User`s Manual
Contents
1. 4 Tap Reset Avoid Road Once you have set a destination you can look at the list of streets and determine if you need to mark one or more as unavailable If you mark a section as unavailable the Intellinav system will calculate a new route that avoids the section you marked NOTE You cannot avoid a road if you do not have a current destination To avoid roads in the route list 1 Tap Menu The main menu appears 2 Tap Destination The Destination Options screen appears 3 Tap Avoid Road The Avoid Road screen appears 4 Mark any segments that you do not want included a Tap on a route instruction to highlight it b Tap Avoid A do not enter symbol appears 5 When you have finished marking segments tap Nav Your route is recalculated the map appears and the guidance directions begin jenue S 1as5 240 eula ua ni n Stopovers Once you have set a destination you can add a stopover Adding a stopover does not cancel your original destination Once you reach your stopover you will be prompted to continue to the destination To create a stopover 1 Press Menu The main menu appears 2 Tap Destination The Destination Options screen appears 3 Tap Stopover The Set Destination screen appears 4 Set your stopover destination using any of the methods explained earlier in this section User s Manual To cancel a stopover 1 2 Tap Menu The main menu appears Tap Destination2. Mounting the Suction Cup 1 Press the suction cup firmly against the windshield 2 Press down the lever to fix the suction cup in place 3 Press in the circular buttons to unlock the arms 4 Adjust the angles of the arms to achieve the best viewing position Mounting the Cradle and GPS 1 Press the lever to lock or unlock the cradle 2 Insert the GPS unit bottom in first and then lock it using the lever on the top Charging the GPS unit 1 Prior to first use please use the wall charger to fully charge the unit for 4 6 hours until battery LED is green 2 In vehicle you may plug the car charger to provide continuous power On a full charge the unit can operate up to 5 hours User s Manual Starting Intellinav Press the POWER button The Intellinav screen appears Tap Navigate A warning screen appears Tap Agree after you have read and agreed to the warning The map view appears and you are ready to set your first destination Intellinay Mur wrk Crafideoe WARNING Du net enter dulu vr work the software s contuls while operating a vahide Itis dangerous lo du su Park vahide prior lu operating this software Netropa takes no responsibility for tre of any use that is inconsistent with this waming or the agreement end user Getting GPS Signal To use the Intellinav system to guide you to a destination the system s GPS antenna must receive GPS signals GPS signals can be obstructed by ceilin
3. The Destination Options screen appears Tap Clear Route A confirmation message appears asking if you want to continue to your next destination Tap Yes The map appears and navigation continues Setting an Itinerary The Itinerary feature allows you to set multiple destinations You can add remove or re order destinations according to your needs To set the Itinerary 1 Tap Menu The main menu appears 2 Tap Itinerary The Itinerary screen appears 3 Tap Add to add new destinations from Favorites Recent or POI list or enter a new address as destination 4 Tap Del to remove a destination from the Itinerary 5 Tap Go to start navigating from the first item on the Itinerary To Re order the Itinerary 1 Tap Move Up or Move Down Add Move Bes Cis Using Shortcuts The shortcut feature provides you quick access to some of the most important destinations while you re on the road including e Home e AIM e Gas e Hospital e Parking e Restaurant e Tourist Information By tapping any of the POI categories you will see a list of the nearest POls sorted by distance jenuey S 125 240 AeUIJ 33U Managing Your Favorites List You can edit the destinations you add to your favorites list to give them descriptive names You can also remove destinations from your favorites list To manage your favorites list 1 Tap Menu The main menu appears
4. or by selecting the city first If you use Street First and too many records match you will be asked to use City First To enter an intersection as a destination using Street First 1 Tap Menu The main menu appears User s Manual Tap Destination The Set Destination screen appears Tap Intersection The Input Method screen appears If you need to change the region or State a Tap Change State The Enter State Name screen appears b Tap the Letters to enter the name of the region or tap the name of the region c Tap OK when you have selected the region You return to the Inout Method screen Tap Street First The Enter Street Name screen appears Tap the Letters to enter the name of the street Tap OK when you have selected the street The Enter 2nd Street Name screen appears Tap the Letters to enter the name of the second street Tap OK when you have selected the street The Select Address screen appears 8 Select the intersection that matches the location you want to go to and tap Nav The map appears and the guidance directions begin To enter an intersection as a destination using City First 1 Tap Menu The main menu appears 2 Tap Destination The Set Destination screen appears 3 Tap Intersection The Input Method screen appears 4 If you need to change the region a Tap Change State The Enter State Name screen appears b Tap the Letters to enter the n
5. 2 Tap Favorites The Favorites screen appears Add To Favorites m m e To edit a favorite a Tap on the favorite you want to edit b Tap Edit The Edit Favorites screen appears c Enter a descriptive name for this favorite d Tap OK when you are done User s Manual To delete a destination from your favorites list a Tap on the favorite you want to delete b Tap Del The favorite is removed from the list c ap OK to close the Favorites screen Setting Your Options You can set many different options to customize the Intellinav system and make it work your way These options include Display Options J Route Options Options Speed Alert paad Alet aa 2 ltocakzation n 5 e Localization Display Options The display options give you control over the appearance of the map You can change the following e Orientation e Guidance e Day Night e POI Icons e Color viis a e 3D View There are two orientation settings Heading turns the map as you drive so that you are always moving toward the top ofthe screen North keeps the map oriented with North at the top of the map like a traditional paper map There are two guidance settings which control whether or not the maneuver detail screen appears when you near your next maneuver If you use the auto setting the maneuver detail screen appears The day night setting controls the background of the screen
