QualColor™ Touch Commander
Contents
1. EZ Giulio Fa Lighting Copyright 2010 Giulio Lighting All rights reserved QualColor is a trademark of Giulio Lighting Windows is a registered trademark of Microsoft in the United States and other countries Macintosh is a trademark of Apple Inc All other brand or product names are trademarks or registered trademarks of their respective owners Contact This document and the functionality of the product may be subject to change without notice Publication 24 00026 012. 1 Connect the QualColor Touch remote to the computer and start the QualColor Touch Commander program Select the Configure QCTouch tab Set the Fixture Address for Active Link 1 is set to Zone 1 and Unit 4 make sure the Active radio button by 1 is selected Load this into the QualColor Touch remote control by pressing the Set QCTouch button Exit the QualColor Touch Commander program and disconnect the remote control from the computer always disconnect the remote control after quitting the program Take the QualColor Touch remote control to the fixture Put the fixture controller into provisioning mode by pressing the Prog button and observing that the Prog indicator is illuminated Put the QualColor Touch remote control into linking mode by pressing the Link Mode button with the unrolled end of a paperclip The red indicator will blink slowly Press the M1 button briefly to re link the remote control to the fixture controller Observe the Prog indicator on the fixture controller is turned off indicating a successful link Press the Link Mode button again on the remote control or wait until the red indicator stops blinking approximately 30 seconds and test operation of the system operating at the new Fixture Address pair See the QualColor Touch remote control User Manual for more information on the linking process 21 QualColor Touch Commander Error Messages No interface device detected The QualColor Touch remote
3. 2 Function Buttons 3 Fixture Addresses When the program is first run the current values in the QualColor Touch remote control are displayed in these three areas A red check mark is displayed next to any item that has been changed The check mark is an indicator that the value does not match the value in the remote control The Set QCTouch button loads any values that have been changed into the remote control The Default button sets all values to the factory default values Radio Interface The Radio Interface section allows the user to select a different radio channel or Network Id to avoid interference with other devices or systems The four radio channels are spread across the frequency spectrum that the LEDlink radio protocol operates in Channel 1 is at the low end of the spectrum Channel 4 is at the high end of the spectrum Channels 2 and 3 are approximately one third and two thirds of the way through the spectrum but adjusted slightly to avoid the most common computer WiFi frequencies The factory default is channel 1 It is recommended to try channel 4 next and then channels 2 and 3 if radio interference is suspected Click the radio button next to the desired radio channel and then click the Set QCTouch button to update the value in the remote control The Network Id is a linking attribute that can be used to separate different LEDlink networks even if they overlap physically The typical use is to avoid interference with a system
4. Edit Help Color Dimmer Dynamic Effects Configure QCTouch Configure Fixture Water Candlelight 6 95 Evening Glow Passion Winter Holiday Mardi Gras Spring Holiday Independence Day Fall Holiday Dynamic Effects Tab The Dynamic Effects tab allows the user to run an automatic program on the computer that will dynamically change the color of a light fixture according to the selected theme The QualColor Touch must be within range of the light fixture Fixture Address The Zone and Unit fields set the fixture address of the light fixture controller The way the Fixture Address is set and used depends on the current mode Single Fixture Mode is used when the QualColor Touch remote control is linked to a single fixture controller or multiple fixture controllers sharing the same address Multiple Fixture Mode allows the QualColor Touch remote control to operate up to ten fixture controllers each with a unique address Single Fixture Mode The Zone and Unit fields may be changed to address any fixture These fields are set initially to match the currently active link in the QualColor Touch Either type a new value in the field or use the up down arrow keys to change the value Multiple Fixture Mode The Zone and Unit fields indicate the base fixture address unit address of the first fixture These fields are set using the preferences properties menu item The QualColor Touch Commander program will control al
