User Guide
Contents
1. blackout or no no blackout mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again N Color Mode Press the MENU button up to when the is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 2 JL split color mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go normal or back to the functions without any change press the MENU button again Pan Inversion Press the MENU button up to when the P Hn is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the O02 pan inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go normal or back to the functions without any change press the MENU button again LI NIE LLL Inversion UL Barrel Rotation Inversion Press the MENU button up to when the IOE is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to2. 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check in the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit 3H C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the unit Set the proper address D No response to the sound 1 Make sure the unit that does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition F The lamp is cutting out intermittently 1 The lamp is not working well Check the main voltage either too high or too low 2 Internal temperature may be too high Check and if necessary replace the fan on the head 1 Safety Instruction AN WARNING Please read carefully the instruction
3. Rainbow effect Q 128 Slowest speed Rainbow effet 118 127 Pink 107 117 Yellow 096 106 Orange 086 085 Light Green 075 085 UV Purple 064 074 Blue 054 063 Red 043 053 Amber 032 042 Light Blue 022 031 Magenta 011 021 Green 000 010 White 245 Fastest speed clockwise 010 Fastest speed counterclockwise 000 009 Stopped E 135 Slowest speed clockwise 121 134 Stopped 120 Slowest speed counterclockwise 255 Fastest speed Rainbow effect Q 128 Slowest speed Rainbow effect 121 127 Pink 113 120 Yellow Pink 108 112 Yellow 098 105 Orange Yellow 091 097 Orange 083 090 Light Green Orange 076 0582 Light Green 068 075 UV Purple 061 067 Blue 053 060 Red Blue 046 052 R ed 038 045 Amber 031 037 Light Blue 023 030 Magenta 016 022 Green Magenta 008 015 Green 000 007 White 247 Fastest speed Shaking 4 4 131 Fastest speed shutter 4 4 16 Slowest speed shutter 008 015 Open 600 007 Blackout 128 Slowest speed Gobo change 120 127 111 119 103 110 094 102 132 Slowest speed shaking 086 093 077 085 069 076 060 068 052 059 043 051 035 042 026 034 018 025 009 017 000 008 1 Reflector 246 255 Stopped 245 Fastest speed clockwise 135 Slowest speed clockwise 121 134 Stopped 120 Slowest speed counterclockwise 010 Fastest speed counterclockwise 000 009 Stopped IR 6SD IR 6BD IR 6S IR 6B IR 5S IR 5BIR 4C 1 4 is 4 channel color changer 2 2 Bea
4. 060 Red Blue 043 053 Amber Distance 038 045 Amber 032 042 Light Blue 031 037 Light Blue IS 4 IS 3 Beam angle 25 degree Distance m 128 Slowest speed Rainbow effet 096 106 Orange 075 085 UV Purple Distance m 022 031 Magenta 023 030 Magenta 016 022 Green Magenta 008 015 Green 000 010 White 000 007 White 011 021 Green In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switching off MSD 250 2 GY 9 5 IR 7S 7B IR 5C CDM 150W IR 6SD IR 6BD ELC 24V 250W IR 6S IR 6B IR 5S IR 5B IR 4C IS 6S IS 6B IS 4 1S 3 Diagram for lamp changing Because of its high internal pressure there might be a risk that the Discharge lamp would explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp MSD 250 2 1 Always switch off the main supply and never handle CDM 150W the lamp or luminaries when is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age t
5. Connection The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels DMX512 COMMON 120 ohm 1 4Ww INPUT OUTPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 If you using a controller with 5 pins DMX output you need to use a 5 to pin adapter cable 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMXc output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not branched or split toa Y cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pin XLR 3
