Home

Home Prosafe 1132 GSM

1. Alr Ok Folr jc le m Step 2 Press OK to double confirm Step 3 The Exit Delay counting down screen is displayed as in above section Step 4 When the Exit Delay time is up the Control Panel will sound a long beep The Alarm On will display on the screen and the system is in Arm mode lt NOTE gt Any time pressing followed by PIN Code and OK the screen returns to Alarm Off The Fault DSP screen has a time out for 5 minutes It will automatically exit and return to Alarm Off screen after 5 minutes f a sensor is by passed Please see section Partial Arm mode the fault condition of that sensor will not be checked f a sensor tampered or out of order occurs you can temporarily by pass it or permanently remove it Arming with Door Opened O While you arm the system if any door was detected to be open the Control Panel will also sound a ding dong warning sound to indicate arming is prohibited The message Fault DSP is displayed in the middle of the top display row and CTC 1132 868AM 29 alternates at 2 second intervals with the sensor name that is being triggered At this moment you can close the opened door after which the fault display will be cleared automatically and the screen returns to Alarm off You then can arm the system again However if
2. The maximum length of Address message is 8 sec When the 8 sec duration is over recording will be stopped automatically The message being recorded will be saved When recording make sure you are facing the microphone and are within 30 cm infront of it O Recording Specific Alarm messages m If Rec Specific is chosen the specific alarm message selection menu is displayed for you to select the desired one Blulr g il ja Ir Mis lg Fli jr je Mis ig PA Mis g E mie ir gjen Mis g Sit jo p m Selection a specific message and follow the same procedure as those for recording Address message to record each specific message respectively The message length for each specific message is 3 sec only O Changing a message If for any reason you want to change any part of the recorded message just follow the same procedure to record a new message for that part The new message will override the previous one O Test Report Control unit allows you to test whether telephone function is working properly or not with the pre set telephone numbers Step 1 Using V or A cursors to select the test call number to test dial Press OK to confirm Step 2 Following screen will appear Dji all ji nig 2011 04 27 Step 3 Panel w
3. o O O o gt h h 2011 04 27 O Press A 8 W keys to select the option O Press OK to confirm O Siren On is set as factory default 13 Language This function is for setting the display language You can select English or Swedish The screen will show En Siw gil li isih e ld ji s h O Use A W keys to choose the language O Press OK to confirm e Default English IV Special Settings This menu is for the user to store the specialized features for CTC 1132 system Step 1 Select Spc Settings option Step 2 Press OK then the Special Settings Menu will be displayed l L y N VJ e lt er jas Q OK E 5 E 5 gt eS FS mm m m j o lo lo oO mo o Sk Is lt ojo mooo o 5 o loo o lt 5 p jo coce 0 gt K Imi lo o m h six 7S0 SF Fras o v O 3 0 TI ooreo mi lt o Iii gt gt lc ojos jo f OJO 3 0 lt NOTE gt Interference function is used in 868 Mhz frequency band Control Panel only Use A amp V to move the cursor to select the item press OK to confirm the selection displayed in front of an opt
4. e The Control Panel should not ve located alongside other radio transmitting devices such as mobile phones cordless phone or wireless computer network WiFi devices 2011 04 27 Impontant When drilling into a wall ensure that there are no hidden cables or pipes 2 Mounting the the Control Panel The Control Panel can be mounted on the wall or wherever desired Ensure the Control Panel is fitted at approximately chest height where the display can be easily seen and the keypad convenient to operate V 2 level passwords In order to provide highest security in operating the system CTC 1132 offers 2 levels of authorization That is Y Personal PIN Code v Master Code A PIN Code O There are a total of 4 User PIN Codes per each system The PIN Code is the ist level of password It has the authorization for daily operation such as Arm the system Disarm the system Enter the Home mode SS Partially arm the system By pass mode xXx Display Fault events View the Event log Power Switch O 1234 is set as default User 1 PIN Code by the factory O User PIN code 2 4 are deactivated by factory default B Master Code O The Master Code has the authorization to enter Programming mode In Programming mode the following options can be programmed v Add the device in v Edit the devices v Remove a device Y Program the External Siren CTC 1132 868AM Edit Power Switch Set Pin Code Set
5. C C 46l Press OK The next display will then show ojujnit r ly o d e Step 3 Enter a number 0 on this field Oj Step 4 Press OK and the display will automatically return to the main Program menu list e f your SIM card format is without Country Code like 0912345678 You do not have to edit Country Code Please escape this section lt NOTE gt It is recommanded that use a handy to send a Command SMS message with confirmation message see XIII Remote Control Command via SMS message on page 39 for details to remotely control the Panel for testing whether the setting is correct or not CTC 1132 868AM 26 X GSM Signal CTC 1132 utilizes GSM as its telephone interface for communication purpose The GSM signal can be monitored by selecting GSM Signal in the Programming Main Menu GS M Si ginjall Pil lelalsjle Waii It The current GSM signal strength in RSSI scale 0 9 with 9 being the highest strength value will be displayed on LCD and may change due to change of environment G S M G Sii lginja l M RSS 7 S XI Walk Test O When Walk
6. If the battery voltage of PIR sensor Door 1 Fault Message Display Contact Remote Keypad Water Sensor e When any fault situation persists the Remote Controller or Smoke Sensor is Control Panel will respond as below when low a Sensor Low Battery message will it is in Disarmed mode pe detecicd m The Yellow LED will light to indicated O Sensor out of order the fault condition After installation of the PIR sensor Door The LCD will display the type of fault Contact Water Sensor or Smoke Sensor and the source of the fault in the a periodic supervision signal will be Fault Display section of the User transmitted at intervals between 60 min Menu 19 100 min E A warning beep will sound at every If the Control Panel did not receive the 30 seconds signals transmitted from any individual Mm f a fault condition is detected while sensor for a period of preset supervision timer Hours Hours a sensor out of order fault event will be detected and displayed the system is in full arm mode the fault event display will not be generated until the system is disarmed O Interference CTC 1132 can detect interference on both 2 Clearing Fault Message Display fee Mhz And ob8 Mna ieduency band e The Yellow LED will turn off automatically After a continuous interference signal is once all of faulty conditions are restored or present for more than 30 seconds an any faulty devices are removed It cannot interference eve
7. Programming mode press this key to move the cursor and scroll the display downwards CTC 1132 868AM T G Key Programming mode use this key to delete a digit cancel the selection abort the current screen return to the previous screen etc To confirm the keyed in data or confirm the selection El Key Enter Programming menu lo gt Key Enter Installer menu 11 Buzzer 13 ON 12 15 14 12 DC jack DC 9V 500mA power adapter connection 1 2 Mounting Holes amp Tamper 14 SIM card holder cover 15 Battery Switch 16 Microphone 2011 04 27 Il Insert GSM SIM Card CTC 1132 Control Panel features built in GSM communication facility to make message reporting to the phone numbers pre programmed within the system O To Insert your SIM card The GSM component is situated inside the Power Supply compartment as pointed out by the arrow below SIMCARD O Unlock the SIM card base by sliding the cover toward OPEN backward direction O Spring open the SIM card slot and insert your new SIM card O Replace the SIM slot onto the base lightly Remember to lock the SIM card base by sliding the cover toward LOCK forward direction lt IMPORTANT NOTE gt Be aware to only insert or remove SIM card when the Control Panel is completely depleted of any power residual Please disable SIM card PIN code before it is inse
8. Se cursor to the desired item press OK to confirm the selection The display will show you the individual programming screen accordingly If a down arrow symbol V appears on the last column of the screen it indicates the selection list can be downwards scrolled If the lowest position is reached the down arrow symbol disappears If an up arrow symbol A appears on the last column of the screen it indicates the selection list can be upwards scrolled If the upper position is reached the up arrow symbol disappears Pressing G the screen will also return to Alarm Off screen After User1 2 3 amp 4 PIN codes and Master code are programmed with new numbers remember to enter the newly programmed codes when accessing Programming mode afterwards In Programming mode if no key is pressed within 5 minutes the Control Panel will automatically exit Programming mode to Alarm Off mode ll Telephone Settings In Telephone Settings menu the following parameters can be programmed at your discretion Tel Numblier s Rie jc joir d Mis g Telst Report CTC 1132 868AM 1 Telephone Numbers e In Tel Setting menu select Tel Numbers the screen allows you to set change delete the emergency telephone numbers O A maximum of six numbers can be stored in priority order
9. keys to switch Press OK to confirm 20 sec is set as factory default lt NOTE gt Full Arm Entry time applies only to the zone that a Door Contact or PIR CTC 1132 868AM 12 Detector is installed and is set to Entry f incorrect PIN code is entered and or the entry delay time has expired then the system will trigger the Burglar alarm 6 A Exit Time This is for you to select the Exit Delay time when Full Arming Options available are O sec 10 sec 20 sec up to 70 sec in 10 sec increments A E x i lt T i me 3 0 sjejc A V O K O Use A V keys to switch between options O Press OK to confirm O 30sec is set as factory default lt NOTE gt Full Arm Exit time applies only to the zone that a Door Contact or PIR Detector is installed and is set to Entry If incorrect PIN code is entered and or the Exit delay time has expired then the system will trigger the Burglar alarm 7 H Entry Time This is for you to select the Entry Delay time when Home Arming Options available are 0 sec 10 sec 20 sec up to 70 sec in 10 sec increments Tli me AVIO Entir y 2 0 sell K Use A w options keys to switch between Press OK to confirm 20 sec is set as factory default lt NOTE gt
10. _JAJL A R M e When you come back and disarm the system by pressing the DISARM button on the Remote controller the Alarm warning display still remains unchanged e To clear the display follow the same steps as Stopping the Alarm described above you can see the source of the alarm f more than one alarm events including Device Tampered have occurred repeated pressing further keys the alarm events will be displayed one by one sequentially until all events have been displayed then the screen returns to Alarm off IX Event Log The alarm log memorises the last 20 system events including Y All Alarm Events with Device ID Y All Fault Warning Events Y All Arming And Disarming Events Y Remote Control Event CTC 1132 868AM 34 The logged events are displayed in reversed chorological order most recent event first The log is marked with a Start label before the most recent entry and End after the oldest entry To View Log Step 1 Key in the user code and press OK while in Disarm mode to access User s Menu Step 2 Press the W key repeatedly to select Log and then press OK and the start of the log will be displayed S T A RT 0 8 10 2 1 6 D Je lc Step 3 The log can now be scrolled up and down and view