6. Alphabetical The Enter POI Name screen appears The four methods of selecting a specific point of interest include two for nearby POls and two for all POls in a region Kad Pants of Interest ha b Tap the Letters to enter the name of the POI Tap OK when you have selected the POI The POI Select screen appears displaying the address of the POI To select a nearby POI as a destination 1 Tap Menu The main menu appears c Tap Nav The map appears and the guidance directions begin 2 Tap Destination The Set Destination screen wed Pere s ku Pe aeta 3 Tap POI The Points of ee Interest screen appears maika Convention Center To rtst Info Ta POT Name User s Manual Q POI Select 1210 5 DAC DLVD Tet 7147236 ann aar To select a nearby POI by distance a Tap By Distance The POI List screen appears listing the closest POls first b Tap the POI that you want to go to and tap Nav You may need to scroll down the list by tapping the scroll bar The map appears and the guidance directions begin B POIL List e To select from all POls in a region 1 Tap Menu The main menu appears 2 Tap Destination The Set Destination screen appears 3 Tap POI The Points of Interest screen appears 4 Tap a Category Usually a subcategory screen appears NOTE If you chose Restaurant tap the Letters to enter a type of restaurant If you chose Hotel there is no su
7. If you choose auto the Intellinav system will automatically switch to a darker version of your color scheme soon after sunset to reduce the glare in the vehicle You can also choose to use either the day or night setting at all times There are three options for displaying POI icons If you choose default the most commonly displayed categories of POI icons will appear on the map at zoom levels of 1000 ft and closer If you choose off no POI icons are displayed If you choose custom you can choose which categories of POI icons you want displayed The color settings control the background color of the map You can choose from four different colors jenue S 1as 240 AeUIJ 33U The 3D view settings control your view of the map Off shows you the map in traditional 2D mode High Medium and Low show you a 3D version of the map with a different angle for each value If you use any of the 3D settings you will not be able to tap on a location to view location information To set your display settings 1 Tap Menu The Menu button and then Settings 2 Tap Display Options The Display Options screen appears 3 Tap your Orientation preference Heading or North 4 Tap your Guidance preference Auto or Manual 5 Tap your Day Night preference Auto Night or Day 6 Tap your POI Icons preference Default Off or Custom When you tap Custom the POI Options screen appears User s Manual a Tap on the categories yo
8. b Tap the city that you want to go to and tap Nav You may need to scroll down the list by tapping the scroll bar The map appears and the guidance directions begin To select from all City Centers in a region 1 Tap Menu The main menu appears 2 Tap Destination The Set Destination screen appears 3 Tap City Center The City Center screen appears To select a city center in a region or State User s Manual a Tap List All The Enter City Name screen appears b Tap the Letters to enter the name of the city Tap OK when you have selected the city The City Center screen appears c Tap Nav The map appears and the guidance directions begin Detours Avoid Roads and Stopovers The Detour feature will allow you to bypass a certain portion of the route starting at your present position while avoid road allows you to bypass the entire road Stopovers are stops you add to a trip to make prior to reaching your destination Detour NOTE you cannot create a detour if you do not have a current destination To set a detour 1 Tap Menu The main menu appears 2 Tap Destination The Destination Options screen appears 3 Tap Detour The Detour screen appears 4 Select from three distance options to bypass A new route is calculated automatically To clear a detour 1 Tap Menu The main menu appears 2 Tap Destination The Destination Options screen appears 3 Tap Detour The Detour screen appears
9. next street the direction of your next turn and the distance to the turn At the bottom of the map you see the estimate of how much time remains before arriving at your destination the remaining distance to your destination and your current speed On the upper left is an arrow indicating the direction and the type of maneuver ahead as well as the remaining distance to the next maneuver CASSIDY STREAT 14 S S AN MHAI HN Y ys irmimmi 43 mph Panning the Map You can pan the map by tapping and dragging the map To return to the regular map view press the X button Panning Map Click om W to Rehim Baer jenuey S 1as 240 AUI 334 Route List Location Information manual You can also get additional information about If you have set a destination you can view a list of the You can find location information about any point on the the current location including latitude and longitude maneuvers that make up your route map by pressing firmly on the map for one second A screen appears giving you the opportunity to set the POI Information To view the route list location as the Start or the Destination and save the To view information about a POI on the map tap on the ae PR location to your Favorites list or view information icon on the map The POIS screen will appear OMAR ADI R YT lsr BIS P o mi t From the Information screen you have several options EE TANU SANTA AMA esit ight Map
10. of any motor vehicle from placing displaying jenuey S 125 240 AeUIJ 33U affixing and or applying any objects such as suction mounts on the windshields Other dashboard or friction mounting options should be used Intellinav does not take any responsibility for any fines penalties or damages that may be incurred as a result of disregarding this notice California Vehicle Code Section 26708 a Minnesota Statutes 2005 Section 169 71 User s Manual System Specifications The Intellinav One has the following specifications SIRF Star III GPS chipset SAMSUNG 53C2410 ARM920T 266Mhz CPU 64 MB NAND flash 64 MB SDRAM onboard 3 6 inch 16 7M Colors TFT LCD with touch panel SD memory slot for map data MP3 or photos Build in 1 watt speaker GPS antenna with external antenna connector USB 1 1 connector WinCE NET 4 2 OS Kernel Up to 5 hours Battery Life Rechargeable Internal Lithium polymer battery 1700 mA MP3 Player Photo Viewer Host Start 1 sec average Warm Start 38 sec average Cold Start 42 sec average 210 g Weight Dimensions 120x89x33 mm jenuey S 125 240 AUI 334 Netropa Corporation 1499 Huntington Dr Suite 305 South Pasadena CA 91030 Office 626 403 2866 http www intellinav com
11. want 2 Tap to zoom out the image display Orientation To change the image orientation 1 Tap ligi to rotate the image 90 180 270 or 360 clockwise Stereo Slide Show You have the option to view images in a slide show much like viewing a presentation Images are adjusted to fit the entire display area and are shown in a 3 second interval To enable the Slide Show mode 1 In Thumbnail or Full Screen mode tap ag Slide Show 2 Tap the touch screen to stop the slide show and return to the previous viewing mode jenuey s s 240 AeLUIJjIJUJ Safety and Regulation FCC Declaration of Conformity Tested to comply with FCC standards for home or office use This eguipment complies with Part 15 of the U S Federal Communications Commission FCC Rules Operation of this device may not cause harmful interference and this device must accept any interference received including interference that may cause undesired operation If this occurs the user is encouraged to try and correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and external receiver e Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected e Consult the dealer or an experienced radio or television technician for help CE Marking This equipment complies with the requirement f