5. residing outside of the user s control for example in another apartment or home If fixtures in both locations change whenever either remote control is used then it is appropriate to change the Network Id in one location The factory default Network Id is 0 The Network Id may have any value 0 255 Two LEDlink networks with different Network Ids will not interfere with each other even if they are operating on the same radio channel and have fixtures with the same addresses To eliminate interference between different LEDlink networks change the Network Id value and then click the Set QCTouch button to update the value in the remote control Note that for any changes in the radio channel or Network Id the QualColor Touch will need to be re linked with the fixture controllers it is operating so that these controllers may be updated to use the new link information The linking process is described in the QualColor Touch User Manual Function Buttons The Function Buttons section allows the user to change the values assigned to the M1 M2 and Auto buttons The square next to the M1 and M2 labels indicates the current memory preset value associated with each button Clicking on the square brings up a color selector that allows the user to change the hue saturation and intensity associated with each button The Fade Time field allows the user to change how long the transition to a color selected by the M1 or M2 buttons take The factory defaul
6. the model RC 001 QualColor Touch remote control It provides additional capabilities for the RC 001 including the following 1 Customize the linking attributes Set a new radio channel or change the Network ID to avoid interference with a Continue Introduction Release Notes License Agreement aes Floste Setup Release Notes These are the release notes for version 1 0 of the QualColor Touch Commander utility sofware System Requirements Microsoft Windows Windows XP with service pack 2 Windows Vista or Windows 7 25 MB Spare disk space Spare USB Port Apple Macintosh Mac OS X 10 5 or lat running on an Intel processor 25 MB Spare disk space Spare USB Port Known Issues Introduction Release Notes License Agreement First Time Setup End User License Agreement CAREFULLY READ THE FOLLOWING LICENSE AGREEMENT BY CLICKING ON THE ACCEPT BUTTON YOU ARE CONSENTING TO BE BOUND BY AND ARE BECOMING A PARTY TO THIS AGREEMENT IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS AGREEMENT CLICK THE DO NOT ACCEPT BUTTON AND IF APPLICABLE RETURN THIS PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND License Grant The package contains software Software and related explanatory written materials Documentation Software includes any upgrades modified versions updates additions and copies of the Software You means the person or company who is being licensed to us
7. to the fixture Put the fixture controller into provisioning mode by pressing the Prog button and observing that the Prog indicator is illuminated Put the QualColor Touch remote control into linking mode by pressing the Link Mode button with the unrolled end of a paperclip The red indicator will blink slowly Press the M1 button briefly to re link the remote control to the fixture controller Observe the Prog indicator on the fixture controller is turned off indicating a successful link Press the Link Mode button again on the remote control or wait until the red indicator stops blinking approximately 30 seconds and test operation of the system operating at the new radio channel See the QualColor Touch remote control User Manual for more information on the linking process If this is the second or third pair of remote controls and controllers use the M2 or AUTO button as necessary during the linking step step 5 above 20 Advanced Linking Example Assume there are already three separately operating pairs of QualColor Touch remote controls and fixture controllers and it is desired to add a fourth The first three pairs use the default fixture address values 1 2 3 Pair 1 Zone 1 Unit 1 Active Link 1 Pair 2 Zone 1 Unit 2 Active Link 2 Pair 3 Zone 1 Unit 3 Active Link 3 The fourth pair will be configured to use a fixture address Zone 1 and Unit 4 with the following procedure
8. various attributes in a specific fixture controller Typically this tab is used to set the fixture address to match a changed active link address in the QualColor Touch remote control It may also be used to configure one of the fixture controller s automatic programs to run whenever the fixture controller is powered up for stand alone operation Fixture Address The Fixture Address section shows the address associated with the currently active link and allows the user to change the fixture address It may be used to perform the same action as the linking process described in the QualColor Touch User Manual The currently selected active link is indicated with a green check mark in the QualColor Touch Fixture Addresses section The Zone and Unit fields are initially set with the address configured in the QualColor Touch remote control Selecting a different link in the QualColor Touch Fixture Addresses section updates the Zone and Unit fields to the address associated with that link see the Configure QCTouch tab The Get Fixture Address button allows the user to get the current address of a particular fixture controller The Set Fixture Address button allows the user to set the address in the Zone and Unit fields into a particular controller The program also configures the fixture controller with the currently selected Radio Channel and Network Id see the Configure QCTouch tab The program will prompt the user to press the Prog Button on t
