USER`S MANUAL DT2205 / DT039-50
Contents
1. illuminates that the system is clearing data from printer Red Solid This illuminates printer head open cutter error This illuminates a printing error such as head open paper Red Flash empty paper jam or memory error etc 4 2 Regular Button Function 1 Feed labels When the printer is ready press the button to feed one label to the beginning of next label 2 Pause the printing job When the printer is printing press the button to pause a printing job When the printer is paused the LED will be green blinking Press the button again to continue the printing job 4 3 Power on Utilities There are six power on utilities to set up and test printer hardware These utilities are activated by pressing FEED button then turning on the printer power simultaneously and release the button at different color of LED Please follow the steps below for different power on utilities 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED indicates with different color for different functions Power on utilities The LED color will be changed as following pattern Amber Amber Green Green Amber Red Amber Solid green ee a a 1 1 Gap black mark sensor calibration black mark sensor calibration Release Release 1 2 Gap black mark sensor calibration Release Self test and enter dump mode 4 Set black mark sensor as media Release sensor and calib2. One power cord One auto switching power supply One USB interface cable If any parts are missing please contact the Customer Service Department of your purchased reseller or distributor 2 2 Printer Overview 2 2 1 Front View DT2205 model DT039 50 model cover open lever MicroSD card socket Media view window LED indicator Feed button Paper exit chute LCD display Option for DT2205 model Recommended MicroSD card specification The DOS FAT file system is supported for the SD card Folders files stored in the SD card should be in the 8 3 filename format 2 2 2 Interior View 2 DT039 50 model pm pm rm pm o mg 2 DT2205 model Top cover Media holder Media guide Printhead Gap sensor receiver Gap sensor transmitter Platen roller Black mark sensor oO FP WN gt Media holder lock switch 2 2 3 Rear View DT2205 model DT039 50 model Power switch Power jack socket USB interface RS 232C interface Option for DT039 50 mode Fan fold paper entrance chute Ethernet interface Option for DT2205 model USB host Factory option for DT039 50 mode Note The interface picture here is for reference only Please refer to the product specification for the interfaces availability 3 Setup 3 1 Setting Up the Printer 1 Place the printer on a flat secure surface 2 Make sure the
3. mm 65 04 m 60 6D 2C 38 35 2E 38 34 28 6D GLE 6D OD 43 4C 53 OD OA 42 41 RCODE 144 43 AF 44 46 20 31 34 34 2C 49 39 31 34 39 2C 22 33 39 22 2C 31 2z0 1 0 2 6 32 38 20 31 26 30 26 32 2C 36 CETTTASBT 22 35 3T 31 31 34 33 38 54 7 PRINT 1 22 OD BA 52 49 20 31 1 26 31 Note 1 Dump mode requires 2 wide paper width 2 Turn off on the power to resume printer for normal printing 3 Press FEED button to back to the previous menu 4 3 3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults Printer initialization is activated by the following procedures 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns green after 5 amber blinks Any green will do during the 5 blinks B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks 3 red amber 5 blinks gt solid green Printer configuration will be restore to defaults as below after initialization Default setting Speed 127 mm sec 5 ips 203DPI Dmy SSS Label Width 2 50 8 mm Label Height 4 101 6 mm Gap Setting 0 12 3 0 mm 21 Reference Point 0 0 upper left corner eege Serial Port Settings 9600 bps none parity 8 data bits 1 stop bit Off Off 850 001 No Offset ear Mode IP Address D
