Installation and Operations Manual Claritech RT-1
Contents
1. location via web interface or SNMP Using Claritech RT 1 one can quickly restart locked up remote servers amp router devices to ensure that the network is fully operational around the clock RT 1 has also an IEC C13 socket input for connecting AC mains to it in order to report the instant mains AC voltage RMS value Using an SNMP manager it is possible to evaluate the capacity of the UPS back up battery by comparing the time interval between mains power failure and UPS failure By charting the incidence and frequency of power failures it is possible to evaluate the correct UPS back up dimensioning Also instant mains AC voltage RMS value is reported useful for investigating poor mains supply cases RT 1 also has one dry contact input Optionally one external temperature temperature humidity sensor can be connected to the sensor port located on the back panel RT 1 reports temperature and relative humidity values using SNMP 1 2 Features 10 Mbps Ethernet connectivity DHCP Static IP NTP synchronization Password protected access Web based configuration and control Mains AC Voltage reporting 1 dry contact input NC NO 1 switched power output 1 input for optional digital temperature or temperature and humidity sensor SNMP v 1 traps for alarm conditions E mail notification based on alarm conditions Customizable HTTP and SNMP ports HTTP and XML API commands Remote FTP firmware update 2 Ports and Wiring FRON2. server E mail sender e mail Username and Password authentication details for mail server Web Access parameters Authentication this field is used for enabling disabling the authentication for the Web Interface Username and Password authentication details for the Web Interface XML HTTP API Authentication this field is used for enabling disabling the authentication for the XML HTTP API 3 4 SNMP Setup Page The Claritech RT 1 device supports SNMP version 1 Parameter values can be read written using the SNMP OIDs see chapter 5 OID List The device can also send traps to a SNMP management application SNMP traps are sent by the device if an event occurs status change on the dry contact input the measured voltage on 220V AC IN port goes outside the configured range the measured temperature goes outside the configured range the measured humidity goes outside the configured range restart condition http 19 O X 6 19216812 91 monitoring network setup snmp setup I 0 setup update logout SNMP Setup Enable v 192 168 1 143 SNMP Setup Page The following SNMP parameters can be configured in this page SNMP Configuration enables disables SNMP SNMP Port allows standard port changing Write Read community used for client authentication in SNMP v1 standard SNMP Traps enables disables SNMP tr
3. water leakage sensors current flow sensors etc 8 Technical Specifications Mains Input 108 240VAC max 10A UPS Input Output 190 240VAC max 10A Power consumption 3W relay energized Operating temp 0 50 deg Celsius Humidity Max 8096 non condensing Mounting Wall tabs optional rack tray 18 120 120 19 Appendix Device Size 44 45
4. Edit View Favorites Tools Help monitoring network setup 1 snmp setup I O setup update logout Monitoring CLR 0001 233VAC 28 8 C 48 0 RH NEN ON OFF Pulse Monitoring Page It can be noticed that at the top of the Monitoring Page there is a navigation bar This bar is present in all the other pages of the device Web Interface in order to facilitate an easy navigation The Monitoring Page provides information about the status of the RT 1 device Digital Input It refers to the dry contact input of the device The status can be Open open circuit or Closed short Temperature If the additional temperature sensor is attached to the RT 1 device this field shows the temperature in Relay output It shows the state of the relay which controls the RELAY OUT AC port located on the back of the device The values of this field can be ON or OFF ON OFF button This button can be used to manually turn on off the above relay Pulse button This button can be used to manually turn on off the Pulse mode of the relay Other settings of the Pulse mode can be configured in the O Setup page of the RT 1 device Mains Voltage This field shows the value in VAC of the mains power supply connected to the 220V AC IN port of the device Humidity If the additional temperature humidity sensor is installed this field shows the air relative humidity in percents 3 3 Network S