6. e main functions without any cha without any change press the MENU button Slave Mode the ENTER button to setup or automatically nge after 8 seconds To go back to the functions again 5 3 1 iSolution Operation Consistent DMX configuration enable iRock and iShow to be linked together and controlled at the same time DMX address can be set remotely by iLead controller please refer to the user manual of iLead controller No need to calculate the DMX channels of each fixture in the chain Automatic switching between DMX function and built in stand alone programs 5 3 2 DMX Controller An universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units DMX address can be set remotely by IL 0824 controller No need to calculate the DMX channels of each fixture in the chain Following DMX address setting is based on that all the lighting fixtures are linked tog
7. echnical Specifications IR 7S IR 7B IR 5C AC 120V 60Hz or AC 230 240 250V 50 60Hz 20mm Glass T10A Fast Blow 695 x 340 x 250 mm IR 7S IR 7B 360 x 340 x 250 mm IR 5C 15 kg D Dimension IR 6SD IR 6BD AC 120V 60Hz AC 230 240 250V 50 60Hz 20mm Glass T6 3A Fast Blow CDM 150W 695 x 340 x 250 mm Weight 10 7 kg IR 6S IR 6B IR 5S IR 5B IR 4C Power AC 120V 60Hz AC 230 240 250V 50 60Hz Fuse 20mm Glass T6 3A Fast Blow 20mm Glass T5A Fast Blow Lamp ELC 24V 250W 695 x 340 x 250 mm IR 6S 6B 5S 5B 360 x 340 x 250 mm IR 4C 10 6 E IR EU 6B IR 5S IR 5B IS 6S IS 6B IS 3 IS 4 Power AC 120V 60Hz AC 230 240 250V 50 60Hz 20mm Glass T6 3A Fast Blow 20mm Glass T5A Fast Blow ELC 24V 250W 685 380 x 200 mm IS 6S IS 6B 375 x 380 200 mm IS 4 IS 3 Dimension 9 4 kg Innovation Quality Performance Z Solution Your integrated Solution LINKABLE maT STAND ALONE CC iRock TB iRack 6B iRack 7TS iRack 65 iRoack 5C iRock AC iRock 6BD iRock 5B iRock 6SD iRock 5S iShow 63 iShow 6B iShow 3i1Show 4 User Guide Professional Entertainment Technology TABLE OF CONTENTS Safety Instruction Technical Specification 2 1 Inserting Exchanging rotating gobos 2 2 Beam Angle Lamp How To Set The Unit 4 1 Control Panel 4 2 Main Function How To Control The Unit 5 1 Master Slave Built In Preprogrammed Function 5 2 Easy Controller 5 3 iSolution Operati
8. emperature and improper handling of the lamp Do not use the lamp any longer than its specified life Make sure the lamp is located the center of the reflector for the best spot ELC 24V 250W IR 7S 7B 5C IR 5C is a 5 channel color changer DMX512 Configuration Ch2 cn3 CH Barrel Shutter Shaking 246 255 Stopped 248 255 Open IR 7S 7B IR 5C Pan n Tit v 255 Fastest speed Gobo change 245Fastest speed clockwise 247 Fastest speed Shaking C 4 1 128 Slowest speed Gobo change 132 Slowest speed shaking 13558lowest speed clockwise 131 Fastest speed shutter 121 134 Stopped 120 Slowest peed counterclockwise D1 Fastest speed counterclockwise 18 Slowest speed shutter 008 015 Open 000 007 Blackout 255 Fatest speed Rainbow effect 255 Fastest speed Rainbow effect Q 128 Slowest speed Ranbow effet 116 127 Pink 103 115 Light Green 080 102 UY Purple O 7 089 Blue 064 076 Orange 052 063 Yellow 038 051 Light Blue 026 038 Magenta 013 025 Green 000 012 White Q 128 Slowest speed Rainbow effect 121 127 Pink 113 120 Light Green 106 112 UVPurple light Green 088 105 UV Furple 091 097 Blue UV Purple 083 090 Blue 076 082 Orang e Blue 068 075 Orange 061 067 Yelow Orange 053 060 Yellow 046 052 Light Blue Yellaw 038 045 Lignt Blue 031 037 Wagenta Light Blue 023 030 Magenta 016 022 Greent Magenta 008 015 Green 000 007 W
9. ether controlled by the 8 channel iLead IL 0824 controller IR 7S IR 7B IR 6S IR 6B IR 6SD IR 6BD IR 5S IR 5B IS 6S IS 6B wp eS IR 5C IR 4C IS 4 IS 3 ei 5 2 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote control on the first unit will control all the other units as below ries Sarnia Controller Built in lighting shows triggered by Easy Controller IR 7S Stand by Blackout the unit IR 7B IR 6SD Function Strobe X Y moving pattern selection Color Gobo selection X Y moving setting IR 6BD 1 Gobo Color sync strobe 12 patterns 1 Hold on for gobo change 1 Pan position IR 6S 2 Sync strobe 2 Press shortly for color 2 Tilt position IR 6B 3 Two light strobe change 3 Dimmer IR 5S IR 5B Mode Sound 1 Sound 2 Slow Sound 3 Position Latch LED off LED normal blinking LED on LED fast blinking Function Strobe Chase pattern selection Color Gobo selection Dimmer setting 1 Gobo Color sync strobe 6 patterns 1 Hold on for gobo change 2 Sync strobe 2 Press shortly for color 3 Two light strobe change Mode Sound 1 Sound 2 Slow Latch LED off LED normal blinking LED on LED fast blinking IS 6S Stand by Blackout the unit 6B 4 3 IR 5C Stand by Blackout the unit IR 4C Function Strobe X Y moving pattern selection Co