11. 2011 04 27 O Press OK to confirm e Entry Snd On Entry Sound On is set as factory default 4 H Exit Sound This is for you to decide whether the Control Panel will sound short beeps during the Exit Delay period when Home Arming Exji It E x i it S In ld Sind O O n ff Press A amp V keys to select the option Press OK to confirm Exit Snd On Exit sound On is set as factory default 5 H Entry Sound This is for you to decide whether the Control Panel will sound short beeps during the Entry Delay Period when Home Arming Einit r jy Snid On Ejnjt jr jy Sinid Off f O Press A amp V keys to select the option O Press OK to confirm e Entry Snd On Entry Sound On is set as factory default 6 Siren Delay This is for you to decide how long should the Control Panel suppress all audible alarms after an Burglar alarm is reported Options are OFF and 1 min delay to 10 min delay in increments of 1 minute O Press OK to confirm e Off is set as factory default 7 Verification Turn on and off the Sequential Verification Reporting Vie lr ji f Viel ji f Of If Ojn Sle q Sie q O Press A amp Y k
12. Home Arm Entry Delay time applies only to the zone that a Door Contact or PIR Detector is installed and is set 2011 04 27 to Entry If incorrect PIN code is entered and or the entry delay time has expired then the system will trigger the Burglar alarm 8 H Exit Time This is for you to select the Exit Delay time when Home Arming Options available are 0 sec 10 sec 20 sec up to 70 sec in 10 sec increments H E x ji lt Tli m 300 sec JA lt o OIK O Use A Y keys to switch between options O Press OK to confirm O 30sec is set as factory default lt NOTE gt Home Arm Exit Delay time applies only to the zone that a Door Contact or PIR Detector is installed and is set to Entry If incorrect PIN code is entered and or the Exit delay time is expired then the system will trigger the Burglar alarm 9 Door Chime This is for you to decide whether the Control Panel will sound a Door Chime if the Door Contact or PIR Detector is activated at the Entry Point while the system is in Disarmed mode Dolo ir Chi Dolol r Cih ii e On e Olf f m m O Press A W keys to select the option followed by appearing next to the selected option O Press OK to confirm e Door Chime Off is set as factory default
13. lt NOTE gt When Door Chime is disabled there will be no door chime when Entry point DC or PIR is triggered at Disarmed mode CTC 1132 868AM When Door Chime is enabled the system will make a Ding Dong sound to inform user that a DC or PIR at Entry Point is triggered at Disarmed mode 10 Time This is for you to program the current time to be displayed hour amp minute Tli me Set t ji n g 0 0 O 0 AWO K O Hour flashes first use A Y keys to choose a correct number for the current hour Hours are indicated by 00 23 O Press OK to confirm Next the screen will be displayed for you to set the correct minute O Minutes are then flashing O Use A W keys to choose a correct number O Press OK to confirm 11 Date This is for you to set the current date Daljte Silet ti inig 1 5 Jja n AWOK O Months flash first use A W keys to choose the current Month O Press OK to confirm Next the screen will be displayed for you to set the current day O Days are then flashing O Use day A Y keys to choose the correct O Press OK to confirm 12 Panel Siren This is for you to decide to enable or disable the Control Panel built in Siren when there is an alarm event Sli sii
14. while the Alarm off is displayed a Enter Code promp screen will be displayed After you enter your pin Code the above screen will also be displayed After 30 seconds of key inactivity the system will automatically exit User Menu and return to Alarm off mode II Away Alarm ON Mode 1 Arming the system If the system is in Disarmed mode Alarm off to arm the system Step 1 Enter your PIN code and press OK The display will show Ww y Ajr im e Ar im a s s vr oI D gt olo xio AAEE elr siwi It icih and the cursor stays at Away Arm 2011 04 27 Step 2 Press OK and the screen will display Ti To jE x i it 3 0 sle c me The defined EXIT Delay is displayed on the second line and is counting down During the EXIT Delay period the exit sound plays unless it has been chosen to switch off Step 3 When the Exit Delay time is up or the Entry Door Contact Final Door Set Function programmed to be On is closed the Control Panel will sound a long beep The Alarm On will display on the screen and the system is in Arm mode All lair jm O 0 7 25 11 N 6 lt NOTE gt When Final Door Set Option is set to Off the Control Panel ent
15. 53101 51199 3 Power Switch Open for 1 Hour to 99 Hours 54101 51199 4 Power Switch Open for 1 Hour to 99 Hours 55101 51199 5th Power Switch Open for 1 Hour to 99 Hours 56101 51109 6 Power Switch Open for 1 Hour to 99 Hours 57101 51109 7 Power Switch Open for 1 Hour to 99 Hours 58101 51199 8 Power Switch Open for 1 Hour to 99 Hours lt NOTE gt digit Control Command Format Cc Cc Cc D D The Number of Open period the Power switch for hour CCC The Number of the Power switch E g 511 is the 1 Power switch 521 is the 2 Power switch DD Open period for hour 01 is Power switch open for one hour 99 is Power switch open for 99 hours NOTE Enter a space between each command Ifyou set the open period for 2 hours it means when the Panel receives the command the power switch will turn on for 2 hours and turn off after 2 hours 2011 04 27 lt EXAMPLE gt e Send the SMS message to command the Unit to turn off the Power switch 2 without a confirmation SMS back to your mobile phone The format is A For 2 digit Remote Control Command e Send the SMS message to command the Unit to enter Arm Mode and send a confirmation SMS back to your mobile J O E 123415 ll phone The format is MICHAEL 112314 1 1 ol o The programmed SMS User PIN Power switch keyword Code Number The
16. 80 seconds the Control Panel will then consider the call as unsuccessful and will try to dial the next phone number in priority If more than one number is programmed the Control Panel will continue to dial the number s until two emergency calls are successfully answered with either keys or 0 or closed down with a key 9 acknowledgement CTC 1132 Auto Dialling features only operate under Tone Dialling method Call Acknowledgment If the recipient successfully receives the call the recipient should acknowledge it by pressing the DTMF 0 or 9 button on the telephone set Acknowledging with signal 1 The recipient can press 1 to acknowledge the call and also initiate a One Way Listen In Channel for 2 minutes This channel allows the recipient to listen in to what is happening to the other side of the line During the Listen in period the CTC 1132 will sound one audible beep via the CTC 1132 868AM 41 telephone handset signaling 20 secs time remaining alerts to the call Recipient Press DTMF 1 can extend another 2 mins If the Listen in period expires without DTMF command press the call will automatically hang up Acknowledging with signal_0 If the recipient presses 0 on the phone set as the acknowledging signal The Control Panel will take the following actions Y The Control Panel will go back on hook Y The Control Panel will continue alarming Y The Control Panel will try t
17. All 4 User PIN code can be edited freely by the following steps Step 1 Move the cursor to the item Pin Code then press OK the following screen will show the status of each User PIN code S TH M l IMJR S SMI T H kk K k K Je Je Je Jeje le Step 2 Move the cursor to the desired 2 4 of programmed user PIN code to be deactivated deleted then press OK the following screen is displayed x0 S R R x AION Die l le t e Pli n Cjo dje Ojk Step 3 Press G key the next screen will ask you to enter your new PIN code and repeat it for double confirmation Step 4 Follow the same steps as described in Set your own pin code to edit 2 Temporary Code e The Temporary Code is used to arm disarm the system for a temporary user and is valid only once per Arming and once per Disarming Afterwards the Temporary Code is automatically erased and needs to be reset for a new Temporary user The Temp Code consists of 4 digits and is not activated as default by the factory To Set Temporary Code Step 1 Use the arrow keys to select Temp Code and press OK Elnit je lr Nie w Clio d e 2011 04 27 Step 2 You can key in your preferred 4 digit number an
18. Panel Tamper Interference Detection GSM isn t ready GSM PUK GSM PIN Code SOS SS O Incase any fault condition is detected the Control Panel will respond with a Fault display and or Fault alarm respectively according to the nature of the faulty event O Device Sabotaged m The Control panel Door Contact Remote Keypad PIR sensors are Tamper protected Control Panel A Tamper switch protects CTC 1132 from any removal attempts away from its cross mounting bracket 2011 04 27 Another Tamper switch protects the Panel SIM Card Power Supply Lid from being opened This indicates that you need to insert or removed the GSM SIM Card Please refer to PIR Sensor Page 16 IV Special Settings eo ForIR 7 amp 8 Section 14 A Tamper switch protects the Panel GSM PIN Code enclosure from being opened You will need to set up your own PIN code e ForIR 9 Panel GSM Signal Please change the position of CTC 1132 control panel to get better GSM signal Panel GSM Fault Please re start your CTC 1132 A Tamper switch protects the enclosure from being opened A Back Tamper protects the unit from being removed from its mounting site Door Contact control panel A Tamper switch protects the gt enclosure from either being opened gt Panel GSM PUR or being removed from the mounting SIM Card has been locked please surface call your service provider for help O Sensor Low battery
19. Step 3 Press OK and the screen will display Ti To jE x i it 3 0 sle c me The defined EXIT Delay is displayed on the second line and is counting down During the EXIT Delay period the exit sound plays unless it has been chosen to switch off Step 4 When the Exit Delay time is up the Control Panel will sound a long beep The Home will display on the screen and the system is in Home Arm mode lt NOTE gt The system can also be armed by using the Remote controller Optional Step 5 Press OK and the screen will display Ho imie 0 81 00 1116 Die lc 2 Stopping the Exit Delay The Exit Delay can be stopped following the steps described in Stopping the Exit Delay in section Il Away Mode 3 Extend the Exit Delay The Exit Delay can be extended following the steps described in Extend the Exit Delay in section Il Away Mode 4 Forced Arming O if there is any fault condition has occurred or a door was found opened before or any sensor is triggered when you press OK in step 3 above or when you press Home button on the Remote Controller the Control Panel will sound a ding dong warning sound to indicate entering the Home mode is prohibited You rectify the problem first then clear the fault display and then try again Or you can
20. Temporary Code Set Duress Code Set Master Code Set Telephone Numbers Set Messages Set SMS related Features Select Walk Test mode GSM signal Y SMS Keyword O 1111 is set as default Master Code by the factory GX KN KN SN SN SN SN SN SOS lt NOTE gt 5 No any two codes can be the same if so the message Code in use Select another will be displayed to prompt the user to choose differently VI Getting Started Step 1 Find a suitable location for the Control Panel to be installed Step 2 Apply the AC Power You will hear a long beep Alarm Or will be displayed on the first line and 00 01 01 Jan displayed on the second line of the screen indicating the system is in Away mode this is the default mode Step 3 Press 1 key on the keypad the display will show Ejnit lelr C Step 4 Key in the remaining 234 default User1PIN code 1234 within 30 sec Step 5 Press OK You will hear 2 short beeps and the display will show Alarm Off 00 0 1 01 Jian The system is now in Disarmed mode 2011 04 27 lt NOTE gt In Step 4 press G cancel key will clear one previously entered code OK key confirming the entered PIN code should be pressed within 30 sec Otherwise the display will go back to Alarm On and the syst
