose as a retrofit component to an existing system Purchaser means the end user of the Product the person named as owner in the Warranty certificate the holder of the Proof of Purchase or the holder of a property transfer document where the Product is included as part of the chattels Product means the equipment purchased by the Purchaser and described in Section 2 of this document Proof of Purchase means a Tax Invoice or Receipt in respect of the Product In the case of new constructions a Certificate of Occupancy or a Certificate of Compliance that details the date of installation or commissioning wi
15. esents the only Warranty given by Brivis and no other person or organisation is authorised by Brivis to offer any alternative Exclusions This Warranty does NOT cover a damage problems or failure resulting from improper operation and or inadequate maintenance by the Purchaser refer Purchaser s Responsibilities section below b damage problems or failure resulting from improper or faulty installation The Product must be installed by a Qualified Installer in accordance with applicable regulations Where applicable Certificate s of Compliance must be obtained by the purchaser from a Qualified Installer and present it to the Authorised Service Representative c damage problems or failure caused by factors external to the Product including but not limited to faulty or poor external electrical wiring incorrect or faulty power supply voltage fluctuations over voltage transients or electromagnetic interference inadequate or faulty gas drainage services or water services including water pressure and non potable water d damage problems or failure caused by acts of God fire wind lightning flood storm vandalism earthquake war civil insurrection misuse abuse negligence accident pests animals pets vermin insects spiders or entry of foreign objects or matter into the Product such as dirt debris soot or moisture e damage problems or failure caused by weather including but not limited to hail salt or other corrosive
16. hasn t deteriorated If external weather conditions are excessively humid the cooler may not perform at its optimal cooling level Check that the Module Inlet mesh and all air intakes e g Brivis lcecap mesh are clean and free from obstruction If the fan will not start Check if the power is ON Check if the Wall Control is turned ON and set the comfort level that requires the Cooler fan to operate Check that the system is not in Time Delay or Start Up mode Check the fuse in the meter box Note The usual time delay can be up to 4 Minutes on start up Problem Action The unit will not turn on Check the circuit breaker has not been tripped if so reset it Reset the Cooler at the power supply The unit is blowing warm air Check the water supply tap is turned on at the unit Check the system is not in FAN ONLY mode The wall control display Check there is power to the power point with another appliance e g hair is blank dryer Check the circuit breaker has not been tripped if so reset it The unit is not cooling very well Check the water supply tap is turned on at the Cooler Check sufficient doors and or windows have been opened Refer to Exhaust section Check air intakes are clean and free of any obstruction There is no air coming It is highly probable that this is an installation issue Please contact your out of some vents installer in the first instance There is moisture on my tiles Check the vents
17. he amount of cooling available from any type of cooling system is dependent on the outside weather conditions Your evaporative cooler works best on hot dry days It is essential to provide the required amount of ventilation for your evaporative cooling system to function properly by opening windows doors whenever the cooler is operating Air is drawn in through the filter pads resulting in 100 fresh cool air entering the home The movement of this cooled air through your home will draw the heat out of the house so be sure that doors or windows are open to expel this heat to outside Whenever possible start the cooler early to prevent the build up of heat within the house and on sultry or humid days your cooler may work better with the fan ONLY running and the pump turned OFF Stale air cigarette smoke and fumes can be quickly cleared and replaced with fresh air by turning the fan to manual mode Make sure enough window and or door area is open for the unit to work correctly Table 1 gives a guide to the amount of open area required in m2 and also gives suggestions on how to provide this Safety Warnings Do not place any articles on or against this appliance Dot use or store flammable materials near this appliance Do not spray aerosols in the vicinity of this appliance while it is in operation e Do not modify this appliance The air smells a little different Why New cooling pads can give off a mild odour while they are settling
18. ian States it is mandatory that your cooler installation is issued with a certificate of compliance to guarantee the installation workmanship Please check with your installer or the local plumbing authority or association The Brivis cooler is covered by the product warranty as outlined in this manual Brivis products are renowned for providing years of trouble free performance However that doesn t mean that they will operate at their peak for all of that time without some attention To be at their most efficient they like most things need a little care So to ensure that every Brivis unit is always in perfect condition we have established the Brivis Care Program for our valued customers The Brivis Care Program provides you with a maintenance service This service includes cleaning the unit and ensuring that the system is operating at maximum efficiency Not only does this guarantee peak performance it also allows any minor problems to be detected early This ensures that the system will always be ready when you need it Privacy Notification Brivis Climate Systems Pty Ltd is the registered owner of the Brivis brand Brivis will collect personal information from you when you complete your warranty and maintenance registration form This personal information is collected under the guidance of the Privacy Information Protection Act 1998 The purpose of collecting this information is to e Process your request for us to provide service ac
