7600 Series
Contents
1. hold for approximately 3 seconds the Capture EDID button on the Transmitter front panel The Video LED will flash indicating the capture is in progress Note that any previously stored EDID information will be overwritten 6 When the Video LED remains off the capture is complete NOTE Performing EDID capture with an HDMI source connected to the 7600 will not result in damage nor will the EDID be successfully copied NOTE This procedure will erase any previously stored EDID information but not the fac tory default Page 8 Fiberlink 7600 Series User s Manual Fiberlink 7600 Series EDID Function EDID Functions cont Resetting back to factory defaults when EDID has been previously stored 1 Power off the 7600 Series transmitter 2 Disconnect any display from the 7600 HDMI input 3 Power on your 7600 Transmitter unit 4 Press and hold for approximately 3 seconds the Capture EDID button to erase stored EDID information 5 The Video LED should flash for confirmation Operating Tips Video Adjust Switch On the front panel of both the transmitter and the receiver is the VIDEO ADJ adjust Switch In some installations due to the length or quality of the HDMI cable being used it may be necessary to use the opposite phase of the pixel clock to clock the HDMI data into the trans mitter or into the monitor from the receiver If you experience color distortion on vertical edges of the video image use th2. ARRAN TY Warranty and Repairs Communications Specialties Inc CSI warrants that for a period of three years after purchase by the Buyer this product will be free from defects in material and workmanship under normal use and service A Return Material Authorization RMA number must be obtained from CSI before any equipment is returned by the Buyer All materials must be shipped to CSI at the expense and risk of the Buyer CSI s obligation under this warranty will be limited at its option to either the repair or replacement of defective units including free materials and labor In no event shall CSI be responsible for any incidental or consequential damages or loss of profits or goodwill CSI shall not be obligated to replace or repair equipment that has been damaged by fire war acts of God or similar causes or equipment that has been serviced by unauthorized personnel altered improperly installed or abused RMA numbers and repairs can be obtained from Communications Specialties Inc 125 Comac Street Ronkonkoma New York 11779 USA Tel 631 273 0404 Fax 631 273 1638 RMA numbers can also be obtained from our web site commspecial com Please have your serial number available Page 14 Fiberlink 7600 Series User s Manual Fiberlink 7600 Series Accessories and Related Products Broadcast the best results DVI I Computer Video to 3G HD SD SDI Scan Converter with Genlock Input and Fiber Optic Out
3. Communications Specialties Fiberlink 7600 User s Manual Distribute HDMI and stereo audio over one single mode or multimode fiber with no compression scaling conversions or frame dropping The 7600 Series is feature rich including our unique EDID function and Pixel Clock phase selections Fiberlink 7600 Series HDMI with Stereo Audio Transmission over one single mode or multimode fiber D 2 CS Communications Specialties Inc World Headquarters 125 Comac Street Ronkonkoma New York 11779 USA Tel 631 273 0404 Fax 631 273 1638 info commspecial com commspecial com Fiberlink 7600 Series Contents Contents Te EE 3 SH 3 Package Contents EE 3 eg ul lee e e EE 4 7600 Transmitter Specifications 0 ccc cece eee n eee e ene eeeenneeeeenes 4 HDMI Specification s sistre crsessriivresdisres sI Vor r tri IOA Er tehaw eth tubewdennaneds 4 Audio Be Le Ne 4 7600 Transmitter Optical Specifications 0 ccc ccc cece cece eee eee ene eeeenes 5 7601 Receiver HDMI Output 5 7601 Receiver Specifications EE 6 7600 General Specifications Ee 050s E REENEN 6 metalation MSHUCIONS eeren E hehe 7 PONDE E ON aata E ree ee EE E eee eee 8 ENID tee Ce EE EE 9 Cecile mll et ee recor ery ete eee mee re ree rr ee reer rere ee 9 Video AGIOS SWIC EE 9 Using Ke Battery EE 9 Alarm Switch Settings amp Options ccc ccc cece eee eee e eee eeeneeeeennes 10 ie Or E e CEET 11 Op ela FOIM CNS