21. Test is selected the Green amp Yellow LED s will flash 3 times with 3 beeps and the following two test patterns are displayed for 2 sec each CN Then the following message is displayed Wa ll k Tle s it i O Pressing the test button on the sensor or any button on the Remote Controller or triggering the sensor if the Control Panel received the signal it will sound 2 short beeps and the display will show you which sensor with its zone number is reacting and the RSSI strength R l Zioinie 0 2 Hall wia ly D R 0 9 The message will be displayed for 30 sec or being replaced by another test signal Pressing G key the screen will return to Walk Test banner 2011 04 27 lt NOTE gt The function of showing its RSSI strength e g R 09 is only avaliabe in 868 MHZ Control Panels Exit Walk Test eo To exit Walk press G key Test mode O If no test signals are received for 5 minutes the Control Panel will exit Walk Test mode and return to Alarm Off Press OK key to add another 5 minutes XII Reset GSM GSM module will be reset once you have press OK Please wait for 1 minute for the reset process to be activated Operation Entering User Menu When the system is in Disar
22. User Remote Confirmed programmed PIN Control SMS keyword Code Command C For 5 digit Remote Control Command lt NOTE gt Send the SMS message to command A confirmation SMS message will read the Unit to turn on the Power switch on your mobile phone as 2 for 1 Hour and than turn off and send a confirmation SMS back to your Confirmed MICHAEL 1234 11 00 mobile phone The format is Send the SMS message to command JO E 112345 2 1101 lo Io the Unit to enter Arm Mode without a confirmation SMS back to your mobile The User Power Time Confirmed phone The format is programmed PIN switch SMS Code Number MICHAEL 1 23 14 1 1 keyword The User Remote programmed PIN Control lt NOTE gt SMS keyword Code Command A confirmation SMS message will read on your mobile phone as Confirmed Joe 1234 52101 00 B For 3 digit Remote Control Command e Send the SMS message to command The 3 digit Remote Control Command is the Unit to turn on the Power switch used for turning off the Power switch 2 for 1 Hour and than turn off without a confirmation SMS back to your mobile e Send the SMS message to command phone The format is the U
23. and Emergency according to the nature of the alarm raised O Recording the messages When the Record Msg is selected the following Recording Selection menu is displayed for you to select which part of the message is to be recorded Rie lc Ad d ir le s s h Oo Rie c S p fe tc ji S lt o p O Recording Address message Step 1 Move the cursor to select Rec Address and then press OK the screen will ask you to confirm Cihja nigje Ald id rje s s Mjs g O k Step 2 Press G to abort Or press OK to confirm A prompt Message will be displayed for 2 sec Sit jar jt Recjoridi inig Aff jt jejr the Bele p Step 3 After 2 sec the Control Panel will sound a long beep the following prompt message will be displayed and recording can be started INjo wl Relcjo r idli jnig Enjid wit h Ok Step 4 Press OK to end the message the screen will go to Specific Part Selection menu to allow you to select a specific part to be recorded lt NOTE gt To end recoridng at any time press G and the message will be saved as it is The screen returns to Recording CTC 1132 868AM Selection menu
24. be reported When the system is in Armed mode and the Control Panel is counting down the Entry Delay if a Burglar Door Contact is triggered the Control Panel will not respond During the Exit Delay period if a Burglar Door Contact is triggered the Control Panel will not respond O for Home Omit Door Contact When the system is in Home mode if a Home Omit Door Contact is triggered the Control Panel will not respond When the system is in Full Arm mode if a Home Omit Door Contact is triggered the Control Panel will respond in the same way as if a Burglar Door Contact is triggered A for Home Access Door Contact When the Door Contact has been set to Home Access and triggered when the system is in Arm mode the Control Panel will start a Burglar Alarm and be reported When the system is in Home mode if a Home Access Door Contact is triggered the Control Panel will start an Entry Delay period to give enough time to disarm the system However during the Entry Delay or Exit Delay period if a Home Access Door Contact is triggered the Control Panel will not respond 2011 04 27 D for Delay Door Contact e When the system is in Arm mode if a Delay Door Contact is triggered first a Burglar Alarm will be generated immediately However during the Entry Delay or Exit Delay period if a Delay Door Contact is triggere
25. for Personal Attack Remote Controller Control Panel will give a Personal Attack alarm when the panic button is pressed for 3 seconds long or twice within 3 seconds M for Medical Emergency Remote Controller Control Panel will give a Medical Emergency alarm when the panic button is pressed for 3 seconds long or twice within 3 seconds StepC8 Use the W A to make your selection and confirm by pressing OK The next display will prompt you to give a name or location description to the device to help understand system events You can enter up to 10 letters as you please for the name StepC9 Or simply press OK for no name Please see section Device Naming for details Elnit je lr N a me O StepC10 Press OK when finished and the display will show the new zone name next to the device all oK RJ S st M n Cc eld MI TH l R StepC11 Press OK adding a RC is now completed screen returns to the Device menu lt NOTE gt After a Remote Controller is added in you can use the Remote Controller to arm disarm the system In addition pressing the Panic button for 3 seconds or twice within 3 seconds the Control Panel will generate a Panic alarm The Panic alarm generated from the Remote Contr
26. in the order of A B to F A B to F represent the priority number of the six tel numbers respectively If the tel number for a particular priority number has not been stored three dots are displayed indicating the memory spot is empty Only 11 digits can be displayed on the tel Numbers list Non fitting numbers are indicated with after the incomplete number O Store Tel Numbers Step 1 Step 2 Step 3 Step 4 Move the curser to the Tel Number submenu and press OK The display will show the following screen when no tel number has been entered TIMO Choose from A to F sets to store your phone number Then press OK The phone number A must be entered or the Panel will not dial out at the Alarm situation The following screen will be shown for you to enter the phone number Elnit le lr nie w No OK Key in your phone number Press OK 2011 04 27 The screen will then prompt you to choose o o Mio Rie plo rr it SMS re pio gt Voice Reporting For an alarm event the reporitng is done via playing voice messages Available ones are Burglar Medical Emergency Fire and Panic to the phone numbers programmed at this step SMS Reporti
27. press G to exit to the previous device list Step3B Edit the zone name and press OK when completed and return to the previous device list Step4B Proceed to edit other devices or Press G to return to Add Delete Device menu 3 Remove Devices Adding a device a second time is prohibited unless it is removed from the system first To delete a device choose Remove Device in the Device menu Step 1 Use A W keys to scroll the display All the used zones with the device names are listed in order of the zone numbers DIC Blalcikid o o ir LIR Hall w a ly RIC IMIR ISIMI TH SD Ki t icihiejn Step 2 Press OK when the required device is chosen The following prompt message will be displayed for you to reconfirm Re molve Ojk RC MR SIMII T H Step 3 Press OK Deleting a device is now completed The screen returns to previous device list lt NOTE gt f the selected sensor zone is not what you want to delete press G to exit the device list is again displayed for you to make another selection f Remove Device menu is chosen while no device has been installed the display will show No device found in system for 2 sec and return to the Device menu Step4 Proceed to remove ot
28. that the device is in learn mode and repeat the steps again After they are added in every time pressing a PIN code amp followed by OK key will result in the Control Panel transmitting signal to all of them CTC 1132 868AM 23 lfthere is no other detector or Remote Controller being added first the following message will be displayed in Step 3 PII le ja s le a d id o ne die lv lic le The message will be displayed for 2 sec then the screen returns to Device menu You are requested to add a detector or Remote Controller first then you can try programming these auxiliary devices again lt IMPORTANT NOTE gt For the following options whichever option is selected when the Control Panel transmits the signal all added sirens will simultaneously received the signal and all will acted accordingly Siren Tamp On Siren Tamp Off The Outdoor Siren BX 8 tamper switch can be enabled and disabled remotely This is used especially when replacing siren battery e Disable the Siren tamper switch by selecting Siren Tamp Off and press OK All added sirens will temporarity lose their Tamper Protection simultanously Enable the Siren tamper switch by selecting Siren Tamp On and press OK All added sirens will be enabled with the Tamper protection simultanously lt NOTE gt The Siren tamper disa
29. user pin code user 1 user 4 If the pin code is correct you will hear 2 beeps from the Control Panel via phone set Step 5 2011 04 27 lt NOTE gt In Step 5 the first digit of pin code should be entered within 3 sec In Step 5 a valid pin code should be entered with 20 sec otherwise the Panel will hang up automatically Step 6 Enter the 2 digit DTMF Control Command When the Command is correct you will hear 2 beeps if the Command is uncorrect you will hear 1 beep For DTMF control commands must the GSM signal be good if not use SMS e DTMF Remote Control Command Table Control Command Result 00 Hang up the phone 01 Listen in 10 Disarm 11 Arm 20 UR 1 deactivate 21 UR 1 activate 30 UR 2 deactivate 31 UR 2 activate B Via SMS message SMS Remote Control Command Table Control Command Result 00 Hang up with Confirmation 10 Disarm 11 Arm 20 UR 1 deactivate 21 UR 1 activate 30 UR 2 deactivate 31 UR 2 activate CTC 1132 868AM 39 510 1 Power Switch Close 520 2 Power Switch Close 530 3 Power Switch Close 540 4 Power Switch Close 550 5 Power Switch Close 560 6 Power Switch Close 570 7 Power Switch Close 580 8 Power Switch Close 51101 51199 1 Power Switch Open for 1 Hour to 99 Hours 52101 51199 2nd Power Switch Open for 1 Hour to 99 Hours
30. 2 Key in 1234 default User1 PIN code within 30 sec Then press OK The screen will prompt you to enter the Master PIN code P M M dle Einit efr oldie Ojo lt NOTE gt During keying in the PIN code press G will clear one previously entered code If the code field is empty press G the screen will exit and return to Alarm Off screen Step 3 Key in 1111 default Master Code within 30 sec Step 4 Press OK The following message is displayed for 2 sec Piriogirjalm Me nju Mia kle la Sel jejc jt ji jojn Step 5 Then the Programming Main menu will be displayed o Wall k Tle s t Tle l Sje jt t ji jnig v lt NOTE gt The cursor is indicated by a flashing dot on the left upper corner It can be move up amp down by pressing A amp Y key respectively Step 6 Press A Y keys to move the cursor downward or upward The screen is also scrolled down or up respectively The following items can be selected v Walk Test Y Tel Setting Y Gen Settings Y Spe Settings Y Devices 2011 04 27 SMS Editor SMS Keyword Country Code GSM Signal Reset GSM Sy Oe A Step 7 After making a selection by moving the lt NOTE gt