4. as installed paper in the labeling software or program Labels may be stuck inside the printer Remove the stuck label mechanism near the sensor area Top cover is not closed properly Close the top cover completely and make sure the right side and left side levers are latched properly Wrong power supply is connected with Check if 24V DC output is supplied by the power supply printer Check if supply is loaded correctly Reload the supply Peery rink GN Check if dust or adhesives are Clean the print head accumulated on the print head Check if print density is set properly Aae the print density and print speed Check print head test pattern if head Run printer self test and check the print head test pattern if there is dot missing element is damaged in the pattern 31 5 3 LCD display Option for DT2205 model This section lists the LCD display messages that you may encounter when operating the printer Also it provides solutions Messages Possible Cause Recovery Procedure No Paper Paper Jam Out of Mem Take Label Cutter Error The printer top cover is open Running out of label The label is installed incorrectly Gap black mark sensor is not calibrated Gap black mark sensor is not set properly Make sure label size is set properly Labels may be stuck inside the printer mechanism The space of FLASH DRAM or MicroSD card is full Peel function is enabled Waiting user
5. width height Gap size vertical gap offset Sensor sensitivity ETTE EEE EEE EE ET FILE LIST DRAM FILE FILE S FLASH FILE FILE S File management information PHYSICAL DRAM AVAILABLE DRAM PHYSICAL FLASH AVAILABLE FLASH END OF FILE LIST KHHHHHHHHHHMHHHHHHMHHMHHHHMHHMHMMHMMHMHMEMMMHMM KBYTES KBYTES FREE KBYTES KBYTES FREE B Dump mode Printer will enter dump mode after printing printer configuration In the dump mode all characters will be printed in 2 columns as following The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters It allows users or engineers to verify and debug the program 26 ASCII Data Dinant 38 54 54 as 82 zu r 46 decimal data related to left column of ASCII data 44 149 39 34 3 120 1 0 22 L l a L tn b E Hs Gi PO 0i 0 d C o T SPE 54 28 31 2C 31 53 58 ED 2 8 DE 45 44 20 32 30 OD OA 44 NSITY 5 4E 53 49 59 20 38 OD OA ET PEEL OF 45 54 20 58 45 45 4C 20 46 DIRECTI 46 OD GA 44 49 52 45 43 54 DN 4 GAP AE 4E 20 30 OD OA 47 41 50 20 3 00 0 33 SE 30 30 20 6 6D 26 30 ZE 38 30 20 60 6D OA 52 45 46 ERENCE 8 8 45 52 45 4E 43 45 20 38 2C 30 T GUTT A 53 45 54 20 43 54 54 ER OFF 51 46 52 20 AE 46 46 OD OA 53 49 100 02 BA 45 20 31 30 30 2E 30 32 20
6. B Host Interface Factory opuon TOFD 1039 50 model ua 22 4 LED and Button Functions 23 TT B Drei ACO uen 23 4 2 Regular Button 1 lt 13 68 23 4 2 23 4 3 1 Gap Black Mark Sensor Calibration 24 4 3 2 Gap Black Mark Calibration Self test and Dump Mode 24 4 3 3 Printer 2 27 4 3 4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark SerisOF EE 28 4 3 5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor 28 436 SKIDAUTO BAS mu EHE PURI 28 5 Troubleshooting 30 5 1 LED SAUS sense 30 5 2 Print Problem me 31 5 3 LCD display Option for DT2205 model 32 6 EC OR Rc RUN 33 REVISGIUSION AT D PEPE 35 1 Introduction 1 1 Product Introduction Thank you for purchasing this bar code printer Although the printer has a small footprint it delivers reliable superior performance This printer provides direct thermal printing at user selectable speed of 2 0 3 0 4 0 or 5 0 ips It accept
7. DT2205 DT039 50 DIRECT THERMAL BAR CODE PRINTER USER S MANUAL Contents 1 11 rOAUCUON SS ii Product IMUFOGUCTION RE ii 1 2 COmpliali6 GS uvel 2 Operations Overview 1 2 1 Unpacking and Inspection 41 4 2 1 2 2 Printer e UE 2 221 Sehr me EE 2 2 2 2 INGNOr VIEW engen 3 2253 Hedr VIEW pe 4 3 SON NETTS 5 3 1 Setung UP the d Lu 5 2 2 RE 5 3 2 1 Loading the Media 5 3 2 2 Loading External Media For DT2205 model only 9 3 2 3 Loading Media in Peel off Mode Option 11 3 2 4 Loading Media in Cutter Mode 13 3 3 DIAGNOSUC 100 esc 15 3 3 1 Start the Diagnostic Tool nenne nennenen 15 3 3 2 Printer Function Calibrate sensor Ethernet setup RTC eee 16 3 4 Setting Ethernet by Diagnostic Utility Option for DT2205 model 17 3 4 1 Using USB interface to setup Ethernet interface 17 3 4 2 Using Ethernet interface to setup Ethernet interface 18 3 5 Install MicroSD Memory Card 20 3 6 Mount the Printer on the Wall 21 3 7 Using the PC USB Keyboard with Printer US
