250W Wizard Extreme Scanner
Contents
1. envelopes weaken with age so to reduce the risk of lamp explosion replace the lamp when it reaches the limit of its service life as specified by the manufacturer The following lamp types are supported Osram HSD 250 80 Osram HSD 250 78 Osram HSD 250 60 e Philips MSD 250 2 e Philips MSD 200 Allow the lamp to cool for at least 5 minutes before packing and moving the fixture To avoid possible damage remove the lamp when shipping the fixture Warning Always disconnect the fixture from AC power and allow it to cool for at least 5 minutes before installing the lamp The screws on the lamp plate can reach 90 C 194 F during operation FUSES The Wizard Extreme uses a time delay fuse for protection against current overload If the power LED does not light when power is applied the fuse may be spent If the fuse blows repeatedly there is a fault with the unit that requires service by a Shine technician Never bypass the fuse or replace it with one of another size or rating Replacing the main fuse 1 Unplug the mains cable from the input socket 2 Open the fuse holder which is built into the input socket and remove the fuse 3 Replace the fuse with one of the same type The fuse rating is listed on the serial number label that can be found on the back of the fixture Www storexp com triangle lights gmail com tri 4 ngle lights 6Warning For protection from dangerous electric shock the fixture must be grounded e2. C Pin 5 NC 5 pin to 3 pin 3 pin to 5 pin 3 pin to 3 pin Adaptor Adaptor Phase Reversing Adaptor Male Female Male Female Male Female 1 1 2 2 3 3 pl E PIN 11820005 PIN 11820004 P N 11820006 Www storexp com triangle lights gmail com tri MA ngle lights Terminate the link by inserting a male termination plug P N 91613017 into the data output of the last fixture A termination plug is simply an XLR connector with a 120 ohm 0 25 W resistor soldered across pins 2 and 3 Male Female Termination Plug Termination Plug Male XLR Female XLR 1 1 3 120 Ohm 3 120 Ohm P N 91613017 P N 91613018 6 Maintenance Cleaning the fan and air vents To maintain adequate cooling dust must be cleaned from the fan and air vents The Wizard Extreme fan can be removed from the fixture to give access for cleaning 1 To clean the fan disconnect the fixture from power and allow it to cool completely 2 Pull the two locking pins on the fan up to release it and lift up the outer edge of the fan illustration A www storexp com triangle lights gmail com tris ngle lights w pace quality suppor 4 When the fan is clear of the housing lift it up for access to the fan blades 5 Remove dust from the fan and grille with a soft brush cotton swab vacuum or compressed air 6 Replace the fan in the housing and push down on the two locking pins to secure it www storexp com triangle lights O gmail com tri 4 ngle ligh
3. ER to confirm The display shows ARUN SRUN or SON Or press MODE ESC to cancel the select and then enter Mode o fi S E A Ar Un Master Mode Master auto mode f 5 E 5 ER Master Mode Master sound control mode L Au l Son Slave Mode Salve www storexp com triangle lights gmail com tri ngle lights pr s quality suppor Mode 3 This mode is horizontal scan state Press UP or DOWN to choose PAN or RPAN press ENTER to confirm or press MODE ESC to cancel the select and then enter Mode 4 Pan Mode Positive E PA A Pan Mode Negative Mode 4 This mode is the vertical scan state Press UP or DOWN to choose TIL or RTIL press ENTER to confirm or press MODE ESC to cancel the select and then enter Mode 5 Tilt Mode Positive Tilt Mode Negative Mode 5 This mode is the direction of selection for the LED display Press UP or DOWN to choose DIS or R DIS press ENTER to confirm or press MODE ESC to cancel the select and then enter Mode 6 o E LED Mode Positive rd 5 LED Mode Positive Mode 6 This mode switch control for the lamp Press UP or DOWN to choose LAON or LAOF press ENTER to confirm or press MODE ESC to cancel the select and then enter Mode 7 LRon a on L Aof Lamp off Mode 7 This model for the system reset control Under this mode press ENTER to confirm Reset or press MODE ESC to cancel the select and then enter Mode 8 System
