PP019/PP020 Passive Probe Instruction Manual
Contents
1. csset 5 to 95 RH 10 to 30 5 to 75 RH 30 C to 40 C 5 to 50 RH above 40 C RH not controlled below 10 C Definitions Measurement Category I measurements performed on circuits not directly connected to mains Measurement Category II CAT measurements performed on circuits directly connected to the low voltage installation Pollution Degree 2 operating environment where normally only dry non conductive pollution occurs Temporary conductivity caused by condensation must be expected 923445 00 Rev A 3 PP019 PP020 Passive Probe EC Declaration of Conformity The product is marked with this symbol to indicate that it conforms to the applicable European Union requirements Low Voltage Directive LVD 2006 95 EC Compliance was demonstrated to the following specification as listed in the Official Journal of the European Communities EN 61010 031 A1 2008 Safety requirements for electrical equipment for measurement control and laboratory use Part 031 Safety requirements for handheld probe assemblies for electrical measurement and test EU RoHS Compliance The probe and its accessories conform to the 2011 65 EU RoHS2 Directive as they have been classified as Industrial Monitoring and Control Equipment per Article 3 Paragraph 24 and are exempt from RoHS compliance until 22 July 2017 per Article 4 Paragraph 3 General Safety Information Observe generall2. 6 923445 00 Rev A Instruction Manual Probe Compensation Proper compensation of the probe is reguired to assure amplitude accuracy of the waveform being measured by matching the probe to the oscilloscope s input Capacitance Compensation should be adjusted whenever the probe is connected to or transferred between oscilloscopes Low Frequency 19 PP020 1 Apply a 1 kHz square wave to the probe or connect to the oscilloscope s calibrator output 2 Adjust the low frequency trimmer located on the 19 20 Compensation Box until you achieve a flat topped square wave like the center illustration in the second figure below Single low frequency trimmer on 19 and PP020 Over compensated correct under compensated waveforms 923445 00 Rev A 7 PP019 PP020 Passive Probe High Frequency 020 only High frequency should rarely require adjustment However if adjustment is required 1 Apply a 1 MHz square wave to the probe lt 0 7 ns rise time 2 Remove the plastic caps from the two high frequency trimmers on the 20 BNC Compensation Box 3 Adjust HF2 then HF1 until you achieve a flat topped square wave like the center illustration in the second figure below Dual high frequency trimmers on 020 JA TAJA Over compensated correct and under compensated waveforms 8 923445 00 Rev A Instruction Manual n Imped PP020
3. 923445 00 Rev A PP019 PP020 Passive Probe Voltage vs Frequency Derating Curve YA Measurement Category ov LLL TTT TTT wv 01111 ev N SS 10 KHz 100 KHz 1 10 MHz 100 MHz 1 GHz 10 923445 00 Rev A Instruction Manual Replaceable Parts Sprung Hook 5 mm Black GND Lead w Alligator Clip BNC Adapter 5 mm Standard Accessory Replacement Kit part number is PKIT4 5MM 101 923445 00 Rev A 11 PP019 PP020 Passive Probe Contact Teledyne LeCroy Teledyne LeCroy Offices World Wide United States and Canada World Wide Corporate Office Teledyne LeCroy Corporation 700 Chestnut Ridge Road Chestnut Ridge NY 10977 6499 Ph 800 553 2769 Sales 1 Applications 2 Service 3 or 845 425 2000 Fax 845 578 5985 contact corp teledynelecroy com teledynelecroy com US Protocol Solutions Group Teledyne LeCroy Corporation 3385 Scott Boulevard Santa Clara CA 95054 Sales and Service Ph 800 909 7211 408 727 6600 Fax 408 727 0800 contact corp teledynelecroy com www teledynelecroy com Support Ph 800 909 7112 408 653 1260 psgsupport teledynelecroy com China Teledyne LeCroy Beijing Rm 2001 Unit A Horizon Plaza No 6 Zhichun Rd Haidian Dist Beijing 100088 China Ph 86 10 8280 0318 0319 0320 Fax 86 10 8280 0316 www teledynelec