5. Installation and Operations Manual Claritech RT 1 SUMMARY 1 Introduction 3 1 1 Product Description 1 2 Features 2 Ports and Wiring 4 3 Configuration of the RT 1 device 5 3 1 Web Interface Logging into the device 3 2 Monitoring Page 3 3 Network Setup Page 3 4 SNMP Setup Page 3 5 I O Setup Page 3 6 Firmware Update page and Logout 4 Application example 13 5 OIDList 14 5 1 Product 5 2 Setup 5 3 Monitor and Control 6 XML and HTTP API Commands 16 7 Additional sensors 7 7 1 Temperature Sensor RT T 7 2 Temperature humidity Sensor RT TH 7 3 Dry Contact Sensors 8 Technical Specifications 18 APPENDIX 19 1 Introduction Claritech RT 1 is a specialized device used for remote monitoring and control of mains and UPS power supply using SNMP The unit monitors the voltage of mains supply alerting the network operations centre about power failures and enabling a fast reaction RT 1 also enables the user to control a power outlet remotely 1 1 Product Description The unit is designed to be used on sites where an Uninterruptible Power Supply unit is present One output from the UPS should supply the RT 1 device In this way the unit can send SNMP traps if the mains power supply is down because the UPS still provides back up power RT 1 has an IEC C13 10A socket output that can be switched via an internal relay This output allows a network manager to power off power on and reboot network devices from any
6. NTEGER disabled 0 ENABLED DISABLED enabled 1 x 2 4 2 0 trapEnabled read write Indicates if this trap entry NTEGER no 0 yes 1 is enabled or not x 2 4 3 0 trapReceiverlPAddress read write Trap receiver IP address pAddress x 2 4 4 0 trapCommunity read write Trap community String SIZE 0 13 0 trapinterval read write Trap Interval NTEGER 1 253 0 maxNumberOfTraps read write Max Number of Traps NTEGER 1 253 oneWireSensor temperature OID Name Access Description Syntax 0 temperatureMin read write Temperature minimum INTEGER 400 1250 value 0 temperatureMax read write Temperature maximum INTEGER 400 1250 value 0 temperatureHyst read write Temperature hysteresis INTEGER 0 1250 0 temperatureAction read write Temperature Action INTEGER noAction 0 sendMail 1 oneWireSensor gt humidity OID Name Access Description Syntax 2 5 2 1 0 humidityMin read write Humidity minimum value INTEGER 0 1000 0 humidityMax read write Humidity maximum value INTEGER 0 1000 0 humidityHyst read write Humidity hysteresis INTEGER 0 1000 0 humidityAction read write Humidity Action INTEGER noAction 0 sendMail 1 14 Syntax INTEGER 0 1000 INTEGER 0 1000 INTEGER 0 1000 INTEGER noAction 0 sendMail 1 Syntax INTEGER noAction 0 maillfO
7. T mClantech On the Front the device has the following ports ETH RJ45 connector for connecting the device to the LAN SENSOR PORT S1 1 x RJ11 connector for connecting the additional Temperature Humidity Sensor SENSOR PORT S2 1 x RJ11 connector for connecting the additional Dry Contact Closure Sensor BACK 220V AC FROM UPS On the Back the device has the following ports 220V AC IN IEC C13 male connector used as AC input for mains voltage measurement RELAY OUT IEC C13 female connector used as software switched AC output having 220V AC power supply from UPS 220V AC FROM UPS wire used as power supply connection 220V AC for the RT 1 device and also as power supply for the RELAY OUT port This wire should be connected to an UPS output in order for the device to work in case of a mains failure 3 Configuration of the RT 1 device The device can be configured by using the ETH port 1 Connect the RT 1 device to a 10 100MB Ethernet network If a direct connection to a PC is desired then a crossover Ethernet cable must be used If the device is connected to a switch router then a straight Ethernet cable must be used 2 Connect any additional sensors to the RJ11 ports if needed 3 Connect the 220V AC IN and RELAY OUT cables to the corresponding ports if needed 4 Connect the power supply to the 220V AC FROM UPS port After connecting the power supply the RT 1 d
8. ap messages IP address IP address of the receiving host for SNMP traps Community string used for client authentication in SNMP v1 standard Trap Interval time interval in seconds for re sending the SNMP trap messages if the condition for sending the traps is still present Max Traps number maximum number of SNMP trap messages sent if trap condition is present Download MIB File button It can be used in order to download the SNMP MIB file of the Claritech RT 1 device 10 3 5 I O Setup Page This page is used for setting the parameters of the temperature sensor humidity sensor mains AC voltage sensor and dry contact input Gor httpy 192 1683 BG 8 1921683132 x ts File Edit View Favorites Tools Help monitoring 1 network setup snmp setup I O setup update logout 10 Setup so 50 fase 6 Change text inchidere CC text deschidere CC test1 test ro test2 test ro 1651301651 ro Setup Page Temperature Humidity and Mains Voltage fields For these parameters Min Max and Hysteresis values can be set Every time the read value coming from this sensors goes out of range an e mail is generated if enabled with appropriate Subject and Message Leaving range is considered when the parameter goes lower than MIN values or higher than MAX Coming back in the range is consider when the parame