31. 868MHz Home Prosafe 1132 GSM CTC 1132 GB User manual Art 36 2868 Nelectia Table of Contents Application OvVervieW ococccococccnccoccononcnncno rn nncn nora i Identifying the DATES A i Ae A ee AE 1 Insert GSM SIM Card nario did 2 lll The power SUPPLY sia ies cag ato in rd is 2 IV How to install the Control Panel ooooooococccccccccnconccnonancononcnnanconcnncnannonnnnnnnnnnnnnconcnnnnanceninnnnininoss 2 Ni 2 level PASS WOTAS iii a ii tad dado 3 ViGetting Starteds isn datea a ts 3 Configuring Your SySteM oococococococconononononononnnnononononononos 4 I Entering programming MOAE ooccoccccncoconcnconcncnncononnnnnnconnncnnnncnnnnnnnannnnnnnrnnnanrrnrnnrnarnnnrnnrninninss 4 Il Telephone Setting S moiseen eeni te eaaa a aa priae E iaeaea aeai 5 lll General Settings iaa A A cee A 8 V Special Settings inina aa AA DAA A 14 Vi Add Delete Device cid oca 17 VI SMS Ed O k ee a ida ada dida dial 25 VSMS KeyWord iii e dla ito 25 X County Code iia ia 25 AGS MISION I id EEA A A AST 26 Al Walk Testi A Ad eed 26 XI Reset OS Mistral A A dateneee eee 27 Operacional 27 Entering User Meni eane verde uhete shawaedeersateysbataees grec dee thas a Ee AATE AAE AEE a 27 Il Away Alarm On Mode 0ccceeeee eee nee eee eee ee eee eee eee een eee eeeeaee eee eaa ees 27 WhIFORESRANMIING is area ira ce an os oa loe A 28 IV Disarm Alarm off MOde oooocccccccccoconcnconincononnnnnnnoncononnnconnnconnnninnnrn
32. arning code the position CTC 1132 868AM to UR 2 simultaneously The UR status LED lights up for 3 seconds Step 8 Remember to put these Universal Receivers out of Learn mode Adding them into the system is completed 5 Edit Power Switch The controlpanel and power switch communicate with each other by following steps Step 1 Put the Power Switch in learning mode Step2 Put the Control Panel into programming menu Step 3 Select Device and then Program PSS powerswitch then the following screen will be displayed OOO OOO SEETEJEJEJEJE w V V V V V V V 3 3 3 3 3 3 3 5 3 3 3 3 3 3 53 5 Oooo INIO 01 AOIN Step 4 Select the disired channel number and press OK Step 5 The control panel will sound one beep and send a signal to the Power Switch Step 6 Repeat Step 4 to learn other channels lt NOTE gt When the first Channel 1 Power Switch has been set and alarm is triggered the LED of the first Power Switch will flash 2 sec On amp 2 sec Off automatically until the Control Panel is disarmed ss Ifthe AC Fault exists in the Control Panel and the alarm is trigger the LED of first Channel 1 Power Switch will flash slowly 2 sec On amp 6 sec Off 2011 04 27 Only the first Channel 1 Power Switch can flash during the panel alarm VI SMS Editor For sending a SMS alarm reporting to your mobile pho
33. ble will automatically revert to On after about an hour if not switched back 2011 04 27 O Confirm On Confirm Off Both the Outdoor Siren BX 8 can be enabled for arming and disarming confirmation where beeps are emitted from the Siren to validate that the system has been armed and disarmed Disable the Siren Confirmation by selecting Confirmation Off and press OK Enable the Siren Confirmation by selecting Confirmation On and press OK O Entry Snd On Entry Snd Off The Outdoor Siren BX 8 can be enabled or disabled from sounding the Entry Delay warning beeps Disable the Siren Entry Sound by selecting Entry Snd Off and press OK Enable the Siren Entry Sound by selecting Entry Snd On and press OK O Receiver 1 Receiver 2 2 additional Universal Receivers can be added to the system Step 1 Put Universal Receivers into learn mode Refer to their individual Operational Manual Step 2 Move the cursor to the position Receiver 1 Step 3 Press OK Step 4 The Control Panel will then sound a long beep and transmit Learning code to UR 1 simultaneously The UR status LED lights up for 3 seconds lt NOTE gt If Receiver 2 is also to be added to the system proceed to the following steps Step 5 Move the cursor to Receiver 2 Step 6 Press OK Step 7 The Control Panel will then sound a long beep and transmit Le
34. d the Control Panel does not respond E for Entry Door Contact If the Door Contact has been set to Entry and triggered when the system is in Arm mode the Control Panel will start an entry period to give enough time to disarm the system After the delay period has expired and no correct PIN code entered the Control Panel will respond with a Burglar Alarm and be reported If the Door Contact has been set to Entry and triggered when the system is in Disarmed mode the Control Panel will make a ding dong Door Chime sound if programmed H for 24 Hour Door Contact The 24 Hour Door Contact is active all the time and does not have to be armed or disarmed F for Fire Door Contact O The Fire Door Contact is active all the time and does not have to be armed or disarmed M for Medical Emgenercy Door Contact O A Medical Emg Door Contact is active all the time and does not have to be armed or disarmed W for Water Door Contact O Water Door Contact acts as an Universal Transmitter and have a Water leakage sensor connected to it The Water Door Contact is active all the time and does not have to be armed or disarmed CTC 1132 868AM 19 StepA8 Use the W A to make your selection and confirm by pressing OK You are now invited to give a name or location description to the device to help understand sy
35. d then press OK Rie pjeja t Ne w Clo d le Step 3 You are prompted to re enter the same code again and press OK If the code is correct the screen changes to the following lt NOTE gt There is no User Naming feature for Temp Code To Delete Temp Code After the Temp Code is programmed it can be deleted by following the steps below Step 1 Move the cursor to the item Temp Code then press OK Dell le t je Pi in Cioldie Ok Step 2 Press OK and the screen returns to Gen Settings Menu e To Edit Temp Code After the Temp Code is programmed it can be edited by following the steps below Step 1 Move the cursor to the item Temp Code then press OK Dell le t je Pi in Coldie Ok Step 2 Press G key the next screen will ask you to enter your new Temp code and repeat it for double confirmation Step 3 Press OK The screen returns to General Setting menu editing the Temporary code is now completed 3 Duress Code Duress Code can arm disarm the system When this code is used for accessing the system the Control Panel will report a secret alarm message without sounding the siren to the Call recipient to indicate of a Du
36. do forced arming to enter Home mode compulsorily CTC 1132 868AM 30 Please follow the instructions described in Forced Arming in Section Ill VI Partial By pass Arm Mode The Partial By pass Arm mode allows the user to de activate by pass any sensors at their discretion This feature allows your home to be armed yet the person inside the house can move freely in the area where the sensor is by passed To put the system into the Partial By pass Arm mode Step 1 Enter your PIN code and press OK within 10 seconds The display will show A wialy Ar m Hjo mie Ar im Bly p ja s is Step 2 Press VW to move the cursor down to select Bypass Step 3 Press OK Step 4 All the zones are listed in zone number order DIC Blalckd ojo tr IR Hal jl wa ly DC Fir jojn t dio o r IR Liiviinigr jojojm RIC MR SMI TH Stop Step 5 Press W A keys to select the zone to be by passed B y plals s Oik DC Balcikdio jo ir Step 6 Press OK to confirm the selection The selected zone will be marked with a x character in front of it to indicate that device is to be by passed lt NOTE gt The zones can be toggled between by passed and not by pass
37. e can be viewed on LCD under Fault Display Sensor Sabotaged 9 l the Tamper switch on the PIR Sensor or Door Contact is triggered while the system is in Arm amp Home mode the Control Panel will sound an audible alarm and report Burglary alarm While if the system is in Disarm mode no alarm will be generated E Sensor out of order The PIR Sensor Door Contact Water Sensor and Smoke Detector will send supervised signal to the Panel at intervals between 60 100 min The system will according to the setting of the supervision send report 2011 04 27 When the Control Panel cannot receive the supervised signal from the device for preset supervisory period the Control Panel will sound an audible alarm and yellow LED will light while this fault message can be viewed on LCD under Fault Display lt NOTE gt The supervision function activates in Arm Home Disarm Mode For Setting Supervision please refer to IV Special Setting 13 Supervision While the system is in Disarmed mode no alarm event will be generated E Interference When the system is programmed with Interference Detection On and when there is an_ interference detected for 30 seconds the yellow LED will light up and the fault message can be viewed under the Fault Display 5 Fault Message Nomenclature O The fault event message is displayed in short form as below Fault Condition Message disp
38. e fault event will be cleared and the screen returns to Alarm off In Step 6 if G key is pressed the screen returns to Alarm off and the Yellow LED stays on the Control Panel keeps sounding a short beep every 30 seconds and the fault event display retains If the fault condition has not been rectified the fault event display will not be cleared It will come on again while you try to arm the system and the faulty condition inhibits the system from being armed the fault message will be displayed again The fault event display can be cleared only after the fault condition has been rectified Even when the fault messgae is cleared the fault event will still retained in the Log CTC 1132 868AM 37 E AC Power Fail Only the yellow LED will light and the fault message will be displayed no further action will be taken E Control Panel Low Battery Any time the Panel battery Low is detected yellow LED will light while this fault message can be viewed on LCD under Fault Display E Panel Sabotaged Ifthe Tamper switch on the Control Panel is triggered while the system is in Armed and or Home mode the Control Panel will sound an audible alarm and report Burglary alarm While if the system is in Disarm mode no alarm will be generated E Sensor Low Battery Ifthe low battery is detected on any sensor yellow LED will light up at any time while its fault messag
39. ed by pressing the OK key repeatedly followed by the x character appearing for By pass setting and xk character disappearing for By pass unsetting 2011 04 27 Step 7 You can repeat Step 5 Step 6 to continue selecting the device to be by passed Step 8 After all the sensors to be by passed have been selected press G to return to user menu and the cursor stays at Arm Step 9 Press OK to select Arm and to arm the system lt NOTE gt f a sensor is by passed then the Contorl Panel will not respond to its triggering in Arm mode The by pass setting is effective for only one time once the system is disarmed the by pass setting is cleared automatically When a sensor is by passed the system can be armed directly regardless of its fault situation if any However its fault situation is still being monitored and will be logged and displayed when you access the Log submenu CTC 1132 868AM 31 2011 04 27 VII Alarm Activation For Alarm Activation by Events and Control Panel Responses please refer to the following table Control Panel Mode amp Response Table CTC 1132 868AM Response No Response No Response No Response No Response Burglar Alarm Emergency Alarm Fire Alarm Instant Burglar Alarm Instant Burglar Alarm Instant Burglar Alarm Start Entry Timer Instant Burglar Alarm Burglar Alarm Emerg