4. arthed The AC mains supply shall have overload and ground fault protection Following the cord cap manufacturer s instructions connect the yellow and green wire to ground earth the brown wire to live and the blue wire to neutral The table below shows some pin identification schemes Wire Pi Marking Screw color brown live E yellow or brass blue neutral ON Silver yellow green ground green po Errors Mistakes and Recommendations Please write me at triangle lights gqmail com for SE emea improvements that you think would make it a better manual We appreciate your help and will offer discounts for your next purchase depending on how much you contribute www storexp com triangle lights gmail com
5. reset Mode 8 This mode is for the restoration of factory settings Under this mode press ENTER to confirm Reset and restoration of factory settings or press MODE ESC to cancel the select and then enter Mode 1 L o A g Lode default www storexp com triangle lights gmail com tri A ngle lights ce quality suppord 4 DMX CHART 66 129 Rotation Speed from fast to slow DA es colorSelecton OOOO 6 cas obo Shake SSS DD 8 ce mo CSS ede aona 10 Rs Pansped Dn oss Color Changing intervals Speed of Cha www storexp com triangle lights gmail com tri 4 ngle lights a pace quality suppa 5 DMX Connections and Set Up DMX Input and Output slots ARE DIFFERENT please read the mark carefully before you link the light DMX OUTPUT DMX INTPUT Pin 1 Screen Pin 2 Signal ein Screen Pin 3 Signal Pin 2 Signal Pin 3 Signal Please do remember to connect one circle circuit plug on the output signal of last equipment lt is a 1200hm resistance between terminals 2 and 3 of the CANON plug which helps to avoid signal flash 5Pins canon plug 3Pins canon socket r 7 Pin 1 GND SCREEN Pin 1 GND SCREEN W rm r Pin 2 Signal Pin 2 Signal PA Pin 3 Signal 5Pins canon socket Pin 1 GND SCREEN Pin 2 Signal Pin 3 Signal Pin 4 NC Pin 5 N C 3Pins canon plug Pin 1 GND SCREEN y Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 4 N
6. tri ngle lights pate que ify suppor 250W Wizard Extreme Scanner USER S MANUAL 1 Specifications Power Consumption Lamp Projecting distance Color Wheel Gobo Wheel Focus Control system DMX Channel Connection Input Voltage Dimension Housing Weight 300W 250W Discharge 15M 1 with 7 Colors 1 with 13 Patterns Yes DMX 512 11 Channels 3 pins XLR sockets 100V 256VAC L55 W52 H21CM Metal 21kgs 5 www storexp com triangle lights gmail com tri A ngle lights Data sockets Power and Data LEDs Power input main fuse power on off switch DIP switch Safety cable eye Mounting bracket Lamp housing Swivel locks Focus rod see illustration below right Cover access screws Measurements are in millimeters Www storexp com triangle lights gmail com tri A ngle lights a pice quality suppor 2 Control Modes Stand Alone Mode Select effects using LCD panel to the left hand side of the light DMX International standard DMX512 signal control Master Slave Mode Sound Active 3 LCD Control Panel Function Setting panel operation Display operation Mode 1 This is default mode press UO or DOWN to select address when receiving DMX512 signal under this mode Receive DMX512 signal when the address shows o O i Mode 2 Press MODE ESC to enter mode 2 You will see 3 states press UP or DOWN to choose MSTA MSTS or SLAV then press ENT
7. ts Cleaning optical components Clean the optical components regularly The presence of smudges or dust on optical surfaces can reduce the strength of the light output and the quality of the effects The following illustration shows the elements that need to be kept clean Use care when cleaning optical components and work in a clean well lit area The coated surfaces are fragile and easily scratched Do not use solvents that can damage plastic or painted surfaces 1 Disconnect the fixture from power and allow the components to cool completely 2 Remove the fixture cover You may want to remove the lamp for cleaning 3 Vacuum or gently blow away dust and loose particles with compressed air 4 Remove stuck particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled water Do not rub the surface lift the particles off with a soft repeated press 5 Remove smoke and other residues with cotton swabs or unscented tissues moistened with isopropyl alcohol A commercial glass cleaner may be used but residues must be removed with distilled water Clean with a slow circular motion from center to edge Dry with a clean soft and lint free cloth or compressed air 6 Replace the fixture cover and lamp access cover before applying power www storexp com triangle lights gmail com tri 4 ngle lights LAMP MAINTENANCE The Wizard Extreme is supplied with an HSD 250W 80 long life discharge lamp installed Lamp
Download Pdf Manuals
Related Search