12. Copyright 2006 Netropa Corp htto www intellinav com All rights reserved Part number IN KIGO1 Intelli Drive with Confidence Intellinav One User s Manual I 5 NORINE SS I 10 W SAN BERNARDINO FWY 4 08PM 00 06 60mi 73mph Intellinav MENU Table of Contents Getting Started es ms mn m e ved ee 8 vanne ee eed 1 2 Basie OOo OA an een m et ee 4 Mounting the Intellinav System 5 Starting Ihtellihav i x20 e cuave samm sed ame oe m 6 Getting OPS Signal 2 ea onu a Hides pa sed 6 GU se ett ERN 6 GPS IMGMMalOn 2 4564 saiad esse ages m 6 Entering Data on the Intellinav System 7 Moving Through the Screens 7 Resetting the Intellinav System 7 Working with the Maps uavan dans dmeeda isekas 8 MD VIS ae orel a ee oe 8 Maneuver Detail 00 eee 8 Panning th Map 22s6 s2esedoades eaten buss 8 Kolde E his Sere ee eee et nos Ss 7 Location Information 0 9 Polintomatom exesaansatvassa ds samad 10 Planning Your Route J4na andud ees eee weed 11 Setting a Single Destination 11 Using an Address as a Destination 11 Using an Intersection as a Destination 13 Using a Point of Interest POI as a Destination 15 Using a Favorite Destination as a Destination 17 Using a Recent Destination as a Destination 17 Using a City Center as a Destination 18 De
13. OCCIICAUIONS i4eiciensauheuteddvuees 48 jenuey S 125 240 AUI 334 Getting Started Congratulations on your purchase of the Intellinav system Your Intellinav system can guide you to the destination of your choice using signals from Global Positioning Satellites GPS orbiting the earth There are 24 GPS satellites orbiting the earth A GPS device can calculate your position on the earth if it can receive signals from at least three of these satellites When it receives at least four signals a GPS device can also calculate your altitude height above sea level You can start using the Intellinav system simply by mounting the holder on the car s windshield plug in the charger and press the power button on the top of the system For your safety and the safety of others please do not operate the system while driving It is dangerous to do so When you want to enter an address or change a setting please pull over and park the car in a safe area first You should always pay full attention to the road and use the system only as an aid by taking only glances at a time and listening to the voice prompts An inexperienced driver should NOT use the system User s Manual Basic Operation SD Card Slot Power Button External Antenna Connector Earphone Jack USB Port DC In LED LCD Panel Speaker rear Volume Reset bottom Main Menu jenuey S 125 240 AUI 334 Mounting the Intellinav System
14. UI 334 TERMS AND CONDITIONS License Grant You may use one copy of the enclosed Software and Data on a single computer with a single CPU and a Windows CE device You may not network the Software and or Data or otherwise use it on more than one computer or mobile computer at the same time You may use Software and Data to provide you with navigation position and route guidance information You may make one copy of the Software and Data solely for backup or archival purposes You may not copy or share or make any other use of the backup copy except use to reinstall your active copy if it becomes erased corrupted or disabled The backup copy must include all copyright information contained in the original You may not copy the written materials accompanying the Software Personal Use Only You agree to use this Data together with the Intellinav system for the solely personal non commercial purposes for which you were licensed and not for service bureau time sharing or other similar purposes Accordingly but subject to the restrictions set forth in the following paragraphs you may copy this Data only as necessary for your personal use to i view it and ii save it provided that you do not remove any copyright notices that appear and do not modify the Data in any way You User s Manual agree not to otherwise reproduce copy modify decompile disassemble or reverse engineer any portion of this Data and may not transfer or d
15. ame of the region or tap the name of the region c Tap OK when you have selected the region You return to the Inout Method screen 5 Tap City First The Enter City Name screen appears Tap the Letters to enter the name of the city Tap OK when you have selected the city The Enter Street screen appears Tap the Letters to enter the name of the street Tap OK when you have selected the street The Enter 2nd Street Name screen appears Tap the Letters to enter the name of the second street Tap OK when you have selected the street The Select Address screen appears Select the intersection that matches the location you want to go to and tap Nav The map appears and the guidance directions begin jenuey s s 240 AeLUIJjIJUJ Using a Point of Interest POI as a 4 Tap a Category Usually a subcategory screen Destination SPRER There are many points of interest that you can select as a destination Generally you choose a category and then choose one of four methods of selecting the specific point of interest Sometimes you must first select a subcategory such as Museum within the category of Attractions before you can choose a selection method NOTE If you choose Restaurant tap the letters to enter a type of restaurant If you choose Hotel there is no subcategory screen Go to the next step 5 Tap a Subcategory The POI Options screen appears To select a nearby POI from an alphabetical list a Tap
16. ary and gently wipe the touch screen User s Manual When unattended do not leave the device in the vehicle that is subjected to direct sunlight for an extensive period of time The overheating of unit and or battery may cause malfunctioning of the device Keep the device away from excessive moisture and extreme temperatures When connecting the device to the car adaptor please make sure the input voltage of the adaptor is identical with the car voltage This device uses a rechargeable lithium ion battery To reduce the risk of fire or burns do not disassemble crush puncture short external contacts or dispose of in fire or water In some instances during playback a few bright or dark flecks may appear on the TFT LCD screen This is a normal phenomenon in active matrix display technology and not a malfunction Important Information When using Intellinav One please make sure you are operating the device in compliance with all local state and federal regulations It is the sole responsibility of the driver of the vehicle to operate the vehicle in a safe manner and not become distracted by Intellinav User should not operate the controls of Intellinav while you are driving Netropa shall not be liable for any accident Warning When used in a vehicle it is the sole responsibility of the driver of the Intellinav system to place and secure the device where it will not interfere with the vehicle s operation controls and or
