Peristaltic Dosage Pumps - Aquarius Technologies Pty Ltd
Contents
1. Aquarius Technologies Pty Ltd ON OFF Control AP_PERI Model AP PERIVAR AP_PERIS_VAR_ Rated Pressure 350kPa 350kPa Motor Speed 10RPM_ 30RPM_ Motor Speed 10RPM 30RPM Glass Filled Polypropylene 6 x 4 mm PVC tubing Viton sleeve on PVC 15 mm BSP male thread Tri Roller polypropylene Plug on appliance lead Snap On Snap Off Specifications subject to change and development These pumps are designed to meet dosage on demand requirements using APL logic 8 where the duty cycle is varied to the system demand Installation a The pump is intended for wall mounting using the bracket supplied which allows for snap on or snap off for ease of servicing The bracket forms a simple template for drill holes position Electrical Installation When wall mounted as indicated opposite the pump is weatherproof to IP56 standards The applicance connection lead fitted with an Australian 3 pin plug allows for easy disconnection for servicing of the unit The unit requires a 220 240 Vac 50 Hz power supply Tubing Connections Items marked 5 and 6 on the oppposite page are the suction tubing and drum weight for the chemical tank and are fitted to the left side pump inlet Push tubing full up unto spigot and screw the tube nuts firmly with the fingers no Variable Dosage Option spanners are required nor should be used The clear tubing allows for vision It is easy to tune the dosing rate in our variable perist2. PUMP MOTOR 30RPM Service Kits AP_PERI_O_KIT AP PERI OVERHAUL KIT AP_PERI_S_KIT AP PERI SERVICE KIT Maximum service interval 2 years Included in this Kit are the following Maximum service interval 12 months Included in this Kit are the following e AP_TUBE4824 Number 8 e AP_INJECT Number 1 e AP _ROLLBLOCK Number 3 e AP_DWEIGHT Number 6 e AP_TUBE4824 Number 8 e AP_INJECT Number 1 e TUBESUCTION Number 5 2 metres e TUBEDISCHARGE Number 2 2 metres e AP PERI_LID Number 7 e TUBESUCTION Number 5 2 metres e TUBEDISCHARGE Number 2 2 metres Warnings Chemicals in use as part of the treatment program may be hazardous Please refer to the full Material Safety Data Sheets MSDS provided by your chemical supplier and ensure all personnel involved are aware of the handling and safety procedures Please read and understand all safety warnings on chemical containers before servicing any dosing equipment Wear as a minimum safety goggles and gloves when servicing the dosing equipment Do not mix concentrated acids and oxidising agents as explosion and or toxic and lethal gas may be evolved and or fire result Keep all chemical containers sealed and free from contamination Regular Inspections and Maintenance For optimum results and continued accuracy the complete operation of the dosing system should be verified at least on a monthly service basis Injection non return valves and pumps sh
3. altic pumps of pump suction and positive dosage Remove the nylon screw plug from the bottom of the pump By using a Items marked 1 and 2 on page opposite fine screwdriver insert it into the pot as shown above Turn clockwise are the black pump discharge tubing to increase and anti clockwise to decrease Adjust till the required dosage and injection fitting Fit as suction tube rate is achieved Our pump control allows for a variability of 10 100 of above but to the right side pump outlet full dosage during a 1 min period Fit Teflon tape to the 15 mm BSP threads and fit into the intended dosage line to the system Aquarius Technologies Pty Ltd bit Number Description Aquarius Part Number 1 Discharge Line Injector and Non Retum Valve 15 mm BSP male APINECTO 2 Discharge Tubing Black 6 x 4 mm PVC tubing TUBEDISCHARGE a rei Roller Block with 3 Rollers Axles assembled AP ROLLBLOCK 4 Electrical Lead and plug in adaptor Australian 3 pin plug ___LEADPUMPINP 5 Suction Tubing Clear 6 4 mm PVG tubing TUBESUCTION 6 Suction Tube Drum Weight for Chemical Tank AP COI 8 Norprene Squeeze Tube and Tube nuts pp ruBEa O 9 ar 1 LPH pump complete with tubing injectors and power lead AP PERI 1 complete ea ar 3 LPH pump complete with tubing injectors and power lead AP PERIS complete 10 Motor 220 250 Vac 16 Watt 10 RPM for 1LPH pump PUMP_MOTOR_10RPM 10a _ motor 220 250 Vac 16 Watt 30 RPM for 3 LPH pump
4. ould be cleaned and checked at least annually Sodium Hypochlorite being highly alkaline may lead to scale formation on its dose injector and this may require acid cleaning on a frequent basis On the peristaltic dose pumps the squeeze tubes and roller bloc should be checked at least annually and should be replaced ever 12 24 months More regular maintenance may be required for the larger 3 0 l hr pumps due to increased pumping rates Chemical suction and discharge tubes should be inspected monthly Other Sales Bulletins from Aquarius KPI Intelligent Water Treatment Controllers Cooling Water Treatment Controllers Swimming Pool Disinfection Controllers Trade Waste or Effluent Controllers Potable Water Disinfection Controllers AquaGuard 2 Water Management Software for remote control interface from a PC Aquarius Technologies Pty Ltd Distributed By TECHNOLOGIES PTY LTD Fax WATER QUALITY CONTROL Phone 617 3274 4750 Web www aquariustech com au Unit 1 23 Richland Ave Coopers Plains Q 4108 P O Box 71 Coopers Plains Q 4108 Australia 617 3274 4736 This document is subjected to Aquarius Technologies Pty Ltd trading terms and conditions which can be obtained from the following link htto www aquariustech com au terms html
Download Pdf Manuals
Related Search