Anatomy of Spartan Stringing Machine
Contents
1. the jaws of the Spartan swivel clamps Insert these two swivel clamps into their bases on the turntable Insert the string gripper into the drum Use the 3mm Allen wrench to lock it in place by tightening the string griper locking screw2. TABLE OF CONTENTS OBSAH SECTION PAGE 1 UNPACKING AND INSPECTION 3 INSTALLATION PROCEDURE 3 MOUNTING THE RACQUET FOR STRINGING 5 MAINTENANCE 6 TROUBLESHOOTING 6 APPENDIX A B C OPTIONS AND SUPPLIES A 1 ADJUST STRING CLAMP TO THE CORRECT HOLDING PRESSURE B 1 ADJUST THE BASE OF THE SWIVEL CLAMP TO THE CORRECT HOLDING PRESSURE D B 1 STRINGING INSTRUCTIONS D 1 Anatomy of Spartan Stringing Machine Swivel Clamp V shaped Side Support Side support Arm Throat Mounting Post Frame Retainer Plastic Adapter Throat Mounting Post Micro adjustment Knob Throat Side support Arm us Micro adjustment Knob A Throat Mounting Stock NG 3 Turntable 777 Dr Pa A a Swivel Clamp Base Mounting Stock Locking Knob Turntable Base p K shaped Side Support Frame Retainer Head Mounting Post E tk Head Mounting Post Micro adjustment Knob Head Side support Arm Micro adjustment Knob Head Mounting Stock UNPACKING AND INSPECTION The Spartan stringing machine is packaged and shipped in one carton and is protected internally by foam inserts The Spartan stringing machine is packed with the following components One machine base assembly one tensioner post assembly one tension rod one tension weight assembly including two tension weights one turntable assembly two mounting stocks including two side support arm assemblies two mounting post assembli
3. es two string clamps one user s manual Accessories four K shaped side supports one 6mm Allen wrench hex wrench one 3mm Allen wrench hex wrench Before unpacking any carton inspect the carton for damage Unpack the Spartan stringing machine from the shipping carton by using the following procedure Step 1 Cut the carton sealing tape and open all the carton flaps Step 2 Remove the top packing protector Step 3 Carefully lift the turntable assembly and tension rod out of the carton Step 4 Remove the two mounting stock assemblies two string clamps and accessory bag out of the carton Step 5 Remove the tension weight assembly out of the carton Step 6 Carefully lift the tensioner post assembly and the machine base assembly out of the carton Step 7 Inspect the Spartan stringing machine for obvious damage Step 8 Remove the bottom packing protector out of the carton The accessories sometimes fall beneath the packing protector This Spartan stringing machine has been assembled and tested in production line After passed the inspection by the quality control department this Spartan stringing machine was disassembled into a few major components and packaged into boxes for shipment NOTE The Spartan stringing machine was pre assembled and tested in the production line Therefore there are the assembly marks on the machine base turntable and tension rod If any item is missing or damaged contact your delivery agent a
4. nd your sales representative Retain the packaging materials and shipping container in the event that reshipping is required INSTALLATION PROCEDURE Step 1 Place the Spartan machine base assembly firmly on the table Mount the tensioner post on the base Line up two holes of the tensioner post with holes in the base Use the 6mm Allen wrench to lock it in place by tightening these two screws Step2 Make sure the machine base rests evenly on the table If necessary adjust the level adjustment pad to level the machine base Step3 Lower the tension rod to the right side Step 4 Use the 10mm wrench to turn the tension rod holding screw clockwise to lock it in place Step 5 Mount the turntable on the turntable base Line up four holes of the turntable with holes in the turntable base Use the 6mm Allen wrench to lock it in place by Step 6 Step 7 Step 8 Step 9 tightening these four screws Install the head mounting stock into the track on the turntable Make sure the mounting stock moves smoothly along the track Repeat this operation for the throat mounting stock Remove the mounting post micro adjustment knob from the mounting post assembly Slide the mounting post assembly into the head mounting stock and the side support arm assembly Attach the mounting post micro adjustment knob back to the mounting post assembly Repeat this operation for the throat mounting post Use a soft cloth to wipe off the grease out of
Download Pdf Manuals
Related Search