19. l complete a flush service once every eight hours of operation maximum This means you may hear and or see the unit discharge water from the primary drain pipe There is water coming out of the secondary drain There is a secondary drain 40 mm which is terminated to provide you with clear visibility of water discharging If you see water discharging from this drain call Brivis I have turned the unit off and it continues to run for a short period This is normal operation the water is turned off and a dry cycle is commenced on shut down What will happen to the unit if it loses power during operation The unit will stop working and when power returns water will discharge and the wall control will remain in the OFF state 12 1 Terms of Warranty Australia and New Zealand Brivis Climate Systems Pty Ltd ABN 64 096 079 088 AU24752 61 Malcolm Rd Braeside VIC 3195 Definitions The terms listed below shall have the following meanings 1 10 11 2 PR Authorised Service Representative means an independent service contractor authorised by Brivis or Brivis service personnel Brivis means Brivis Climate Systems Pty Ltd ABN 64 096 079 088 and any related company Certificate s of Compliance means certificate s issued by licensed personnel including plumbers refrigeration mechanics electricians or other relevant trades people to certify that any prescribed works comply with applicable regulatory requirem
20. ll suffice Qualified Installer means the qualified installation contractor who is responsible for performing the installation work in the manner prescribed by local and statutory regulations including compliance with any relevant Australian Standards and to Brivis specification Residential amp Light Commercial Applications means any Product for use in both residential and light commercial applications For example homes offices hotels apartments nursing homes hospitals health care premises shopping centres retail stores where the Product is solely used for purpose of human comfort understandard operating conditions Terms of Warranty Subject to the Terms of Warranty set out in this document effective from the date of purchase by the Purchaser the Product is warranted to be free from defects in materials and factory workmanship for the period set out in the table below PRODUCT GROUP PARTS LABOUR Evaporative Coolers amp Ducted Gas Heaters excluding Compact Classic Series S YEARS Residential amp Light Ducted Gas Heaters Compact Classic Series 3 YEARS 3 YEARS Commercial Refrigerated Airconditioning Products 5 YEARS 5 YEARS Ducted Gas Heaters Heat Exchangers amp Burners Evaporative Coolers Structural components only TO SENS WA Other Applications All Product Groups 1 YEAR 1 YEAR Aftermarket Spare Parts 1 YEAR N A Must be read in conjunction
21. n relation to the chosen comfort level This comfort level cannot be as easily maintained in MANUAL mode In AUTO COOL mode the unit operates only when it is required Enables a set comfort level to be maintained automatically as the outdoor indoor temperature conditions change Allows you to pre set the cooler to turn ON early and not let the house build up heat The outlet airflow noise is kept to a minimum as the fan speed is only as fast as required to maintain the set comfort level This slower speed also results in more efficient saturation of the cooler filter pads and a cooler outlet air temperature 2 MANUAL Mode MANUAL mode operation allows you to manually control fan speed the pump is always on Begin by pressing the Power D key to turn the Cooler on If MANUAL is displayed the system is set for manual operation otherwise e Push the MODE key to cycle through the cooler s operating modes e Push A and keys to select the fan speed level you require The larger the column the faster the fan speed the shorter the column the slower the fan speed 3 FAN ONLY Mode FAN ONLY mode operation allows you to manually operate fan speed only e Push the and keys to raise and lower the cooler s fan speed Timer Function This wall control has a timer function that can delay the operation of the system turning ON OFF If the cooler is operating you can pre set the timer for the cooler to
22. of these documents may be used in any way or form without prior written consent from Brivis Climate Systems Pty Ltd Part Number B024630 February 2015 Brivis Climate Systems Pty Ltd ABN 64 096 079 088 Brivis Pty Ltd 2015 All rights reserved AU 24752 Issue B
23. onal corrosion protection is applied to the Product if it is installed in a corrosive environment for example close to the sea 8 Statutory Rights 8 1 8 2 8 3 The benefits given by this Warranty are in addition to other rights and remedies of the consumer under a law in relation to the goods or services to which the Warranty relates Australian purchasers have their benefit of statutory rights and nothing in these terms of Warranty has the effect of excluding restricting or modifying those rights Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure For New Zealand purchasers nothing in these terms of Warranty is intended to limit the rights you may have under the Consumer Guarantees Act 1993 The Consumer Guarantees Act 1993 does not apply if the Product is acquired for the purpose of a business as defined in the Act the problem is not covered by these Terms of Warranty there is nothing wrong with the product e g instructing Purchaser on the operation of the Product and or controls or if the Purchaser is unable to provide Proof of Purchase validating that the Product is within the Warranty