9. etup Page This page is used for configuring the network parameters of the RT 1 device 19216812 x toj O BOX monitoring network setup snmp setup I O setup update logout Network Setup Static v 192 168 1 2 255 255 255 0 192 168 1 99 192 168 1 99 clock via net 00 04 A3 AA 17 47 testmailserver com send test e mail ef Dis test testcom Enabled Disabled Network Setup Page IP configuration parameters Static DHCP The IP Address can be static or dynamic DHCP server should be present in the network IP address Subnet mask Default gateway these fields are active if the IP address is static and they are used for changing the device IP network settings DNS this field is mandatory if domain names are used instead of IP addresses By default DNS has the same IP address as Default gateway Time Server and Time Zone these fields are used when an e mail is sent in order to get the accurate time A NTP Network time protocol server IP address should be added in this field Host Name up to 16 symbols it appears as a Subject in sent e mails MAC device MAC address SMTP parameters Mailserver IP port domain or IP address port of SMTP mail server In order to use domain name the IP address in DNS field must be correct SSL Secure Socket Layer is not supported on the mail
10. evice will boot up The factory default IP settings of the RT 1 device are as follows IP address 192 168 1 2 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 1 In order to connect a PC to the RT 1 device a temporary IP address should be assigned to the computer The address should be in the same network For example PC IP adaress 192 168 1 3 PC Subnet Mask 255 255 255 0 PC Default Gateway 192 168 1 2 3 1 Web Interface Logging into the device The RT 1 device can be easily configured using the Web Interface After configuring the above IP settings one should type http 192 168 1 2 in the internet browser address field in order to access the Web Interface If the network settings are correct then the Login Page will load In the Login Page the security authorization data must be entered in order to further configure the device The factory default username and password of the RT 1 device are Default username admin Default password admin Ethernet Controller RT 1 Login Page The controller supports one active session only one user can operate the device If another user tries to login the message Someone s logged in appears The active session will be terminated automatically if the current user stays inactive for 2 minutes 3 2 Monitoring Page After successfully logging in the Monitoring page loads in the browser Gore http 19 2 B 19216812 x File
11. for updating the device firmware IC 19 2 C 19216812 monitoring network setup snmp setup I 0 setup update logout Image Upload Browse Firmware Update Page Further information on how to update the device will be included in the new firmware releases The Logout button from the top navigation bar can be used to logout after the desired settings of the device have been applied 12 4 Application example The below example shows one of the ways the Claritech RT 1 device can be used Mains AC Remote Computer or Other device for SNMP Server example switch 4 IP NETWORK _ router f p 220V AC RELAY OUT AC UPS OUT 220V AC IN PORT Temperature Humidity Sensor Claritech RT 1 UPS AC UPS OUT 220V AC FROM UPS PORT Dry Contact Sensor for example door sensor Example of Claritech RT 1 device usage AC UPS IN In this example the RT 1 device is powered from an UPS unit The 220V AC IN port of the RT 1 device is connected to the mains supply in order to facilitate the measurement of the mains voltage Another device for example switch or router is connected to the RELAY OUT port of the RT 1 unit This way this device can be turned on off or rebooted remotely RT 1 is connected to the IP network using the ETH port Additional sensors can be added to the RT 1 device by connecting them to
12. ol Name digitallnputState relayState relayPulse voltx10Int tempx10Int humix10Int configurationSaved restartDevice OID x 3 1 0 x 3 2 0 x 3 3 0 0 0 0 0 0 6 XML and HTTP Commands XML is sometimes the preferred choice when it comes to M2M communication and system integration The monitored values are transmitted in the status xml file that can be easily processed by software applications Below is the structure of the XML file which is located at http your ip address status xml lt Monitor gt lt Device gt TCW112 CM lt Device gt Device Type lt FWstcw1 12 cmv1 01 lt FW gt Firmware version Digitallnput gt OPEN lt Digitallnput gt Digital input state lt Relay gt ON lt Relay gt Relay state lt AnalogInput gt 5 2 lt AnalogInput gt Analog input value lt Temperature gt lt Temperature gt Temperature value lt Humidity gt lt Humidity gt Humidity value lt Monitor gt The relay can be controlled by sending HTTP commanas Command Description http your ip address r1 1 Turn Relay ON http your ip address r1 0 Turn Relay OFF http your ip address tg1 1 Toggle Relay state http your ip address pli 1 Pulse relay 16 7 Additional sensors The RT 1 device has 2 Sensor Ports on the front side The S1 port is used to connect the T H sensors and the S2 port is u
