Super NOVA Digital Babyalarm
Contents
1. are switched off Low sensitivity Status indicator D High sensitivity T Child is sleeping Blinking symbol out of range or baby unit off g Indicator for transmission in o o progress a Changing symbols indicate sounds from child all Signal strength indicator Note If the battery symbol blinks in one unit and you hear an alarm every 5 10 seconds this means the battery must be recharged to continue operation The parent unit also gives a signal to indicate a weak baby unit battery but the sound is softer The battery symbol then blinks only on the baby unit Detailed instructions 1 The baby unit and parent unit must be set to the same channel A or B If the units do not display the same channel the channel on one of the units must be switched Press the M key menu and the channel indicator will blink Switch channels using the A or V key then press the M key again to store your programming Note Changed settings will be stored when the unit is turned off If the unit signals a weak battery changes will not be stored 2 The digital code must be the same for the baby unit and the parent unit 1 15 If not switch codes on one of the units This unit must then first be turned off Then press the M key and while depressing it turn on the unit by press ing and releasing the On Off button The digital code number will then blink Then release the M key Change the code using the A or V keys 1 to 15 Then press2. is not connected to the Plug the adapter into the wall outlet and charger to the charger The adapter is connected to a wall If the wall outlet has an On Off switch outlet that does not work this must be on The batteries are not charged The batteries are completely Charge the batteries for two days while Also see above discharged the unit is off The charging indicator 13 on the Battery life is at an end Purchase new battery packs from the charger is on but does not change NOTE Not covered by the warranty dealer from red to green even after 48 hours Grey baby unit display and poor The batteries are completely Charge the batteries for at least 12 range discharged even if low battery is not hours indicated The baby unit is too cold Take the baby unit into a place with room temperature in the parent unit completely and the parent unit codes and or channels on both units The parent unit signals that the Out of range Reduce the distance Local conditions range is exceeded may reduce the range dramatically Try switching channels Charge the batteries for at least 12 hours The baby unit is not switched on Turn the baby unit on The baby unit and the parent unit Check that they display the same letter are set to different channels A or B The factory set IPS code is different Check that the code on the round label on the units in the battery compartment is the same If not contact the dealer Interference while transmit
3. the M key to store the code If the M key is not pressed the unit will automatically return to the original coding after 10 seconds Note Code 0 should only be used if extra long range is required but it does not offer as good protection against interference as digital codes 1 15 3 Then test the set by whistling into the baby unit and check that it can be heard in the parent unit If no sound can be heard check whether the parent unit displays the speak er symbol no symbol speaker and red light diodes B9 are switched off If the symbol is not displayed or you want to adjust the volume this is done by simply pressing the A key several times The red light diodes give you the option of visually monitoring the sound level regardless the volume setting for example if you do not want to disturb others or are in noisy surroundings 4 Place the baby unit vertically close to the child minimum 1 1 5 m The telescopic antenna must always be fully pulled out to ensure that the parent unit is reached 5 Place the parent unit vertically close to where you are Pull out the telescopic antenna if necessary 6 Adjustable sensitivity on the baby unit s microphone Press the S key sensitivity on the baby unit and the ear symbol will blink Use the A or V keys to select high two ear symbols or low one ear symbol sensitivity Press the S key to store the setting Low sensitivity is recommended to avoid interference from traffic time limit
4. Baby Unit Congratulations Thank you for choosing the SuperNOVA Digital Babycall model FD D3 This is a quality product developed for optimal safety and comfort based on new sophisticated technology An electronic babysitter can never replace parental care for a child but it is a practical aid that will ease your worries Please read this user manual carefully and keep it in a safe place Quick start Install the battery packs 11 in the baby unit and the parent unit Plug in the adapters 14 in the chargers 12 and charge the batteries for 12 hours the first time Check that the light indicator 13 lights red If it is not on continuously or it is difficult to make it light up clean the charging contacts underneath the unit and in the charger This may even be required on new units due to oxi dation during transport Use a napkin moistened with window cleaner fluid The units may be used while being charged but should then be allowed to charge for 24 hours the first time Place the baby unit and the adapter cord out of reach of the child around 1 1 5 m from the child Place the front of the unit to face the child Turn on both units by pressing the On Off buttons A3 and B3 The light indicators A2 and B2 will now blink Check that the display shows the same channel A B and digital code 1 15 on both units Test the com munication between the baby unit and the parental unit by whistling into the baby unit If t
5. e baby If this does not help there is nothing that can be done about it but it was nevertheless sounds from your child that first activated your parent unit so you have not been wrongly signalled Interference during transmission may thus be expected because units within a certain area will often use the same fre quency When your SuperNOVA is on standby you will not be disturbed by other baby monitors unless they are adjusted to the same code and the same channel in contrast to other brands You then simply chose your own personal combination among the 15 digital codes and two channels allowing 30 options SDIPS The TROUBLESHOOTING CHART Problem Possiblecause Solution _ The indicator 2 does not light up The unit is not switched on Press the On Off button 3 The display goes out shortly after the The batteries are discharged Recharge the batteries while the unit is unit is switched on turned off Remove the batteries for 30 seconds before switching the unit on The charging indicator 13 on the Poor contact between the unit and Clean the contacts underneath the unit charger does not light or blinks red the charger and in the charger Use a napkin moistened with window cleaner fluid NOTE Do not press the contacts on the charger down into the holes Poor contact between the battery Clean and bend out the battery springs pack and the unit inside the battery compartment Clean the battery pack contacts The adapter