4. FDA performance standard for laser products Title 21 Code of Federal Regulations Sub Chapter J 7601 Receiver HDMI Output Number of Outputs 1 Connector One Female HDMI type A with screw lock Spatial Resolutions 480i 480p 720p 1080i 1080p 1920x1200p 50 59 94 and 60 Hz vertical refresh Color Resolution 8 bits per pixel pixel for pixel sampling HDMI Embedded Audio 2 channels Color Space Support 8 Bit RGB or YCrCb HDCP Compliant with High bandwidth Digital Content Protection HDCP using HDMI standards Fiberlink 7600 Series User s Manual Page 5 Fiberlink 7600 Series Technical Specifications 7601 Receiver Specifications Fiber Optic Input Connector ST Wavelength 1100 1620 nm Minimum Input Sensitivity 17 dBm Maximum Input Power 0 dBm Link Budget with 7600 Transmitter 0 14 dB 7600 General Specifications LED Indicators Power Video Audio Alarm Card Version Only Box Version Dimensions 6 5w xX 1 15h x 8l in 165 W x 29 H x 203 L mm Weight 1 Ib 0 455 kg MTBF 32 000 hours Power 9 24 volts AC or DC 7600 5 3 watts 18 0 BTU Hr 7601 4 7 watts 16 0 BTU Hr Operating Temperature 10 C to 45 C Page 6 Fiberlink 7600 Series User s Manual Fiberlink 7600 Series Installation Instructions Installation Instructions The Fiberlink 7600 Series of fiber optic transmission system is ready for immediate use and does not require any special tools or equipment Howeve
5. cal connector with a lint free cloth moistened with alcohol whenever dust is suspected The status of the LEDs should provide the first clue as to the origin of any operational failure If these are off it usually means that the fiber is broken or has too much attenuation Next be certain that the input and output signal connections are correct An optical power meter such as the Fiberlink 6650 a visible light source such as the Fiberlink 6656 and a Three Wavelength Light Sources such as the Fiberlink 6652 or 6654 can greatly assist and expedite troubleshooting of fiber optic transmission systems and are recommended tools all installers should have available Finally although multimode and single mode devices may look the same they will not operate properly together Using the wrong device or fiber can easily add more attenuation than specified resulting in poor overall performance If after reviewing the above possibilities the system is still not operating please contact the Customer Service Department for further assistance If you suspect your problem is caused by the optics or the fiber optic cable and you have an optical power meter please take the appropriate measurements prior to contacting support Page 12 Fiberlink 7600 Series User s Manual Fiberlink 7600 Series Maintenance and Repairs Certifications Maintenance The Fiberlink 7600 Series has been manufactured using the latest semiconductor device
6. e opposite set ting of the switch on either the transmitter or the receiver or both Using 9 Volt Battery The 7600 transmitter unit can be temporarily powered using a 9V battery making it very easy to bring the transmitter to a ceiling mounted projector for EDID capture and storage If you receive unexpected display results you may be operating the 7600 using EDID informa tion that was stored during a previous installation Try clearing any stored EDID information Fiberlink 7600 Series User s Manual Page 9 Fiberlink 7600 Series Alarm Switch Settings amp Options Alarm Switch Settings amp Options The Rack Card version of this product has an additional red indicator LED that illuminates when an alarm condition exists The rack card unit also provides an output to drive a model 6020 Alarm Sensing Module which provides an audible tone and activates a set of contacts for external signaling purposes Alarm Switch Settings for the Transmitter and Receiver Card Switch Position Alarm Indication On Off Loss of HDMI Signal Enabled Disabled N A N A N A Typical Application Diagram Single Mode or og Ka Multimode Fiber Ny 59 HDMI Source 7600 Tx 7601Rx Page 10 Fiberlink 7600 Series User s Manual Fiberlink 7600 Series Indicator LEDs Indicator LEDs The Fiberlink 7600 Series has three integral indicator LEDs that are used to monitor the state of the unit Card versions have an additional Alar
7. hnical Specifications 7600 Transmitter Specifications Number of Inputs One HDMI up to 165MHz Pixel Clock Connector One female HDMI type A with screw lock Spatial Resolutions 480i 480p 720p 1080i 1080p 1920x1200p 50 59 94 and 60 Hz vertical refresh Color Resolutions 8 Bits per pixel pixel for pixel sampling HDMI Embedded Audio 2 channels EDID Ability to capture EDID from target monitor or internal default resolutions Color Space Support 8 Bit RGB or YCrCb HDMI Specifications Compliant with High bandwidth Digital Content Protection HDCP using HDMI standards HDMI Version Support v1 0 Fully supported v1 1 Fully supported v1 2 Fully supported v1 2a Fully supported v1 3 Fully supported v1 3a Fully supported v1 4 Supported v2 0 Supported 24 bit video max video clock of 165MHz and 2ch PCM audio are enforced via EDID protocol CEC Consumer Electronics Control is not supported ARC Audio Return Channel or HEC HDMI Ethernet Channel are not supported Audio Specifications Number of Audio Channels 2 unbalanced Page 4 Fiberlink 7600 Series User s Manual Fiberlink 7600 Series Technical Specifications Technical Specifications 7600 Transmitter Optical Specifications Emitter Type FP Laser Operating Wavelength 1310nm Optimal Optical Fibers SM 8 10 125 microns MM 50u or 62 5u Optical Connector ST Class Laser Product complies with
