Manual - Acceed
Contents
1. Optional 19 rack mount frame is also available for all models amp ANALOG ROCK MOUNT Industry LCD Display User s Manual 25 LCD Displays OPD 212A 215A 217A Chapter On Screen Display Control Industry LCD Display User s Manual 26 LCD Displays OPD 212A 215A 217A On Screen Display OSD Controller The LCD monitor is very easy and simple to operate There are five controls below on the rear panel Y ou can see their respective indicators 0006 AUTO To auto adjust image position pixel clock and phase Whenever there is flicker happens always press the AUTO button first The setting value will be automatically adjusted correctly and saved Notice The OPD series displays were designed to provide the best quality in 60 75MH z VGA frequency range We recommend keeping the screen refresh rate within the range in order to obtain the optimum quality Industry LCD Display User s Manual 27 LCD Displays OPD 212A 215A 217A MENU Menu To activate the OSD Menu press the Button When locating an item you like to adjust in the OSD Menu press to bring up the corresponding sub menu for options A Increase Moving UP Button To move the locating cursor forward in the OSD Menu press UP button To increase the value while adjusting a parameter press the A button M Decrease Moving DOWN Button To move the locating cursor backward in the OSD Menu press the Y button To decrease the val2. Vertical position of the image OSD Pos To adjust the Horizontal amp Vertical position of the O SD Menu Speed En and Speed Adjust To adjust OSD Menu display speed Press Return to previous menu lt Language gt Only English is available Industry LCD Display User s Manual 33 LCD Displays OPD 212A 215A 217A lt Recall gt When you run the function the monitor will be setting to the last status of the saving value lt Save Exit gt To save all setting value and exit lt Cancel Exit gt To cancel all setting value and exit Hotkey Control The Hot key control allows you to instant activate frequent use function without browsing OSD menu l O AUTO After power on press the AUTO button for 3 5 seconds The monitor will reset the parameters to default value Industry LCD Display User s Manual 34 LCD Displays OPD 212A 215A 217A Chapter Drivers Installation Industry LCD Display User s Manual 35 LCD Displays OPD 212A 215A 217A The first time you start Windows with a new monitor the system will detect OPD display and automatically detect and install the Plug and Play device driver However manual installation might be needed when your video card does not comply with DDC1 DD CB2 standard the system can only detect Windows D efault Monitor not the O PD displays When your system detects Windows D efault Monitor or cannot detect the display at all follows the step by step installation g
3. hardware click Next lt Back Next gt Cancel Industry LCD Display User s Manual 44 LCD Displays OPD 212A 215A 217A 11 The Digital Signature N ot Found window will appear click Yes then click Finish Digital Signature Not Found x The Microsoft digital signature affirms that software has been tested with windows and that the software has not been altered since it was tested The software you are about to install does not contain a Microsoft digital signature Therefore there is no guarantee that this software works corectly with Windows OPD 217A If you want ta search for Microsoft digitally signed software visit the Windows Update Web site at http windowsupdate microsoft com to see if one is available Do you want to continue the installation No More Info 12 Now the new drivers are installed to your computer Upgrade Device Driver Wizard Completing the Upgrade Device Driver Wizard m OPD 217A An eror occurred during the installation of the device Access is denied To close this wizard click Finish Bact Finish Barcel Industry LCD Display User s Manual 45 LCD Displays OPD 212A 215A 217A Touchscreen Driver Installation For Touchscreen installation please refer to the excel file ReadMe_All Prods T ouch list xls to find out your match touscreen type and follow the installation guide in respective folders For the following models please u