9. LOWING LICENSE AGREEMENT BY CLICKING ON THE ACCEPT BUTTON YOU ARE CONSENTING TO BE BOUND BY AND ARE BECOMING A PARTY TO THIS AGREEMENT IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS AGREEMENT CLICK THE DO NOT ACCEPT BUTTON AND IF APPLICABLE RETURN THIS PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND Th Do Lig We hereby grant yo provides additional capabilities for the RC 001 including the following purpose of configuring or u MacOS X 10 5 or later running on an Intel processor GoBack A special dialogue box is displayed the first time the QualColor Touch Commander program is run This dialogue box displays the following information 1 Introduction 2 Release Notes 3 License Agreement Please note that you must agree to the terms of the license agreement for the program to continue operating Connecting to the QualColor Touch The QualColor Touch Commander program attempts to find the QualColor Touch remote control connected to the computer using the USB interface It displays the following dialogue box while searching for the remote control Connecting to the QualColor Touch Remete Apple Macintosh Platforms Download the qualcolortouch dmg file from the Giulio Lighting website Typically this file will be put in the Downloads folder Open in Finder About Downloads pdf Downloaded file Click to open Opening this disk image file will temporarily mount the Q
10. Make sure the remote control is control is not connected to the connected to a spare USB port computer on the computer and that the power indicator on the remote control is lit Software is not properly Re install the software package installed Found a device but could not Software is not properly Re install the software package connect to it installed A USB Hub between the Connect the remote control computer and the interface directly to a USB port on the device is not compatible with computer running QualColor the QualColor Touch remote Touch Commander control Could not communicate with The Giulio Lighting controller Move the controller closer to the remote device is too far away from the the remote control ideally QualColor Touch remote within 5 feet 2 m control for reliable radio communication There was interference during Attempt the operation again If the LEDlink radio it continues to fail you may communication between the want to change the radio QualColor Touch and fixture channel controller 22 The fixture address was not successfully provisioned Could not verify the fixture address was successfully provisioned The QualColor Touch remote control and fixture controller are not properly linked together The Giulio Lighting controller was not in provisioning mode The controller is too far away from the QualColor Touch remote control for reliable radio communication Th
11. QualColor Touch Commander Installation and User Manual EZ Giulio Lighting The QualColor Touch Commander program is designed to provide additional capabilities with the Model RC 001 QualColor Touch remote control The primary use of the QualColor Touch Commander is to configure advanced attributes of the RC 001 including the following 1 Radio Channel and or Network Id 2 Fade Time and presets associated with the M1 and M2 buttons 3 Program associated with the Auto button 4 Linked Fixture and Fixture Address It provides some additional capabilities including the following 1 Computer control of one or more fixtures including thematic based automatic programs 2 The ability to set a specific Fixture Address and power on program Important Information Please read through the remaining instructions before installing and using this software This software has been designed and tested to operate on the following platforms Its operation on other platform configurations cannot be assured 1 Microsoft Windows Platforms Windows XP with SP2 Windows Vista Window 7 e 25 MB spare disk space e Spare USB Port 2 Apple Macintosh Platforms Mac OS X 10 5 or later running on an Intel Processor e 25 MB spare disk space e Spare USB Port This manual assumes you have read the User Manual for the QualColor Touch remote control Model RC 001 and the Giulio Lighting controller linked to it Do not connect the QualColor Touch remot
12. ddress of the first fixture to be controlled The Number of Fixtures field sets the number of sequentially addressed fixtures starting with the first addressed fixture All fixtures must be set with the same Zone address and with sequential Unit addresses The Zone and Starting Unit addresses are shown on both the Color Dimmer and Dynamic Effects tabs Color Dimmer Color Dimmer Dimmer Dynamic Effects Configure QCTouch Configure Fixture 100 Intensity Color Dimmer Tab in Single Fixture Mode Color Dimmer Dynamic Effects Configure QCTouch Configure Fixture 100 Eiee Arana Zone 1 Unit 1 Selected Fixture OAI Units unit 1 Ounit 2 Ounit 3 Ounit 4 Qunit 5 JUnit 6 JUnit 7 Unit 8 JUnit 9 Unit 10 0 Intensity Color Dimmer Tab in Multiple Fixture Mode The Color Dimmer tab allows the user to interactively change the color and or intensity of selected light fixture s The QualColor Touch must be within range of the light fixture Fixture Address The Zone and Unit fields set the fixture address of the light fixture controller The way the Fixture Address is set and used depends on the current mode Single Fixture Mode is used when the QualColor Touch remote control is linked to a single fixture controller or multiple fixture controllers sharing the same address Multiple Fixture Mode allows the QualColor Touch remote control to operate up to ten fixture controllers each wit
