MS100 Manual 1.1
Contents
1. Thermo Shaker Cat MS 100 User Manual ver 1 1 en Gingko Biotech 9924 Mesa Rim Road San Diego CA 92121 www gingkobiotech com sales gingkobiotech com Contents 1 Introduction oo AA 3 1 1 Features 1 2 Specifications 2 Safety Precautions and Application Limitation 4 3 Cleaning and Maintenance 0c eee eee 4 A Unpacking and Installation ii 5 5 Control Keys and Display Panel 6 6 Operation Instructions ii 7 6 1 Turning on device 6 2 Setting temperature mixing speed and time 6 3 Routine run 6 4 Incubation only mode 6 5 Mixing only mode 6 6 Brief mix 7 Change Sample Block 0 00 eee eens 8 8 Troubleshooting 000 cee cece eee ee 9 9924 Mesa Rim Road San Diego CA 92121 www gingkobiotech com sales gingkobiotech com 1 Introduction Thermo Shaker MS 100 is designed for incubating and mixing aqueous solutions in sealed micro test tubes It combines incubator and shaker functions in one The incubation temperature can be precisely maintained between 5 C above room temperature and 99 C and the shaker speed between 200 and 1500 revolutions per minute rom The value of temperature and speed are independently set and controlled 1 1 Features Independent control of time temperature and shaking speed Two segment programmable parameter settings Back lit LCD display Simultaneous display of time temperatu2. aker unit with one sample block pre installed one power cord and one User Manual If you have ordered additional sample blocks make sure that they are included in the special order package If any item is missing contact your vendor or Gingko Biotechnology s Service Department immediately Save the original packaging until the unit has been shown to work properly Place the device onto a flat stable bench surface To ensure sufficient ventilation keep at least 10 cm of clearance space around Thermo Shaker Check the label on the back panel to verify that the unit is rated your local power voltage Plug the device to a wall outlet the electrical power cord is included in the delivery package Turn on the switch located next to the power socket on the rear panel It is advisable to carry out a test run at maximum speed to check the stability of the device and to ensure that it will move on the bench top during mixing Sample Block Control Display Panel Power Switch Power Socket Fuse holder 9924 Mesa Rim Road San Diego CA 92121 www gingkobiotech com sales gingkobiotech com 5 Control Keys and Display Panel True Value Set Value Increase temperature speed time Turn on or off temperature speed time control Start and stop a run Press and hold to terminate current run Decrease temperature speed time Move cursor 9924 Mesa Rim Road San Diego CA 92121 www gingkob
3. bate explosive or highly reactive substances The operation ambient temperature is between 4 C to 35 C The technical data is valid at ambient temperature between 15 C and 35 C When mixing and incubating toxic or pathogenic samples safety regulations must be followed In connection with this please note that the plastic sample block lids is NOT a protective device it only provides thermal insulation After transferring the device from a cold room to a warmer room water may condense on the device Do not use the device for approximately one hour to allow the condensation to dry Thermo Shaker is an electrical device Do not spill large quantities of liquid onto the device 3 Cleaning and Maintenance Disconnect the unit from the power source before cleaning The unit should be cleaned with a soft damp cloth or paper towel Do not use harsh cleaner organic solvent or aerosol spray Do not submerge the unit to water Do not use the unit near water sources 9924 Mesa Rim Road San Diego CA 92121 www gingkobiotech com sales gingkobiotech com 4 Unpacking and Installation Upon receiving your Thermo Shaker examine the package for any damage In the event of shipping damage a claim must be filed with the transportation carrier within 10 days Remove the packing material and accessories from the box Lift the unit out of the box Do not lift Thermo Shaker by its sample block lid The standard package includes one Thermo Sh
