User`s manual DM111/DM111-2 Safe & Sound audio monitor
Contents
1. according to the intended usage of the product This product has been tested and found to comply with the FCC criteria The baby unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 20 cm 8 inches or more This Class B digital apparatus complies with Canadian requirement CAN ICES 3 B NMB 3 B For body worn operation this parent unit has been tested and meets the FCC RF exposure guidelines when used with the accessories supplied or designated for this product Use of other accessories may not ensure compliance with FCC RF exposure guidelines Industry Canada Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference including interference that may cause undesired operation The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met This product meets the applicable Industry Canada technical specifications RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment The baby unit should be installed and operated with a minimum distance of 20 cm 8 inches between the baby unit and all persons body Use of other accessories may not ensure compliance with FCC RF exposure guidelines This transmitter must not2. adjust the speaker volume e Press W to decrease the volume and A to increase the volume e f you continue to press wor A even the volume reaches the minimum or maximum setting the parent unit will sound once e When the parent unit is in mute the visual sound indicator will still indicate the sound detected from the baby unit Portable use of the parent unit optional Install the batteries on the parent unit Use only the AAA alkaline batteries not included e When the batteries are installed the parent unit turns on e The parent unit does not support recharging 1 Slide open the battery compartment cover 2 Flip the ribbon across the battery compartment 3 Insert two AAA alkaline batteries into the battery compartment on top of the ribbon 4 Slide the battery compartment cover until it clicks into place Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation To ensure safety of users the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander
3. supply Connect the parent unit to power supply or insert two new AAA alkaline batteries into the parent unit The parent unit turns on and establishes connection with the baby unit Why does the baby monitor produce a high pitched noise The units may be too close to each other Make sure the parent unit and the baby unit at least 1 meter 3 feet away from each other Why does the parent unit react too quickly to other sounds The baby unit also picks up other sounds than those of your baby Adjust the speaker volume on the parent unit 5 Product whose warranty quality stickers product serial number plates or electronic serial numbers have been removed altered or rendered illegible or 6 Product purchased used serviced or shipped for repair from outside the United States of America or Canada or used for commercial or institutional purposes including but not limited to Products used for rental purposes or 7 Product returned without a valid proof of purchase see item 2 on the next page or 8 Charges for installation or set up adjustment of customer controls and installation or repair of systems outside the unit How do you get warranty service To obtain warranty service in the United States of America visit www vtechphones com or call 1 800 595 9511 In Canada go to www vtechcanada com or call 1 800 267 7377 NOTE Before calling for service please review the users manual a check
4. when the parent unit is off Lights on in green when the parent unit is on and linked to the baby unit Flashes in green when there is no link between the baby unit and parent unit or when the parent unit is out of range from the baby unit Visual sound indicator The visual sound indicator shows the sound level detected from the baby unit It also shows the volume level during speaker volume setting Sound level detected from the baby unit is indepedent from the volume level set at the parent unit e Green lights indicate a moderate sound level detected from the baby unit or Level 1 to Level 3 of the speaker volume setting Red lights indicate a higher sound level detected from the baby unit or Level 4 to Level 5 of the speaker volume setting LOW BATTERY light e Flashes in red when the battery is low LOW BATTERY C Using your baby monitor Power on or off the baby unit To turn on the baby unit e Press and hold until the POWER light turns on To turn off the baby unit e Press and hold until the POWER light turns off Power on or off the parent unit To turn on the parent unit e Press and hold until the POWER LINK light turns on To turn off the parent unit e Press and hold unit the POWER LINK light turns off Speaker volume of the parent unit The speaker volume is preset to Level 3 on the parent unit You can adjust to your preferred sound level To
5. allow limitations on how long an implied warranty lasts so the above limitation may not apply to you In no event shall VTech be liable for any indirect special incidental consequential or similar damages including but not limited to lost profits or revenue inability to use the Product or other associated equipment the cost of substitute equipment and claims by third parties resulting from the use of this Product Some states provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Please retain your original sales receipt as proof of purchase Technical specifications Frequency Crystal controlled PLL synthesizer control Transmit Baby unit 1921 536 1928 448 MHz frequency Parent unit 1921 536 1928 448 MHz Channels 5 Nominal Maximum power allowed by FCC effective and IC Actual operating range may range vary according to environmental conditions at the time of use Power Baby unit adapter requirements Input 117V AC 60Hz Output 6V AC 300mA Parent unit adapter Input 100 120V AC 60Hz Output 6V DC 400mA Parent unit battery 2 X AAA alkaline batteries VTECH TELECOMMUNICATIONS LTD A member of THE VTECH GROUP OF COMPANIES Distributed in the U S A by VTech Communications Inc Beaverton Oregon 97008 Distributed in Canada by VTech Technologies Canada Ltd Richmond B C V6W 1L5 VTech is the regist
