E18SGGSMGW GSM Gateway Quick Guide
Contents
1. k SmartGuard E18SGGSMGW GSM Gateway Quick Guide 1 Safety Instructions Please read the following safety guidelines prior to installation e The SmartAccess GSM Gateway contains an integrated radio transceiver operating in GSM 850 900 1800 1900 MHz bands Do not install the system where it can interfere with other devices or cause any potential danger Do not mount the system next to medical equipment or medical devices Do not use the system in hazardous environments Do not expose the system to high humidity or in chemical environments The system must only be installed by a qualified engineer Any system repairs must be done only by qualified engineer The system must be powered by 10 24V DC The WEEE Waste Electrical and Electronic Equipment marking on this product or its documentation indicates that in the EU the product must not be disposed of together with household waste 2 Function The E18SGGSMGW is a device for transmitting data from alarm system to a monitoring station via e GSM audio channel e Telehone landline PSTN e GPRS network It can also send an SMS message to the user 3 Operation Description The E18SGGSMGW communicator acts as a gateway between the alarm system and monitoring station providing a dial tone and fully replacing the landline PSTN The communicator notifies the monitoring station E188GGSMGW ONLY and or the user by SMS message in case PSTN is unavailable has been cut off or2. disconnected by PSTN provider EL8SGGSMGW supports only outgoing calls DTMF number dialling mode in the alarm system must be enabled The E18SGGSMGW can detect temporary service suspension by the service provider for technical or billing reasons even if a dial tone is still present optional feature The E18SGGSMGW features several communication paths between an alarm system and monitoring station GSM audio channel PSTN using GSM audio channel as backup connection SMS messages to preset users PSTN using GSM audio channel as backup connection with data duplication to preset users via SMS GPRS network PSTN using GPRS network as backup connection Our 022 12 Please refer to section 6 Communication Modes for more details The E18SGGSMGW has 1 digital input normally open for sensor connection The open collector output allows you to connect and control 1 electronic appliance on receipt of an SMS text message from one of the pre programmed phone numbers This feature provides control of heating lighting gates blinds etc The SmartGuard Configuration Tool software is used to configure the system to operate in one of its communication modes providing data transmission either via SMS text message or via GPRS The device has to be connected to the computer using a USB cable Please refer to software s HELP section for more details CE 4 Electrical amp Mechanical Specifications Power supply 10 2
3. 0 O OO O00 e e L1 L2 L3 L4 RING TIP C1 DC COM N A N A Z1 OO OO To landline RING TIP AUX AUX PSTN ALARM SYSTEM 8 61 B2 1 Connect the circuit as indicated in Figure 13 connect telephone contacts of the Figure 14 alarm system RING TIP to RING TIP contacts of communicator Connect L3 L4 contacts to landline PSTN Power the unit from the alarm panel 12V and OV Set the jumpers on B1 B2 and SET pins See Figure 14 for correct jumper position AUN ene SET O O MODE O O PROG 7 SMS Commands ATTENTION In this user manual the underscore _ character represents one lt space gt character There must be no spaces or other characters at the beginning and at the end of the message XXXX 4 digit SMS password In order to configure and control E188GGSMGW system using SMS message send the text command to E18SGGSMGW SIM card phone number from one of the authorized phone numbers The structure of SMS message consists of 4 digit SMS password the default SMS password is 0000 four zeros the command and the parameters For some commands the parameters are not applied i e STATUS E18SGGSMGW notifies the user if a mistake was made in SMS command Command is not correct Status The SMS report indicating information on system input and output status H SMS Text XXXX STATUS Password The 4 digit SMS password intended for system configuration and control via SMS messages Manufactur
4. 4V 300 mA max Current used in standby mode 120mA max GSM modem frequency 850 900 1800 1900 MHz Supported protocols Contact ID 4 2 Maximum number of users to whom SMS messages 5 are delivered Number of low level negative digital inputs 1 Allowable input values Voltage 0 1 45V current 0 8 0 6mA Input type No normally open Number of outputs 1 Output circuit Open collector output Output is pulled to COM when turned on Maximum allowed output values Voltage 30V current 50 mA Dimensions 130 x 73 mm Operating temperature range 20 55 C Generated phone line voltage 18V Generated phone line current 25 mA Generated phone line impedance 600 Q Dial tone frequency of generated phone line 350 Hz only in EL8SGGSMGW 4 42 protocol operates in communication mode 1 5 and 9 ONLY via GSM audio channel 5 Components Connections Pin amp LED Functionality SIM CARD OOO dE 3 OOO L4 RING TIP 000 C1 DC COM OOO N A N A Z1 5 1 Component Functionality GSM MODEM GSM network 850 900 1800 1900 MHz modem SIM CARD SIM card slot holder ANT GSM antenna SMA type connector F1 Fuse model miniSsMDC 500mA USB Mini USB port 5 2 Connector Functional