8. ED button when LED becomes solid green B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green 4 Printer will be interrupted to run the AUTO BAS program 29 9 Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer If the printer still does not function after all suggested solutions have been invoked please contact the Customer Service Department of your purchased reseller or distributor for assistance 5 1 LED Status This section lists the common problems that according to the LED status and other problems you may encounter when operating the printer Also it provides solutions LED Status Printer Possible Cause Recovery Procedure Color Status OFF Noresponse power Turn on the power switch Check if the green LED is lit on power supply If it is not lit on power supply is broken Check both power connections from the power cord to the power supply and from the power supply to the printer power jack if they are connected securely oolid Green ON The printer is ready to No action necessary NN Green with Pause The printer is paused Press the FEED button to resume for printing Eod EN Red with The out of label or the 1 Out of label blinking printer setting is not Load a roll of label and fo
9. HCP 4 3 4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor Please follow the steps as below 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns green amber after 5 green blinks Any green amber will do during the 5 blinks B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green 4 3 5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor Please follow the steps as below 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns red amber after 5 green amber blinks Any red amber will do during the 5 blinks B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green 4 3 6 Skip AUTO BAS TSPL2 programming language allows user to download an auto execution file to flash memory Printer will run the AUTO BAS program immediately when turning on printer power The AUTO BAS program can be interrupted without running the program by the power on utility 28 Please follow the procedures below to skip an AUTO BAS program 1 Turn off printer power 2 Press the FEED button and then turn on power 3 Release the FE
10. INGER AND OTHER BODY PARTS AWAY 2 THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HAS LITHIUM BATTERY CR2032 INSTALLED RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE 3 DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER INSTRUCTIONS OERSICHT Explosionsgetahr bel unsachgemen Austausch der Batterie Ersatz nur durch denselben oder einem vom Hersteller emptohlenem nlichen Typ Entsorgung gebrauchter Batterien nach Angaben des Herstellers WARNUNG GEF HRLICHE BEWEGLICHE TEILE FINGER UND ANDERE K RPERTEILE FERNHALTEN VORSICHT EXPLOSIONSGEFAHR BEI ERSATZ DER BATTERIE DURCH UNZULASSIGEN TYP VERBRAUCHTE BATTERIEN IMMER VORSCHRIFTSGEMASS ENTSORGEN Note The maximum printing ratio per dot line is 15 for this printer To print the full web black line the maximum black line height is limited to 40 dots which is 5mm for 203 DPI resolution printer 717 713 77 ol 7193822 AA 39552 ae Ee era iii 2 Operations Overview 2 1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping Please carefully inspect the packaging and printer upon receiving the bar code printer Please retain the packaging materials in case you need to reship the printer Unpacking the printer the following items are included in the carton One printer unit One Windows labeling software Windows driver CD disk One quick installation guide