13. e control to the computer before installing the application Connecting the RC 001 to the computer before the software has been installed may cause the operating system to prompt for an installation disk Click the Cancel button if this happens All necessary software will be installed along with the program Revision Information Version 1 1 Added support for multiple fixtures to the Color Dimmer and Effects tabs The feature is enabled through a new properties Microsoft Windows or preferences Mac OS X menu item These tabs can now control up to 10 individually addressed fixtures Added the capability in the Configure QCTouch tab to enable fixture power fail recovery in the RC001 This feature is only enabled with a specific key sequence Contact Giulio Lighting if use of this feature is necessary Added the capability in the Configure Fixture tab to configure to default power on program in a light fixture controller Revamped the help system Version 1 0 Initial release Microsoft Windows Platforms Download the QualColorTouchSetup exe zip file from the Giulio Lighting website You may choose to store it somewhere or open it upon download Unzip the file and start the Setup Wizard fe Setup QualColorTouch Welcome to the QualColorTouch Setup Wizard This will install QualColorTouch 1 1 on your computer It is recommended that you close all other applications before continuing Click Next to cont
14. e the Software or Documentation We and us means Dan Julio Designs LLC dba Giulio Lighting We herehy arant vou a naneyclusive license tn use the A special dialogue box is displayed the first time the QualColor Touch Commander program is run This dialogue box displays the following information 1 Introduction 2 Release Notes 3 License Agreement Please note that you must agree to the terms of the license agreement for the program to continue operating Connecting to the QualColor Touch The QualColor Touch Commander program attempts to find the QualColor Touch remote control connected to the computer using the USB interface It displays the following dialogue box while searching for the remote control QualColor Touch Commander Zone Unit 0 Connecting to the QualColor Touch Remote R eS SS Se ox Intensity Operation A simple control panel is displayed once the program has started and successfully found a remote control Dynamic Effects Configure QCTouch Configure Fixture Zone 1j Unit 1 gt Color QualColor Touch Commander The control panel displays individual tabs for the four functions the program provides 1 Color Dimmer Manually control the selected fixture s from the computer screen 2 Dynamic Effects Let the computer dynamically change the selected fixture s according to a user selected theme 3 Configure QCTouch Configur
15. e various attributes in the QualColor Touch remote control 4 Configure Fixture Set the address or power on program in a specific fixture controller Click on a tab to move between the four main functions Program Preferences The QualColor Touch Commander program sets the default Fixture address Zone and Unit in each tab to the the current link value when it is first run The Color Dimmer and Dynamic Effects tabs will only control fixtures with that specific address This mode is called Single Fixture Mode The program may be configured for the Color Dimmer and Dynamic Effects tabs to operate up to ten sequentially addressed fixtures The Color Dimmer tab may be used to set a different color and intensity value for each fixture The Dynamic Effects tab generates colors for all fixtures according to the selected theme This mode is called Multiple Fixture Mode The Preferences menu item Mac OS X and Properties menu item Microsoft Windows are used to select the mode and to configure Multiple Fixture Mode ee ee Se Color Dimmer Dynamic Effects Configure QCTouch Configure Fixture QualColor Touch Commander Preferences z Commender Er x Zoi 1 J Enable Multiple Fixture Support Unit 1 Number of fixtures 1 10 5 Zone Address 1 Starting Unit Address 1 Preferences Properties The Zone Address and Starting Unit Address fields set the a
16. ere was interference during the LEDlink radio communication between the QualColor Touch remote control and controller The Giulio Lighting controller is too far away from the QualColor Touch remote control for reliable radio communication There was interference during the LEDlink radio communication between the QualColor Touch and controller 23 Use the linking procedure described in the remote control s User Manual to link it with the controller Attempt to provision the controller again Make sure the controller is in provisioning mode by pressing the Prog button and verifying the Prog indicator is lit Move the controller closer to the remote control ideally within 5 feet 2 m Attempt to provision the controller again If it continues to fail you may want to change the radio channel Move the controller closer to the remote control ideally within 5 feet 2 m Attempt to provision the controller again If it continues to fail you may want to change the radio channel Could not get the fixture address The Giulio Lighting controller was not in provisioning mode The controller is too far away from the QualColor Touch remote control for reliable radio communication 24 Try again but make sure the controller is in provisioning mode by pressing the Prog button and verifying the Prog indicator is lit Move the controller closer to the remote control ideally within 5 feet 2 m