4. TELEDYNE LECROY Everywhereyoulook PP019 PP020 Passive Probe Instruction Manual TELEDYNE LECROY Everywhereyoulook 700 Chestnut Ridge Road Chestnut Ridge NY 10977 6499 Tel 845 425 2000 Fax 845 578 5985 teledynelecroy com PP019 PP020 Passive Probe Instruction Manual 2014 Teledyne LeCroy Inc All rights reserved Unauthorized duplication of Teledyne LeCroy documentation materials other than for internal sales and distribution purposes is strictly prohibited However clients are encouraged to distribute and duplicate Teledyne LeCroy documentation for their own internal educational purposes Teledyne LeCroy is a trademark of Teledyne LeCroy Inc Other product or brand names are trademarks or requested trademarks of their respective holders Information in this publication supersedes all earlier versions Specifications are subject to change without notice 923445 00 Rev A May 2014 Instruction Manual Warranty NOTE THE WARRANTY BELOW REPLACES ALL OTHER WARRANTIES EKPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS OR ADEOUACY FOR ANY PARTICULAR PURPOSE OR USE TELEDYNE LECROY SHALL NOT BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER CONTRACT OR OTHERWISE THE CUSTOMER IS RESPONSIBLE FOR THE TRANSPORTATION AND INSURANCE CHARGES FOR THE RETURN OF PRODUCTS TO THE SERVICE FACILITY TELEDYNE LECROY WILL RETURN ALL PRODUCTS UNDER WA
5. 700 Chestnut Ridge Road Chestnut Ridge NY 10977 USA teledynelecroy com
6. RRANTY WITH TRANSPORT PREPAID Teledyne LeCroy warrants this oscilloscope accessory for normal use and operation within specification for a period of one year from the date of shipment Spare parts replacement parts and repairs are warranted for 90 days In exercising its warranty Teledyne LeCroy at its option will either repair or replace any assembly returned within the warranty period to the Customer Service Department of an authorized service center However this will be done only if the product is determined by Teledyne LeCroy s examination to be defective because of workmanship or materials and the defect is not caused by misuse neglect accident abnormal conditions of operation or damaged by attempted repair or modifications by a non authorized service facility The customer will be responsible for the transportation and insurance charges for the return of products to the service facility Teledyne LeCroy will return all products under warranty with transportation charges prepaid This warranty replaces all other warranties expressed or implied including but not limited to any implied warranty of merchantability fitness or adequacy for any particular purposes or use Teledyne LeCroy shall not be liable for any special incidental or consequential damages whether in contract or otherwise 923445 00 Rev A 1 PP019 PP020 Passive Probe Terms and Symbols The following terms appear in this manual CAUTION of potentia
7. l damage to equipment or WARNING of potential for bodily injury Attend to the accompanying information to protect against personal injury or damage Do not proceed until conditions are fully understood and met The following symbols may appear on the product DANGER High Voltage risk of electric shock or burn ATTENTION Refer to Manual DOUBLE INSULATION PROTECTIVE EARTH TERMINAL Introduction The Teledyne LeCroy 019 PP020 are passive high impedance voltage oscilloscope probes designed and calibrated for use with general purpose oscilloscopes having an input impedance of 1 shunted by 16 pF However they may be compensated for use with instruments having an input capacitance between 10 to 30 pF for 19 and 8 to 20 pF for 20 They are compatible with oscilloscopes that automatically detect probe attenuation and adjust their readout accordingly 2 923445 00 Rev A Instruction Manual Specifications m lel mleltUm Model Attn Imped B W Time Length Range Attenuation Ratio 10 1 196 Max Input Voltage Measurement Category 500 Vrms CAT I 1500 V transient overvoltage see voltage derating curve on page 10 Measurement Category 11 400 Vrms CAT II Pollution Degree Pollution Degree 2 as defined in EN 61010 031 Operating Altitude UP to 3000 meters Max Operating Temp 0 C to 450 C