4. the computer and the LCD monitor before connecting them 7 Use the Monitorto PC VGA cable to connect the LCD monitor to your computer The cable heads are the same on either side m Fasten the connections securely Industry LCD Display User s Manual 20 LCD Displays OPD 212A 215A 217A VGA Port Connector Itisa DB 15 VGA connector The following table shows the pin out assignments of this connector Red Blue GND SaNa Pin Pa Saa m fif N C N C O S Industry LCD Display User s Manual 21 LCD Displays OPD 212A 215A 217A Serial Ports Connector for Touch It isa DB 9 COM Port connector The following table shows the pin out assignments of this connector Signal Name Pin in Signal N ame Not Used eei RX D Receive Data Spe ere e e e L swp Gmna s x ww efe Industry LCD Display User s Manual 22 LCD Displays OPD 212A 215A 217A Panel Mounting These display panels can be placed on a shelf or table or mounted onto the wall To mount them onto the wall you need the mounting brackets which you will find in the accessory box Follow the steps described below e Slide the display panel into cutout on the wall e Tighten the brackets until the display panel is firmly secured to the wall Industry LCD Display User s Manual 23 LCD Displays OPD 212A 215A 217A Industry LCD Display User s Manual 24 LCD Displays OPD 212A 215A 217A Rack Mounting Optional
5. LCD Displays OPD 212A 215A 217A OPD 212A 215A 217A Open Frame Industrial LCD Displays OPD Series Manual V 2 Oct 2003 Industry LCD Display User s Manual i LCD Displays OPD 212A 215A 217A Copyright Notice This documentis copyrighted 2003 byAAEON Technology In All rights are reserved The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of the original manufacturer Information provided in this manual is intended to be accurate and reliable However the original manufacturer assumes no responsibility for its use nor for any infringements upon the rights of third parties which may result from its use The material in this document is for produc information only and is subject to change without notice Industry LCD Display User s Manual 1 LCD Displays OPD 212A 215A 217A Packing List TheLCD monitor comes with the following standard parts shown as below Check and make sure they are included and in good condition If anything is missing or damaged contact the dealer immediately Industrial D isplay Panel x 1 pc Industrial Display Panel User s Manual CD ROM x 1 pc Power adapter x 1 pc VGA Cable 1 8Mx1pc Panel Mounting K its Screws bag Adapter cable saddle Cable RS 232 opti
6. Manual 52 OPD 212A 215A 217A LCD Displays Exploded Diagram OPD Series FRONT 53 Industry LCD Display User s Manual LCD Displays OPD 212A 215A 217A OPD Series BACK Industry LCD Display User s Manual 54
7. al Viewing Angle Vertical 160 Resolution 1024x768 Display Modes Full Screen in 640x480 800x600 1024x768 Mode Color 256K Power Consumption On Working 60Watts Max Input Voltage AC 100 240V 1 8A 50 60Hz Output DC 12V 5A Max Industry LCD Display User s Manual 49 LCD Displays OPD 212A 215A 217A OPD 217A Color TFT Diagonal 17 260cd m TYP Back light MTBF 40 000hrs Contrast Ratio 400 1 0 264 H x 0 264 V mm 1600 Horizontal Viewing Angle Vertical 160 Resolution 1280x1024 Display Modes Full Screen in 640x480 800x600 1024x768 1280x1024 Mode Color 256K Power Consumption On Working 60Watts Max Input Voltage AC 100 240V 1 8A 50 60Hz Output DC 12V 5A Max Industry LCD Display User s Manual 50 LCD Displays OPD 212A 215A 217A Troubleshooting To solve the following problems you may need to refer to Appendix A Standard Timing for compatible display specifications L Problem Unclear or Unsteady Display Actions 1 Activate the AUTO button You might need to repeat to find balanced values for a good quality If the AUTO button cannot solve the problem try to manual fine tune following steps below 1 Tf the image size does not fit the screen adjust the Size setting value under Quality menu 2 If there is image pixel noise appears adjust the Phase setting value under Quality menu Pull and adjust the value bar to find out what is the best c
8. eseeesssees 2 Safety amp War vamly ccccccccccccsssssssssscsssssssssessssssssssscsseessssseeesssssssssesseees 3 Chapter 1 General Information INGO MUCHON sssies ances atin tue bovnetieetuancencen aei tate 8 Open Frame Structure lUStration c cscsesesesesesssssssseseessesssneeneenes 9 Features of Display Panels c cscssssssssssessesesssssssssssssnsssssecsesseseneeseeess 10 General Specifications cscssssssessssssssessssnesesssnssssssscesssessnesessnesneanees 11 DIMENSION ss sssini en e 13 Waterproof Sponge Position ssessssssesssseessssseessesssteesesssteseesssteesessseene 15 Chapter 2 H ardware Installation Before Unpacking arei AA 18 Connecting PoWeliic3 tanan a a a a a 19 Connecting the Compiler erisera a aE EA A raei 20 VGA PO CONMGCHOR nn eie E E ent 21 Serial Ports Connector for Touch seessesssecssecseesseeseesneesseesneeeseenneees 22 Panel Mounties r A A A 23 Rack Mounting O ptional seers 25 Chapter 3 On Screen Display Control On Screen Display O SD Controller s sssssssssssessseesssssssresssssrerssssseees 27 Chapter 4 Drivers Installation Display D river Installation c cssssessessssscsessscsecseesseessessesscnseseesseeseanes 36 Touchscreen D river Installation essessssssssscessecsnseesssecesseessseesnneesn 46 Industry LCD Display User s Manual 5 LCD Displays OPD 212A 215A 217A Sped canons rsin RAAE N RA AE E 47 Troubleshoot eie N EN vet EEE 51 Exploded Darai aener