6. and metallic contacts 10 Use only the adapters included with this product Incorrect adapter polarity or voltage can seriously damage the product Baby unit power adapter Input 117V AC 60 Hz output 6V AC 300 mA Parent unit power adapter Input 100 120V AC 60 Hz output 6V DC 400 mA The power adapters are intended to be correctly oriented in a vertical or floor mount position The prongs are not designed to hold the plug in place if it is plugged into a ceiling under the table or cabinet outlet 12 Unplug this product from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning 13 Unplug the power cords before replacing the batteres 14 Do not cut off the adapters to replace them with other plugs as this causes a hazardous situation 15 Do not allow anything to rest on the power cords Do not install this product where the cords may be walked on or crimped 16 This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply in your home consult your dealer or local power company 17 Do not overload wall outlets or use an extension cord 18 Do not place this product on an unstable table shelf stand or other unstable surfaces r h Positioning the baby monitor Place the parent unit within the operating range of the baby unit We recommend the parent unit is at least 1 m
7. be co located or operating in conjunction with any other antenna or transmitter This equipment complies also with Industry Canada RSS 102 with respect to Canada s Health Code 6 for Exposure of Humans to RF Fields Standby mode The parent unit is on standby mode when e jt is not connected to the AC power supply and e there is no sound detected from the baby unit The standby time varies depending on usage and the battery life Full batteries can last up to 8 days Replace the batteries when e LOW BATTERY light flashes on the parent unit e The parent unit beeps twice every 30 seconds e The batteries are properly installed into the parent unit but the POWER LINK light on the parent unit is off Storage When you are not going to use the baby monitor for some time remove the batteries from the parent unit Store the parent unit the baby unit and the adapters in a cool and dry place General product care To clean and maintain this product e Avoid putting it near heating appliances and devices that generate electrical noise for example motors or fluorescent lamps DO NOT expose it to direct sunlight or moisture Avoid dropping the product or treating it roughly Clean with a soft cloth DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap DO NOT use cleaning spray or liquid cleaners Make sure the baby unit and parent unit are dry before you connect them to th
8. e power supply Operating range This product operates with the maximum power allowed by the Federal Communications Commission FCC Even so the baby unit and the parent unit can communicate over only a certain distance which can vary with the locations of the baby unit the parent unit the weather and the layout of your home When the parent unit is out of range it will beep three times every 10 seconds and enter searching mode To improve reception move closer to the baby unit but not less than 1 meter 3 feet Limited warranty What does this limited warranty cover The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase Consumer or you that the Product and all accessories provided in the sales package Product are free from defects in material and workmanship pursuant to the following terms and conditions when installed and used normally and in accordance with the Product operating instructions This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period Materially Defective Product During the limited warranty period VTech s authorized service representative will repair or replace at VTech s option without charge a Materially Defective Product If we
9. edes all other written or oral communications related to this Product VTech provides no other warranties for this Product The warranty exclusively describes all of VTech s responsibilities regarding the Product There are no other express warranties No one is authorized to make modifications to this limited warranty and you should not rely on any such modification Why don t hear a sound Why can t You may have muted the volume or set it to a lower level You may need to adjust the volume to a higher level hear my baby cry Why does the parent unit beep The baby units may be out of range Move the parent unit closer to the baby units but not less than 1 meter 3 feet When the parent unit is powered by batteries there is not sufficient power for the parent unit to perform normally Replace with two new AAA alkaline batteries Why does the parent unit LOW BATTERY light flash Why can t establish a connection Why is the connection lost every now and then Why are there sound interruptions The baby units may be out of range Move the parent unit closer to the baby units but not less than 1 meter 3 feet Other electronic products may cause interference with your baby monitor Try installing your baby monitor as far away from these electronic devices as possible FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements f