4. iotech com sales gingkobiotech com 6 Operation Instructions 6 1 Turning on device Turn on the power switch located on the back System Testing ee esa should appear for about 6 seconds during a routine self test of the ystem 1 esung device Then the parameter set values from previous run will appear LL and the device will automatically heat up to the stored temperature set value 6 2 Setting temperature mixing speed and time Setting control values of a run After pressing set key once device enters its programming mode and a cursor appears Press set key further to move the cursor to the value to be adjusted temperature speed time Adjust the value by pressing A and V keys Setting off control of temperature speed time move cursor to the parameter to be turned off i e uncontrolled and press off key set key is not functional while shaker is running Time OFF means continuous operation Parameters can not be set off altogether at the same time PV 255 0 00 00 SV 60 0 1000 20 00 PV 255 0 00 00 SV OFF 1000 20 00 6 3 Routine run After setting the values wait for 4 seconds until the cursor disappears Press start stop key to start the run The temperature increases to the set value first and then shaker will start and time display starts to count down After completion device stops automatically Program Ends appears on display
5. on the device b Place the four bolts to mounting holes and tighten the bolts with a hex wrench 9924 Mesa Rim Road San Diego CA 92121 www gingkobiotech com sales gingkobiotech com 8 Troubleshooting No display No power Check and restore power Blown fuse Replace fuse Broken switch Replace power switch Others Contact vendor Large discrepancy between the broken sensor Contact vendor displayed temperature and the actual Temperature display shows Ambient temperature lt 0 C Increase ambient temp OPEN or SHORT and audio Broken thermal sensor Contact vendor alarm turns on Sample block does not heat up Broken thermal sensor Contact vendor Control key s does t respond Broken membrane switch Contact vendor 9924 Mesa Rim Road San Diego CA 92121 www gingkobiotech com sales gingkobiotech com
6. panel and audio alert goes off Press and hold down start stop key for few seconds to manually stop the shaker The temperature maintains its set value and time display becomes 00 00 Press start stop again to restart the run 6 4 Incubation only mode Use set key to move cursor to under speed set value Press off key to change the value to be OFF Wait about 4 sec till cursor disappears Press start stop key to start the incubator without shaking 6 5 Mixing only mode Use set key to move cursor to temperature set value Press off key to change the value to OFF Wait till cursor disappears Press start stop key to start the shaker without temperature control 6 6 Brief mix Use the set key to move the cursor under time set value Press A or V key to set the value to 00 00 Press the start stop key and the device starts shaking for 6 sec at the set value of speed 9924 Mesa Rim Road San Diego CA 92121 www gingkobiotech com sales gingkobiotech com 7 Change Sample Block Before change the block unplug the power cord to the unit The block may be hot Protect hands if the unit has been used at elevated temperatures Block Removal a Open the transparent plastic lid and unscrew the four bolts as indicate b Close the lid and move the block from the unit Block Installation a Line up the holes on the block with the holes
7. re and shaking speed Over heating protection for safety amp reliability Temperature can be calibrated to meet user s needs Audio signal upon program completion Various optional interchangeable blocks to accommodate different tubes amp wells for your experimental needs Blocks are easy to clean and sterilize Customized blocks are available upon request Four types of standard sample blocks are available A Block 0 2 ml x 96 wells B Block 0 5 ml x 54 wells C Block 1 5 ml x35 wells D Block 2 0 ml x 35 wells 1 2 Specifications Performance All specifications are valid at ambient temperatures from 5 to 30 Temperature control range from 5 C above room temperature to 99 C Temperature accuracy 0 5 C Heating rate 5 5 C min Mixing frequency 200 to 1 500 rpm Mixing stroke 2 mm Timer range 1 min to 99h 59 min Physical characteristics Power supply 100 120VAC 50 60 Hz 150W Fuse 250V 2 5A 5x20 Size Width x Depth x Height 30 0 x 21 2 x 18 0 cm Weight 7 0 kg Operation ambient conditions Relative humidity lt 70 Temperature 5 C to 30 C 9924 Mesa Rim Road San Diego CA 92121 www gingkobiotech com sales gingkobiotech com 2 Safety Precaution and Application Limitation Thermo Shaker is for research purpose and should be handled only by experienced laboratory personnel Thermo Shaker must NOT be operated in a flammable environment and must NOT be used to mix incu
Download Pdf Manuals
Related Search