13. penToClosed 1 maillfClosedToOpen 2 Syntax INTEGER manual 0 temperature 1 humidity 2 analoginput 3 digitallnput 4 INTEGER 1 253 Syntax String SIZE 0 38 Syntax NTEGER closed 0 open 1 NTEGER off 0 on 1 NTEGER off 0 on 1 NTEGER 0 1000 NTEGER 400 1250 NTEGER 0 1000 NTEGER unsaved 0 saved 1 NTEGER cancel 0 restart 1 Description Voltage minimum value Voltage maximum value Voltage hysteresis Voltage Action Description Digital Input Action Description Relay Control Item Relay Pulse Width Description recipient e mail address Description Digital Input State Relay State Relay Pulse Voltage x10 in Integer format Temperature x10 in Integer format Humidity x10 in Integer format Configuration save status SAVED UNSAVED Restart Device Access read write read write read write read write Access read write Access read write read write Access read write Access read write read write read write read only read only read only read write read write 15 Name voltageMin voltageMax voltageHyst voltageAction Name digitallnputAction Name relayControl relayPulseWidth Name recipientEmailAddress analoglnput OID x 2 6 1 0 x 2 6 2 0 x 2 6 3 0 x 2 6 4 0 digitallnput OID x 2 7 1 0 Relay OID x 2 8 1 0 0 recipients OID x 2 9 1 0 5 3Monitor and contr
14. sed to connect dry contact sensor The additional sensors that can be connected to this ports are as follows 7 1 Temperature Sensor RT T The RT T sensor is a digital temperature sensor that provides an option for temperature monitoring The head of the sensor is made of aluminum allowing low thermal resistance to the controlled object The temperature sensor RT T is delivered with 1 meter long cable Technical parameters Operating range 40 to 85 Accuracy 0 5 C Head s dimensions 8x8x23 mm Cable length 1m Weight 40 g Communication interface 1 Wire 7 2 Temperature humidity Sensor RT TH RT TH is a sensor for humidity and temperature monitoring The device integrates basic elements plus signals processing and provides a fully calibrated digital output A unique capacitive element is used for measuring relative humidity while temperature is measured by a band gap sensor Both sensors are seamlessly coupled to a 12 bit analog to digital converter This results in superior signal quality and fast response time Technical parameters Humidity Temperature Operating Range 0 to 100 RH 40 to 85 17 3 0 RH 0 4 C Resolution 0 05 RH 0 01 C Long term drift gt 0 5 RH yr 0 04 C yr Interface 1 Wire Cable length LIYY 1 m 7 3 Dry Contact Sensor The RT 1 is capable of working with any Dry Contact sensor on the market Dry Contact sensors can be for example door sensors
15. ter goes lower than MAX HISTERESYS or higher than MIN HISTERESYS Digital Input Input Setup This filed is used for enabling disabling the dry contact input conditional notifications 11 Email Body Open to Closed Closed to Open These fields should be filled with the notification text sent upon a change of state of the contact closure Relay output Pulse duration This filed defines the time length in seconds for which the relay is active when the pulse mode is used Relay output Relay activated from This field defines the way the relay is activated The relay can be activated automatically depending on the value of the monitored parameter humidity temperature analog voltage and changes on digital input or it can be activated manually Only one parameter can be assigned for relay activation at the same time When manual activation is selected Pulse and ON OFF buttons on Monitoring page are active The duration of pulse for relay activation can be set from 1 to 253 seconds E mail recipients TO CC BCC These fields should be filled in with the e mail addresses where all the e mail notifications will be sent Monitoring page refresh interval This is the amount of time in seconds after which the Monitoring Page will refresh itself If value 0 will be filled then there will be no automatic refresh of the Monitoring Page 3 6 Firmware Update page and Logout This page is used
16. the SENSORS ports The additional devices can be temperature sensor temperature humidity sensor and any dry contact sensor 13 5 OID List The Claritech RT 1 device can be configured and monitored through SNMP Simple Network Management Protocol This could be done using every SNMPv 1 compatible program Parameters that can be changed are grouped according to their functions in the tables below To obtain a valid OID number it is necessary to replace x symbol with 1 3 6 1 4 1 38783 To save the changes configurationSaved OID x 3 7 0 should be set to 1 5 1 Product OID Name Access Description Syntax x 1 1 0 name read only Device name String x 1 2 0 version read only Firmware version String x 1 3 0 date read only Firmware release date String 5 2 Setup network OID Name Access Description Syntax x 2 1 1 0 devicelPAddress read write Device IP address IpAddress x 2 1 2 0 subnetMask read write Subnet Mask IpAddress x 2 1 3 0 gateway read write Gateway IP address IpAddress 2 1 4 0 deviceMACAddress read write Device MAC address OCTET STRING SIZE 6 2 1 5 0 dhcpConfig read write DHCP configuration INTEGER off 0 on 1 ON OFF 0 dns read write Domain Name Server IpAddress Address x 2 1 7 0 hostName read write Host Name String SIZE 0 38 SNMP OID Name Access Description Syntax 2 4 1 0 snmpConfiguration read write SNMP Configuration
Download Pdf Manuals
Related Search