17. g either button so the program can communicate with the controller The QualColor Touch must be within range of the controller Note that the fixture controller will respond to commands from the QualColor Touch remote control if a Power On program is running The command from the remote control will take precedence over the running program Examples Changing Radio Interface values Assume that there is radio interference from a Microwave oven that prevents proper operation of the QualColor Touch remote control and fixture it controls The QualColor Touch remote control is in the factory default condition operating on Radio Interface Channel 1 with active link 1 Microwave ovens generally do not emit radio interference across the entire frequency spectrum that the LEDlink interface can utilize Changing to Radio Interface Channel 4 should alleviate the interference The following procedure may be followed to change the Radio Interface Channel in the QualColor Touch remote control and the fixture it controls 1 Connect the QualColor Touch remote to the computer and start the QualColor Touch Commander program Select the Configure QCTouch tab Select Radio Channel 4 and load this into the remote control by pressing the Set QCTouch button Exit the QualColor Touch Commander program and disconnect the remote control from the computer always disconnect the remote control after quitting the program Take the QualColor Touch remote control
18. h a unique address Single Fixture Mode The Zone and Unit fields may be changed to address any fixture These fields are set initially to match the currently active link in the QualColor Touch Either type a new value in the field or use the up down arrow keys to change the value Multiple Fixture Mode The Zone and Unit fields indicate the base fixture address unit address of the first fixture The Selected Fixture buttons allows the user to select the specific fixture unit address to control or all fixtures simultaneously The zone address base unit address and number of fixtures are set using the preferences properties menu item Color Selector The Color selector graphic allows the user to set the hue and saturation of the fixture Click the mouse over the desired hue and saturation to select a new value or drag the mouse in the graphic to change the value dynamically The arrow keys may also be used for precise changes Intensity Slider The Intensity slider allows the user to set the brightness of the fixture Click the mouse along the slider to set a new intensity level or use the mouse to grab the control and then drag the mouse up and down to dynamically change the brightness The QualColor Touch Commander program attempts to get and display the current color dimmer settings from the fixture when the program first starts running and anytime the Selected Fixture is changed in Multiple Fixture mode Dynamic Effects File
19. he fixture controller after pressing either button so the program can communicate with the controller The QualColor Touch must be within range of the controller Fixture Power On Program The Fixture Power On Program section allows the user to select one of the automatic programs to run whenever the fixture controller is powered on The pull down menu selects a program or no program to be configured in the fixture controller There are two automatic programs Random and Sequential Each program has four speed settings The Random program causes the fixture to fade between randomly selected colors for an ever changing display The Sequential program causes the fixture to fade repeatedly between the rainbow colors red yellow green cyan blue magenta and back to red The four speed settings are described below for each of the two automatic programs Speed Random Sequential fade between colors for full color change ee ee Speed Settings The Get Program button allows the user to get the currently configured program in a fixture controller at the address specified in the Fixture Address fields The pull down menu is updated to show the currently configured program The Set Program button allows the user to set the selected program as the power on default in the fixture controller at the address specified in the Fixture Address fields The program will prompt the user to press the Prog Button on the fixture controller after pressin
20. inue or Cancel to exit Setup QualColor Touch Commander Setup Wizard The Setup Wizard allows you to create a shortcut icon on the desktop and or a Quick Launch icon if desired ie Setup QualColorTouch Select Additional Tasks N Which additional tasks should be performed Select the additional tasks you would like Setup to perform while installing QualColorTouch then dick Next Additional icons E Create a desktop icon E Create a Quick Launch icon ee Selecting additional icons Start the QualColor Touch Commander program from the Start menu or by clicking one of the optional icons created by the Setup Wizard Be sure to connect the QualColor Touch remote control to the computer before starting the application First Time Setup Introduction Welcome to the first time setup of the QualColor Touch lit Program Description The QualColor Touch Command utility program is designed for use with the model RC 001 QualColor Touch remote control It e rem into a spare USB port on this computer and the green indicator is Release Notes These are the release notes for version 1 0 of the QualColor Touch Commander utility software System Requirements Microsoft Windows XP with service pack 2 Windows Vista or Windows e 25MB Spare disk space e Spare USB Port Apple Macintosh Introduction Release Notes License Agreement End User License Agreement CAREFULLY READ THE FOL