40. ed with the A W keys the most recent event will be at the start Step 4 An example of logged event is given below where the first line tells the time and date of the event the second line tells the type of event and the third line either states the User or the device that caused the event Abbreviation as DC stands for Door Contact LB is short for low battery Tamp means Tamper where Rest is short for restore 0 2 38 0 1 JJ ja jn Dli s la lr m Uls eir 1 02 140 0 2 Jain Planli c DIA V iI D RIC X Power Switch Step 1 Select Control PSS Powerswitch and then the following screen will be displayed 0 OOOO SSEJEJEJEJEJEJES w v iv v v v v 515 5 5 5 5 5 5 515 5 5 5 5 5 5 ojololojolojojo oO A oN e 2011 04 27 Step 2 Select the desired Power Switch Channel number and then press OK Ojn Of If Tlulr jn Turin lf the user choose to Turn On the power switch then power switch will automatically power on and activated On the other hand if the user choose Turn off then power switch will be power off and deactivated The user can set any of those eight power switch freely according to their own need lt NOTE gt When the use
41. em remains armed During entering PIN code if more than 20 keys including OK amp G key were pressed without a valid PIN code strings it will inhibit further key presses for 1 minute In Step3 if you press a key other than numeric keys the display will remain the same requesting you to key in 1234 default PIN code and then press OK The Control Panel has Screen Save function The Alarm off message will be displayed for 160 sec only Afterwards only current date amp time is displayed on the second row line Step 6 Please wait for 2 to 3 minutes for the system to read it status Then if the yellow LED turns on it indicates that there is a fault Press 1234 to enter the user menu within 30 sec Step 7 Press OK and the display will show Fiajull jt Disip Awaly Ajr m Hoime Air jm By p a s s Lolg Piojwie r Siwii jt ch Step 8 Choose Fault Dsp and press OK The following possible Fault will display Configuring your system I Entering Programming mode If the system is in Disarmed Alarm off mode to enter the Programming mode follow the steps below Step 1 Press key The screen will prompt you to enter CTC 1132 868AM the User1 PIN code P Mio dje Ejn tieir P Code Step
42. ency Alarm Fire Alarm Water Alarm Instant Burglar Alarm No Response Start Entry Timer Start Entry Timer Instant Burglar Alarm Burglar Alarm Emergency Alarm Fire Alarm Water Alarm 32 Response No Response No Response No Response No Response Burglar Alarm Emergency Alarm Fire Alarm Water Alarm Response No Response No Response No Response No Response Burglar Alarm Emergency Alarm Fire Alarm Water Alarm No Response No Response No Response No Response No Response Burglar Alarm Emergency Alarm Fire Alarm Water Alarm 2011 04 27 VIII Stop the Alarm and Alarm Display During any alarm the Control Panel wil sound its siren and report to the Phone number programmed previously The display will show as below ALJARM ALARM AJL A R M AJL 1 Stopping the Alarm During an alarm to stop the siren and clear display Step 1 Key in your PIN code followed by OK lt NOTE gt If you press any key other than the first digit of your PIN code the screen will prompt you to enter your PIN code Step 2 If the PIN code is correct then the alarm sounding will be stopped If the alarm is stopped before reporting process begins Step 3A The screen will show you which device that triggered the alarm with its zone number di
43. ers Alarm On mode only when the Exit Delay time is up The Control Panel has Screen Save function The Alarm on message will be displayed for 160 sec only Afterwards only current date amp time is displayed on the second line The system can also be armed by using the Remote controller Optional 2 Stopping the Exit Delay The Exit Delay can be stopped by disarming the system Step 1 Press G Step 2 The screen will ask you to enter the PIN code In addition the counting down Exit Delay is displayed on the left side of the 2 line Enter your PIN code and then press OK Alarm Off will be displayed on the screen and the system returns to Disarmed mode Step 3 lt NOTE gt The Exit Delay can also be stopped by pressing the Disarm button on the Remote Controller Optional CTC 1132 868AM 28 If the Exit Delay period times out before the code can be entered the system will be armed 3 Extend the Exit Delay During the Exit Delay period the delay time can be extended by pressing the ARM button on the Remote Controller Optional Each time the ARM button is pressed the delay time starts counting from the beginning To do this press and hold th ARM button for 1 second and you will hear a long beep to confirm the extention of Exit time lt NOTE gt While you arm the system if a Door Contact or PIR sensor has been trig
44. eys to select the option O Press OK to confirm O Seq Verif Off Sequential Verification Off is set as factory default lt NOTE gt For detailed description of this feature please refer to Sec X False Alarm Management of Configuring your system 8 Final Door Turn on and off the Final Door Set Option Of If Ojn Dio lo r Dio lo r Fli nlal Fli nlall O Press A 8 W keys to select the option O Press OK to confirm e FinalDoor On Final Door Set Option On is set as factory default lt NOTE gt Of f 1 Mi ini 2 Mi ni 3 Mi in 4 Mi ni to 10 Mi jn O Press A amp W keys to select the option CTC 1132 868AM 15 When Final Door Arming is programmed the Control Panel will arm after the entry door is closed For more description of this feature please refer to Sec Il Away Alarm On Mode of Operation 2011 04 27 9 Interference Turn on and off the detection feature of interference Delt eicit i oin Off If Die t je c t ji jojn On O Press A 8 W keys to select the option O Press OK to confirm O Detection Off is set as factory default lt NOTE gt Se 10 Re En When t
45. g numeric keys to the desired alphabets symbols and press repeatedly until the wanted alphabets symbols appear 2011 04 27 Release the key and the flashing cursor automatically jumps to the next position for you to continue with the next letter by the same method e The keys have the following functions y Delete character and backspace 8TUVtuv 9WXYZwxyz Ea O lt space gt 8 6 8 2 lt NOTE gt The name can be erased or clearing the display by entering backward spaces G and pressing OK e To Delete User PIN code Except User 1 which is activated by factory default and can t be deleted in any way User 2 3 and 4 PIN code can be deleted by following the steps below Step 1 Move the cursor to the item Pin Code then press OK the following screen will show the status of each User PIN code S l Mil TH x0 lt MIR MR kk ur uo uo S kk Je les l lis a Step 2 Move the cursor to the desired 2 4 of programmed user PIN code to be deleted then press OK the following screen is displayed AJOIN Dell e t le Pi in Cjo dje Ojk Step 3 Press OK and the screen returns to previous one with the deleted User PIN code marked with ee ee CTC 1132 868AM e To Edit User PIN code
46. gered eg Door is open arming is also prohibited To arm the system please see the section Forced Arming below Ill Forced Arming O While you try to arm the system by entering the PIN Code if there is any fault situation has occurred before the display will show Fjajull jt Awa y Dis p Alr jm If you move the cursor to Away Arm position and then press OK the Control Panel will sound a ding done warning sound to indicate arming is prohibited and the message Fault DSP is displayed in the middle of the top display row and alternates at 2 second intervals with individual fault events lt NOTE gt n the same situation if you arm the system by pressing the Arm button on the Remote Controller the Control Panel will response in the manner as described above and the arming is also prohibited O You will need to press G to return back to Alarm Off Screen 2011 04 27 O At this moment you can first rectify all of the problems and then clear the Fault display Please see section XI In a Fault Situation and then afterwards you can arm the system However if you want to put the system into Arm mode with the fault situation persisting it is still possible by following the steps below to execute Forced Arming Step 1 Enter your PIN Code and press OK a prompt message will be displayed
47. he Detection On is selected whenever the signal jamming period lasted longer than 30 seconds this fault event will be logged and displayed on the LCD to warn the user When the Dectection Off is selected CTC 1132 will not check interference status mote Controller Entry able Turn on and off the Remote Controller disarm function RC Ent E Off RC Ent El Oin O Press A 8 Y keys to select the option O Press OK to confirm O Remote Controller Entry Enable off is set as factory default lt NOTE gt Se Se When the Remote Controller Entry Enable is set to Off it will not be possible to disarm the Control Panel when the system is fully armed unless an entry point device is activated first This feature is used to ensure that the system cannot be disarmed with a stolen Remote Control without unlocking a door first When the Remote Controller Entry Enable is set to On the Remote Controller can Arm and Disarm the Control Panel as normal without activating an entry point first CTC 1132 868AM 11 Mobility This is to disable or enable the Mobility Timer with selected countdown period Options available are Disable 4 hours 8 hours and 12 hours If the Mobility Timer is enabled it will count down the pre programmed time length When the timer times out without being reset a report
48. her devices or Press G to return to Add Delete Device menu 2011 04 27 4 Program Siren If an outdoor Bell Box Indoor Bell Box or Universal Receiver etc is to be included in the system it should be programmed first by the Control Panel so that the Control Panel can communicate with these auxiliary devices To program these auxiliary devices select Program Siren in the Device menu Liejajr in Sii r len Siren Tjalmp Oln Siren Tja mip Of Ciolnf ji rim On Cljoin f ji rim Of If Ent iriy Sind On Entiriy Snid Of f Rie cjeji jvieir 11 Rie cleji vier 2 Learn Siren Step 1 Step 2 Step 3 Step 4 Step 5 lt NOTE gt Se If there is any detector or Remote Controller has been added already Put all the desired Auxiliary devices into learn mode Refer to their individual Operational Manual Move the cursor to Learn Siren Press OK The Control Panel will then sound a long beep and transmit Learning code to all devices simultaneously The Out Door Bell Box BX 8 should respond by activating its siren amp strobe light momentarily while the UR 7 status LED lights up for 3 seconds the position Place these auxiliary devices out of Learn mode Adding them into the system is completed If any of these devices does not respond make sure
49. ihhjainigje Kie ly Pili in cioldje 1 Keyword Editor Step 1 Press OK to confirm Step 2 The next display will prompt you to enter your preferred keyword from minimum of 1 character to a maximum of 10 character and press OK when done Kle ly wio r jd jejdii t jojr E a he OK Step 3 The system returns to Main Programing Menu automatically lt NOTE gt lf there is no character entered there is no Keyword set up in the system Without Keyword programmed in the system Remote Commanding of CTC 1132 s Receivers and Outputs via SMS will also be disabled IX Country Code When you get the SIM card please set the card in cellphone and send a SMS message to another handy for checking the number format of your SIM card Usually there are two different number format 1 With Country Code such as 46 123456 2 Without Country Code 0912345678 such as 2011 04 27 e lf your SIM card format is with Country Code like 46 123456 Step 1 Select the Country Code option and press OK The display will then show Cc Cc olujnjt ir ly o dje Step 2 You can now edit your Country Code For example Taiwan s country code is 886 Type 886 under the country code It becomes as the following