5. TEM w Be Figure 8 1 Connect the circuit as indicated in Figure 7 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of the communicator 2 Power the unit from the alarm panel 12V and OV 3 Set the jumper on SET pins See Figure 8 for correct jumper position ene SET O O MODE O O PROG H 6 4 Data Transmission from Alarm System to Monitoring Station via PSTN using GSM Audio Channel as Backup Connection In this mode the communicator retransmits Contact ID and 4 2 data via landline PSTN sent from the alarm system to the monitoring station The communicator also monitors the voltage dial tone monitoring optional on the PSTN and in case the PSTN is unavailable disconnected or cut off voltage drops below 4V the system e Switches to backup connection GSM audio channel e notifies the monitoring station about PSTN failure e continues transmitting data to the monitoring station via GSM audio channel until the PSTN is restored NOTE Notification about PSTN loss restore if required has to be enabled for the communicator using the SmartGuard Configuration Tool Please refer to software s HELP section for more details Figure 9 OOO OOO O OO eec L1 L2 L3 L4 RING TIP C1 DC COM N A N A 21 OO OO To landline RING TIP AUX AUX PSTN ALARM SYSTEM B1 B2 Figure 10 1 Connect the circuit as indic
6. ated in Figure 9 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of communicator Connect L3 L4 contacts to landline PSTN Power the unit from the alarm panel 12V and OV Set the jumpers on B1 and B2 pins See Figure 10 for correct jumper position 7 AUN OO ISET O O MODE O O PROG 6 5 Data Transmission from Alarm System to Monitoring Station via PSTN using SMS Messages as Backup Connection In this mode the communicator retransmits Contact ID data via landline PSTN sent from the alarm system to monitoring station The communicator also monitors the voltage dial tone monitoring optional on the PSTN and in case the PSTN is unavailable disconnected or cut off voltage drops below 4V the system e sends an SMS report to the preset user s on PSTN failure e decodes data to user understandable text format and continues transmitting it to preset user s by SMS message until the PSTN is restored NOTE User phone number s must be set for the communicator using the SmartGuard Configuration Tool Please refer to software s HELP section for more details Figure 11 O00 O OO O00 O OO L1 L2 L3 L4 RING TIP C1 DC COM N A N A Z1 OO e To landline RING TIP AUX AUX PSTN ALARM SYSTEM 1 Connect the circuit as indicated in Figure 11 connect telephone contacts of the Bl B2 _ Figure 12 alarm system RING TIP t
7. d to default 8 2 SmartGuard Configuration Tool Software To configure the system please install the configuration software the SmartGuard Configuration Tool which can be downloaded from www rspl ie Before connecting USB cable to the computer please read the SmartGuard Configuration Tool user guide available in the HELP section of the software 8 3 Troubleshooting Problem Possible Reason GSM LED is off or not flashing e No external power supply e Circuit not properly connected e Blown fuse e No GSM network signal STATUS LED flashing several times per e SIM card not inserted improperly inserted second e PIN code enabled e SIM card inactive System does not send any SMS e SIM card credit limit exceeded messages e Incorrect SMS centre phone number e No GSM network signal e User phone number is not preset Received SMS message Incorrect e Incorrect syntax Format Extra lt space gt character is left in SMS message or Command is not correct 4 SmartGuard
8. efer to software s HELP section for more details ATTENTION You must set a monitoring station phone number in the alarm system s digital communicator one digit is enough Figure 5 OOO e e O00 OOO L1 L2 L3 L4 RING TIP C1 DC COM N AN A Z1 OO OO RING TIP AUX AUX ALARM SYSTEM 61 B2 Figure 6 1 Connect the circuit as indicated in Figure 5 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of the communicator 2 Power the unit from the alarm panel 12V and OV 3 Set the jumper on MODE pins See Figure 6 for correct jumper position O O SET eme MODE O O PROG 6 6 3 Data Transmission from Alarm System to Monitoring Station via GSM Audio Channel and SMS Messages to Preset User s In this mode the communicator retransmits Contact ID data sent from alarm system to the monitoring station via GSM audio channel In addition the data is duplicated and decoded data to user understandable text format and sent to preset user s by SMS message There is NO backup connection for this mode NOTE User phone number s must be set for the communicator using the SmartGuard Configuration Tool Please refer to software s HELP section for more details Figure 7 O00 8000 e e 6 OOO L1 L2 L3 L4 RING TIP C1 DC COM N A N A Z1 OO OO RING TIP AUX AUX ALARM SYS
9. er default SMS password is 0000 four zeros which is NECESSARY to change SMS Text H 0000 PSW XXXX Value XXXX new 4 digit password output on d This function switches the output ON H SMS Text XXXX ON Output OFF This function switches the output OFF H SMS Text XXXX OFF Output Pulse This function switches the output ON for a set period of time and switches the ON output back to OFF after the set period of time is over SMS Text H XXXX ON T Value T period of time in seconds range 1 9999 Output Pulse This function switches the output OFF for a set period of time and switches the OFF output back to ON after the set period of time is over SMS Text g XXXX_OFF_T Value T period of time in seconds range 1 9999 Telephone Line The delay period of time between telephone line failure and restore events If Failure Restore telephone line failure and restore events occur before the set delay period of time Delay is over the system will not send the SMS report SMS Text H XXXX TELDLY T Value T period of time in seconds range 1 250 10 8 Appendix 8 1 Restoring Default Parameters To restore the default parameters Disconnect the power supply Short circuit connect DEFAULT pins Power up E188GGSMGW for 7 seconds Disconnect the power supply Remove short circuit from DEFAULT pins Parameters restore
