Bluetooth GPS Receiver BT-399
Contents
1. Setup GPS INFO About a Scan Com Port dose onlof je a opa reception TG es m Re start Cold start Power Save Power Save Modus NMEA data display Switching between this window and our window l Date 4 M 2003 03 26 Date STA UTC 07 40 44 Time v Drectiaru 91 63 Direction Speed See below Lat M 24759 8868 Lon E 121729 2218 Longitude 8 Latitude Example fa 9 Satellites found 10 24 04 02 18 07 29 13 01 05 30 08 5 thereof are active Setup GPS INFO About ET HDOP Horizontal Dilution Of Position Should you see the NMEA protocol in the GPS Info but you cannot find a receiver in your application software then it is not a mistake of the receiver but of the setting in the software The support of the software producer may help you Risk of explosion when exposed to fire Don t expose the receiver to permanent temperature above 60 C 140 F 7 Possible Sources of Malfunction and Troubleshooting 7 1 The device cannot be switched on Check if the battery is fully charged Plug the charger to BT 399 and into the socket If the LED lights up in red Wait for 10min unplug the receiver and switch it on If you can see some function as the green LED flashes the battery was not fully charged Switch on the BT 399 again and charge it completely until the red LED turns off 7 2 The battery was charged and the BT 399 can still not be s2. The product was exposed to rain or liquidity The product fell down and is damaged There are visible signs of overheating The product does not work properly despite of correct operation Avoid using the device after high variation in temperature If you expose the device to high variation in temperature or humudity there may be condensation in the device In order to avoid damages wait until the humidity is evaporated before using it NOTE If you bring the device from a cold into a warm or from a warm into a cold environment let the device take over the temperature before switching it on 3 2 Operation 2 1 Plug the Mini USB cable with the bigger connector into the charger Connect the charger to a wall socket 2 2 The Mini USB connector has to be plugged into the Mini USB female port 4 of BT 399 2 3 The red LED lights Charge the batter completely Unplug the Mini USB cable after the red LED turned off 3 LED Indication Blinking no Bluetooth pairing Blazing Bluetooth pairing established no LED indication after 1 minute Blinking no satellite fix Blazing more than three satellite fixes available Blinking if battery status is not enough Blazing when recharge the battery 4 Operating surrounding The BT 399 can be used under all common OS Systems as Bluetooth GPS receiver Drivers are not required 5 Application 5 1 For a Notebook with Bluetooth 1 Turn the BT 399 on 2 Pl
3. NAVILOCK osna le FE CE 0500 ma Bluetooth GPS Receiver BT 399 BT 399 User Manual 60311 a NAVILOCK e13 FECE 0550 027 49 1 Introduction The BT 399 is a Bluetooth GPS receiver with internal antenna and Sirf3 20 channel GPS chipset The Bluetooth interface enables a connection to a PDA SmartPhone mobile phone or notebook Due to its extremely compact design it acts as ideal companion on every tour 1 1 Package content 1x Navilock BT 399 1x Power supply 1x Car Charger 1x USB Mini cable 1x 3 7 Volt 850mA rechargeable battery internal 1x User manual 1x 8cm CD ROM 1x Navilock key strap Make sure that the product package contains all items before operation If any item is missing or damaged then please contact your dealer immediately 1 20 2 3e 1 2 Connectors Operation elements 4 1 Bluetooth LED 5 2 Satfix LED 3 Battery status indication LED 4 Mini USB charger connector 5 GPS Patchantenna under the case 6 Key strap whole fe 4 f e 7 ON OFF switch 2 Important health and security information If you use this product you should take precautions to avoid damages and legal consequences Follow precisely all security and handling advice and keep it carefully Pay attention to all warning notices in the manual and on the device To avoid injury electric shock fire and damages on the device please pay att
4. TE Rate Dynamic requirements Acceleration Altidue Speed Performance Operation time Rechargeable battery Connector Bluetooth Operation temperature Weight Dimensions SiRF star III GSC3FLP 20 channel 158dBm L1 1575 42MHz 1 023MHz Chip Rate 5m CEP S A off 1 micro sec synchronized to GPS time 0 1m sec 95 SA off WGS 84 NMEA 0183 V3 01 GGA 1sec GSA 1sec GSV 5sec RMC 1sec 3 5s average with ephemeris and almanac 38s average with almanac but without ephemeris 42s average either almanac nor ephemeris 1s average recovery time after interruption 1Hz less than 4g 18000 meter 60000 feet maximum 515 meter sec 1000 knots maximum maximum 10 hours 3 7 Volt 700mA Li ION battery USB CSR BC4 Bluetooth Chipset V1 1 Class 2 Serial Port 10 C 60 C 30g with battery 40 0 mm x 70 0 mm x 9 2 mm 9 9 Certificate CE 08214018 AA 00 R amp TTE 08214018 AA 00 CE0506 E Mark e13 02749 10 Warranty period Your GPS receiver will be repaired free of charge during the legal warranty period provided the damage was not caused by external impact moisture fall or improper use 11 Support If you have further questions please contact our customer support support navilock de www navilock com or phone 49 30 84716503 You can contact our service hotline during the following times Mon Fri 9 00am 16 30 pm A connection fee applies according to fee schedu