8. roy com cn Service Rm 2002 Ph 86 10 8280 0245 Europe Teledyne LeCroy Europe 4 Rue Moise Marcinhes Case postale 341 1217 Meyrin 1 Geneva Switzerland Ph 41 22 719 2228 2323 2277 Fax 41 22 719 2233 contact sa teledynelecroy com applications indirect teledynelecroy com teledynelecroy com europe Protocol Analyzers Ph 44 12 765 0397 1 Taiwan LeColn Technology Co Ltd Far East Century Park C3 9F No 2 Chien 8th Road Chung Ho Dist New Taipei City Taiwan Ph 886 2 8226 1366 Fax 886 2 8226 1368 sales_twn teledynelecroy com tw teledynelecroy com tw 923445 00 Rev A Instruction Manual Teledyne LeCroy Offices World Wide Japan Teledyne LeCroy Japan Hobunsya Funchu Bldg 3F 3 11 5 Midori cho Fuchu Shi Tokyo 183 0006 Japan Ph 81 4 2402 9400 Fax 81 4 2402 9586 teledynelecroy com japan Singapore Oscilloscopes Teledyne LeCroy Singapore Pte Ltd Blk 750C Chai Chee Road 02 08 Technopark ChaiChee Singapore 469003 Ph 65 64424880 Fax 65 64427811 Korea Teledyne LeCroy Korea 10th fl Bldg 968 5 Daechi dong Gangnam gu Seoul 135 280 Korea Ph 82 2 3452 0400 Fax 82 2 3452 0490 teledynelecroy com kr Singapore Protocol Analyzers Genetron Singapore Pte Ltd 37 Kallang Pudding Road 08 08 Tong Lee Building Block B Singapore 349315 Ph 65 9760 4682 923445 00 Rev A 13 LECROY AA Everywhereyoulook
9. use other bodily injury if not handled properly Keep fingers behind the finger guard of probe body and accessories Do not operate with suspected failures Before each use inspect the probe and accessories for any potential damage such as tears or other defects in the probe body cable jacket accessories etc If any part is damaged cease operation immediately and sequester the probe from inadvertent use Cleaning e Clean only the exterior of the probe cables and accessories Use a soft cotton cloth moistened with a mild detergent and water solution Do not allow any portion of the probe to be submerged at any time e Dry the probe and accessory thoroughly before attempting to make any voltage measurement e Do not subject the probe to solvents or solvent fumes as these can cause deterioration of the probe body cables and accessories 923445 00 Rev A 5 PP019 PP020 Passive Probe Disposal The probe is marked with this symbol to indicate that it complies with the applicable European Union requirements to Directives 2002 96 EC and 2006 66 EC on Waste Electrical and Electronic Equipment WEEE and Batteries This electronic product is subject to disposal and recycling regulations that vary by country and region Many countries prohibit the disposal of waste electronic equipment in standard waste receptacles For more information about proper disposal and recycling of your Teledyne LeCroy product visit teledynelecroy com recycle
10. y accepted safety procedures in addition to those listed N here to avoid personal injury or damage to equipment The overall safety of any system incorporating this accessory is the responsibility of the assembler of the system Connect only to grounded instruments Use only with compatible Teledyne LeCroy oscilloscopes that have their BNC input connected to an earth ground Do not connect the probe reference lead to any point which is at a potential other than earth ground Connect and disconnect properly Connect probe to the oscilloscope before connecting it to the test circuit Disconnect the probe input and reference lead from the test circuit before disconnecting from the oscilloscope Do not connect or disconnect probes while they are connected to a voltage source 4 923445 00 Rev A Instruction Manual Do overload Do not apply any potential to the probe leads that exceeds the maximum rating of the probe Always comply with the Voltage vs Frequency Derating Curve Observe all terminal ratings Observe all markings on the oscilloscope before connecting Consult the oscilloscope product manual for further ratings information Do not remove probe casing Touching exposed connections may result in electric shock Use indoors only within operational environment listed Do not use in wet or explosive atmospheres Keep product surfaces clean and dry Handle with care Probe tips are extremely sharp and may puncture skin or ca
Download Pdf Manuals
Related Search