GSM Alarm Kit User Manual Ver 1.20 Date Issued
Contents
1. The user cell phone number is 13570810254 and has been assigned as a SMS Alert number the simcard number in the panel is 13512345678 Problem 1 Alarm but the user hasn t received the SMS Alert Solution Please plus the country code while you setup the 13570810254 as SMS Alert number means setup 008613570810254 to instead of the 13570810254 Problem 2 The user number can receive the SMS Alert message from alarm panel but the alarm panel can not receive the commands from the user number Solution Please add country code to the simcard number in the alarm panel Means send sms commands to 008613512345678 to instead of 13512345678 Solution 3 When you use cell phone dial another one what number it will be displayed then you can set the displayed number as dial numbers when you use cell phone send SMS to another cell phone what number it will be displayed then you can set the displayed number as SMS Alert number just use the 00 to replace the y If Switch off the siren then all alarm raised will not drive the siren if switch on the siren then when the system alarm will drive the siren for 1 minute except the SOS help caused Default is Switch on If setup the Report Time Gap the system will periodically send GSM Alarm System in good working condition to the first SMS Alert number This is very useful for long time use the system Default is 0 Means will not report the system condition If enable the p2. on the remote control or press Disarm button on the Keyboard then input the password the Control Unit disarms immediately The i ICON will be off Under this status any sensor triggered the control unit will not alarm Except the sensor type is the 24 Hour Zones or Watchdog zone or SOS zone Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 Press the button fF on the remote control or Press the Arm button on the keyboard then select Stay the Control Unit enters Stay Partial Armed status the f ICON will be on In this status the sensors had been set as Stay Type triggered will alarm but the sensors had been set as normal Type triggered will not alarm Please see the menu of the Edit RF Zone Press Emergency button SOS l on the remote control or the control unit or Press any Emergency button The Control Unit will enter emergency alarm The siren will not sound but will alert the pre set phone number immediately 7 2 SMS Commands for Arm or Disarm or Inquiry system status or switch on off independent output relay The User can Arm Disarm Inquriysystem status Switch on or off the independent output relay by sending SMS to the Control unit The SMS Commands are below The system will carry out the commands immediately with no delay after the Control Unit receive this SMS command 7 2 1 Armed Example Return SMS Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 7 2 2 D
3. In order to power off the alarm system by intruders we equipped the power switch inside it is nearby the SIMCard socket please pay attention to it and don t tell others Page 0 of 30 Ver 1 1 File No GSM ALARM KIT 160012 of this Turn it towards inside is switch off turn it towards outside is switch on 2 We reserved the plastics of the output relay Because of some of the users needn t this function If you want to use the output relay please remove the plastics carefully Then you can see the output relay connectors inside 3 The left output relay is independent output relay the one nearby the power socket is the alarm link output relay Please pay attention to it LN O 12V LA Independent Output Relay Alanon Link Output Helay iii Interface Description Independent Output Relay Can switch on or off by SMS Commands Rated Voltage 3A 250VAC this relay is very useful to switch on light when you can not come back in the evening Then some hours Link Output Relay when the system alarm will close 4minutes Rated Voltage 3A 250VAC this relay can connect to any other lights or CCTV system as a switch Siren Socket 12VDC Output Inner is positive electrode outer is DC Input 9 12V 1000mA Inner is positive electrode outer is negative electrode negative electrode GSM Antenna Gain 2 0dB Gain 2 5dB for 3m GSM ANT 4 2 Working Principle Drawing The GSM ALARM KIT 16 works with
4. 16 can accept total 16 wireless sensors to 16 wireless zones each zone can be assigned one wireless sensor and renamed it by SMS Command And 5 remote controls 5 Zone Serial Number Default Zone Name and Zone Attributes Table Zone s Default Zone Name Default Zone Attribute N 2 3 4 E den rom Front Balcony Normal Page of A0 Ver 1 1 File No GSM ALARM KIT 60012 12 Medical Button Alarm 24 Hour zones This attribute can not be 13 Gas Leakage Alarm modified In arm or disarm or stay mode once the sensor in these zones 14 Smoke Fire Alarm triggered will alarm immediately alarm if the sensor hasn t been triggered in the preset time will alarm SOS zone The attribute can not be modified In arm or disarm or stay 16 SOS Help mode once the sensor in these zones triggered will alarm immediately But Watchdog Zone the attribute can not be modified In arm or disarm or stay mode once the sensor in this zone 15 Watchdog alarm triggered in the preset time will not not drive the siren Notice The SOS button on the Keyboard and remote control is the same attribute with the SOS zone Page of A0 Ver 1 1 File No GSM ALARM KIT 160012 6 2 2 2 Basic Setting To setup the SMS Alert Number must be cell phone numbers total 3 To setup the Auto dial telephone number total is 5 To setup the time and date information The Format is Month Date Year Pre