11. anager Command Tool Printer Function Printer Configuration Calibrate Sensor Printer Ethernet Setup eh ATC Setup Milage Check Sum Printer Setup Print Test Page Speed Ribbon Reset Printer Density Code Page Factory Default Paper width unit County Code Dump Text Paper Heightfunit Head up Sensor Ze inch C mm Ignore AUTO BAS Media Sensor Reprint After Error Configuration Gaplunit Gap Inten Printer Status Gap Offset urit Bline Inten Heady Post Print Action Continuous Inten Head Open Paper Jam Dutot Paper Reference Data Bits HibBan End Err Direction v Parity Hikbon Encader Err Offset Stop Bills Pause Shift Cut Piece Baud Rate ddl WA Printing Other Error Shift r Get Status COMI 9600 4 8 1 RTS 2009 9720 TF 03 31 40 Note Please calibrate the gap black mark sensor when changing media Loading path for roll labels DT2205 model DT039 50 model 3 2 2 Loading External Media For DT2205 model only 1 Open the printer s top cover and separate the media holders to fit the media width 2 Press down the media holder lock switch to fix the media holder 3 Feeds the media through the rear external label entrance chute And place the paper printing side face up through the media guides media sensor and place the label leading edge onto the platen roller Rear external label entrance 4 Close the top cover gently 5 Use Diagno
12. edia through the backing paper opening beneath the peel off roller Backing paper opening Peel off roller 4 Push the peel off panel back to the printer 5 Close the top cover gently 6 Press the FEED button to test Backing paper Liner Note Please calibrate the gap black mark sensor when changing media 12 3 2 4 Loading Media in Cutter Mode Option 1 Refer to section 3 2 1 to load the media 2 Lead the media through the cutter paper opening Cutter paper opening 3 Close the top cover gently 4 Use Diagnostic Tool to set the media sensor type and calibrate the selected sensor Start the Diagnostic tool gt Select the Printer Configuration tab gt Click the Calibrate sensor button 13 F 2 9 TE About Language Interface English vi lug Setup Printer Configuration File Manager Bitmap Fort Manager Command Tool Printer Function Printer Configuration Calibrate Sensor Printer Information Version Ethernet Setup Milage Km Check Sum RTC Setup Printer Setup Print Test Page Speed Ribbon _Ethemet Setup Ditze _Print Test Page _ Factory Default Dump Test Code Page Factory Default Paper widthfunit Country Code Dump Text Paper Heightfunit Head up Sensor Ignore AUTO BAS Media Sensor EI Reprint After Error Configuration Gapfunit Gap Inten Printer Status Gap Offset urit Bline Inten D
13. ensity Heady Post Print Action Continuous Inten Head Open L ut Piece Baud Rate Paper Jam DEE Reference Data Bits Ribbor End Err Direction a EN Parity Ribbon Encoder Err Offset Stop Bits Pause 5 hift gt dl I oboe Other Error Shift r Get Status Clear Load Save Set Read LPTI COMI 2600 N 8 1 RTs 2009 8 20 TF 02 31 40 Note Please calibrate the gap black mark sensor when changing media 14 3 3 Diagnostic Tool The Diagnostic Utility is enclosed in the CD disk Utilities directory Users can use this Utility to setup the Ethernet by RS 232 USB and Ethernet interfaces The following contents will instruct users how to configure the Ethernet by these three interfaces Note This utility works with printer firmware V6 00 and later versions 3 3 1 Start the Diagnostic Tool 2 There are four features Printer Configuration File Manager Bitmap Font Manager Command Tool included in the Diagnostic utility Features tab Interface 711 Printer Configuration Calibrate Sensor Printer Infamatian Unit Version Ethernet Setup inch SE Milage Km Check Sum Printer functions ATC Setup Print Test Page Reset Printer Factory Default FETE TE AUTO BAS Page Printer Status Printer Setup S Speed Ribbon h Density Code Page Paper Country Code Paper Height unit Head up Sensor Media Sen
14. er and the printer to the LAN 2 Turn on the printer power 3 Start the Diagnostic Utility by double clicks on the amp DisegToolexe icon Note This utility works with printer firmware V6 00 and later versions 4 Select Ethernet as the interface then click on the Setup button to setup the IP address subnet mask and gateway for the on board Ethernet Interface Setup ETHERNET EEE USE Printer Name MAC P Address ModelName Status 1703350 001B 82FF 020C 1006125 Jr kl FS L75730 00 16 11 C7 67 90 10 0 6 24 DP G321 Ready f 0 0 6 125 Fort E 00 LPT ETHERNET Discover Device Change IP Address Factory Default Web Setup 5 Click the Discover Device button to explore the printers that exist on the network 6 Select the printer in the left side of listed printers the correspondent IP address will be shown in the right side IP address Printer Name field 7 Click Change IP Address to configure the IP address obtained by DHCP or static Ethernet Setup 10 0 6 125 SER JFF Erbe sert mz usnm 3 ateway 0 0 6 253 Printer TTUS3 50 MAC Address 00 18 82 FF 02 0C0 Set Printer Name Set IP Cancel The default IP address is obtained by DHCP To change the setting to static IP address click Static IP radio button then enter the IP address subnet mask and gateway Click Set IP t