21. l units configured using the preferences properties menu item Effect The Effect buttons allows the user to select the desired theme Click the button next to the theme name to start an automatic effect program Click the Off button to turn off the program Effects will also be turned off when a different tab is selected All light fixtures configured using the preferences properties menu will be controlled according to the selected theme Speed The Speed slider allows the user to set the rate at which the colors transition from one value to the next Click the mouse along the slider to set a new rate or use the mouse to grab the control and then drag the mouse up and down to dynamically change the rate Note that the computer waits for the current color transition to complete before picking a new one This may result in a long delay when changing speed Configure QCTouch a OLC QualColor Touch Commander Color Dimmer Dynamic Effects Configure QCTouch Configure Fixture Radio Interface Radio Channel Network ID 1 02 03 O4 Function Buttons ws Fade Time sec Auto 1 Random Med Slow Z M2 Fixture Addresses Zone a 1 2 Unit 1 2 B Active 1 02 93 Default 3 Set QCTouch 3 Configure QCTouch Tab The Configure QCTouch tab allows the user to change various operating attributes of the QualColor Touch remote control The tab is organized into three areas 1 Radio Interface
22. nk The Active link used by the QualColor Touch remote control may be changed by selecting one of the three Active radio buttons The address that the QualColor Touch remote control will use for each link may also be changed in the Zone and Unit fields above the link identifier Zone addresses range from 1 65535 Zone addresses 65531 65535 are reserved and should not be used Unit address may range from 1 65535 Click on the Set QCTouch button to load new Fixture Address information into the QualColor Touch remote control Note that the fixture controller must also be configured with the same address as the active link in the QualColor Touch remote control This may be done in one of two ways The first method utilizes the built in linking capability of the remote control and is described in the User Manual It is useful if the controller is already installed and is far from the computer running the QualColor Touch Commander program The second method utilizes the fourth tab Configure Fixture described in the next section Configure Fixture Pancras Color Dimmer Dynamic Effects Configure QCTouch Configure Fixture Fixture Address Zone 1 Get Fixture Address Unit 1 Set Fixture Address QualColor Touch Fixture Addresses Get Program l Set Program Set Program takes effect on next power cycle CMIM AA Configure Fixture Tab The Configure Fixture tab allows the user to change
23. t value for this setting is one second The user may change this value to any value from 0 25 seconds The Auto pull down menu allows the user to change the automatic program assigned to the Auto button There are two automatic programs Random and Sequential Each program has four speed settings The Random program causes the fixture to fade between randomly selected colors for an ever changing display The Sequential program causes the fixture to fade repeatedly between the rainbow colors red yellow green cyan blue magenta and back to red The four speed settings are described below for each of the two automatic programs Speed Random Sequential fade between colors for full color change m nemos isons Speed Settings Clicking the Set QCTouch button will load new Function Button values into the remote control It is not necessary to re link the remote control with any fixture controllers for changes to the Function Buttons to take effect Fixture Addresses As described in the QualColor Touch User Manual each RC 001 remote control contains a built in mechanism for quickly changing the link to support up to 3 separately addressed fixtures The Fixture Addresses area shows the current active link and the fixture address associated with the link Typically this area is used for advanced modifications including linking a fourth or higher remote control and fixture or changing the fixture address associated with a particular li
24. ualColor Touch Commander volume on the desktop Ip n ONE SAO Tue 11 42AM Q E Macintosh HD QualColorTouch E mm oO Q Y DEVICES Macintosh HD Drag QualColorTouch onto Applications to install iDisk gt SHARED gt paces e nool gt p Y SEARCH FOR QualColorTouch Applications Today Yesterday Past Week b G All Images QualColorTouch fm x 2 items 85 5 MB available Drag to install Drag the QualColor Touch icon onto the Applications icon to install the program After the program is installed you may eject the temporary volume and delete the qualcolortouch dmg file if you desire Double click the QualColor Touch Commander icon in the Applications folder to start the program Be sure to connect the QualColor Touch remote control to the computer before starting the application First Time Setup First Time Setup Introduction Introduction Welcome to the first time setup of the QualColor Touch Release Notes Commander utility program This setup will take you through the release notes and license agreement for this version of the software The application will immediately startup once you have accepted the license agreement License Agreement Be sure the RC 001 QualColor Touch remote control is plugged into a spare USB port on this computer and the green indicator is lit Program Description Tho QutiColer Touch Command utility program is designed for use with
Download Pdf Manuals
Related Search