50. ill show what messages are lt S v being played The word prompt will shows the following Now Playing Address Msg Emergen Msg PA Msg Fire Msg Burglar Msg When the last message is played to the recipient and the recipient can confirm their reception amp open the listen in by pressing DTMF 1 or end the call by pressing DTMF 9 or 0 Acknowledging with signal 1 The recipient can press 1 to acknowledge the call and also initiate a One Way Listen In Channel for 2 minutes This channel allows the recipient to listen in to what is happening to the other side of the line During the Listen in period the CTC 1132 will sound one audible beep via the telephone handset signaling 20 secs time remaining alerts to the call Recipient Press DTMF 1 can extend another 2 mins If the Listen in period expires without DTMF command press the call will automatically hang up Acknowledging with signal 0 If the recipient presses 0 on his phone set as the acknowledging signal The Control Panel will then take the following actions The Control Panel will go back on hook The Control Panel will continue Alarming The Control Panel will try to dial the phone numbers of the next priorities until two recipients have acknowledged the call Acknowledging with signal 9 If the recipient presses 9 on his phone set as the acknowledging signal the following will happen The Control Panel will go back on ho
51. ion indicates the current setting CTC 1132 868AM 14 In Spc Settings if no key is pressed within 10 minutes the Control Panel will automatically exit this menu and return to Alarm Off display 1 Alarm length This is for you to select the period of time that the built in siren will sound when an alarm is activated You can choose from 1 min to 15 min in 1 min increments Al jalir im IL 3 mi in gt jh A V O n K Use A amp W keys to switch between options Press OK to confirm O 3 minutes is set as factory default 2 A Exit Sound This is for you to decide whether the Control Panel will sound short beeps during the Exit Delay period when in Away Arming Exjit Sinid On E x i t Sinid jOff f O Press A amp W keys to select the option Options available are On for Exit Sound and Off for no entry sound O Press OK to confirm eo Exit Snd On Exit sound On is set as factory default 3 A Entry Sound This is for you to decide whether the Control Panel will sound short beeps during the Entry Delay Period when Away Arming Elnt ir Elnt ir Sin Sin d d Ojn Of If y y O Press A amp W keys to select the option
52. layed Interference Interference AC Power Fail AC failure Control Panel low Panel L B battery Control Panel sabotaged Panel Tamper Sensor w Zone Sensor Low Battery Name L B Sensor w Zone Sensor Sabotaged Name Tamper Sensor w Zone Sensor out of order di Name out GSM out of Signal GSM Signal CTC 1132 868AM 38 GSM module missing GSM Missed can Pin Code GSM Pin Code Incorrect missing GSM locked by PUK GSM PUK SIM Card missing GSM isn t Ready lt EXAMPLE gt lf DC Z 01 L B is displayed it means Zone 1 Door Contact is low battery lt NOTE gt While you arm the system if any of Door Contact or PIR is triggered arming is also prohibited and the sensor triggered will be displayed as fault message Sensor triggered Message displayed DC w Zone Name open Door Contact triggered IR w Zone Name PIR triggered Active 6 Remote Control Command The Unit can be controlled by Remote Control Commands sent via SMS messages A From Regular Phone Lines Step 1 Dial the GSM phone number of your Control Panel and hang up on the first ring Step 2 Dial the Control Panel again after 8 20seconds Step 3 You will hear 2 beeps from the Control Panel via phone set Step 4 Enter the
53. lr nie lw No Olk Press G to abort and the screen returns to Tel Number screen Step 4 Key in the new number and choose a preferred reporting method Step 5 Press OK The new number will then override the previous one The screen returns to Tel Number screen O Delete Tel Numbers To delete a telephone number follow the Step 1 to Step 3 of Changing Tel Number described above and when Enter new No prompt screen is displayed Elnit le lr nie lw No Olk Step 4 Press OK then the previous stored number will be deleted 2 Message Menu e This menu is for you to record and play the emergency messages Rie c jor d Mis g Telsit r je pjo e e With a total capacity of 20 sec you are allowed to record the emergency messages in 5 parts Address message 8 sec Burglar message 3 sec Fire message 3 sec Panic message 3 sec Emergency message 3 sec 2011 04 27 The Address message must be recorded or the Panel will not dial out at the Alarm situation e In an emergency the Control Panel will dial the emergency phone numbers according to the priority order then first play the Address message and then play the specific part message Burglar Fire Panic
54. med mode Alarm off entering a valid user code can access the user menu the system can then be Away armed or Bypass armed via this menu When the first numberic key is pressed the display will show Enit je ir Clold le when the complete PIN code is keyed in followed by OK within 10 sec the first two lines of the user menu is shown Awaly Ajr m Home Ar m A flashing dot will appear next to Away Arm the complete menu list consists of WwW y Alr m e Alr m a s s vru ID ojojo Se fo 5 2 e ir js wi t jcjh These items can be scrolled through by using the V A keys CTC 1132 868AM lt NOTE gt If there is any fault event occurred no matter if the fault condition has been rectified or not when you enter the PIN Code followed by OK the following screen will be displayed Fia jujl jt Disip Awjiay Ajr im Hiome Ar im Bly p ja s is Lolg Cjoinit roll PISIS And the cursor stays at Fault Dsp position To arm the system please see the section Forced Arming below f there is any SMS message saved the screen will display SMS for SMS message reading f you press G
55. move the battery Step 2 Apply power while holding down the A key Step 3 Release the A key when a tone is heard Enter Code will be displayed Step 4 Enter the following keys sequence AVAVAVAV OK Step 5 The display will show Rie sje t Eelp ir om Y N Step 6 Press OK Step 7 All programmed parameters are reset to factory default setting lt NOTE gt Once the System Reset is executed all the programmed data are returned to its default value and all the devices having been learnt in are removed You have to do the programming and learn in the device one by one again 2011 04 27
56. n User PIN Code 1 1234 has to be keyed in every time Entering Code is required O User PIN code 2 4 are deactivated by factory default All 4 User Pin Codes are used to regularly arm disarm the system and are allowed to access the Programming mode accompanied with the Master Code To set your own PIN code Step 1 Move the cursor to the item Pin Code then press OK the following screen is displayed kkk ll Peek da ek Step 2 Move the cursor to the desired of User Pin Code then press OK the following screen is displayed N a AO Eint le lr Nie w Cjojdje Step 3 You can key in your preferred 4 digit number then press OK Step 4 The following screen will be displayed Rie pieja t Nje w Clo dje You are requested to enter the same code again as the one entered in Step 3 Step 5 Key in the same code again then press OK If the code is correct the following screen will ask you to enter the user s name for reference Elnit elr Nle w Nla mie Ok Step 6 You are now invited to give a name for CTC 1132 868AM this User who will be using this newly programmed code to help better understand sy
57. ne edit your SMS message by selecting SMS Editor in Programming Main menu 1 Editing SMS message Step 1 During this display compose your own SMS message of up to 14x4 56 characters maximum Press OK to confirm The keypad can be used to enter text similar to the testing method being utilized for the mobile phones The keys have the following functions A Backward space LY Forward space e omNo mao and backspace e etuv o owxvzwyz Lo o lt spaces 80 7 When the message is completed press OK to see the next display Slalve Quii It Press Save to save the newly edited SMS or exit this section back to Programming Menu by press Quit Step 2 Press OK when the cursor is moved to the choice of your decision When Save is chosen the saved SMS message will be sent when any alarm is triggered and displayed again on the LCD when the SMS Editor is selected again CTC 1132 868AM 25 VII SMS Keyword For sending remote commands to control the operation of the Receiver 1 amp 2 and Outputs using SMS message a personalized password is required for CTC 1132 to recognize your authority To set a personalized keyword different from Pin Code factory default select SMS Keyword in Programming Main menu C
58. ng For an alarm event the reporting is done via sending pre edited SMS messages to the mobile phone numbers programmed at this step Step 5 Select a preferred reporting style and press OK The screen will return to the Tel Number screen to show you the stored phone number with a letter V indicting its a Voice report style and a letter S for SMS report style A 2 21805 51 V B 2 6 9 4 0 6 3 3 S The maximum length of a number is 20 digits including amp FP If this length is reached the Control Panel will sound 5 beeps and no key can be keyed in except G key and OK key During entering the number the G key is used as backspace However if the number field is empty pressing the G key the screen will return to Tel Numbers screen During entering the number when the 15th position is reached non fitting numbers will scroll sideward to the left O Change Tel Numbers Step 1 On the Tel Number screen Press OK Step 2 The following screen will be displayed for you to confirm if you really want to change CTC 1132 868AM Chlalnmge Nju mb fe jr 2 2 1118 0 5 5511 Olk Step 3 Press OK to confirm The following screen will be displayed for you to enter the new number Elnit le
59. nit to turn off the Power switch 2 and send a confirmation SMS back J JO E 112314415 2 1 0 1 to your mobile phone The format is The programmed User PIN Power Time SMS keyword Code switch Number J O JE 1 23144 5 2 0 0 0 The User Power Confirmed programmed PIN switch e de SMS keyword Code Number XIII Dialing amp Call OTE Acknowledgment 5 A confirmation SMS message will read 1 Auto Dialing on your mobile phone as O lf the system is in Arm mode when an Confirmed Joe 1234 520 00 alarm occurs the Control Panel will immediately dial the phone numbers you preset and play the recorded messages CTC 1132 868AM 40 2011 04 27 2 If the system is in Home mode or Disarmed mode when an audible alarm is initiated the Control Panel will wait 15 seconds and then dial the phone numbers After dialing the Control Panel will delay 5 seconds then starts to play the message It firstly played the general part of the recorded message address then plays the specific alarm message Burglar Fire Medical or Panic depending on the nature of the alarm To ensure the call is successfully received by the recipient the recipient should acknowledge the message by pressing the appropriate button on his telephone set The Control Panel while playing the message will check if there is any acknowledgement signal being received If the recipient does not acknowledge the call the message will be repeated for a period of
60. nnnnnnanrnnenannnnanninennininnss 29 VoHomesArmi Mode trette n opaan ed aaahe eau tl Snubs eet edniy roliad 29 Mi Partial By pass Arm Mode iis iii abet cess eaten aie eee ei tide i ee ee 30 VIL Alarm Activation a e r Site heehee seed a 32 VIII Stop the Alarm and Alarm Display ccccceeeeeee eee eeeee a eats eee ee eae eeeeee eee ese ea eeeeeeeeeaeeaeeeeeeas 33 Xs Event LOG caera hae ee ea Ee ee ee ae 34 Xs POWET SWT MS a a a a lesen XI False Alarm Management 0ccccceeeee eee cette eee e eee trst trutt ttnt eee ttur tru anes ea uan tn ea eseeaeeeeas 35 Xi Faulty Situanons a dt ea teeta Pare tee I sede E A pearance 35 XIII Dialling amp Call Acknowledgment cccceceeeeeeeee eee e eee sent eens tenes eee eeaaeee ea eeeeaeaeeeeaeaeegs 40 o A nls Soe oe eee ee Reset ed 0001510 0 nn nana nana 42 Application Overview Identifying the parts 16 a E 0 E o o BHO E Eb G Gu Gm w o Bm G OH E 0 20 w 8 7 6 5 Backlit LCD Display Green Power LED ON AC Power is On OFF AC Power failure Yellow Fault LED On when any fault situation Fault is detected E Off when all fault conditions are restored The Unit is in Normal Al Mode Numeric Keys 5 A Key Programming mode press this key to move the cursor and scroll the display upwards 6 Y Key