5. ates the conformity with the following European standards in brackets you will see the equivalent international standards EN 300 328 V1 7 1 2006 10 EN 300 440 1 V1 3 1 2001 9 EN 300 440 2 V1 1 2 2004 07 EN 300 328 V1 7 1 2006 10 EN 301 489 1 V1 6 1 2005 09 EN 301 489 17 V1 2 1 2002 08 EN 301 489 19 V1 2 1 2002 11 EN 50371 2002 3 EN 60950 1 2001 A11 2004 Z CE 0560 FE 027 49 NZ Compliant 11 WEEE notice The WEEE Waste Electrical and Electronic Eguipment directive which became effective as European law on February 13th 2003 resulted in an all out change in the disposal of disused electro devices The primarily purpose of this directive is the avoidance of electrical waste WEEE and at the same time the support of recycling and other forms of recycling in order to reduce waste The WEEE logo on the device and the package indicates that the device should not be disposed in the normal household garbage You are responsible for taking the disused electrical and electronical devices to a respective collecting point A separated collection and reasonable recycling of your electrical waste helps handling the natural resources more economical Furthermore recycling of electrical waste is a contribution to keep the environment and thus also the health of men Further information about disposal of electrical and electronical waste recycling and the collection points are available in local organizations waste
6. ease refer to the Notebooks user s guide for instructions to activate Bluetooth for connection to the BT 399 As these are always a little bit different Usually you proceed as follows 3 Enter the Bluetooth Manager and search for devices in the Bluetooth surroundings 4 As soon as the Bluetooth GPS receiver is found connect it to your PC Notebook 5 Depending on the Bluetooth Software you have to choose the Com port before pairing the device 6 Choose the Com Port between Com3 to Com10 since some old software solutions often do not see a Com Port over 10 7 If your Bluetooth Software chooses the Com Port automatically please follow the instructions step by step to finish 8 Make sure which Com port was chosen by showing the features of the linked Bluetooth device 9 Some Bluetooth Applications or programs require an access code for linking the device In case this request appears the access code is 0000 10 Exit the Bluetooth Manager 11 Launch the suitable software for mapping navigation and select the correct COM Port and set the baud rate between 4800 and 115200 4 5 2 For PDA SmartPhone with built in Bluetooth l 2 Turn the BT 399 on Go to Bluetooth settings and search for devices in the Bluetooth environment Choose the GPS receiver as to be paired device Some Bluetooth Applications or programs require an access code for linking the device In case this request appears the access code is 0000 E
7. ention to the following notices Electrical Security This product is intended for operation with power of rechargeable battery or the stated power supply Any other application can be dangerous and lead to loss of any warranty claim for this product Please use only the original accessory and never charge the re chargeable battery with a charger from other producers Careful handling of the rechargeable battery There is danger of fire and burning when the re chargeable battery wont be used properly Do not disassemble destroy perforate short out or throw it into water or fire or expose it to temperature higher than 60 C 140 F NOTE RECYCLE OR DISPOSE USED BATTERY ACCORDING TO THE LOCAL INSTRUCTION OR THE ENCLOSED INSTRUCTIONS FOR THIS PRODUCT SECURITY ADVICE REGARDING DIRECT SUNLIGHT Make sure the device is not exposed to over humidity and extreme temperature Don t let the device the battery or the re chargeable battery for too long in a vehicle or other places where the temperature can rise up to 60 C 140 F e g on the dashboard window sill or behind a glas panel which is exposed to high UV Light or the sun In this case the device or the vehicle can be damaged and the battery superheated Damages which require a repairing Disconnect in the following cases the device from the grid and contact an authorized repairing specialist or the dealer Liquidity or any item came into the product or an object got into the device
8. le of your local telephone provider You can find current product information on our homepage www navilock com Please send your repairing transmittals franked to this address Navilock Repair Center Beeskowdamm 13 15 D 14167 Berlin Zehlendorf Please include a proof of purchase and a detailed error description doesn t work or defec is not detailed Please pay attention to the occurrence of the error Transmittals which are not franked cannot be accepted due to logistic reasons 12 Final clause Information and data contained in this manual are subject to change without notice in advance Errors and misprints excepted 13 Copyright No part of this users manual may be reproduced or transmitted for any purpose regardless in which way or by which means electronically or mechanically without explicit written approval of Navilock 10 Navilock is a registered trademark and cannot be used without the written permission of its trademark owner In no case shall it be modified or amended 14 Third party trademarks Marks trademarks products names and logos of third parties that are shown in this documentation are marks or trademarks of their respective owners Declaration of conformity Products with a CE symbol fulfill the R amp TTE directives 99 5 EC the EMC directives 89 336 EEC and the low voltage directives 73 23 EEC which were released by the EU comission The compliance with these directives implic