15. f the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED becomes amber and blinking Any amber will do during the 5 blinks B The LED color will be changed as following order Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green 4 It calibrates the sensor and measures the label length and prints internal settings then enter the dump mode Note 1 Sensor calibration can be done by Diagnostic Tool or by power on utility Please refer to 3 3 Diagnostic Tool Section for more information 2 Please select gap or black mark sensor type prior to calibrate the sensor 25 Self test Printer will print the printer configuration after gap black mark sensor calibration Self test printout can be used to check if there is any dot damage on the heater element printer configurations and available memory space PRINTER INFO To 1 HAN XXXXXX Version MILRGE m 0 CHECKSUM O6AnO08CB3 SERIAL PORT S500 N 8 1 CODE PAGE 6850 COUNTRY CODE SPEED 5 INCH DENSITY 8 0 SIZE 2 00 2 00 GAP X XX A AA TRANSPRRENCE 16 MILI 001 i Print head test pattern Printer model name amp Main board firmware version Printed mileage Main board firmware checksum Serial port setting Code page Country code Print speed Print darkness Label size
16. gnostic utility quick start guide in the CD disk Utilities directory 16 3 4 Setting Ethernet by Diagnostic Utility Option for DT2205 model The Diagnostic Utility is enclosed in the CD disk Utilities directory Users can use Diagnostic Tool to setup the Ethernet by USB and Ethernet interfaces The following contents will instruct users how to configure the Ethernet by these interfaces 3 4 1 Using USB interface to setup Ethernet interface 1 2 3 Connect the USB cable between the computer and the printer Turn on the printer power Start the Diagnostic Utility by double clicking on the DisgToolexe icon Note This utility works with printer firmware V6 00 and later versions The Diagnostic Utility default interface setting is USB interface If USB interface is connected with printer no other settings need to be changed in the interface field Interface LFT ETHERNET Click on the Ethernet Setup button from Printer Function group in Printer Configuration tab to setup the IP address subnet mask and gateway for the on board Ethernet Printer Function Static IP Calibrate Sensor Ethernet Setup HIC Setup Printer Name PS FFO4E 2 Factory Default ay TT Address IESSE Dump Text Ignore ALITO BAS Configuration Page Set Printer Name Set IP Cancel 17 3 4 2 Using Ethernet interface to setup Ethernet interface 1 Connect the comput
17. llow the instructions in correct loading the media then press the FEED button to resume for printing 2 Printer setting is not correct Initialize the printer by instructions in Power on Utility or Diagnostic Tool Note Printer status can be easily shown on the Diagnostic Tool For more information about the Diagnostic Tool please refer to the instruction in the software CD disk 30 5 2 Print Problem Problem Possible Cause Recovery Procedure Check if interface cable is well cable to interface connected to the interface connector The serial port cable pin configuration is Please replace the cable with pin to pin not pin to pin connected connected mu The serial port setting is not consistent Please reset the serial port setting Not Printing between host and printer The port specified in the Windows driver Select the correct printer port in the is not correct driver The Ethernet IP subnet mask gateway Configure the IP subnet mask and is not configured properly gateway Follow the instructions in loading the No print on the label Label loaded not correctly media Continuous feeding Please do the initialization and The printer setting may go wrong labels gap black mark calibration Gap black mark sensor sensitivity is not Calibrate the gap black mark sensor set properly sensor sensitivity is not enough Paper Jam Make sure label size is set properly Set label size exactly