9. ified service personnel should open the equipment 14 If any of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture Industry LCD Display User s Manual 3 LCD Displays OPD 212A 215A 217A d The equipment does not work well or you cannot get it to work according to the users manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage 15 DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW 20 C 4 F OR ABOVE 60 C 140 F IT MAY DAMAGE THE EQUIPMENT FCC Safety This device complies with Part 15 FCC Rules j I Warning Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution D anger of ex plosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer D ispose of used batteries according to the manufactures instructions Industry LCD Display User s Manual 4 LCD Displays OPD 212A 215A 217A Contents Copyright Notice x seicascisciecercnicccredhownema amas 1 Packing List ccccccccsssssssssssssssssescscsssssssessscsssssssssscessssssssesesssssssue
10. isplay Panels This menu provides full range of analog interface LCD panels which are 12 1 SVGA 15 XGA and 17 SX GA high brightness long lifetime TFT LCD monitors Stainless steel open frame architecture 12 1 SVGA 800x600 resolution 15 XGA 1024x768 resolution 17 SXGA 1280x1024 resolution colorT FT LCD display Analog RGB signals directly input with A D board interface offering multi scan function RS 232 Adapter VGA terminals and AV S Video input OSD On Screen Display function for display adjustment Touchscreen Optional AC in DC out extemal power adapter Swivel ARM VESA 75 100 Standard Aluminum front bezel O ptional Auto detect NTSC PAL Adapter holder Industry LCD Display User s Manual 10 LCD Displays OPD 212A 215A 217A General Specifications Construction Stainless steel open frame architecture Mounting Panel mount or Swivel ARM Input signal RGB Composite video S Video Control OSD On Screen Display on the rear panel PowerSupply external power adapter Dimension OPD 212A 350 W x 275 H x 48 7 D mm without bezel 366 W x 291 H x 49 7 D mm with standard bezel 483 W x 310 H x 49 7 D mm with rack mount bezel OPD 215A 428 W x 320 H x 53 3 D mm without bezel 444 W x 336 H x 54 3 D mm with standard bezel 483 W x 354 80 H x 54 3 D mm with rack mount bezel OPD 217A 482 W x 398 H x 57 2 D mm witho
11. larity range for your LCD display 3 If the image is not centered after step 1 and 2 adjust Image Position under Position menu to center the image 4 Ifyou still have problem to fine tune the image call your local technical support for assistance 2 Problem No Display is shown on the LCD monitor Actions 1 Make sure the LCD monitor is powered on by checking if the Power LED is lit Check if all the connections are secure and the system is running correctly 2 If thepower LED lights up green but there is still nothing displayed connect your PC with another Industry LCD Display User s Manual 51 LCD Displays OPD 212A 215A 217A external monitor If your PC works properly with that monitor then it is possible that the VGA card timing of the system may be outside the LCD monitor s synchronous range Y ou may need a qualified technician for help 3 Problem Not Supported Mode is shown on the display Action This could be a mistake you made in the OSD menu while choosing the INPUT SOURCE RGB or VEDIO Or it is possible that you have chosen a timing that is outside the LCD monitor s synchronous range Recall the factory default values may help to bring the screen back to normal 4 Problem The LCD monitor does not work properly under Windows but it functions all right in DOS mode Action Make sure the display mode you choose in Windows matches the LCD monitor Industry LCD Display User s