8. in the optical connector This device emits invisible infrared electromag netic radiation which can be harmful to human eyes The ra diation from this optical connector if viewed at close range with no fiber optic cable connected to the optical connector may be sufficient intensity to cause instantaneous dam age to the retina of the eye Direct viewing of this radiation should be avoided at all times Fiberlink 7600 Series User s Manual Page 7 Fiberlink 7600 Series Installation Instructions EDID Function Installation Instructions cont der Positive Power Connector e DC Input Polarity Negative 9 24 Volts AC or DC EDID Functions The Fiberlink 7600 Series of HDMI fiber optic transmission system has a unique EDID feature set that allows the capture and storage of EDID information or allows the genera tion of the EDID internally on the fly The procedures for implementing each feature are described below Generating EDID internally when no EDID has been captured The 7600 Transmitter comes programmed from the factory with generic EDID data If no external EDID data is captured this default EDID set will be used and presented to the HDMI source Capturing and storing EDID information 1 Power off your source and the 7600 Series transmitter Connect a display to the 7600 HDMI Input Power on the display BR U N Power on your 7600 Transmitter unit 5 Press and
9. m LED Transmitter and Receiver LEDs Status Definition On Indicates that correct power has been applied Off Indicates that no proper HDMI signal is present On Indicates that a proper HDMI signal is present Off Indicates no audio is present Blinking Indicates audio is present On Loss of video card version only Fiberlink 7600 Series User s Manual Page 11 Fiberlink 7600 Series Operating Pointers Troubleshooting Operating Pointers The 7600 Series is available in versions that operate with multimode MM 62 5u 50u and single mode SM optical fibers Be certain that the correct size fiber is being used for this particular transmitter receiver combination Also remember to check attenuation and bandwidth of the fiber optic cable The system will only operate properly if these specifications fall within the range of the system s loss budget Troubleshooting Multimode fiber optic cable contains an optical fiber with a light carrying core that is only 0025 inches 62 5 microns in diameter Single mode fiber optic cable has an even smaller core only 00032 to 0004 inches 8 10 microns This is smaller than a human hair Therefore any minute particles of dirt or dust can easily block the fiber from accepting or radiating light To prevent this from happening always use the provided dust caps when ever optical connectors are exposed to air It is also a good idea to gently clean the tip of an opti
10. put The all digital Scan Do HD converts DVI input at resolutions up to 1920 x 1080 to high definition 3G or HD or standard definition SD SDI output providing broadcast quality video images It supports all SMPTE 3G HD SDI output resolu tions up to 1080p and SD SDI resolutions NTSC and PAL making it the most versatile model in the Scan Do family The Scan Do HD is ideal for broadcasting on air or integrating into a professional video production system Features Converts DVI up to 1920x1200 to 3G HD SD SDI Advanced scaling algorithms and 10 bit processing provide exceptionally clean and accurate broadcast quality output Supports 3G HD SDI resolutions up to 1080p per SMPTE 424M SMPTE 292 and SD SDI resolutions per SMPTE 259 Genlock with full phasing control locks 3G HD SD SDI output to tri level sync or black burst Ethernet port enables control via your facilities LAN or via the Internet Includes fiber optic output SMPTE 297 2006 and two coaxial outputs SMPTE 424M 292 and 259 Image processing controls for brightness contrast saturation hue and sharpness variable flicker reduction Zoom amp Shrink horizontally and vertically while maintaining the aspect ratio or set each independently Precisely position your image horizontally and vertically Quickly store and recall your favorite configurations through the remote control ports Internal color bar generator 1 RU high includes mounting kit RoHS Complian