10. emoving parts of the product other than specified access doors may expose you to dangerous voltages or other risks Incorrect reassembling can cause electric shock when the product is subsequently used 23 You should test the sound reception every time you turn on the units or move one of the components 24 Periodically examine all components for damage 25 Be aware of possible loss of privacy while using public airwaves Conversations may be picked up by other nursery monitors cordless phones scanners etc 26 Children should be supervised to ensure that they do not play with the product 27 The product is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety SAVE THESE INSTRUCTIONS Cautions 1 Use and store the product at a temperature between 32 F and 104 F 2 Do not expose the product to extreme cold heat or direct sunlight Do not put the product close to a heating source 3 The batteries should not be exposed to excessive heat such as bright sunshine or fire 4 Make sure the baby unit and the adapter cord are always out of reach of the baby at least 1 meter 3 feet away from the baby or crib to avoid a possible strangulation hazard 5 Other electronic products may cause interference
11. ered trademark of VTech Holdings Limited Copyright 2013 for VTECH TELECOMMUNICATIONS LTD All rights reserved Printed in China Version 2 10 13 91 007297 020 100
12. eter 3 feet away from the baby unit to avoid audio feedback If you still experience audio feedback move the parent unit and the baby unit farther apart Operating range The operating range of the baby monitor is up to 300 meters 1000 feet outdoors or 50 meters 160 feet indoors The actual operating range may vary depending on the environmental conditions and other interferences such as walls doors and other obstructions Overview Baby unit overview 1 POWER light 2 amp On off Press and hold to turn on or off the baby unit 3 Microphone 4 Power jack 19 This product should not be placed in any area where proper ventilation is not provided Slots and openings in the back or bottom of this product are provided for ventilation To protect them from overheating these openings must not be blocked by placing the product on a soft surface such as a bed sofa or rug This product should never be placed near or over a radiator or heat register 20 Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit Never spill liquid of any kind on the product 21 To prevent fire or shock hazard do not expose this product to water or any type of moisture 22 To reduce the risk of electric shock do not disassemble this product but take it to an authorized service facility Opening or r
13. he problem experienced is caused by signal conditions network reliability or cable or antenna systems or 4 Product to the extent that the problem is caused by use with non VTech accessories or Frequently asked questions Below are the questions most frequently asked about the baby monitor If you cannot find the answer to your question contact customer service by visiting our website at www vtechphones com or calling 1 800 595 9511 In Canada go to www vtechcanada com or call 1 800 267 7377 Why does the baby monitor not respond normally Try the following in the order listed for common sure 1 Disconnect the power from the baby unit and the parent unit Remove the batteries from the parent unit Connect the baby unit to the power supply again The baby unit turns on Connect the parent unit to the power supply again or insert two new AAA alkaline batteries The parent unit turns on Wait for the parent unit to synchronize with the baby units Allow up to one minute for this to take place Why doesn t the POWER light on the baby unit turn on when switch on the units Perhaps the baby unit is not connected to the power supply Connect the baby unit to power supply The baby unit turns on Why doesn t the POWER LINK light on the parent unit turn on when switch on the units Perhaps the battery of the parent unit is empty and the parent unit is not connected to power
14. of the Product s controls and features may save you a Service call Except as provided by applicable law you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product s to the service location VTech will return repaired or replaced Product under this limited warranty Transportation delivery or handling charges are prepaid VTech assumes no risk for damage or loss of the Product in transit If the Product failure is not covered by this limited warranty or proof of purchase does not meet the terms of this limited warranty VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty What must you return with the Product to get warranty service 1 Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty and 2 Include a valid proof of purchase sales receipt identifying the Product purchased Product model and the date of purchase or receipt and 3 Provide your name complete and correct mailing address and telephone number Other limitations This warranty is the complete and exclusive agreement between you and VTech It supers
15. or a Class B digital device under Part 15 of the Federal Communications Commission FCC rules These requirements are intended to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help State Provincial Law Rights This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province Limitations Implied warranties including those of fitness for a particular purpose and merchantability an unwritten warranty that the Product is fit for ordinary use are limited to one year from the date of purchase Some states provinces do not
16. repair the Product we may use new or refurbished replacement parts If we choose to replace the Product we may replace it with a new or refurbished Product of the same or similar design We will retain defective parts modules or equipment Repair or replacement of the Product at VTech s option is your exclusive remedy VTech will return the repaired or replacement Products to you in working condition You should expect the repair or replacement to take approximately 30 days How long is the limited warranty period The limited warranty period for the Product extends for ONE 1 YEAR from the date of purchase If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty this limited warranty also applies to the repaired or replacement Product for a period of either a 90 days from the date the repaired or replacement Product is shipped to you or b the time remaining on the original one year warranty whichever is longer What is not covered by this limited warranty This limited warranty does not cover 1 Product that has been subjected to misuse accident shipping or other physical damage improper installation abnormal operation or handling neglect inundation fire water or other liquid intrusion or 2 Product that has been damaged due to repair alteration or modification by anyone other than an authorized service representative of VTech or 3 Product to the extent that t