9. lication has access to the COM Port and data starts flowing the LED will be turn off after roughly one minute 6 Functiontest with GPS Info 1 Install the GPS Info software on your device Choose the respective version for your system On the CD you can find versions for Windows 98SE Me 5 W2K XP Windows Vista and WM5 also usable for WM6 GPS Info is only a Testprogram and cannot be used for navigation or orientation After testing it has to be closed Please make sure on a Pocket PC that it is really closed and not still active in the background It blocks the Com Port and doesn t give access to a navigation or routing software on The PC version differs basicly only in its appearance from the Pocket PC 2 the Com Port 3 version The amount of function remains the same 4 PC Version GPS Information About COM Port COM6 Baud Rate x Scan Com Port Start GPS Cold Start COM Port Settings choose Baud rate Activates and de activates the GPS test additional settings Setup GPSINFO lt NMEA Protocol window Switching between this window and the visual display of NMEA dataset Baud Rate 38400 Baud rate selection GPGSA A 3 28 01 20 04 08 07 11 2 lt GPRMC 039521 227 4 2459 9856 N GPGG4 035522 227 2459 8856 N 12 GPGSA A 3 28 01 20 04 08 07 11 24 GPRMC 035522 227 A 2459 8856 M
10. management enterprises in specialized trade and the producer of the device Compliance with RoHS This product complies with the directive 2002 95 EC of the European parliament and the council from January 27th 2003 concerning the restricted use of dangerous substances in electrical and electronical devices ROHS as well as its modification e and E mark This product complies to the EMV guidelines 2006 28 EG and ECE regulation no 10 as electronic device or sub assembly Version 06 2008 12
11. vilock Repair Center as well can identify the damage and give a cost estimate Please send the device franked and state as error description KVA falsche Stromversorgung The Navilock Repair Center aims to be as fair as possible So we kindly ask you to give a true error description The error analysis helps to find out if there was a water damage interference by a third party a fall overvoltage or wrong handling Often malfunctions are caused by minor errors It is not always necessary to immediately replace a product because this will not correct a malfunction that is not caused by the GPS hardware Before contacting your dealer please contact Navilock support This will provide you with help in a fast and easy manner and help avoid unnecessary replacement In such cases describe the malfunction as accurately as possible in writing add the details for your device and the software you are using as well as operating surrounding Operating system Servicepack version CPU size and type memorysize type of HDD and interface etc and send an email to support navilock de sas A member of the support team will take care of your problem and work on a solution We hope you enjoy your Navilock product 8 Technical data Chipset type Channels Sensibility Freguency C A Code Accuracy Horizontal position Time Speed Date Protocol Acquisition rate Hot start Warm start Cold start Reacquisition UP DA
12. witched on Please contact the Navilock Support 7 3 Your PC does not support the Autostart function and does not start the CD ROM automatically Please read http msdn2 microsoft com en us library Aa969329 aspx 7 4 Your BT 399 cant find a FIX or takes too much time for it The GPS reception is a reception requiring a free view to the sky But today s high sensitive chipsets enable a reception even without enough view to 7 7 5 7 6 7 1 the sky That is only possible if there are enough good signals of satellites available Even with a bright blue sky the signals of the satellites can be so distorted because of electro magnetic disturbance so that it cannot be used as Signals for the receiver This is not due to the receiver but due to the physical basic law of the electro magnetic radiation Switch off the BT 399 and try later again Try to find a location which is not near to a house wall There can be also reflections which can disturb the reception If you use the BT 399 for the first time the first Satfix can take up to 30min The same can happen when you use the receiver on another continent The BT 399 got wet Do not connect the receiver to the charger Thus it will be definitely and not reparable destroyed Please send the receiver with statement Water damage to our support The Support will open and dry it and test the function again You used the BT 399 with a wrong charger In this case only the Na
13. xit the Bluetooth Manager Launch the suitable software for mapping navigation and select the correct COM Port and set the baud rate between 4800 and 115200 Perform a softreset on your device if you have any errors or configurationproblems It can be performed before or after pairing in order to exclude blocked ComPorts or applications If your BT 399 interlinked correctly and your Mapping and Navigationssoftware does not receive any data please perform the following steps Go to Start gt Settings gt Connection gt Transfer Data reception Check if there is a tick for automatic receiving If yes please take out the tick leave this window with OK and the following windows with X until you get back to the Desktop After that run a softreset Go to the Bluetooth Manager delete the interlinked GPS mouse and set a new connection For devices based on Windows Mobile please note that an output connection for the GPS receiver is already placed If this is not the case please provide a new output connection for BT 399 in the Bluetooth manager in the tab Com connections All free Com Ports are being offered When interlinking the device a question about a safe connection may occur Take out the tick for safe connection 5 3 General note for pairing As soon as the receiver is connected to the PDA or SmartPhone the blue LED will light up and hence stops blinking Once a navigation software application or a test software app
Download Pdf Manuals
Related Search