17. av e Fav e Show User s Manual from your current location or the location you set as a starting point to the destination Fav adds the destination to your Favorites list Your Favorites list is a list of locations that you can add destinations to You can also enter a name for a destination and delete destinations from the list Show displays the location on the panning map without calculating a route You can also use it to manually set a starting point Using an Address as a Destination There are two ways to enter the address by selecting the street first or by selecting the city first If you use Street First and too many records match you will be asked to use City First NOTE You will be prompted for the street name first then the house number To Enter an Address as a Destination Using Street First 1 Tap Menu The main menu appears Tap Destination The Set Destination screen appears Tap Address The Input Method screen appears If you need to change the region a Tap Change State The Enter State Name screen appears b Tap the Letters to enter the name of the region or State or tap the name in the list c Tap OK when you have selected the region or State You will return to the Input Method screen Tap Street First The Enter Street Name screen appears Tap the Letters to enter the name of the street Tap OK when you have selected the street The Enter House Numbe
18. bcategory screen Go to the next step 5 Tap a Subcategory The POI Options screen appears To select a POI from an alphabetical list 1 Tap List All The Enter POI Name screen appears 2 Tap the Letters to enter the name of the POI Tap OK when you have selected the POI The POI Select screen appears jenuey S 1as 240 AUI 334 3 Tap Nav The map appears and the guidance To Select a Favorite as a Destination To select a destination from your list of recent To do this you select a City Center as a destination directions begin destinations 1 Tap Menu The main menu appears As with selecting a Point of Interest there are several To select a POI by city 2 Tap Destination The Set Destination screen 1 Tap Menu The main menu appears methods of selecting a city center two for nearby city appears centers and one for all city centers in a region 1 Tap By City The Enter City Name screen appears 2 Tap Destination The Set Destination screen 3 Tap Favorites The Favorites screen appears appears To select a nearby City Center as a destination 2 Tap the Letters to enter the name of the city and tap OK The Enter POI Name screen appears 4 Tap on the favorite you want to use as a 3 Tap Recent The Recent screen appears 1 Tap Menu The main menu appears destination and tap Nav The map appears and 3 Tap the Letters to enter the name of the POI and the guidance directions begin 4 Tap on the recent destination you want to g
19. e Set Stopover with an existing route Set Start Location J ASE lt ti set start Location b 1 Tap Menu The Main Menu appears A e Set Destination 2 Tap Destination The Destination Option screen e Save This Location appears i Block Info 3 Tap Route List e Information EDE AADA ca J ee 34 147252N 4 Tapping an item on the list and then tapping Show Setting the location as a Longitude 110 144264W will display the detail directions for that turn starting point is useful if you are trying to find the distance between two locations Setting the location as your destination is a quick way to set a destination Saving the location adds the location to your Favorites list you ll learn more about Favorites later in this User s Manual jenuey S 125 240 AUI 334 Planning Your Route You can seta destination with the Intellinav system many different ways Once you have set a destination you can add a detour or a stopover The Intellinav system also offers an Itinerary feature where you can enter up to 100 destinations and use the Itinerary screen to re order addresses as you like Setting a Single Destination You can set your destination the following ways Set Destination F Address z Intersection pr C GE Point of Interest POI kd Favorites Recent City Center When you have found your destination you have several options 3 Select Address e N
20. ed normal To correct this perform a GPS reset This will update the GPS database which contains information about the GPS satellites that the unit needs to function in navigation mode jenue S 1as 240 AUI 334 To Reset the GPS 1 Close the navigation program if it is currently running by tapping on Menu in the map display and then Exit in the navigation Menu screen 2 Tap System on the Main Menu panel 3 Tap System Info on the System panel 4 Tap GPS Reset and then Yes to confirm 5 The GPS Reset process will take about a minute to complete User s Manual MP3 Playback you can use a computer to load MP3 onto an SD card and then load that sd card into the SD card slot located at the side of the unit To open the MP3 Player 1 Tap MP3 on the Main Menu panel The MP3 player appears To open MP3 files for playback 1 Tap the Folder button to open the file browser The program will automatically scan the device SD MMC card for supported digital files Only sub directories containing compatible music files will be displayed 2 Search for the file s you want to play by tapping a Y to scroll through all available files 3 Tap a file to start playback of the selected file a When the file is located in the root directory tap the file for playback b When the file is located inside a sub directory tap the sub directory icon then tap a file for playback 4 Tap Up One Level button to
21. eturn to the map To set a fixed speed alert a Tap Fixed b Enter the speed you want to use as a maximum speed c Tap OK after reading the warning message You return to the map Localization The localization options give you control over the settings affected by your location including e Language e lime Zone e Daylight Savings Time e Units There are six language settings When you change the language all of the screen names and controls will be in the selected language There are six time zone settings for all areas of the United States There are two daylight savings options to determine whether or not daylight savings time is currently in effect at your location There are two settings for units which determine how the distance to your location is expressed You can choose between Mi miles or KM kilometers To set your localization settings 1 Tao Menu Menu screen appears 2 Tap Settings Settings screen appears Tap Localization The Localization screen appears Tap your Language preference English French Spanish Chinese Korean or Japanese Tap your Time Zone preference Eastern Central Mountain Pacific Alaska or Hawaii Tap your Daylight Saving preference DST or Standard Tap your Units preference Mi or KM When you have finished choosing your options tap OK eNUefJA s s 240 AUI 334 System Settings Screen Calibration When you first tu