18. o take effect the settings 18 Users can also change the Printer Name by another model name in this fields then click Set Printer Name to take effect this change Note After clicking the Set Printer Name or Set IP button printer will reset to lake effect the settings Click Exit button to exit the Ethernet interface setup and go back to Diagnostic Tool main screen Factory Default button This function will reset the IP subnet mask gateway parameters obtained by DHCP and reset the printer name Web setup button Except to use the Diagnostic Utility to setup the printer you can also explore and configure the printer settings and status or update the firmware with the IE or Firefox web browser This feature provides a user friendly setup interface and the capability to manage the printer remotely over a network 19 3 5 Install MicroSD Memory Card 1 Open the SD memory card cover DOS FAT file system is supported for the SD card Folders files stored in the SD card should be in the 8 3 filename format 3 6 Mount the Printer on the Wall There are three holes in the bottom of printer Printer can be mounted on the wall by the 3 0mm 3 5mm screw head screws 44mm Note Please hang properly to avoid fall down 21 3 7 Using the PC USB Keyboard with Printer USB Host Interface Factory option for DT039 50 model 1 Turn off the printer power 2 Plug in the PC USB keyboard into printer USB h
19. ost interface 3 Turn on the printer power 4 After pressing the Fi key of the keyboard the printer LCD will display as following 5 Use up or down key of the keyboard to move gt cursor to select either DRAM FLASH or CARD that you previously saved file in and press key of the keyboard to list files 6 Select the file and press key to run the BAS program FLASH List gt 5 1 5 5 2 5 7 Then you can enter the data from keyboard for stand alone application Press PC keyboard Ei key to start this function Press up or down key to move the cursor to the option Press Esc key to return to previous menu Press key to enter run cursor located option Press keys to reset the printer and enter Ready Note USB host is a factory option interface for DT039 50 model 22 4 LED and Button Functions This printer has one button and one three color LED indicator By indicating the LED with different color and pressing the button printer can feed labels pause the printing job select and calibrate the media sensor print printer self test report reset printer to defaults initialization Please refer to the button operation below for different functions 4 1 LED Indicator LED Color This illuminates that the power is on and the device is ready to Green Solid use This illuminates that the system is downloading data from PC to Green Flash memory or the printer is paused
20. power switch is set to off 3 Connect the printer to the computer with the provided USB cable 4 Plug the power cord into the AC power cord socket at the rear of the printer and then plug the power cord into a properly grounded power outlet Note Please switch OFF printer power switch prior to plug in the power cord to printer power jack 3 2 Loading the Media 3 2 1 Loading the Media 1 Open the printer top cover by pulling the tabs located on each side towards the front of the printer and then lift the top cover to the maximum open angle 2 The media holder can be used for 1 and 1 5 media core by rotating the upper part of label holder180 degrees clockwise For DT2205 model only 1 5 3 Separate the media holders to the label roll width DT2205 model DT039 50 model Sensor Platen roller 5 Place the paper printing side face up through the media guides media sensor and place the label leading edge onto the platen roller Media guides 6 Close the top cover gently and make sure the cover latches securely DT2205 model DT039 50 model 7 Use Diagnostic Tool to set the media sensor type and calibrate the selected sensor Start the Diagnostic tool gt Select the Printer Configuration tab gt Click the Calibrate sensor button iiss font About Language 4 Interface English ss Setup Printer Configuration File Manager Bitmap Font M