10. hite 245 Fastest speed dockwise 135 Slowest speed dockwise 121 134 Stopped 120 Slowest speed counterclackwise Q 010 Fastes speed counterclockwise 000 008 Stopped 5 4 DMX512 Configuration 4 How To Set The Unit IR 6BD 6B Pan Color SO Dimmer SOUND Me rw m mm em feo we Emme m me mm DMX MIN MAX ONLYFORREMOTE MASTER SENSITIVITY CONTROL CA 8 SLAVE DMXIN DMX OUT Displa aking unction To show the various menu and the selected functions Shutter a DMX On DMXinput present Sat 9H SLAVE On Slave Mode ii Shaking G9be Color Reflector SOUND Flashing Sound activation aking olor unction MENU to select the programming functions DOWN to go backward in the selected functions UP lto go forward in the selected functions ENTER to confirm the selected functions Remote controller input By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode Sensitivity To adjust the sound sensitivity Microphone To receives audio signal for sound activation DMX input output For DMX512 link use 3 pin XLR plug cable to link the unit together 4 2 Function To select any of the given functions press the MENU button up to when the required one is showing on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the re
11. ing problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack or power pack Do not touch any wire during operation as high voltage might be causing electric shock To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using Hot lamp explosion hazard Do not open the unit within five minutes after switching off Do not start on the unit without bulb enclosure or housing are damaged 9 9 The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Do not look directly at the light while the bulb is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 20 kgs for each unit 5 5 512
12. ion through an internal microphone to create an intelligent effect t can be operated by DMX512 control or can be used as an individual unit without a controller Consistent DMX channel enable iRock iShow and iMove to be link together Features different preprogrammed chase patterns Please use a 3 pin XLR cable plug when connecting units together Accurate focusable optics system and ultra smooth stepping motors Fan cooling Pan 180 deg Tilt 70 deg IR 7S IR 7B IR 6SD IR 6BD IR 6S IR 6B IR 5S IR 5B IS 6S IS 6B IR 7S IR 7B Independent gobo wheel with 7 rotating replaceable gobos plus open including 4 metal 2 glass and 1 effect gobos with shaking effect Independent color wheel with 9 dichroic colors with rainbow effect and independent shutter amp dimmer IR 6S IR 6B Independent gobo wheel with 14 gobos plus open and blackout including 10 metal 1 replaceable gobo 2 glass and 1 effect gobos with shaking effect Independent color wheel with 11 dichroic colors with rainbow effect and independent shutter amp dimmer IR 5S IR 5B without dimmer IR 5C Independent gobo wheel with 7 rotating replaceable gobos plus open including 1 metal 2 glass 1 effect 1 frost gobos and 2 color temperature filters 5600k amp 3200k with shaking effect Independent color wheel with 9 dichroic colors with rainbow effect and independent shutter amp dimmer IR 4C Independent gobo wheel with 14 gobos plus open and black
13. lor Gobo selection X Y moving setting 1 Gobo Color sync strobe 12 patterns 1 Hold on for gobo change 1 Pan position 2 Sync strobe 2 Press shortly for color 2 Tilt position 3 Two light strobe change Position Latch Mode Sound 1 Sound 2 Slow Sound 3 LED off LED normal blinking LED on LED fast blinking Stand by Blackout the unit IS IS Function Strobe Gobo Color selection 1 Gobo Color sync strobe 1 Hold on for gobo change 2 Sync strobe 2 Press shortly for color change S 3 Two light strobe Mode Sound Slow LED off LED on Stand by Blackout the unit Function Strobe Gobo Color selection 1 Gobo Color sync strobe 2 Sync strobe 3 Two light strobe LED off LED on X Y moving pattern mv x MW Press the MENU button up to when the button and the display will blink Use DOWN and UP button to select the normal or 2 light show mode or 3 light show mode or 4 light show Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any is showing on the display Pressing ENTER change press the MENU button again lin Blackout Mode Lite is showing on the display Pressing ENTER Press the MENU button up to when the button and the display will blink Use DOWN and UP button to select the yes