22. gs trees and nearby tall buildings Signals can also be obstructed by the roof of your vehicle For best results position your Intellinav system where it has a clear view of the sky The very first time turning on the system may take as long as 15 minutes to obtain a valid GPS fix Once the first GPS fix is obtained thereafter it should normally take no more than 30 seconds to 1 minute to obtain a valid GPS fix Car Cursor The status of the GPS signal is represented in the car cursor color Green 4 or more satellites Yellow 3 satellites Red less than 3 satellites Gray no satellite at all Only when the car cursor is green will you be receive accurate GPS tracking and navigation GPS Information To view the GPS information eee e 1 Tap Menu The Main UTC 2005 07 05 19 18 30 Menu appears CAL ANY ALA 33 199562N 117 370834W or 2 Tap GPS Information cr 32 mph The GPS Information E screen appears To close the GPS Information screen 1 Tap the Back Arrow in the upper right corner enUefJA sasn BUG neula Entering Data on the Intellinav System The Intellinav system doesn t have a keyboard Instead you tap the screen to enter data When you are entering data a screen containing the Letters of the alphabet appears a City Name e As you tap the buttons on the keyboard the list at the top of the screen scrolls to show the next item that matches the Letters you ve tapped If you need
23. he hot keys backlight 1 Tap the Hot keys backlight on when pressed check box 2 Tap 4 b to set the hot keys backlight s auto oft function Options include backlight off after 5 10 15 and 20 seconds 3 Tap amp to apply the changes made To enable the hot keys backlight when power is plugged in 1 Tap the Hot keys backlight on when AC in check box 2 Tap to apply the changes made jenuey S 125 240 AeUIJ 33U Backlight To set the screen backlight level 1 Tap to adjust the screen backlight level 2 Tap amp to apply the changes made Backlight nant O O TT Hever To set the screen backlight auto off function 1 Tap 4 F under the Battery and AC Power settings a Options for Battery includes Never after 10 or 15 seconds and for AC Power includes Never after 1 2 or 3 minutes 2 Tap amp to apply the changes made User s Manual Date Time To set the date l Date Time 1 Tap on Date 2 Tap on 4 bto set the Year Month and Day 3 Tap amp to apply the changes made To setthe Time 1 Tap on Time 2 Tap on 4 bto set the Hour and minute 3 Select AM or PM 4 Select 24 Hours to show 24 hour clock 5 Tap to apply the changes made To set the Time Zone 1 Tap on Time Zone 2 Tap on 4 bto select the Time Zone that is application to you 3 Tap amp to apply the changes made Note The Automatically adjust clock for daylight saving cha
24. istribute it in any form for any purpose except to the extent permitted by mandatory laws Restrictions Except where you have been specifically licensed to do so by LICENSEE and without limiting the preceding paragraph you may not a use this Data with any products systems or applications installed or otherwise connected to or in communication with vehicles capable of vehicle navigation positioning dispatch real time route guidance fleet management or similar applications or b with or in communication with any positioning devices or any mobile or wireless connected electronic or computer devices including without limitation cellular phones palmtop and handheld computers pagers and personal digital assistants or PDAs Warning The Data may contain inaccurate or incomplete information due to the passage of time changing circumstances sources used and the nature of collecting comprehensive geographic data any of which may lead to incorrect results No Warranty This Data is provided to you as is and you agree to use it at your own risk LICENSEE and its licensors and their licensors and suppliers make no guarantee representation or warranty of any kind express or implied arising by law or otherwise including but not limited to content quality accuracy completeness effectiveness reliability fitness for a particular purpose usefulness use or results to be obtained from this Data or that the Data or ser
25. l retailer purchaser It is not transferable All exchanged parts and products replaced under this warranty will become property of the Company This limited warranty only extends to product purchased from the Company and the authorized dealers and resellers This warranty does not apply if the product or part thereof which in the opinion of the Company has been damaged or rendered defective through alteration improper installation mishandling misuse neglect accident or by removal or defacement of the factory serial number bar code label s The opinion of the Company with respect to this matter shall be final THE EXTEND OF THE COMPANY S LIABLITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE RETAIL PURCHASER FOR THE PRODUCT THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES OR LIABILITIES ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM THE DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED WHATSOEVER No person or representative is authorized to assume fo
26. n User s Manual 2 To disable the Repeat mode tap the fade out Repeat icon 3 Tapping Random icon will automatically disable the Repeat mode Playback Volume To adjust the playback volume you can use either the MP3 volume control slider or the volume control hardware buttons To control the playback volume 1 Hold and drag the slider of the volume level bar This will only affect the volume of the track playback 2 Press the volume buttons This will also adjust the sound level for the device s system sounds Photo Viewer With the Intellinav system you can keep images of your favorite moments as mobile as you are by using the Photo Viewer You can use a computer to load pictures onto an sd card and then load that sd card into the SD card slot located at the side of the unit The program features e Support for JPEG and BMP 1 4 8 and 24 bit files e Auto scanning of supported files in the device s SD MMC card e Three viewing modes Thumbnail Full Screen and Slide Show e Album support based on sub directory contents o Each sub directory containing compatible image files is treated as an individual album For a more organized file search it is advisable to sort image files into sub directories based on something such as a particular event or a certain period To illustrate a sub directory containing pictures from your daughter s birthday can be named Cassie s 10th Birthday or Ma