6. ed interference from another baby monitor 7 When the baby unit is out of range the parent unit emits an alarm This is due to safety considerations because walls particularly concrete walls and roofs may significantly reduce the range Metal plates cars caravans may prevent signal reception Placing the baby and or parent unit in a different location may help because radio signals are reflected from objects or persons etc Therefore there will be areas where communication is impossible even across short distances When you press the R key on the parent unit you disable all coding for three seconds This enables you to listen to the channel if there is any traffic on it Alarm tones can be heard under the following circumstances From the Baby Unit The battery is discharged weak beep every 5 10 seconds the battery symbol blinks also signalled by the parent unit From the Parent Unit The battery is discharged every 5 10 seconds the battery symbol blinks Parent unit out of range or baby unit not every 5 10 seconds switched on or different channels the range symbol blinks Using the chargers and batteries Both units may be used while being charged Connect the chargers to the wall outlet using the adapters provided Only these adapters must be used Place the baby unit and the parent unit in the chargers the batteries will then be charged The light indicator on the charger lights red during charging and sw
7. here is a high screeching sound increase the distance to the baby unit or press the V button B8 of the parent unit several times Pull out the telescopic antenna and place the units in a vertical position Some noise during transmission may occur This is due to local conditions physical barriers between the units etc The battery packs should be removed from the units if they are not to be used for an extended period of time Otherwise they will be completely dis charged and ruined or will require many hours of charging while the units are off The batteries must not be left discharged over a long period of time they should be charged at least once a month If you have any problems read the troubleshooting guide carefully before you contact your dealer This will provide answers to most questions Legend Baby Unit Telescopic antenna Light indicator A1 A2 must be pulled out fully when in use blinks every six seconds on standby blinks rapidly when activated A3 On Off button switches power on or off A4 LCD display shows all information about the unit s status A5 Akey eessessessesessesossoe programming function for selecting channel sensitivity and digital code AG S KOY coscescsrsesasesntarssnsees key for programming sensitivity A7 M key seessessesessesossses key for programming channel and digital code A8 V KEY siccstecatisncssheeetesons programming function for se
8. itches to green when the batteries are at full voltage after around 4 6 hours but they should remain in the charger for a few hours more to get a full charge When the green light is on the charger has gone into maintenance charging mode The batteries therefore will not be damaged even if they remain in the charger for a long time The batteries may be recharged up to 500 times as long as they are used properly see Quick start Item 5 Note Rechargeable batteries are consumable articles that gradually decline as they are used Extra batteries may be purchased from your dealer Read the troubleshooting chart if you have any problems Technical specifications we reserve the right to make changes Two sets of environmentally friendly battery packs 3 6 V NIMH 550 mAh Transmission frequency Two channels in the 40 665 40 695 MHz range Working temperature 5 C to 40 C Storage temperature 20 C to 40 C Output power Baby Unit lt 10 mW General The authorities have only allocated a restricted number of frequencies for baby monitors and a very limited output power There may therefore be disturbances from other baby monitors while your baby unit has been activated by sounds from your baby traffic interference This can often be recognized as crackling and or beeping in the speaker If this happens try to switch channels and adjust the baby unit to low sensitivity to avoid it being activated by movements or weak sounds from th
9. lecting channel sensitivity and digital code Parent Unit B1 B2 B3 B4 B5 B6 B7 B8 LCD ch IG ugn symbols 29 A Telescopic antenna should be pulled out when unit in use Light indicator blinks every six seconds on standby blinks rapidly when activated On Off button switches power on or off LCD display shows all information about the unit s status AREY corci ien key for increasing volume programming function for selecting channel and digital code aA PE a key for listening to other traffic see detailed instructions M key essessesessesssssesosso key for programming channel and digital code Y KOY rooncrmnituoa key for decreasing volume programming function for selecting channel and digital code Light diodes visual sound indicator Belt clip and wall mount Battery pack NiMH rechargeable battery pack Charger Charging indicator lights red during charging changes to green when charging is complete see detailed instructions Adapter Baby Unit Parent Unit A A CH g Channel A or B CH g Channel A or B IIC Digital code number IIC Digital code number O no digital code 0 is only O no digital code 0 is only visible when you switch codes visible when you switch codes H Battery level indicator H Battery level indicator Symbol for speaker volume DD Symbol for microphone K No symbol speaker and red sensitivity light diodes B9
10. ting Too great distance between the Reduce the distance units Local conditions interference Move the units slightly Local conditions cannot be changed Try turning off light dimmers or other noise sources Units rarely have a defect Volume is too high Adjust the volume charger switches to green contact the dealer Short range Ruined or spent batteries Check the batteries as mentioned above Antenna not pulled out Pull out both antennas Local conditions Other baby alarms in the vicinity may reduce range dramatically Try to switch channels or move the baby unit and or parent unit It takes a long time from when the This is entirely normal The parent unit needs time to check that the correct baby baby starts crying until you can hear unit is trying to establish contact it on the parent unit Other baby alarms may be near by especially if the delay is very long
Download Pdf Manuals
Related Search