User`s Manual
Contents
1. Connect the cooler s 4 pin connector Me to the motherboard s CPU Fan header Gal s A Caution Please make sure that PWM Control Mode is activated in the motherboard s BIOS settings AMD Socket Installation Partially unscrew the four bolts located on the base of the CPU cooler Then insert the AMD Clips between the base and the heatpipe cover with the clips bent away from the heatsink p 1 A Caution The holes in the Clip as shown below are matched to the keys on the heatpipe cover for secure Clip installation KS A Caution Take note of the orientation of the Nuts and the Side Caps Peel off the Loading Block cover and attach it to the Backplate with the sticky side facing the center of the Backplate Loading Block Peel off one side of the Double sided Tape and attach it with the sticky side facing the Loading block Then peel off the top cover Double sided a T rs Ta E A Caution N Please make note of the orientation of the Loading Block s Installation Dismantle the CPU cooler retention bracket on the motherboard by unscrewing the four bolts located at each corner method may vary consult the motherboard manual for details Be sure to keep the retention bracket so the stock CPU cooler can be used as2. RAM interference check Any RAM with a height taller than 36mm 1 42 will have interference with the CPU cooler Please check the height of your RAM modules prior to installation ZALMAN COM Installation LGA Intel Socket Installation Intel Socket 2011 V3 2011 User Partially unscrew the four bolts located on the base of the CPU cooler Then insert the Intel Clips between the base and the heatpipe cover with the clips bent away from the heatsink gz Wy op wu Intel Clip The holes in the Clip as shown below are matched to the keys on the heatpipe cover for secure Clip installation Intel Socket 1366 115X 775 User Partially unscrew the four bolts located on the base of the CPU cooler Then insert the Intel Clips between the base and the heatpipe cover with the clips bent away from the heatsink O The holes in the Clip as shown below are matched to the keys on the he Je cover for secure Clip installation Install the Bolts to the Backplate according to the socket type and secure them with Side Caps X Backplate is not needed for LGA 2011 V3 2011 sockets Socket 775 Socket 115X Socket 1366 UN Caution Take note of the orientation of the Nuts and the Side Caps Socket 1366 115X Installation Peel off one side of the Double sided Tape and attach it to the center of the Backplate
3. with the sticky side facing down Then peel off the top cover X Socket 1366 115X Installation does not require the Loading Block Socket 775 Installation Peel off the Loading Block cover and attach it to the Backplate with the sticky side facing the center of the Backplate t we Peel off one side of the Double sided Tape and attach it with the sticky side facing the Loading block Then peel off the top cover Double sided Tape 3 motherboard Backplate is not needed Socket 2011 V3 2011 User Fasten the four Stand offs to the side of the motherboard by aligning the Nuts to the motherboard mounting holes If you were unsuccessful at first attempt you may continue with the installation without the Double sided Tape as it is not a necessary Attach the Backplate assembly to the back component Socket 1366 115X 775 User Stand off ZALMAN CO Ze gt gt 3 A D a Apply thermal grease just enough to thinly cover the CPU surface then fasten the Bolts to isntall the cooler Latch the Fan Fixing Clips to the notches located on the sides of the heatsink Note It is often easier to latch the Fan Fixing Clips one at a time Position the fan as low as possible d in f AA Lowering the fan helps to cool the components on the motherboard ey 5 TOI Le
4. User s Manual CNPS10X Performa CORE N NU AQ Intel Socket LGA 2011 V3 2011 1366 115X 775 CPUs AMD Socket FM2 FM1 AM3 AM3 AM2 AM2 CPU amp APUs To ensure safe and easy installation Please read the following precautions www ZALMAN com Ver 150810 Precautions This cooler must be used with a 120mm fan Avoid inserting objects or hands into the fan while it is in operation to prevent product damage and injuries Do not ingest the Thermal Grease and avoid its contact with skin and eyes If contact is made with skin wash off with water If ingested or irritation persists seek medical attention To prevent possible injuries gloves must be worn while handling this product a Excessive force exerted on the fan may cause damage to the fan and or system Use and keep product away from reach of children m Check the components list and condition of the product before installation If any problem is found contact the retailer to obtain a replacement During transportation of the system the cooler must be removed Zalman is not responsible for any damages that occur during the transport of a system Product design and specifications may be revised to improve quality and performance Specifications 131 L X 96 5 W X 151 H mm Heat Dissipation Areal 6 963cm Dimension Noise Level Bearing Type Control Method Intel Socket LGA 201 1 1366 1156 1155 1150 775 CPUs AMD Sock
5. a backup IN 4 SON _ __4 W A ADI y Dh eV NL N MBEAN Y WLLL Y wW N ZALMAN CO Apply thermal grease just enough to thinly cover the CPU surface then fasten the Bolts to isntall the cooler Latch the Fan Fixing Clips to the notches located on the sides of the heatsink Note It is often easier to latch the Fan Fixing Clips one at a time the back side of the motherboard by aligning the Nuts to the If you were unsuccessful at first attempt you may continue Double sided Tape as it is not a Attach the Backplate assembly to necessary component motherboard mounting holes with the installation without the Position the fan as low as possible naa Lowering the fan helps to cool the components on the motherboard Connect the cooler s 4 pin connector to the motherboard s CPU Fan header A Caution Please make sure that PWM Control Mode is activated in the motherboard s BIOS settings ZALMAN COM
6. et FM2 FM1 AM3 AM3 AM2 AM2 CPU amp APUs Thermal Grease ZM STG2M ver2 gt 2 e Components Common Components v5 Kea Manual Cooler User s Manual NaS Backplate N R Fan Fixing Clips Seee PPPE E858 Side Caps Nuts Loaging Block Thermal Grease Double sided Tape ZM STG2M AMD Components Socket FM2 FM1 AM3 AM3 AM2 AM2 Intel Components Socket LGA 2011 V3 2011 1366 115X 775 Stand off Intel Clip Stand off ZALMAN COM AMD Clip Installation Requirements Space Requirements The cooler s installation requires an unobstructed space of 96 5mm width 131mm length and 151mm height with the CPU as a central reference point Please check if components such as ODDs and PSU protrude into the required space Air Guide Removal Air guides on enclosures must be removed before the cooler s installation since they protrude into the cooler s required space 96 5mm Cooler Orientation As shown in the diagram below it is recommended that the cooler be installed N STK A so that air flows from the cooler toward the Ne enclosure s rear exhaust fan to be released PAC gt lt f S Recommended cooler orientation may differ according to the motherboard model 3 a 4 l lt ots 5 ren AN i Fl CPU and
Download Pdf Manuals
Related Search