17. t unit is not linked to the baby unit note the POWER LINK light on the parent unit will flash Move the parent unit closer to the baby unit but not less than 1 meter 3 feet Important safety instructions When using your equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury including the following 1 Follow all warnings and instructions marked on the product 2 Adult setup is required 3 This product is intended as an aid It is not a substitute for responsible and proper adult supervision and should not be used as such 4 This product is not intended for use as a medical monitor 5 Do not use this product near water For example do not use it next to a bath tub wash bowl kitchen sink laundry tub or swimming pool or in a wet basement or shower 6 CAUTION Use only alkaline batteries not included There may be a risk of explosion if a wrong type of battery is used for the parent unit Do not dispose of batteries in a fire They may explode Check with local codes for possible special disposal instructions 7 Do not open or mutilate the batteries Released electrolyte is corrosive and may cause burns or injury to the eyes or skin The electrolyte may be toxic if swallowed 8 Exercise care in handling the batteries in order not to create a short circuit with conductive materials 9 Observe proper polarity orientation between the batteries
18. that Pacemaker patients e Should keep wireless devices at least six inches from the pacemaker e Should NOT place wireless devices directly over the pacemaker such as in a breast pocket when it is turned ON WTR s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices Electromagnetic fields EMF This VTech product complies with all standards regarding electromagnetic fields EMF If handled properly and according to the instructions in this user s manual the product is safe to be used based on scientific evidence available today Parts checklist e Baby unit DM111 BU DM111 2 BU e Parent unit DM111 PU DM111 2 PU 1 for DM111 and 2 for DM111 2 e Power adapter for baby unit e Power adapter for parent unit 1 for DM111 and 2 for DM111 2 e User s manual e Use only the parent unit power adapter and the baby unit power adapter supplied with this product e The parent unit power adapter and baby unit power adapter are intended for a vertical or floor mount position The prongs are not designed to hold the plug in place if it is plugged into a ceiling under the table or cabinet outlet e Make sure the parent unit the baby unit and the power adapter cord are out of reach of children e Both the baby unit and the parent unit are on once connected to the power supply Parent unit light POWER LINK POWERILINK light C e Lights off
19. vtech User s manual DM111 DM111 2 Safe amp Sound audio monitor J P x a C o amp na vtech ER LII Congratulations on purchasing your new VTech product Before using this product please read Important safety instructions in this manual For support shopping and everything new at VTech visit our website at www vtechphones com In Canada please visit www vtechcanada com Register online to get an additional 3 month warranty Visit www vtechphones com Registration Register your product online for enhanced warranty support Product news Learn about the latest VTech products Connect the baby unit ap Power outlet not a controlled by a wall switch lt Power adapter Connect the parent unit a e Power adapter lt Power outlet not controlled by a wall switch Clas Ciase 2 0000000 0000000 00000 Before use You may test the baby monitor before initial use and at regular times thereafter To test your baby monitor 1 Place the parent unit and the baby unit in the same room to test the product 2 Press and hold on the baby unit until the POWER light turns off 3 Press and hold on the baby unit again until the POWER light turns on 4 Press and hold on the parent unit the POWER LINK light turns off 5 Press and hold on the parent unit again until the POWER LINK light turns on e fthe paren
20. with your audio monitor Try installing your audio monitor as far away from these electronic devices as possible wireless routers radios cellular telephones intercoms room monitors televisions personal computers kitchen appliances and cordless telephones Parent unit overview 00000000000 00000000000 200000000 6 pp 00009 9 ee 5 Visual sound indicator POWERLINK light LOW BATTERY light A Q N l V Volume down Press to decrease the speaker volume 5 W On off Press and hold to turn on or off the parent unit 6 Speaker Listen to sounds transmitted from the baby unit 7 A Volume up Press to increase the speaker volume 8 Belt clip 9 Battery compartment cover 10 Power jack Baby unit light POWER light e Lights off when the baby unit is off e Lights on in green when the baby unit is on 6 Never place the baby unit inside the baby s crib or playpen Never cover the baby unit or parent unit s with anything such as a towel or a blanket Precautions for users of implanted cardiac pacemakers Cardiac pacemakers applies only to digital cordless devices Wireless Technology Research LLC WTR an independent research entity led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers Supported by the U S Food and Drug Administra tion WTR recommends to physicians
Download Pdf Manuals
Related Search