61. nt can be logged be cleared manually reported and displayed on the LCD if O i Fault Display submenu is chosen On the contrary the fault message display retains even if the faulty conditions have GSM isn t ready been restored If the SIM card is found missing a e The fault message can only be cleared warning message will be generated manually after the fault condition has been rectified CTC 1132 868AM 36 2011 04 27 3 Viewing Clearing the Fault Message 4 Fault Event Response O When a fault condition is detected in addition to the fault display the Control Panel will also respond separately according to the nature of the fault event To check what the fault condition is Step 1 When the system is in Disarmed mode Enter your PIN Code followed by OK Step 2 The screen will display F jajujl jt Dsip Arm and the cursor stays at Fault Dsp Step 3 Press OK to select Fault Dsp Step 4 All the fault events are listed Use A W key to move the cursor downwards or upwards The screen is also scrolled down or up respectively Step 5 After viewing all the fault events press G gt key a prompt message is displayed Cl ejair Fialull jt Dis p OK Step 6 After the fault condition has been rectified press OK and th
62. o dial the phone numbers of the next priorities until two recipients have acknowledged the call Acknowledging with signal_9 If the recipient presses 9 on the phone set as the acknowledging signal the following will happen Y The Control Panel will go back on hook The Control Panel alarming and stop dialing Y will stop 3 Auto Redial When only one Emergency phone number is stored and that number is engaged the Control Panel will automatically redial that number up to maximum of 5 times with an interval of 62 sec between dialing attempts When more than one telephone numbers 2011 04 27 are stored the Control Panel will dial in accordance to the set priority order If the number being dialed is engaged it will try the next number Each number will be tried a maximum of 5 times and the redial interval between each number is 5 sec e The maximum number of times the Control Panel will retry is 15 times f no phone Number is programmed the Control Panel will not dial When dialing a pager number the Control Panel will only send the identity code it will not play the message and the call is not considered to be successful The same pager number will be dialed only once CTC 1132 868AM Appendix l Reset Procedure 4 Reset to Factory Default Setting The Control Panel can clear all programmed parameters by the following sequence Step 1 Power down Control Panel and re
63. ok CTC 1132 868AM Y The Control Panel will stop alarming and stop dialing lt NOTE gt Messages will be played in the following order Address Emergency Panic Fire amp Burglar message Until the recipient acknowledges and confirms acknowledgement on his or her phone the control unit will play the message for 85 sec before returning to selection menu Pressing G will return you to the menu with the list of numbers If the Burglar message Emergency Message Panic message or Fire message has not been recorded when you do the Test Report it will be ignored O Changing a message If for any reason you want to change any part of the recorded message just follow the same procedure to record a new message for that part The new message will override the previous one Ill General Settings In General Settings menu the following parameters can be programmed at your discretion PPliin Clold e Tle mp Cjo d e Dulrelss Clio dle Mla is t eir Clio ldle A Ent r ly T i me A Elx i It Tli me H En t ry T i me H Exit Tli me Diolor Cihli me Tli mie Dia it je Panel Sli rien Llanguja g je 2011 04 27 1 Pin Code O There are 4 User Pin Code in total and each consists of 4 digits User PIN code 1 is activated with 1234 as factory default Before you set your ow
64. oller will have to be silenced at the Control Panel only See section Stop the Alarm 2011 04 27 Press G all the learning setting processes having done will be ignored the screen returns to Device menu Other Devices For Smoke Detector Remote Keypad Water Sensor and Night Switch no further option needs to be specified hence after it is detected a zone is assigned and the zone name entered the following screen is displayed l jnjs it jajil leld OIK S D Lji v ji n g r o o m Press OK to confirm adding a smoke detector or a Remote Keypad or a Water Sensor or a Night Switch is now completed Detectors can be given names and location descriptions to help understand system events The devices can be named when first installing them or by editing them afterwards the procedure is similar for both situations e When the Enter zone Name screen is displayed the keypad can be used to enter text Simply locate the corresponding numeric keys to the desired alphabets symbols and press repeatedly until the wanted alphabets symbols appear Release the key and the flashing cursor automatically jumps to the next position for you to continue with the next letter by the same method e The keys have the following functions EJE 2ABCabo Delete character and backspace e eunomno 0 a eruvw e awx
65. or Home Omit PIR Detector 5 A for Home Access PIR Detector D for Delay PIR Detector E for Entry PIR Detector StepB8 Use the W A to make your selection and confirm by pressing OK You are now invited to give a name or location description to the device to help understand system events You can enter up to 10 letters as you please for the name followed by OK or just press OK for no name Please see section Device Naming for details O StepB9 Press OK when finished and the display will show The display will show the newl zone name and the attribute next to the device l jnjs t jaji l jejd OK LIR Hall waly E StepB10 Press OK adding a PIR is now completed screen returns to the Device menu lt NOTE gt Press G all the learning setting processes having done will be ignored the screen returns to Device menu Remote Controller StepC7 After a zone number for the RC is assigned the following choice screen is displayed Pelrisjonjall Ajt it Mie dji jc ja l Elmg lt NOTE gt For a Remote Controller you may choose between Personal Attack and Medical Emergency device mode CTC 1132 868AM 20 p
66. r is turning the power switch modules ON OFF from CTC 1132 panel they should wait for at least 4 seconds between each operation XI False Alarm Management CTC 1132 has a regulatory management facility built in false alarm v Dual Ply Entry Wanring Y Sequential Verification Alarm Reporting Dual Ply Entry Warning This is to warn the user that an alarm report to the Emergency Phone Numbers is about to be made When a zone that is not programmed for delay is violated during the Entry Delay or the correct PIN code was not entered within the programmed Delay period a 30 sec internal alarm is given before an alarm report is made lf a valid user PIN code is entered within the 30 seconds the alarm will be aborted and the system returns to normal status If no valid user PIN code is entered a burglar alarm will be sent CTC 1132 868AM 35 2 Sequential Verification Reporting e A sequential verification alarm report is generated when a second alarm from a different Burglar Door Contact or Burglar PIR is registered within a 30 min period e This Sequential Verification Report will be sent in addition to the alarm report Alarms cannot be verified after the Entry Delay has been initiated XII Faulty Situations O The Control Panel is capable of detecting following fault events Y Control Panel Low Battery AC Power Fail Sensor Out of order Sensor Low Battery x Sy SN Device and Control
67. r keys until all the alarm events are displayed thoroughly then the display will show S N s t eim rrelalc hlte d nie ox Step 7B Press OK the display returns to Alarm off If the alarm is stopped after reporting has been finished Step 3C The device that triggered the alarm with its zone number is displayed All ja r m St jar tleld by 011 R Hjaj wja y e Proceed to display the alarms and clear the alarm displays as specified in Step 4A Step 6A in previous section 2011 04 27 Step 4C After all the alarm events are cleared then the display will show S y stlelm rielacihield 2 6 9 4 0 6 6 7 Step 5C Press OK the display returns to Alarm off When an alarm other than Panic Alarm is raised press the Disarm button on the Remote Controller will also stop the alarm Optional Panic Alarm must be silenced at the Control Panel This is to prevent the Remote Controller from being snatched from the user and silence the alarm using the Disarm button 2 Alarm memory If an alarm was raised without being silenced during your absence and the alarm reporting has been carried out the screen will stay on the Alarm warning display AJLA RIMI AL ARM AL ARM
68. repeat it for double confirmation Ok Step 2 Step 3 Press OK and editing the Duress code is completed 2011 04 27 4 Master Code O Master Code is used for accessing the Programming mode and it is set to 1111 as factory default Before you set your own Master PIN code 1111 has to be keyed in every time it is required To set your Master Code follow the same steps as in setting the Duress Code described above e To Edit Master Code After the Master Code is programmed it can be edited by following the same steps as in editing the Duress Code described above lt NOTE gt The Master code can not be deactivated same as the User 1 PIN Code The Master Code is used only when you enter the Programming mode In other cases only PIN Code should be entered lt IMPORTANT NOTE gt When entering the following individual setting screens the value displayed on the screen is the current setting of each item If it is not necessary to change the current setting just press to escape 5 A Entry Time This is for you to select the Entry Delay time when Away Arming Options available are 0 sec 10 sec 20 sec up to 70 sec in 10 sec increments A 2 Tli me AVIO Ejnit rly 0 sjejc K Use A ww between options
69. ress Situation in Progress CTC 1132 868AM 11 e The Duress Code consists of 4 digits and is not activated as default by the factory e To Set Duress Code Step 1 Use the arrow keys to select Duress Code and press OK Elnit je lr Nie w Clio d e Step 2 You can key in your preferred 4 digit number and then press OK Rie pjeja t Ne w Clio de Step 3 You are prompted to re enter the same code again and press OK If the code is correct the screen returns to General Setting menu setting the Duress code is completed e To Delete Duress Code After the DuressCode is programmed it can be deactivated deleted by following the steps below Step 1 To delete programmed Duress code select the Duress Code from the Gen Setting Menu then the screen will show Dell le lt je Pli inl Cjo jd je Step 2 Press OK to confirm e To Edit Duress Code After the DuressCode is programmed it can be edited by following the steps below Step 1 To edit programmed Duress code select the Duress Code from the Gen Setting Menu then the screen will show Die l le t je Pli inl Cjo d je Press G key the next screen will ask you to enter your new Duress code and
70. rted lll The Power Supply An AC power adapter is required to connect to a wall outlet Be sure only to use an adapter with the appropriate AC voltage rating to prevent component damage A DC 9V output and 500mA adapter is generally used to power the Control Panel CTC 1132 868AM O Rechargeable Battery O In addition to the adapter there is a rechargeable battery inside the Control Panel which serves as a back up in case of a power failure O The battery used is a Ni MH 600mAH 7 2V rechargeable battery O During normal operation the AC power adapter is used to supply power to the Control Panel and at the same time recharge the battery When the battery is fully charged it can provide back up power for a period of about 8 hours It takes approximately 48 hours to fully charge the battery lt NOTE gt f the AC power is missing and the battery is near exhaustion a low battery message will be displayed and the internal siren and Backlit feature will be disabled to conserve power IV How to install the Control Panel 1 Locating a suitable position for the Control Panel The Control Panel requires mains power and a constant telephone connection e The Control accessible Panel should be easily e The Control Panel should not be placed in a damp place such as a bathroom e The Control Panel should not be placed close to any heat source such as microwave ovens which can reduce signal srength