27. nges will be displayed under the Time Zone setting menu if the daylight saving system is adopted System Info You may have to perform a reset if the device freezes i e device no longer responds to the buttons on the screen A soft reset allows your device to get a fresh start similar to rebooting a computer This will restart your device and adjust memory allocation All records and entries are retained after a soft reset GPS settings are also retained Factory Reset To perform a soft reset 1 Hold the device securely and then press the soft reset button O lt on the bottom of your device To load the factory default setting If you still encounter problems even after soft resetting the device loading the factory default settings may correct the problems These default settings have been selected to optimize your device s performance 1 Tap System on the Main Menu panel 2 Tap System Info in the System panel 3 Tap Factory Reset and then Yes to confirm 4 After the Factory Reset reconfigure your device s user preferences GPS Reset In the following circumstances the TTFF Time To First Fix values of your device may be longer than usual e After a long period of inactivity e Ifthe current GPS fix position is more than 500km or more than 12 hours apart from the previous position o This is due to the nature of the GPS algorithm and rotational velocity between the satellites and planet Earth and is deem
28. o to 2 Tap Destination The Set Destination screen tap OK The POI Select screen appears 4 Tao Nav The map appears and the guidance directions begin and tap Nav The map appears and the guidance appears directions begin 3 Tap City Center The City Center screen appears Using a Favorite Destination as a Destination Favorite destinations are locations you add to a list on Using a Recent Destination as a the Intellinav system You can add locations to your Destination Favorites list as you set a destination from the POIS screen and from the Location Information screen You Recent destinations are locations you have navigated to Using a City Center as a Destination To select from an alphabetical list can then easily select one of these locations as a recently You can easily select one of these locations as a destination destination Managing your recent destinations list is Sometimes you may want to use the Intellinav system to a Tap Alphabetical The Enter City Name covered later in this section get to a city but not to a specific location within the city screen appears User s Manual enUeJA s s 240 eula b Tap the Letters to enter the name of the city Tap OK when you have selected the city The City Center screen appears c Tap Nav The map appears and the guidance directions begin To select by distance a Tap By Distance The City List screen appears listing the closest city centers first
29. or CE marking when used in a residential commercial or light industrial environment User s Manual Canada Radio interference regulation class B compliance This class B digital apparatus meets all compliances of the Canadian Interference Causing Equipment Regulations Software License Agreement The mapping and navigation software Software and map data Data is provided for your personal internal use only and not for resale It is protected by copyright and is subject to the following terms and conditions which are agreed to by you on the one hand and Netropa LICENSEE If you do not agree to the terms of this agreement promptly exit the program Your rights under this License will terminate automatically without notice if you fail to comply with any term s of the License 2006 NAVTEQ All rights reserved The Data for areas of Canada includes information taken with permission from Canadian authorities including Her Majesty the Queen in Right of Canada Queen s Printer for Ontario Canada Post Corporation GeoBase NAVTEQ holds a non exclusive license from the United States Postal Service to publish and sell ZIP 4 information United States Postal Service 2006 Prices are not established controlled or approved by the United States Postal Service The following trademarks and registrations are owned by the USPS United States Postal Service USPS and ZIP 4 jenuey S 125 240 A
30. r the Company any liability other than expressed herein in connection with the sale of this product Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state jenuey s s 240 AeLUIJjIJUJ Caring for your device Please use only the power adapter included in the box and connects to the voltage reguirement indicated on the rear panel of the product Use of any other types of chargers will result in malfunction of the device and void all warranties Do not use and or charge this device near water or moisture Never touch or handle any power sources with wet hands To prevent fire or electric shock never expose the device to any types of liquid Do not block any ventilation openings or use in extreme weather conditions such as dusty sandy wet or humid When in use please install in accordance with the user manual Do not attempt to service the unit Any modification tempering and or change to the device not expressly approved by Netropa Corp or its authorized parities will void all warranties in entirety Do not attempt to clean the device with the power on Use a clean moistened lint free cloth to wipe the exterior of the device Use water or eyeglass cleaner if necess
31. r screen appears Tap the Numbers or Letters A D to enter the house number Tap OK The Select Address screen appears 8 Select the address that matches the location you want to go to and tap Nav The map appears and the guidance directions begin To Enter an Address as a Destination Using City First 1 Tap Menu The main menu appears 2 Tap Destination The Set Destination screen appears 3 Tap Address The Inout Method screen appears 4 If you need to change the region or State a Tao Change State The Enter State Name screen appears b Tap the Letters to enter the name of the region or State or tap the name in the list c Tap OK when you have selected the region You will return to the Inout Method screen 5 Tap City First The Enter City Name screen appears 6 Tap the Letters to enter the name of the City Tap jenuey s s 240 neula OK when you have selected the City The Enter Street Name screen appears 7 Tap the Letters to enter the name of the street Tap OK when you have selected the street The Enter House Number screen appears 8 Tap the Numbers or Letters A D to enter the house number Tap OK The Select Address screen appears 9 Select the address that matches the location you want to go to and tap Nav The map appears and the guidance directions begin Using an Intersection as a Destination There are two ways to enter the intersection by selecting the street first
32. r which this NAVTEQ Data was User s Manual provided and each copy of the NAVTEO Data delivered or otherwise furnished shall be marked and embedded as appropriate with the following Notice of Use and shall be treated in accordance with such Notice Notice of Use Contractor Manufacturer Supplier Name NAVTEQ Contractor Manufacturer Supplier Address 222 Merchandise Mart Plaza Suite 900 Chicago Illinois 60654 This Data is a commercial item as defined in FAR 2 101 and is subject to the End User Terms under which this NAVTEA Data was provided 2006 NAVTEQ All rights reserved If the Contracting Officer federal government agency or any federal official refuses to use the legend provided herein the Contracting Officer federal government agency or any federal official must notify NAVTEQ prior to seeking additional or alternative rights in the NAVTEQ Data Limited Warranty 1 year parts and labor Netropa the Company warrants to the original retail purchaser of this product that should this product or any part thereof under normal use and condition be proven defective in material or workmanship within one year from the date of original purchase such defects will be repaired or replaced with new or reconditioned parts without charge for the parts and repair labor provided that transportation charges are prepaid The sales receipt is your proof of the date of purchase This warranty only extends to you the origina