14. m Angel DMX512 Configuration Ch ene rrel v IR 7S 7B Beam angle 14 degree IR 6SD IR 6BD CDM LAMP Beam angle 14 degree IR 6S 6B 5S 5B 246 5 248 255 2 46 255 Stopped pen IR GSD GBD IR AC 255 Fastest speed Gobo change 550 2650 1000 245 Fastest speed clockwise 247 Fastestspeed Shaking 120 127 Or 105 110 Distance Distance 132 Slowest speed shaking 135 Slowest speed clockwise 094 102 IR 6S 6B 5S 5B neam angle 14 degree 5000 1800 750 lux 086 093 131 Fastest speed shutter 121 134 Stopped 077 085 IS 6S IS 6B Beam angle 22 degree LESE LIT E LJ 2 1 1 1205lowest speed counterclockwise 069 076 I 052 056 mE 043 051 16 Slowest speed shutter WE 035 042 Distance m 0 65 026 034 008 015 Open 1 9 O1 Fastest speed counterclockwise 018 025 n 1 2 3 4 5 6 IR 5C Beam angle 17 degree Distance m 008 017 7H eo sooQoscotoo e 0008 2800090008 J Color Normal Split 255 Fatest speed Rainbow effect 255 Fastest speed Rainbow effect Q Q 128 Slowest speed Rainbow effect 121 127 Pink 118 127 Pink 113 120 Yellow Pink IR 4C Beam angle 16 degree 107 117 Yellow 106 112 Yellow 7300 1170 600 lux 098 105 Orange Yalow 091 097 Orange 086 095 Light Green 083 090 Light Green Orange 075 082 Light Green 068 075UV Purple 061 067 054 063 Red 053
15. nly on the second unit to get
16. on Universal DMX Controller 5 4 Universal DMX Controller 5 5 DMX512 Configuration 5 6 DMX512 Connection Troubleshooting Fixture Cleaning 2H T Fixture Cleaninc The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements 6 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connect power and main fuse
17. out including 7 metal 1 replaceable 1 effect 1 frost 2 glass gobos and 2 color temperature filters 5600k amp 3200k with shaking effect Independent color wheel with 11 dichroic colors with rainbow effect and independent shutter amp dimmer S 6S IS 6B IS 4 Professional multi gobo rotator 14 gobos plus open and blackout including 10 metal 1 replaceable gobo 2 glass and 1 effect gobos with shaking and shutter effect Independent color wheel with 11 dichroic colors with rainbow effect 15 3 Professional multi gobo rotator 14 gobos colors plus open and blackout including 10 metal 1 replaceable gobo 2 glass and 1 effect gobos with shaking and shutter effect IS 6S IS 6B IS 4 IS 4 is 4 channel gobo rotator For IR 7S IR 7B IR nlv Ch1 Ch2 re Pan Tilt Barrel 248 255 Open 255 Fastest speed Gobo change 2 1 Inserting Exchanging rotating gobos DANGER Install the gobos with the device switched off only Unplug from mains before Open the cover by loosening the fastening screw at the sides of the cover If you wish to use other forms and patterns as the standard gobos or if the gobos are to be exchanged remove the fixation ring with an appropriate tool Remove the gobo and insert the new gobo Press the fixation ring together and insert it in the front of the gobo 6H CAUTION Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened 255 Fatest speed
18. pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 15 3 DMX512 Configuration C1 _ 4c Shutter Shaking Ch1 248 255 Open 247 Fastest speed Shaking 4 1 132 Slowest speed shaking 131 Fastest speed shutter 16 Slowest speed shutter 008 015 Open 000 007 Blackout 255 Fastest speed Gabo change 128 Slowest speed Gobo change 120 127 111 119 Magenta 103 110 094 102 086 093 077 085 069 076 060 068 052 059 043 051 035 042 026 034 018 025 009 017 000 008 White Blue Magenta ox BluetMagenta Red UV Purple Yellow Greent Yellow vis Magenta Blue Green Magenta Red White 246 255 Stopped 245 Fastest speed clackwise 135 Slowest speed clockwise 121 134 Stopped 120 Slowest speed counterclockwise 010 Fastest speed counterclackwise 000 009 Stopped 2 Technical Specification e Voltage AC 120V 60Hz or 230V 240V 250V 50 60Hz Bulb MSD 250 2 GY9 5 IR 7S IR 7B IR 5C CDM 150W IR 6SD IR 6BD ELC 24V 250W IR 6S IR 6B IR 5S IR 5B IR 4C IS 6S IS 6B IS 4 IS 3 The unit is DMX512 fixture It features full DMX512 control It can also be linked together in master slave connection as many as required in and run by built in program chase sequences automatically or by sound activat