12. onal peo nor EF UN Waterproof Sponge It is better for you to keep the carton and the packing materials in case you might need them for packing or moving in the future Industry LCD Display User s Manual 2 LCD Displays OPD 212A 215A 217A Safety amp Warranty 1 Read these safety instructions carefully 2 Keep this user s manual for later reference 3 Disconnect this equipment from any AC outlet before cleaning Do not use liquid or spray detergents for cleaning Use a damp cloth 4 For pluggable equipment the power outlet must be installed near the equipment and must be easily accessible 5 Keep this equipment away from humidity 6 Put this equipment on a reliable surface during installation D ropping it or letting it fall could cause damage 7 The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS 8 Make sure the voltage of the power source is correct before connecting the equipment to the power outlet 9 Position the power cord so that people cannot step on it Do not place anything over the power cord 10 All cautions and warnings on the equipment should be noted 11 Ifthe equipment is not used for along time disconnect it from the power source to avoid damage by transient over voltage 12 Never pour any liquid into an opening This could cause fire or electrical shock 13 Never open the equipment For safety reasons only qual
13. ry LCD Display User s Manual 30 LCD Displays OPD 212A 215A 217A lt AutoT une gt To automatically tune the display to the best image size position and phase lt Brightness gt To adjust the brightness level of the image using up and down arrows button lt Contrast gt To adjust the difference between the light and dark areas using up and down arrows button Industry LCD Display User s Manual 31 LCD Displays OPD 212A 215A 217A lt Color gt 9300 To set the color temperature to 9300K 7500 To set the color temperature to 7500K 6550 To set the color temperature to 6550K User To set the RGB color temperature by user defines Press Return to previous menu lt Q uality gt ADV TUNE Size Phase Text Gfx Sharpness Return ADV TUNE To further tuning the image size phase and sharpness Please make use of this feature whenever the VGA input has been changed Size To expand the image of full screen or to shrink theimage to normal 1piexl to 1piexl Industry LCD Display User s Manual 32 LCD Displays OPD 212A 215A 217A Phase To adjusts the phase of pixel frequency Use the function when there is a pixel noise Text Gfx To exchange to the text orgraphic mode Not for Windows O S Sharpness To adjust sharpness of the image Press Return to previous menu lt Position gt Image Pos OSD Pos Speed En Speed Adj Return Image Pos To adjust the Horizontal amp
14. se the Combo T oolkit to install OPD 215AT D1 OPD 215AT D 2 OPD 215ABT D1 OPD 215ABT D2 OPD 215ART D1 OPD 215ART D2 OPD 217AT D1 OPD 217AT E1 OPD 217ABT D1 OPD 217ABT E1 OPD 217ART D1 OPD 217ART E1 Industry LCD Display User s Manual 46 LCD Displays Specifications Brightness Back light MTBF Pixel Pitch Viewing Angle Horizontal Viewing Angle Vertical Resolution Display Modes Color Power Consumption On Working Input Voltage Output Industry LCD Display User s Manual OPD 212A 215A 217A Color TFT Diagonal 12 1 250 cd m2 TYP 50 000 hrs 0 3075 H x 0 3075 V mm 1200 900 800x600 Full Screen in 640x480 800x600 Mode 256K 60Watts Max AC 100 240V 1 8A 50 60Hz DC 12V 5A Max 47 LCD Displays OPD 212A 215A 217A OPD 215A D Color TFT Diagonal 15 250 cd m2 TY P Back light Life time 30 000 hrs Pixel Pitch 0 297 H x 0 297 V mm Viewing Angle 160 Horizontal Viewing Angle Vertical 1509 Resolution 1024x768 Display Modes Full Screen in 640x480 800x600 1024x768 Mode Color 256K Power Consumption On Working 60Watts Max Input Voltage AC 100 240V 1 8A 50 60Hz Output DC 12V 5A Max Industry LCD Display User s Manual 48 LCD Displays OPD 212A 215A 217A OPD 215A E Color TFT Diagonal 15 Brightness 250 cd m2 TYP Back light Life time 50 000 hrs Pixel Pitch 0 297 H x 0 297 V mm Viewing Angle 160 Horizont
15. t do you want the wizard to do Search for a suitable driver for my device recommended Display a list of the known drivers for this device so that can choose a specific driver lt Back Cancel Industry LCD Display User s Manual 43 LCD Displays OPD 212A 215A 217A 9 In the next window click Have Disk then Install From Disk window will pop up click Browse the Located File will pop up Look for the inf file extension for drivers update Upgrade Device Driver Wizard Select a Device Driver ate Which driver do you want to install for this device wy C Select the manufacturer and model of your hardware device and then click Next If you have a disk that contains the diver you want to install click Have Disk Models Show compatible hardware Have Disk Show all hardware of this device class ose 10 In the next window click Have Disk then Install From Disk window will pop up click Browse the Located File will pop up Look for the inf file extension for drivers update Upgrade Device Driver Wizard Start Device Driver Installation om The device driver will be installed with the default settings wy The wizard is ready to install the driver for the follawing hardware device J PD 217 E OPD 217A Windows will use default settings to install the software for this hardware device To install the software for your new