33. rect product thereof except in compliance with and with all licenses and approvals required under applicable export laws rules and regulations Entire Agreement These terms and conditions constitute the entire jenuey s s 240 AeLUIJjIJUJ agreement between LICENSEE and its licensors including their licensors and suppliers and you pertaining to the subject matter hereof and supersedes in their entirety any and all written or oral agreements previously existing between us with respect to such subject matter Governing Law The above terms and conditions shall be governed by the laws of the State of Illinois insert Netherlands where European NAVTEA Data is used without giving effect to i its conflict of laws provisions or ii the United Nations Convention for Contracts for the International Sale of Goods which is explicitly excluded You agree to submit to the jurisdiction of Illinois insert The Netherlands where European NAVTEA Data is used for any and all disputes claims and actions arising from or in connection with the Data provided to you hereunder Government End Users If the NAVTEO Data is being acquired by or on behalf of the United States government or any other entity seeking or applying rights similar to those customarily claimed by the United States government the NAVTEQ Data is a commercial item as that term is defined at 48 C F R FAR 2 101 is licensed in accordance with the End User Terms unde
34. return to the root directory 5 The selected file will automatically be played Files in the same directory will also be played provided the repeat function is disabled Playback Controls The icons in the MP3 player let you control the playback mode To control file playback Keys Descriptions Il Tap to pause or resume playback a Tap to stop playback 4 Tap to skip backward to the previous track If the current file is the first track in the list the last track will be played dd Tap to skip forward to the next available track If the current file is the last track in the list then the first track will be played jenuey S 1as5 240 AeUIJ 33U Shuffle Mode Each directory containing supported music files is considered a playlist You can choose to shuffle the playback sequence to play files in random order To rearrange the playback seguence 1 To enable the Shuffle mode tap Random An enabled Shuffle mode is indicated by the word Random on the playback display and a fade out Random icon 2 To disable the Shuffle mode tap the fade out Random icon Repeat Mode The repeat mode lets you play the current track in a loop The same track will be played over and over until you disable the Repeat mode To enable or disable the Repeat mode 1 To enable the Repeat mode tap E Repeat An enabled Repeat mode is indicated by the word Repeat in the playback display and a fade out Repeat ico
35. rn on the Intellinav system you will be asked to calibrate the system This process ensures that when you tapthe screen the item tapped is activated You can also recalibrate by tapping on System Sys Info and Calibration To calibrate the screen 1 From the Main Menu tap on System and then Sys Info 2 Tap the center of the black dot as it moves around the screen User s Manual User Preferences You can adjust the settings of your device to suit the way you work Adjusting certain settings such as those for system volume power LED and backlight may increase your standby time To access the System panel 1 Tap System on the Main Menu panel Tap to set the volume level for system sounds and enable tapping sound Tap to view the battery power level and enable the hot keys backlight Tap to set the touch screen backlight level and enable its auto off function Tap to change the system date time and time zone settings Tap to set the language option for the system menus and voice prompts Tap to displays your device s OS Version GPS F W and SW Code Version Options for factory reset GPS reset and calibration Volume To set the system sound level 1 Tap to adjust the volume level 2 Tap amp to apply the changes made Volume TT a To enable tap sounds 1 Tap the Enable sounds for taps check box 2 Tap amp to apply the changes made Power To enable t
36. safety devices The driver should mount the device where it does not obstruct the driver s view of the road or cause any damage or personal injury in the event of an accident The mounting accessory included in the package is not warranted against collision damage or the consequences thereof Do not mount where driver s field of vision is blocked Do not mount over airbag panels or in the field of airbag deployment Do not place unsecured on the vehicle dash Netropa shall not be liable for any environmental conditions that may influence the operation of your Intellinav One An inexperience driver shall not use the Intellinav system The Global Positioning System GPS is operated by the United States government which is solely responsible for the accuracy and availability of GPS The system is subject to changes that could affect accuracy and availability of your device The utmost preparation is given to this manual With constant improvements and upgrades Netropa cannot guarantee for all contents to be most current and entirely up to date Information contain in this guide is subject to change without notice and we shall not be liable for technical and or editorial errors of this guide Map data The manufacturer supplier of the data is NAVTEQ North America LLC 222 Merchandise Mart Plaza Suite 900 Chicago Illinois 60654 NOTICE TO DRIVERS IN CALIFORNIA AND MINNESOTA State law from these states prohibits drivers
37. to enter numbers tap the 1 2 3 button and the numeric keyboard appears kv Street Name e User s Manual Moving Through the Screens The Intellinav system shows you one screen ata time Each time you tap a button a new screen appears If you want to return to go to the previous screen tap the in the upper right corner of the screen If you want to go back to the map view directly tap the button on the upper left corner of the screen Resetting the Intellinav System You should never have to reset the Intellinav System under normal circumstances However in the event that a problem cannot be corrected you may reset the Intellinav System by pressing the Reset button on the bottom of the unit using a pen or paper clip Working with the Map The Intellinav system gives you many ways of looking at the map You can see your current position view any of the turns on a route and the map to view other areas You can zoom in and out and find information about specific locations Map View The map view on the Intellinav system shows your current location At the bottom of the map is a scale indicating your current zoom level On the upper right is the compass On the center right and left are zoom in and out buttons respectively aL ea SISA NIRS ANY Maneuver Detail If you have set a destination the map displays additional information As you navigate to a destination the top of the map displays the name of the