19. preprogram function 2 By easy controller 3 By IL 0824 please refer to the user guide of iLead controller or universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show its item number on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to set in slave mode Suid and select 2b normal or SLI Ie 2 light show mode 3 light show mode or 4 light show Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on and only for color change 2 light show L means the unit works normally and SIL e means 2 light In Sud slave mode show In order to create a great light show you can set Ie contrast movement to each other even if you have two units o
20. quired mode has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are showing below m LL LL lm F 1 Lh CL Lr un LL 2 LC Cr a rna MENU r m UN a a mm POL Self Test SHE Reset DMX512 Address Setting Normal 2 Light Show Slave mode 3 Light Show Slave mode 4 Light Show Blackout Mode Yes Blackout Blackout Mode No Blackout Normal Color Split Color Pan Normal Pan Inversion Tilt Barrel Normal Tilt Barrel Inversion Dimmer Normal Dimmer Inversion LED on LED off Display Normal Display Inversion Slave mode Slave mode 10H Focus Adjust Fixture Hours SL sand St only for color change DMX512 Address Setting Press the MENU button up to when the Hee is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press return to th
21. select the noa normal or j tilt oarrel rotation inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Dimmer Inversion Press the MENU button up to when the d is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the normal or dimmer inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Led Display Press the MENU button up to when the Licid button and the display will blink Use DOWN and UP buiton to select the On Led on or Led off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back is showing on the display Pressing ENTER to the functions without any change press the MENU button again Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to when the dar display inversion It will au
22. tomatically store after 8 seconds Or press the ENTER is blinking on the display Use the ENTER button to change to the mode button again return to the mode display normal To go back to the functions press the MENU button again Display normal mode for the fixture putting on the floor Display inversion mode for the fixture fixing under ceiling Focus Adjust Press the MENU button up to when the Oe d is blinking on the display Pressing ENTER button the unit will focus on center position To go back to the functions press the MENU button again L IL Self Test Press the MENU button up to when the EeSE is blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again 12H Fixture Hours Press the MENU button up to when the is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again Reset Press the MENU button up to when the aet is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in
23. which includes important information about installation operation and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this user guide Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before fuse lamp replacement or servicing Replace fuse lamp only with the same type Do not use any other type of lamp Make sure there is no flammable materials close to the unit while operating as it is fire hazard Use safety cable when fixes this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is 40C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85C Don t touch the housing bare hand during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing bulb or serving as the unit could be very hot In the event of serious operat
Download Pdf Manuals
Related Search