MII User Manual
Contents
1. Model No Capacity Division MII 600 600 g 21 oz 0 1 g 0 005 oz MIl 1200 1200 g 2lb 80z 0 2g 0 01 oz MII 3000 3000 g 6 Ib 0 5 g 0 02 oz MII 6000 6000 g 13 Ib 1 g 0 05 oz Power source 1 x 9V battery or power adapter Max zero range 100 of rated capacity subtractive Weight Units g Ib oz Operation Environment 0 to 40 C 32 to 104 F Non condensed R H 85 3 KEYBOARD LAYOUT AND DESCRIPTION ON ZERO KEY Press this key to turn scale on or to return the scale to zero TARE KEY Press this key to tare off the weight of a container or set a negative weight displayed to zero when unloaded MODE KEY Press this key to switch between metric and avoirdupois weight units OFF KEY Press this key to turn off the unit AVOIRDUPOIS UNITS INDICATOR The Ib oz indicator will appear when the avoirdupois weight unit is being employed ZERO INDICATOR This 0 indicator will appear when the scale is at true zero LO BAT INDICATOR This indicator will appear when the battery voltage is too low Replace battery or immediately apply the power adapter provided METRIC INDICATOR This g indicator will appear when the metric weight is displayed 4 1 INITIAL SETUP Internal Settings The scale is equipped with Auto Power Off Function and metric and avoirdupois weight units a Press and hold TARE then press ON ZERO b FUN 1 is displayed c Press TARE to select the desired2. container When a container is used follow the below steps to tare off its weight and get a net weight result a Remove all loads from the platter b The ZERO INDICATOR will appear c Place the container on the platter d Press TARE After ZERO is pressed the scale will display TARE and then a zero weight value will be displayed The ZERO INDICATOR will not appear even though a zero weight is displayed The net weight is displayed Clear the Tare Function a Remove all loads from the platter b The scale will display a negative value which is the weight of the container The ZERO INDICATOR will appear c Press ZERO d After ZERO is pressed a zero weight will be displayed while the ZERO INDICATOR remains LO BAT Indicator When the LO BAT INDICATOR appears it means that the battery is faded out Replace the battery with a new one or apply the power adapter immediately CATION When the power adapter is being used take the battery out from the battery pack Failure to do so may cause battery leak explosion or damage to the scale 6 TROUBLE SHOOTING Symptom Check Action Check Action Symptom Check Action Check Action Scale cannot be turned on Is the scale powered or battery low Refer to 4 1 Select AUTO POWER OFF function status and weight unit to disable the AUTO POWER OFF function Is the power adapter inserted properly into both the electricity outlet and the DC inlet of th
3. function FUN 4 Press MODE to move between 4off the scale will turn off in 4 minutes 10off the scale will turn off in 10 minutes 200ff etc Ooff the scale will not turn off When you have selected the required setting press ON ZERO to return to weighing Note Under the Auto Power Off function mode the scale will turn off automatically when left idle 5 1 5 2 5 3 INSTRUCTIONS FOR USE Before using make sure that a The plastic platter is placed correctly on top of the load receptor and the stainless steel platter cover is placed on top b The scale is placed on a level and strong surface c The scale is turned on d The ZERO Indicator is on If not press ON ZERO to set the display to zero Weighing a Always place an object onto the platter gently Excessive force applied to the platter may cause damage to the sensor inside the scale b The weight of the object will be displayed automatically c It is a good practice to remove all loads from the platter after weighing It will prolong the life of the scale Selecting the Weighing Unit Press MODE to shift between g and Ib oz Refer to 4 1 1 for internal setting procedures The weight unit used before power off will be employed when the scale is turned on again Refer to 5 2 for weighing procedures Weight displayed is the net weight of the load Refer to SPECIFICATIONS for maximum tare range 5 5 5 6 5 7 Tare off the weight of a
4. Mil SERIES DIGITAL WEIGHING SCALE OPERATION MANUAL PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPTING TO OPERATE THE SCALE February 2006 Rev 2 Specifications subject to change without prior notice CONTENTS 1 INSTALLATION 2 SPECIFICATIONS 3 KEYBOARD LAYOUT AND DESCRIPTION 4 INITIAL SETUP 5 INSTRUCTIONS FOR USE 6 TROUBLE SHOOTING 7 DAILY CARE AND MAINTENANCE 1 INSTALLATION 1 1 Check to make sure that the following items are included This operation manual Scale x 1 Stainless steel platter cover x 1 Power adapter x 1 Contact your dealer if any items are missing 1 2 Insert the legs of the plastic platter carefully into the holes on top of the scale then place the stainless steel platter on top 1 3 Power the Scale a Insert one 9V battery into the battery pack underneath the scale or b Connect the power adapter Before plugging the power adapter into electricity outlet check to make sure that the input voltage of the power adapter matches the output voltage of the outlet If not do not plug in the adapter Contact your dealer immediately CAUTION When the power adapter is being used take the battery out from the battery pack Failure to do so may cause battery leak explosion or damage to the scale Do not use any rechargeable battery The scale does not recharge any battery 1 4 Retain the packing materials for future transportation use 2 SPECIFICATIONS
5. e scale Secure both ends of the power adapter and try again Scale turned off automatically Is the AUTO POWER OFF function employed Refer to 4 1 Select AUTO POWER OFF function status and weight unit to disable the AUTO POWER OFF function Is the LO BAT INDICATOR on Replace the battery with a new one or apply the power adapter immediately CATION When the power adapter is being used take the battery out from the battery pack Failure to do so may cause battery leak explosion or damage to the scale Symptom Check Action Check Action Check Action Check Action Weighing result is not accurate Is the scale placed in a level condition Relocate the scale to obtain a level condition Is the scale affected by air flow vibration of RFI Place the scale away from all disturbances Is the scale calibrated correctly Contact your dealer Is the correct weight unit employed Refer to 4 1 and 5 3 for weight unit setting and usage 7 1 7 2 7 3 DAILY CARE AND MAINTENANCE Do not splash water on the scale Clean the scale with a soft damp cloth If necessary apply a mild detergent Do not use any harsh abrasive material acetone volatile solvent thinner or alcohol for cleaning Verify the accuracy of the scale periodically Re calibrate the scale if necessary NOTE In some countries calibration is restricted to be done by an authorized qualified agent only Contact your dealer for more in
6. formation 7 4 7 5 7 6 Store the scale in a dry and clean place Before storage for a long period of time remove all batteries from the battery pack Do not open the scale There are no serviceable parts inside Contact your dealer for after service
Download Pdf Manuals
Related Search