38. tours Avoid Roads and Stopovers 20 setting an ltinelably lt scnd ehee odav 22 User s Manual Using Shortcuts z 24 nad sata go ohem onm weds 22 Managing Your Favoriteslist 23 Seting T U OPIO ausa an esta ab grier 24 Di piy OPONE a sk rre E EAER 24 ROUIG OPUONS sares r Antia vea ENTAR 26 Speed Al Maata se sas see 27 oelda aa aaa 28 System SEHINGS e ne pe aE EEE sei des msal 29 Screen Calibratiomn e 29 User Preferences si 29 VOUE 4 3 ne perce de ees eh Vn eo 30 LOMI e eee ee eles eh a eden 30 Backlight 4445 44 5 aha eee Depa ieee GEA 31 Date TME sees bccn eur em ed a 31 System see ssess austusest t 32 Factory Reset po 64 sandy ae wonennaelsnt vs 32 OPS Reset speek Hes GSO oe eee oa OSES 32 MPS Playback mata ces ceed eee cea beer ats 34 Playback Controls ones ole ame same m 34 Shuffle Mode 4 04 ua idea eves hue 35 Repeat Mode cise enaasassedad veevaba avama 35 Playback V IME po koos bac aeeeseceoured cs 35 Photo VIEWER La sons eea sde ceri ee teseeeeeuE 36 Full Screen Mode 0 37 Magnification 4 37 een ke va 37 ASSO sessisiteredk renit wea heoeeeen 38 Safety and Regulation 0 39 Software License Agreement 40 Limited AA saseta ateena tea 44 Caring for your device 0 eee ene 45 Important Information 0 0 0 eee eee 46 system S
39. u want displayed The categories to be displayed are highlighted b You can use Select All and Clear All to quickly highlight or clear categories c When you have highlighted the categories you want displayed tap OK You return to the Display Options screen 7 Tap your Color preference Yellow Grey White or Fuchsia 8 Tap your 3D View preference 2D High Medium or Low 9 When you have finished choosing your options tap OK Route Options The route options give you control over the navigation of your trip You can change the following e Method e Ferries e Toll Roads e Carpool e Turns There are four method settings Quickest calculates the route that should take the least amount of time Major calculates a route that uses major roads whenever possible Shortest calculates the route that is shortest in distance Local calculates a route that uses local roads whenever possible The ferries setting indicates whether ferries should be included when your route is calculated If you include ferries the route will take you to the ferry terminal but the total time for the route does not take into account the ferry schedule or time spent on the ferry The toll roads setting indicates whether you want to include or exclude toll roads when your route is calculated If you include toll roads those roads will be used if appropriate for the method you selected The carpool setting indicates whether or not
40. ver will be uninterrupted or error free Disclaimer of Warranty LICENSEE AND ITS LICENSORS INCLUDING THEIR LICENSORS AND SUPPLIERS DISCLAIM ANY WARRANTIES EXPRESS OR IMPLIED OF QUALITY PERFORMANCE MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT Some States Territories and Countries do not allow certain warranty exclusions so to that extent the above exclusion may not apply to you Disclaimer of Liability LICENSEE AND ITS LICENSORS INCLUDING THEIR LICENSORS AND SUPPLIERS SHALL NOT BE LIABLE TO YOU IN RESPECT OF ANY CLAIM DEMAND OR ACTION IRRESPECTIVE OF THE NATURE OF THE CAUSE OF THE CLAIM DEMAND OR ACTION ALLEGING ANY LOSS INJURY OR DAMAGES DIRECT OR INDIRECT WHICH MAY RESULT FROM THE USE OR POSSESSION OF THE INFORMATION OR FOR ANY LOSS OF PROFIT REVENUE CONTRACTS OR SAVINGS OR ANY OTHER DIRECT INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF YOUR USE OF OR INABILITY TO USE THIS INFORMATION ANY DEFECT IN THE INFORMATION OR THE BREACH OF THESE TERMS OR CONDITIONS WHETHER IN AN ACTION IN CONTRACT OR TORT OR BASED ON A WARRANTY EVEN IF LICENSEE OR ITS LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Some States Territories and Countries do not allow certain liability exclusions or damages limitations so to that extent the above may not apply to you Export Control You agree not to export from anywhere any part of the Data provided to you or any di
41. y 11 to June 24 for a sub directory consisting of pictures taken during that period Note The performance of the Photo Viewer may be affected by the size of the image files To open Photo Viewer 1 Tap Photo on the Main Menu panel 2 The program will automatically scan the device s SD MMC card for supported image files Image files will be displayed as thumbnails only sub directories containing compatible files will be displayed 3 Tap 4 Y to scroll through all available files When a thumbnail is selected a red border appears around it jenue S 1as 240 AUI 334 Full Screen Mode In Full Screen mode image files can be viewed ina larger scale You can also change its orientation angle To view images in Full Screen mode 1 Search for the file you want to view 2 Tap 4 to scroll through all available files 3 Tap Up One Level to return to the device s root directory 4 Open the file in Full Screen mode a When the file is located in the root directory tap the file b When the file is located inside a sub directory tap the sub directory icon then tap the file you want to view 5 Tap 4 to display the previous available image 6 Tap b to display the next available image User s Manual Magnification To change the image magnification level 1 Tap to zoom into the center of the image a When in a zoomed in state you can hold and drag the image to pan it in any direction you
42. you want to include carpool or high occupancy vehicle HOV restrictions in the calculation of your route The turns setting indicates whether or not you want to make more or less turns To set your route settings 1 Tap Menu The main menu appears 2 Tap Route Options The Route Options screen appears 3 Tap your Method preference Quickest Major Shortest or Local 4 Tap your Ferries preference Include or Exclude 5 Tap your Toll Roads preference Include or Exclude 6 Tap your Carpool preference Include or Exclude 7 Tap your Turns preference Reduced or Normal jenuey sasn BUG neula 8 When you have finished choosing your options tap OK Speed Alert You can use the speed alert feature to warn you if your vehicle is exceeding the speed limit There are two speed alert options auto speed alert and fixed speed alert Auto speed alert uses the type of road to determine the probable speed limit Fixed speed alert lets you enter a speed and will warn you if that speed is exceeded Auto speed alert is based on road class and may not necessarily reflect the actual speed limit Please use this feature only as a reference To set the speed alert 1 Tap Menu and then Settings 2 Tap Speed Alert The Speed Alert screen appears User s Manual Speed Alert F ei ki a A To set auto speed alert a Tap Auto A warning appears b Tap OK to close the warning c Tap OK You r
Download Pdf Manuals
Related Search