10. ity Labelling Description For configuration USB INFO O STATUS O GSM O Figure 1 L1 L4 Landline or PBX contacts according to backup mode RING RING contact TIP TIP contact C1 Output DC Positive power supply contact COM Negative power supply contact Common contact Z1 Input N A Not available 5 3 Pin Functionality Labelling Description DEFAULT For restoring factory default settings SET For enabling communication modes MODE For enabling communication modes B1 B2 For communication backup connection PROG Not used 5 4 LED Functionality Labelling Description INFO Mode indicator STATUS Device activity indicator GSM GSM network quality indicator 5 5 GSM Signal Strength Indication GSM signal strength is indicated by the GSM LED To ensure best network signal adjust the position of GSM antenna and find the strongest possible signal by observing the GSM LED indications GSM LED Indication GSM Signal Strength Off No connection Flashing every 3 seconds The connection is not reliable Flashing every 1 second Satisfactory Flashing several times per second Good On Excellent 5 6 Device Activity Indication STATUS LED Indication Meaning Off No power supply or some fault is present Flashing several times per second SIM card is not inserted inserted improperly On Device i
11. ivated Contact ID or 4 2 data transmission protocol and monitoring station phone number set with international code i e 00353XXXXXXXX Don not use the character 6 1 Data Transmission from Alarm System to Monitoring Station via GSM Audio Channel In this mode the communicator retransmits Contact ID or 4 2 data sent from alarm system to the monitoring station via the GSM audio channel There is NO backup connection for this mode NOTE No additional communicator configuration is required for this mode Figure 3 000 OOO O OO L1 L2 L3 L4 RING TIP C1 DC COM N A N A Z1 OO OO RING TIP AUX AUX ALARM SYSTEM 61 B2 OO OO Figure 4 1 Connect the circuit as indicated in Figure 3 above connect telephone contacts of sees the alarm system RING TIP to RING TIP contacts of the communicator 2 Power the unit from the alarm panel 12V and OV 3 No jumpers have to be set on any pins See Figure 4 for correct jumper position O O SET O O MODE O O PROG 6 2 Data Transmission from Alarm System to Preset User s by SMS In this mode the communicator retransmits Contact ID data sent from alarm system and decodes it to user understandable text format which is sent to preset user s by SMS message There is NO backup connection for this mode NOTE User phone number s must be set for the communicator using the SmartGuard Configuration Tool Please r
12. o RING TIP contacts of communicator Connect L3 L4 contacts to landline PSTN Power the unit from the alarm panel 12V and OV Set the jumpers on B1 B2 and MODE pins See Figure 12 for correct jumper position AUN O O SET em MODE O O PROG 6 6 Data Transmission from Alarm System to Monitoring Station via PSTN using GSM Audio Channel as Backup Connection and SMS Messages to Preset User s In this mode the communicator retransmits Contact ID data via landline PSTN sent from alarm system to monitoring station The communicator also monitors the voltage dial tone monitoring optional on the PSTN and in case the PSTN is unavailable disconnected or cut off voltage drops below 4V the system e switches to backup connection GSM audio channel notifies monitoring station about PSTN failure sends an SMS report to the preset user s on PSTN failure continues transmitting data to monitoring station via GSM audio channel until the PSTN is restored duplicates and decodes data to user understandable text format and sends it to preset user s by SMS message until the PSTN line is restored NOTE User phone number s must be set and notification about PSTN loss restore if required has to be enabled for the communicator using the SmartGuard Configuration Tool Please refer to software s HELP section for more details for more details Figure 13 O0
13. s operating and ready for use 5 7 Working Mode Indication I o D Indication Meaning off Device is in standby mode Flashing several times per second Device retransmits the data sent from alarm system to the monitoring station this indication is possible when device is operating in communication mode 1 On Device is decoding Contact ID data to user understandable text format 5 8 Wiring Diagram The COM connectors of E18SGGSMGW and Alarm System unit must be connected E18SGGSMGW Input Z1 is connected to PGM output of alarm system unit if PGM output is implemented as open collector E18SGGSMGW circuit or any other circuit and if it commutes with COM The E18SGGSMGW C1 output can be connected to the input of other zr electronic devices This connection allows you to control heating B BBB lighting gates blinds water pump etc 1 Make sure that SIM card PIN code is disabled PIN code can be disabled by putting SIM card into a mobile phone 2 Insert the SIM card into the holder 3 Terminate the Inputs and Output connections first before adding power 4 The system will start in less than a minute u d L 5 LED2 indicator should flash or will be ON indicating connection to 12V the GSM Network WOd Alarm system Figure 2 or other appliance Only in E18SGGSMGW 5 6 Communication Modes ATTENTION DTMF phone number dialling mode must be enabled on alarm system act
Download Pdf Manuals
Related Search