16. tia 53 Industry LCD Display User s Manual 6 LCD Displays OPD 212A 215A 217A Chapter General Information Industry LCD Display User s Manual 7 LCD Displays OPD 212A 215A 217A Introduction Congratulations on your purchase of the Industry Display Panel TFT LCD monitor a marvelous contribution of cutting edge technology The LCD monitor has been designed with serious thoughts to present the best performance for most applications Symbol of elegance its compact and slim profile is well suited in working locations where space is at a premium The TFT LCD monitor displays sharper more brilliant crisper and flicker free images Complying with the power management regulations of VESA DPMS the LCD monitor is extremely energy efficient and a power saver Plus the LCD monitor has extremely low radiation emissions and near zero electromagnetic fields which are supreme benefits Fully compatible with PC system the LCD monitor provides full interface for all sorts of related standards Supported by Plug amp Play complying with DD C1 DD C2B installing the LCD monitor is absolutely trouble free The On Screen Display menu provides user a convenient interface to make right adjustment for optimum display performance Industry LCD Display User s Manual 8 LCD Displays OPD 212A 215A 217A Open Frame Structure Illustration Industry LCD Display User s Manual 9 LCD Displays OPD 212A 215A 217A Features of D
17. ue while adjusting a parameter press Y button l Power Switch Push up the Power Switch to turn on off the LCD monitorbacklight and the power LED will light up G reen Red Industry LCD Display User s Manual 28 LCD Displays OPD 212A 215A 217A Display Menu There are twelve options in the OSD Menu Press the Menu button to choose the items you would like to adjust lt Main Menu gt ADB100A AAEON Inc InputSource PIP Enable AutoT une Brightness Contrast Color Quality Position Language Recall Save Exit Cancel Exit lt InputSource gt Select PC or Composite Video Input Source Industry LCD Display User s Manual 29 LCD Displays OPD 212A 215A 217A To scroll through items and locate for adjustment in each page presses Menu button to select The display will automatically shut down when there s no input source been selected Source input diagram 6 8 DC in Jack VGA Video in S Video Touch screen AVideo SVideo lt PIP enable gt Picture in picture enable function allows you to view screen with VGA input and Avideo or SVideo sources at same time Use up and down arrows to select major viewing source Press Menu to enter your selection The second input source window will be displayed on the bottom right comer Combinations are as follows VGA main source Avideo 224 source VGA main source SVideo 224 source Press Return to previous menu Indust
18. uide below The drivers for manual installation are provided in the supporting CD ROM Display Driver Installation Windows 98 1 Insert the supporting CD ROM into your CD ROM Driver 2 Click Start button and look for Control Panel under Settings menu Industry LCD Display User s Manual 36 LCD Displays OPD 212A 215A 217A 3 Double click the display icon in the control panel os i Ele Edt Vew Help m E 1 E a8 p 32bit 3Com Accessibi AddNew AddRem Adobe Date Time peppy Find Fast ODBC PA Opbons Hardware Programs Gamma 6429335 4 E Tntemet Joystick Keyboard Mail Modems Mouse Multimedia Network ODBC C E O s 2 E Power Pnnters Regonal Sounds System Users Senings 4 From the Display Properties window select the settings tab Click the Advanced Properties button on the bottom right corner Display Properties 2 xi Background Sereen Saver Appearance Settings r Color palette Hien Color 16 bit gt Les More Em E 800 by 600 pixels Font size iman Fonts J Normal size 96 dpi 7 Show settings icon on task bar Industry LCD Display User s Manual 37 OPD 212A 215A 217A 5 Select the Monitor tab Click the Change button in the top right comer Advanced Display Properties Industry LCD Display User s Manual 38 LCD Displays OPD 212A 215A 217A 6 Now the Update Device Dri
19. ur hardware device Industry LCD Display User s Manual 40 LCD Displays OPD 212A 215A 217A Windows 2000 1 Repeat steps 1 4 as in Windows 98 setup 2 Select the Monitor tab Click the Properties button Plug and Play Monitor EAE General Adapter Monitor Troubleshooting Color Management m Monitor Type m Plug and Play Monitor Monitor Settings Refresh Frequency 60 Hertz Industry LCD Display User s Manual 41 OPD 212A 215A 217A 6 Select Driver tab then click Update Driver Plug and Play Monitor Properties Industry LCD Display User s Manual 42 LCD Displays OPD 212A 215A 217A 7 The Upgrade D evice Driver Wizard will pop up Then Click Next Upgrade Device Driver Wizard Welcome to the Upgrade Device Driver Wizard This wizard helps you upgrade a device driver for a hardware device To continue click Next ier Cancel 8 The Upgrade Device Driver Wizard will pop up Then Click Next Upgrade Device Driver Wizard Install Hardware Device Drivers NAN device driver is a software program that enables a hardware device to work with a an operating system This wizard upgrades drivers for the following hardware device m Plug and Play Monitor gt Upgrading to a newer version of a device driver may add functionality to or improve the performance of this device Wha