21. rate the black mark sensor 5 Set gap sensor as media sensor and Release 6SkipAUTO BAS FT Release 4 3 1 Gap Black Mark Sensor Calibration Gap black mark sensor sensitivity should be calibrated at the following conditions 1 A brand new printer 2 Change label stock 3 Printer initialization Please follow the steps below to calibrate the gap black mark sensor 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED becomes red and blinking Any red will do during the 5 blinks B It will calibrate the gap black mark sensor sensitivity B The LED color will be changed as following order Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Note 1 Sensor calibration can be done by Diagnostic Tool or by power on utility Please refer to 3 3 Diagnostic Tool Section for more information 2 Please select gap or black mark sensor type prior to calibrate the sensor 4 3 2 Gap Black Mark Calibration Self test and Dump Mode While calibrate the gap black mark sensor printer will measure the label length print the internal configuration self test on label and then enter the dump mode To calibrate gap or 24 black mark sensor depends on the sensor setting in the last print job Please follow the steps below to calibrate the sensor 1 Turn of
22. s roll feed die cut and fan fold media with gap or black mark All common bar codes formats are available Fonts and bar codes can be printed in 4 directions 8 different alphanumeric bitmap fonts and built in scalable font capability You will enjoy trouble free high throughput for printing labels with this printer 1 2 Compliances CE Class B EN55022 1998 A1 2000 A2 2003 EN55024 1998 A1 2001 A2 2003 IEC 61000 4 Series EN61000 3 2 2006 amp EN61000 3 3 1995 A1 2001 FCC Part 15 Class B UL CUL UL60950 1 C Tick CFR 47 Part 15 CISPR 22 3 Edition 1997 Class B ANSI C63 4 2003 Canadian 5 003 TUV Safety EN60950 1 IEC 60950 1 Wichtige Sicherheits Hinweise 1 Bitte lesen Sie diese Hinweis sorgfaltig durch 2 Heben Sie diese Anleitung f r den spateren Gebrauch auf 3 Vor jedem Reinigen ist das Ger t vom Stromentz zu trennen Verwenden Sie keine Fl ssig oder Aerosolreiniger Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung 4 Die Netzanschlu Steckdose soll nahe dem Ger t angebracht und leicht zug nglich sein 5 Das Gerat ist vor Feuchtigkeit zu sch tzen 6 Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Beschadigungen hervorrufen 7 Beachten Sie beim Anschlu ans Stromnetz die Anschlu werte 8 Dieses Ger t kann bis zu einer Au entemperatur von maximal 40 betrieben werden CAUTION 1 HAZARDOUS MOVING PARTS IN CUTTER MODULE KEEP F
23. sor Reprint After Error Printer setup aap unit Gap Inten Gap Offset unit Bline Inten Fost Print Action Continuous Inten Cut Piece Baud Hate Printer Status Reference Data Bits Direction Sch Parity Offset Stop Shift 3 Shift Y Clear LPTI COMI 9600 N 8 1 RTS 2009 20 FF 03 31 40 15 3 3 2 Printer Function Calibrate sensor Ethernet setup RTC setup 1 Select the PC interface connected with bar code printer 2 Click the Function button to setting 3 The detail functions in the Printer Function Group are listed as below Printer Function Description pma Calibrate Sensor a the sensor specified in the Printer Setup group media sensor field Ethernet Set emet Setup Ethernet Setup Setup the IP address subnet mask gateway for BTC S the on board Ethernet etup RTC Time Synchronize printer Real Time Clock with PC Frint Test Page Print Test Page Print a test page Reset Printer Reset Printer Printer Reboot printer Reboot printer Factory Default Factory Default Initialize the printer and restore the settings to Dump Test Y factory default Ignore ALITO BAS Dump Text To activate the printer dump mode Configuration Page Ignore AUTO BAS Ignore the downloaded AUTO BAS program Configuration Page Print printer configuration Note For more information about Diagnostic Tool please refer to the dia