24. period We recommend that you read the operating or send to Brivis Warranty Claims 61 Malcolm Road Braeside VIC 3195 For New Zealand Warranty Service call 0800 WARMAIR 0800 9276 247 Brivis only The PURCHASER WILL BE For Australian Warranty Claims call 1300 Brivis 1300 274847 CHARGED for work done or a service call s if instructions and in particular the troubleshooting section of the Operating Instructions before you make a Warranty service call Proof of Purchase must be presented Effective Ist October 2013 15 Notes 16 Notes 17 For all your Sales and Service enquiries call us on 1300 BRIVIS 1300 274 847 www brivis com au Brivis Australia Brivis New Zealand Brivis South Africa 61 Malcolm Road Distributor Warm Air Ltd Distributor Lorenz and Associates Braeside Victoria 3195 69 Marsden Street Northlands Deco Park Australia Lower Hutt 5010 New Zealand Cnr Witkoppen and Newmarket Roads 1300 BRIVIS 1300 274 847 PO Box 38523 North Riding Johannesburg South Africa 2194 Fax 61 03 9264 9400 Wellington Mail Centre 0861 BRIVIS 0861 274 847 www brivis com au Wellington 5043 New Zealand Ph 27 011 704 6112 email sales brivis com au 0800 WARMAIR 0800 9276 247 Fax 27 011 704 0022 Ph 64 04 920 1670 www brivis co za Fax 64 04 920 1681 email info brivis co za www warmair co nz email sales warmair co nz Copyright Brivis Climate Systems Pty Ltd All rights reserved No part
25. s towards points of ventilation cooling as it moves through the rooms Open windows Operating your evaporative cooler Start up When the cooling is first turned ON there will normally be a delay before the cool air is delivered from the duct outlets The delay time allows water to fill the Cooler s tank and or Pre wet the filter pads The entire process can take up to 4 minutes before cool air is expected from the duct outlets Shut down There is a delay of up to 6 minutes after the system is turned off during which time the Brivis Iceberg performs a self clean and dry function All water will be drained from the unit 45 minutes after the unit has been turned off On humid days On days of high humidity your evaporative cooler works best with the fan on high and perhaps the pump switch turned off If moisture is building up on tiled or hard surface areas ensure that airflow from the outlets is directed across the ceiling rather than down towards the floor Also ensure that you have enough windows and or doors open Ceiling Exhaust Vents Security Relief Vents Ceiling exhaust vents security relief vents are not recommended as recirculating air will impair performance of the cooler Operating your Wall Control The Brivis Iceberg Programmable Wall Controller gives the choice of Automatic or Manual modes with the option of a time ON or OFF delay Automatic Pre Wet When the cooler is turned on with both the fan an
26. sts which are within the terms of the authorisation If the Purchaser pays for the relevant freight charges in transit insurance expenses or travelling costs without written authorisation from Brivis Brivis will not reimburse the Purchaser for such costs The Purchaser must pay all costs and expenses in respect of a making the Product accessible for service For example restricted access or working at heights or the labour cost for an additional person due to OHS requirements b providing a sate working environment for installation service maintenance or repair of the product c any surcharge applicable in respect of supplying replacement parts outside Normal Business Hours and d any other costs and expenses in relation to claiming the Warranty that is not covered by clause 6 2 7 Purchaser s Responsibilities 7 1 The Purchaser must operate and maintain the Product in accordance with the Operating Instructions and service maintenance schedule including conducting an appropriate number of services to the unit during the Warranty period based on usage and the usage environment including but not limited to a regularly cleaning the air filter s and replacing them where necessary b replacing expired batteries or other consumables as required c ensuring that the condensate drain is kept clean and clear of obstructions d ensuring that outdoor units have unrestricted airflow and adequate clearances ensuring that additi
27. te the unit Ensure the pump is operating and visually check the pads for even water distribution Ensure the water inlet is operating correctly Ensure the water system is operating to the minimum and maximum water levels Check that the water supply pressure is sufficient to fill the tank within the allotted time Check the fan operates and varies speed between the minimum and maximum setting on the Wall Control Check and lubricate all moving parts Clean Module Inlet Mesh and Brivis lcecap Mesh if installed Please note that to maintain your warranty the above servicing needs to be conducted by an authorised person trained in the service of Brivis Iceberg Coolers Q A gt gt gt gt Why does the unit dump water periodically during operation Brivis Iceberg coolers use the Running Refresh method for tank water quality control This Running Refresh ensures that the salt or sediments accumulating in the cooler do not exceed an acceptable level by periodically flushing the tank while the cooler is operating The air smells a little different Why New Cooling pads can give off a mild odour while they are settling in This is quite normal it will dissipate quickly as the new pad is constantly flushed during use It may also be indicating that the unit requires a service How much water does my evaporative cooler use The amount of water an evaporative cooler uses is dependant on the evapor
28. tivities for you e Register your purchase of equipment for warranty e Register your request for a survey quotation for Heating Ventilation Air Conditioning goods and services The intended recipients of the information are Employees of Brivis Federal and State Governments who may require the information for administration purposes While the supply of the information by you is voluntary if you cannot provide or do not wish to provide the information sought Brivis may not be able to provide the services you request If you have already provided information but have changed your mind and do not want the information used you may make application for access or amendment for that information not to be used You have a right of access to and correction of the information concerning yourself in accordance with the relevant procedures under the Act Enquiries concerning this matter can be addressed to the Business Practices Officer of Brivis who can be contacted on 1300 BRIVIS Before operating your Brivis Evaporative Cooler This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance How does your evaporative cooling work T
Download Pdf Manuals
Related Search