20. ut bezel 483 W x 399 H x 58 2 D mm with standard bezel 483 W x 399 H x 58 2 D mm with rack mount bezel Industry LCD Display User s Manual 11 LCD Displays OPD 212A 215A 217A Net Weight OPD 212A 5 5K g OPD 215A 6 5K g OPD 217A 15 36K g Touchscreen Optional m Type 8 wire or 5 wire Analog resistive Resolution gt 1024x1024 for OPD 212A OPD 215A gt 4096x4096 for OPD 217A Light transmission e OPD 212 OPD 215 75 e OPD 217 76 2 Controller RS 232 interface Environmental Specifications Operating temperature 0 C to 45 C 32 113 F m Vibration 5 500Hz 1G random vibration m Shock 15G peak acceleration 11 msec D uration m EMI FCC CE Class A m Safety UL for O PD 215 E series only Industry LCD Display User s Manual 12 LCD Displays OPD 212A 215A 217A Dimensions OPD 212A Unit mm Front Bezel Size Chassis Cutout Size 333 258 mm LCD Cutout Size 248 4 186 9 mm OPD 215A Unit mm Front Bezel Size Cutout Size 405 299 mm Industry LCD Display User s Manual 13 LCD Displays OPD 212A 215A 217A OPD 217A Unit mm 6 0 Front Bezel Size Cutout Size 449 365 mm Industry LCD Display User s Manual 14 LCD Displays OPD 212A 215A 217A Waterproof Sponge Position Inside sponge a Tear off the protection paper on the self adhesive side of the inside sponge b Stick the sponge on the recessed area of the Aluminum bezel or customer s own bezel Front Be
21. ver Wizard opens Confirm by clicking Update Update Device Driver Wizard This wizard searches for updated drivers for Unknown Device A device driver is a software program that makes a hardware device work Upgrading to a newer version of a device driver may improve the performance of your hardware device or add functionality 7 Select Display a list of all drivers in a specific location so you can select the driver you want and press N ext Update Device Driver Wizard What do you want Windows to do Search for a better driver than the one your device is using now Recommended lt Back Cancel Industry LCD Display User s Manual 39 LCD Displays OPD 212A 215A 217A 8 Now click the Have disk button in the bottom right corner Another window appears select the Browse button Look for the inf file extension for drivers update Update Device Driver Wizard f Select the manufacturer and model of your hardware device IF you have a El disk that contains the updated driver click Have Disk To install the updated driver click Finish Models OPD 217A Show compatible hardware rave Diki C Show all hardware lt Back Ners Cancel 9 Close Update Device Driver Wizard by click Finish to complete the installation Update Device Driver Wizard im OPD 217A Windows has finished installing the driver you selected for yo
22. zel Back Side Industry LCD Display User s Manual 15 LCD Displays OPD 212A 215A 217A Outer sponge Press to close the outer sponge to the edge of the Panel PC uter Sponge Front Bezel Sponge with adhesive Industry LCD Display User s Manual 16 LCD Displays OPD 212A 215A 217A Chapter Hardware Installation Industry LCD Display User s Manual 17 LCD Displays OPD 212A 215A 217A Before Unpacking It is very important to locate the LCD monitor in a suitable environment The surface for placing the LCD monitor should be stable and level Make sure the place has good ventilation and out of direct sunlight away form sources of excessive dust dirt heat water moisture and vibration Convenience for connecting the LCD monitor to the related facilities should be well considered too Industry LCD Display User s Manual 18 LCD Displays OPD 212A 215A 217A Connecting Power To poweron the LCD monitor use the provided AC DC adapter and the power cord to connect to the power output socket of the monitor Fasten the connections securely A Surge Protection device plugged between the AC DC adapter and the wall outlet is recommended to prevent the effects of sudden current variations from reaching the LCD monitor The sudden peaks of electricity may harm the LCD monitor Industry LCD Display User s Manual 19 LCD Displays OPD 212A 215A 217A Connecting to the Computer E Tum off
Download Pdf Manuals
Related Search