71. set as factory default 13 Latch Option You are requested to choose to have all arm disarm actions of the user temporary user to be reported via SMS Latich iRpit Of f Llaltich Ripit Oln Use W amp A keys to select the options Press OK to confirm 14 Supervision This extra option is used to enable system supervision function When this option is chosen ON CTC 1132 will be able to receive the check in signals from its system devices to indicate their proper functioning b TITV TI OJO O W ofcjci c 00AaU l r r r u I10N1N 1H O 2 s Oo Use W amp A keys to select the options O Press OK to confirm e Disable is set as factory default 15 Stop Press OK to return to the previous menu V Add Delete Device If Devices is selected in Programming Main menu the Device menu is displayed From here you can edit all the devices CTC 1132 868AM previously learnt in add or delete devices including the external sirens Aldjd Die v ji c e Edi t Dielvii cies Rie mo v je Die lv i c le Pir jojg r lajm Si r jejn Pir jo g r ja m PISIS 1 Adding Devices Step 1 To learn in a sensor move the cursor to the posi
72. splayed All jar im St jajr t jejd By 0 1 1 R Hja l jl jwialy Step 4A Press OK Step 5A If there are more than one alarm events have been raised the Control Panel continues displaying the 2nd alarm event with 02 Stating at the beginning of the 2nd line Step 6A Repeat pressing further keys until all the alarm events are displayed thoroughly then the display will show Sly s t je jm _ r je ja jc jhje d Nilo nie Step 7A Press OK the display returns to Alarm off CTC 1132 868AM lt NOTE gt Press G or no key is pressed within 5 sec the screen returns to 1 device display You can repeat from the beginning to view the alarm event one more time No alarm reporting will be made However one OPEN report by the user will be reported If the alarm is stopped before reporting is finished Step 3B The screen will show you which device triggered the alarm with its zone number displayed All jajr m Sjt jajr tjed Bly 0 1 R Hjaj jl wa y Step 4B Press OK Step 5B If there are more than one alarm events have been raised the Control Panel continues displaying the 2nd alarm event with 02 Starting at the beginning of the 2nd line Step 6B Repeat pressing furthe
73. stem events You can enter up to 10 letters as you want for the name followed by OK or just press OK for no name Please see section Device Naming for details Einit eir Olk StepA9 Press OK when zone name entering is completed The display will show the new zone name with the attribute next to the device and prompt you to confirm your programming l jnjs jt jaj jl je d OK DIC Blalc k d o o r O B StepA10 Press OK adding a Door Contact is now completed screen returns to the Device menu lt NOTE gt Press G all the learning setting processes having done will be ignored the screen returns to Device menu PIR Detector StepB7 After a zone number for the PIR is assigned the following choice screen is displayed Blulr gll ja jr Hijo mie Ojmii t Ho me Alc c eis s Del la y Ejnit r ly lt NOTE gt For a PIR Detector you may choose between Burglar Home Omit Home Access Delay and Entry For detailed functional description of PIR Detector in these 4 different device modes please refer to the Note section following Step A7 for adding Door Contact 2011 04 27 B for Burglar PIR Detector O f
74. stem events You can enter up to 10 letters as you want for the name followed by press OK or just press OK for no name Please see section User Naming for details Then the screen returns to the PIN Code menu showing post programmed status of each User PIN code 11 MR S MII ITH 2 MRS SIMII TH 3 kk gt k gt k gt k 4 lt NOTE gt 2 MRS SMITH representing the User 2 PIN code is set up and user name specified 3 Xakokok representing this User 3 code is programmed without user name specified 4 eeee representing the User 4 code is not yet set up for activation Step 8 Proceed to set additional User PIN Codes as instructed from Step 2 Step 7 When done press G and the screen returns to General settings menu setting the PIN code is completed lt NOTE gt 5 In Step 5 if the code is not correct a Code is not correct prompt message will be displayed 2 sec and you are requested to repeat Step 3 to enter again User Naming Each individual User can be given a name for easy recogniztion when understanding system events User Names can be named in the first time setting or by resetting The procedure is similar for both situations e When the Enter New Name screen is displayed the keypad can be used to enter text Simply locate the correspondin
75. tion Add Device then press OK a prompting message is displayed x IPiuisih Blut t jojn Oln Die vii lcle tjo Ald id Step 2 Press the test button on the sensor or any button on the Remote Controller Step 3 If a signal is detected the screen will show you the type of the device on the second line Die lt e lc Olk Diolor Clon it ja jc lt o a lt NOTE gt The categories of devices are listed as followings Y Door Contact DC v Panic Button PB v PIR Sensor IR Y Remote Controller RC Y Remote Keypad KP Y Smoke Detector SD v Water Sensor WS v Outdoor Siren BX v Universal Receiver UR Y Wireless Siren SR Step 4 Press OK to confirm the device type A prompting message will be displayed for 2 sec to prompt you to select the zone number for the device Siell je lc it Die v ii c e e Zio n le 2011 04 27 Step 5 Then all the available unused zones zones which have no device added in out of a total 20 zones will be displayed on the screen Zioinje 0 1 Zioinje 10 2 Zio nie 013 Zioinje 1 9 Zioinje 210 S TOP Step 6 Use A 8 W ke
76. to Step 3A Step2A Use A W keys to scroll the display and choose the desired device attribute by pressing OK The screen will show Z D Oik E o ne C Tiy ple Bia c k d jojo r Step3A Press OK to confirm The next screen will ask if you want to change the name Pir jogir ja Bia jc ik jd jo m Nia ojr Press G if re naming is not required to exit to the previous device list or press OK if you wish to edit the zone name Nia Step4A Elnit elr Olk Step5A Edit the zone name and press OK when completed to return to the previous device list Step6A Proceed to edit other devices or Press G to return to Add Delete Device menu To Edit Other Devices SD KP WS NS Step1B Use A W keys to scroll the display and choose the desired device for editing When selected by pressing OK the first screen will ask if you want to change the zone name To confirm press OK or press Q to exit m O r Prioigirja Bia c k d jo Step2B Press OK if you wish to edit the zone name CTC 1132 868AM 22 Oik or
77. vzmya Lo d lt spaces a e When the name is complete press OK CTC 1132 868AM to confirm and return to the previous or main menu lt NOTE gt The name can be erased or clearing the display by entering backward spaces and pressing OK Device Display Nomenclature The devices are displayed throughout the menus and especially where there are zone lists The meanings of the display components are shown in an example below Zone number Device type Zone attribute PIR Zone 03 B The PIR detector is in zone 03 programmed for burglar mode 2 Edit Devices To edit all the devices that have already been installed choose Edit Devices in the Device menu all the devices being included in the system will be displayed You may Press G to exit DC Blac kid jo lo r LIR Hall w a ly RIC MR SIMII TH SiD Ki t c hjejn S t oip Step1A Use A W keys to scroll the display and choose the desired device for editing For DC IR and RC when selected by pressing OK the first screen will ask if you want to change the device attribute 2011 04 27 Buligillar Hio mie Omi It Hoj me JAjc cle js s Ent ir ly 24 Hjojuir Fii r je Meldi cial E mig Wa It je r If no changes is wished here press G to skip
78. will be made to the Programmed phone numbers s H H o AO o lolo T 2 s Oo Use VW amp A keys to select the options O Press OK to confirm e Disable is set as factory default lt NOTE gt ail When the Mobility is set with a specified timer the Control Panel will report to the Programmed phone numbers when the timer runs out unless one of the following actions occurred in advance to reset the timer In Home mode whenever any Home Omit DC IR is triggered or whenever any of the keys of the Control Panel is pressed In Disarm mode whenever any of the DC or IR except 24 Hr Fire Medical Emergency and Water is triggered or whenever any of the keys of the Control Panel is pressed en When the system is set to Away Arm the timer automatically stops When the system enters Home Arm or Disarm mode the timer automatically starts again 16 2011 04 27 12 Tamper Alarm This extra option is to choose for Tamper Alarm of unauthorized sabotage to the devices only when the system is Away Armed in addition to the normal operational directive of Tamper Alarm Awjaly Ar m Onl ly No r m a I V Use W amp A keys to select the options O Press OK to confirm O Away Arm Only is
79. you want to put the system into Arm mode with the opened door it is still possible by following the Steps described above to execute Forced Arming IV Disarm Alarm off mode Disarming the system To disarm the system If the system is in either the Away Arm mode or Home Arm mode Alarm ON enter your pin Code and press OK If the PIN code is correct the Control Panel will sound 2 short beeps and return to Disarmed mode The screen will show Al Jajr 0 6 14 m 3 Off 0 lt NOTE gt When the system is Home Armed pressing the DISARM button on the Remote Controller will disarm the system When the system is Away Armed pressing the DISARM button on the Remote Controller can disarm the sytem when either an Entry device has been triggered or when the Remote Controller Entry Enable has been set to ON V Home Arm Mode The Home mode allows the home to be Armed so that no one can get inside without first Disarming the system yet the person already inside the house can move freely without self triggering the alarm lt NOTE gt You can enter the HOME mode only when the system is in DISARMED mode 2011 04 27 1 Entering Home Mode Step 1 When the system is in Disarmed mode key in your Pin Code then press OK Step 2 Press W to move the cursor down to select Home Arm
80. ys to move the cursor to the desired zone number then press OK lt NOTE gt When a sensor is added to the system for the second time without removing first An error message will be displayed All r je jajdly Elx i s t i in sly s t je m The message will be displayed for 2 sec then the screen return to Step 1 screen to wait for the signal from another device Pressing G key will abort the procedure and will not learn in the device Depending the type of the device different screens will then be displayed accordingly for further configuration purpose Door Contact StepA7 After a zone number for the Door Contact is assigned you can futher specify how it will work in different modes You are requested to make a selection among Burglar Home Omit Home Access Delay Entry Away Only 24 Hour Fire Medical Emg and Water device Bulrigillar Home Olmi It Hiomie Acc leisis CTC 1132 868AM 18 oxx o o rT o voi A3 o gszmnmo lt NOTE gt B for Burglar Door Contact O When the system is in Arm mode if a Burglar Door Contact is triggered a Burglar Alarm will be activated immediately and

Home Prosafe 1132 GSM

Contents

Download Pdf Manuals

Related Search

Related Contents