11. r an Optical Power Meter such as the Fiberlink 6650 can be useful in determining optical loss budgets during your system s design and system maintenance The following instructions describe the typical installation procedure 1 Connect the HDMI video source to the video input HDMI connector on the transmitter unit 2 Determine your EDID requirements and follow the procedures described in the EDID Function section of this manual 3 Connect the video output on the receiver unit to the HDMI monitor or load 4 Connect the fiber optic cable between the two Fiberlink units 5 Apply power to both the Fiberlink units For box versions using DC power connections refer to Figure 1 6 When power is applied the green POWER LED will light indicating the presence of operating power The VIDEO LED will give an indication as described on page 13 The green AUDIO LED will give an indication as stated on page 13 7 The system should now be operational Note The transmitter and receiver will each perform HDCP authentication with their source and load This will take several seconds to accomplish proper authentication Note The Rack Card version has an additional red LED for indicating the presence of an alarm condition loss of signal Refer to Indicator LED s and Alarm Switch Settings amp Options sections of this manual The transmitting element in the Fiberlink 7600 transmitter unit contains a solid state Laser Diode located
12. s and techniques that electronic technology has to offer They have been designed for long reliable and trouble free service and are not normally field repairable Should difficulty be encountered Communications Specialties maintains a complete service facility to render accurate timely and reliable service of all products The only maintenance that can be provided by the user is to ascertain that optical connectors are free of dust or dirt that could interfere with light transmission and that electrical connections are secure and accurate Please see the Troubleshooting section of this manual for additional information An optical power meter such as the Fiberlink 6650 a visible light source such as the Fiberlink 6656 and a Dual Wavelength Light Source such as the Fiberlink 6652 or 6654 can greatly assist and expedite troubleshooting of fiber optic transmission systems and are recommended tools all installers should have available All other questions or comments should be directed to our Customer Service Department It should be noted that many problems can easily be solved by a simple telephone call If you suspect your problem is caused by the optics or the fiber optic cable and you have an optical power meter please take the appropriate measurements prior to contacting support Certifications 4 FC G Fiberlink 7600 Series User s Manual Page 13 Fiberlink 7600 Series Warranty E i ta gt
13. t Learn more at scandohd tv Fiberlink 7600 Series User s Manual Page 15 Communications Specialties Fiberlink 7600 Fiberlink 7600 Series HDMI and Stereo Audio Transmission over one single mode or multimode fiber User s Manual IZ CSE seme World Headquarters 125 Comac Street Ronkonkoma New York 11779 USA Tel 631 273 0404 Fax 631 273 1638 info commspecial com commspecial com 2014 Communications Specialties Inc All Rights Reserved Scan Do Fiberlink and the starburst logo are registered trademarks of Communications Specialties Inc CSI and the triangle designs are trademarks of Communications Specialties Inc P N 129858 Rev B
14. uc oan cia wera seo se eo ee tece rede ret r EE teres Gueesese 12 Troubleshooting NEE 12 E en Ce er 13 Eleele E 13 Warranty and Repairs EE 14 Page 2 Fiberlink 7600 Series User s Manual Fiberlink 7600 Series Welcome Features Package Contents Welcome Thank you for purchasing Communications Specialties Inc s Fiberlink 7600 Series The 7600 Series is used to transmit pristine HDMI with stereo audio over a single fiber optic core Compatible with single mode or multimode fiber the 7600 is ideal for the most demanding of applications from distance learning to rental and staging The 7600 offers a unique EDID function that allows you to generate EDID internally or you can capture and permanently store EDID information Features e Supports HDMI resolutions up to 1920 x 1200 at 165 MHz pixel clock and HDTV resolutions of 480p 720p 1080i and 1080p e Unique 0 180 degree pixel clock selection to compensate for HDMI cable skew e Supports embedded stereo audio from the HDMI source e Uses no compression frame dropping or scaling for crystal clear signals e Only one fiber used no pixel skewing e Supports EDID from internal generation or capture and storage e Transmits signals over one single mode or multimode fiber optic core e ROHS Compliant Package Contents e One Fiberlink 7600 or 7601 e This User s Manual Fiberlink 7600 Series User s Manual Page 3 Fiberlink 7600 Series Technical Specifications Tec
Download Pdf Manuals
Related Search