24. stic Tool to set the media sensor type and calibrate the selected sensor Start the Diagnostic tool gt Select the Printer Configuration tab Click the Calibrate sensor button F 2 9 TE About Language Interface English vi lug Setup Printer Configuration File Manager Bitmap Fort Manager Command Tool Printer Function Printer Configuration Calibrate Sensor Printer Information Version Ethernet Setup ATC Setup Miage m Check Sum Printer Setup Print Test Page Speed Ribbon Reset Printer Density p Code Page Factory Default Paper widthfunit Country Code Dump Text Paper Heightfunit Head up Sensor Ignore ALITO BAS Media Sensor vi Reprint After Error Configuration Page Gapfunit Gap Inten Printer Status Gap Offset urit Bline Inten Heady Post Print Action Continuous Inten Head Open L ut Piece Baud Rate Paper Jam DEE Reference Data Bits Ribbor End Err Direction a EN Parity Ribbon Encoder Err Offset Stop Bits Pause 5 hift gt dl I oboe Other Error Shift r Get Status Clear Load Save Set Read LPTI COMI 2600 N 8 1 RTs 2009 8 20 TF 02 31 40 Note Please calibrate the gap black mark sensor when changing media 10 3 2 3 Loading Media in Peel off Mode Option 1 Refer to section 3 2 1 to load the media 2 Open the top cover and peel off panel after calibrated the sensor Peel off panel 3 Lead the m
25. to take label away to print the next label Cutter jam There is no cutter installed on the printer Cutter or cutter driver circuit board is damaged 32 Please close the top cover Supply a new label roll Please refer to the steps in user s manual to reinstall the label roll Calibrate the gap black mark sensor Calibrate the gap black mark sensor Set label size correctly Delete unused files in the FLASH DRAM or MicroSD card Please take the label away to print the next label if peeler module is installed If peeler module is installed and label is been taken away but the message remains Please check if the peeler module connector is connected to main board properly If peeler module is not installed please disable the peeler function Remove the jammed label Make sure the media thickness is equal or less than 0 19mm Replace the cutter or cutter driver circuit board 6 Maintenance This session presents the clean tools and methods to maintain your printer Please use one of following material to clean the printer Cotton swab Head cleaner pen Lint free cloth Vacuum Blower brush 100 ethanol BH E E HB The cleaning process is described as following pe pn Method Intervet 1 Always turn off the printer before cleaning Clean the print head when changing a the print head 2 Allow the print head to cool for a minimum of one minute 3 Use a co
26. tton swab and 100 ethanol to clean the print head surface Print Head Print Head Print Head Element Head Cleaner Pen 1 Turn the power off Clean the platen roller when changing 2 Rotate the platen roller and wipe it a new label roll Platen Roller thoroughly with 100 ethanol and a cotton swab or lint free cloth Use the lint free cloth with 100 ethanol to As needed Tear Bar Peel Bar it Sensor Compressed air or vacuum gt air or vacuum Monthly weie Bishorvecwm eng O OO Note Donottouch printer head by hand If you touch it careless please use ethanol to clean it e Please use 100 Ethenol DO NOT use medical alcohol which may damage the printer head 33 Regularly clean the print head and supply sensors once change a new media to keep printer performance and extend printer life The maximum printing ratio per dot line is 15 for this printer To print the full web black line the maximum black line height is limited to 40 dots which is 5mm for 203 DPI resolution printer 34 Revise History Date Content 2010 3 3 Revise 1 2 section 2010 6 2 3 7 section Using the keyboard with USC host interface Revise 3 1 amp 2 2 3 sections 2010 11 23 Revise 1 2 and 2 2 3 section 35
Download Pdf Manuals
Related Search