USER MANUAL
Contents
1. Failures or breakdowns caused by improper use poor assembly or inadequate maintenance as declared in the instructions or the user manual are not covered by this warranty Always keep your receipt or invoice this warranty does not cover products whose serial number or identification has been erased damaged or modified The following acts void this warranty Failure to fulfil the requirements above Improper installation Improper use or installation of inadequate parts Warranty Service Original purchaser must send their Rotor product along with the retailer s original bill credit card receipt or other satisfactory proof of date of purchase of the product Drive Side crank arm right Non Drive Side crank arm left O Semi Integrated Spindle Adjustable lenght Pedal Washer Aesthetic Bolt DO NOT TIGHTEN IT Red Fixed Nut DO NOT TOUCH Steel Adjustment LA bolt NO DO NOT DISASSEMBLE 0 only adjust These instructions and instructions for other Rotor Bike Components products are available for download at www rotorbike com Rotor Componentes Tecnol gicos SL info rotorbike com Pol Ind Conmar C Tajo Nave 6 AJALVIR MADRID SPAIN Tel 34 918843846 Fax 34 918843865 Extractor Cap Sliding Washer Drive Side Crank Bolt Aesthetic Bolt DO NOT TIGHTEN IT 1 Install your chainrings on the drive side crank 72. N SAFETY WARNING This owner s manual contains important and useful information regarding the proper installation operation care and maintenance of your ROTORTM Agilis crankset Carefully read follow and understand the instructions given in this manual You should keep this manual in a safe place for future reference Do not perform any modifications or adjustments that are not outlined in this manual If you have any doubt whatsoever regarding your ability to service or repair this product please take your bicycle to a qualified repair shop for the assistance of a professional mechanic Incorrect installation or service may impair performance and could result in a dangerous situation leading to injury or death Please have this product regularly inspected by a qualified mechanic for any signs of wear Components that have experienced excessive wear cracks deformations or impacts need immediate replacement Failure to perform maintenance could drastically reduce the service life of your Agilis crankset and reduce its performance If you have any questions please contact a professional bike mechanic or your nearest ROTORTM dealer for additional information Caution If any instructions within this User Manual are contrary to the instructions given by the manufacturer of your BB set or pedals contact their service department to explain your plan and request their approval MAINTENANCE Inspect your Agilis cranks for cracks and serious scra
3. If installing Q Rings be sure to regulate them correctly Use a small amount of low or medium strength thread locker on the chainring bolts to prevent them from loosening or creaking 2 Install your BB set Rotor SABB Rotor BB1 or any other Shimano compatible BB set following the instructions for said bottom bracket set 3 Insert the Spindle through the left side of the BB set Tip Strap the crank to the chain stay using a zip tie or Velcro strap to ease later steps of assembly 4 Apply asmall amount of grease to the o ring 8 and place it over the spindle STEPS 1 TO 4 5 Place the Drive Side Crank on the spindle and using an 8mm Allen tool to fasten the Bolt 11 to 26 ft lbs or35N m 6 Using a 10mm Allen tool fasten the Extractor Cap 9 softly screwing approximately 90 11 ft lbs or 15 N m STEP 5 STEP 6 Allen 8 mm Allen 10 mm 35 Nem 15 N m Chainrings are not shown in order to clarify the drawings ADJUSTMENT Ensure that steps 1 6 have been completed successfully before proceeding to the next step 7 If there is too little pressure on the BB bearings evident if there is lateral play tighten the Adjustment Bolt 3 on the left crank tighten it clockwise with a 10mm Allen key If there is too much pressure evident if there is too much rotational resistance loosen bolt 3 loosen it counter clockwise and tighten again very slowly ensuring that the cranks rotate freely withou
4. t excessive play or resistance in the BB set IMPORTANT Be sure that the10mm Allen key reach the bottom of the adjustment bolt 3 and keep it during the assembly step 7 DO NOT TIGHTEN the aesthetic bolts 5 of both crank arms TIGHTEN STEP 7 LOOSEN Allen 10 mm Aesthetic Bolt DO NOT TIGHTEN 8 Before installing the pedals place a washer 6 into the inset position located at each pedal hole 9 Place grease or medium strength removable thread locker on the pedal threads in order to prevent corrosion and noise 10 Tighten the pedal up to a torque of approximately 25 8 ft lbs or 35 N m STEPS 8 TO 10 DISASSEMBLY Slightly loosen the Extractor Cap 9 on the DRIVE SIDE CRANK ARM unscrew it 90 counter clockwise using a 10mm Allen wrench DO NOT DISASSEMBLE THE EXTRACTOR CUP FROM THE DRIVE SIDE CRANK ARM Then unscrew the Drive Side Crank Bolt 11 counter clockwise using a 8mm Allen wrench until the crank arm is free of the tapered hectagon spindle
5. tches looseness damage or weakness before each ride and after every fall or crash If any of the preceding conditions are present do not use your Agilis cranks until they have been repaired or replaced WARNING Continuing to use damaged parts may lead to loss of control of the bicycle and cause injury or death It is the product users responsibility to examine the product on a regular basis to determine the need for service or replacement Cyclist should inspect their bicycle and parts on a regular basis in order to detect damage that may have occurred from normal use and abuse Check all parts for damage and wear before every use Check the chainrings bolts and other fasteners periodically for tightness do not over tighten any of them ROTO AGILIS these suction in USER MANUAL their entirety before REVISED OCT 08 starting the installation process ROT Osi Bike COMPONENTS ROTOR WARRANTY POLICY The Agilis crankset and its components are guaranteed for 2 YEARS against any manufacturer defects or defective materials In the event of a warranty defect Rotor s sole obligation under this warranty is to repair or replace at its option the defective part or product at no charge Moreover in some countries Rotor is obliged to ensure any legal warranty defined by law for the customer s protection Elements subject to wear and breakdowns that the manufacturer is not responsible for are not covered by this warranty
Download Pdf Manuals
Related Search