5. 60seconds and the link output relay will close 4 minutes 6 3 Modify the SMS Alert Content of the Zone Zone or Sensor Name The GSM ALARM KIT 16 accept SMS Command to modify the SMS Alert INumber New Zone Name the Max Character for the zone name is 32 The Zone Serial Number is 01 16 corresponding to the LCD Menu If setup successful the system will return OK to confirm the operation Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 E g Modify the first wireless zone name as Front Door Opened by Intruder You should edit a SMS Content 12344 M01 Front Door Opened by Intruder De 1234 is the password Then send it to the GSM ALARM KIT 16 Simcard Number 7 Operating Instructions Tips The user can arm disarm Stay Partial armed by Remote controls Keyboard SMS also the user can cancel the alarm by Remote Controls Keyboard SMS to Disarm it Another the user can switch on or off the independent output relay by SMS Commands 7 1 Arm or Disarm or Stay Partial Arm At House Arm and Emergency Alarm by remote controls Press the button ii on the remote control or Press Arm button on the keyboard then select Arm the Control Unit enters arm status delay time according to the setting the imi ICON will be on Under this status any sensor triggered the control unit will alarm if answered the call the siren will stop and can listen in the alarm area by phone Press the button mi
6. SMS Alert and dial to the pre set cell phone when any sensor had been triggered Equips with 16 Wireless Zones zone attribute Normal At House or Stay mode and Zone Name is editable 3 X 24 Hour zones for smoke and gas leakage sensor 1XWatchdog zone for monitoring elder or child 1XSOS zone for emergency help Supports 3 SMS Alert Numbers and 5 Calling alert numbers and 20 Alarm Records for owner review Supports Timer for automatically arm or disarm the system Supports armed delay to give enough time to you go out the home the delay time is editable by user Equips with 1 Alarm Link output relay once the system triggered the output will switch on for 4minutes Equips with 1 independent output relay it can be switch on or off by SMS Commands This is very useful for remote switch on light or off while you re in another city in the night The Keypad can use as a dialer the functions like the Cell phone The external power failure amp recovery alert function is optional Page O0 of 30 Ver 1 1 File No GSM ALARM KIT 160012 14 Supports wiretap through the internal microphone 15 Supports internal Speaker to special user for two way voice communication 16 It is Compatible with PT2262 2264 and PT2242 wireless IC 17 Standby internal rechargeable battery which can last 12 hours 18 Based on the GSM communication network and Operation Menu Display technology apply to wide range situations 6 Sett
7. new remote control to replace it 9 5 Delete all wireless sensors and remote controls Go back to the menu then select the Remove All select it then the system will alert Are You Sure Press Enter to remove all the RF Parts of the system 10 Technical specifications of Control Unit Rated Voltage 9 12VDC 1 5A Standby current 30 40mA Siren Output Voltage 12VDC Working temperature 100 0 601 Storage Temperature 20 60 Relative humidity 10 90 No condensation Work frequency 900 1800 MHz or 850 900 1800 1 900MHz Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 Communication protocol GSM PHASE 2 2 include data service Wireless sensor receiving frequency 433 92 MHz Wireless sensor permission quantity 16Pcs Remote Control permission quantity oPcs Effective distance wireless of remote control 100 m Battery Built in lithium ion battery 1000mMAh 3 7V Standby time Approx 24hours depending on the network condition Size 180mmX125mmX30mm LXWXH Net Weight 0 32Kg 11 Important information 1 Please read the User Manual carefully before you install the Control Unit and set the Control Unit 2 Do not install the system in close vicinity with objects that generate strong interference such as TV set and computer 3 Install the system in a hidden place 4 Avoid getting water into the Control Unit 5 Have a secure connection to t
8. time point to enter disarmed mode directly Enabled the Watchdog zone In the fixed time range if the sensors in the watchdog zone hasn t been triggered will alarm CN Enabled the system condition report function Will automatically send system arp l condition to the user by SMS otherwise it will not display 6 1 3 Keyboard functions The GSM ALARM KIT 16 uses the icons to mark the buttons it will be more user friendly to user Disarm Exit and Backspace button Arm Stay and Up towards button SOS Down towards button Enter button Turn Left Right button in special menu need it to choose the option 6 2 Main Menu In standby mode press the SE button you can see the Menu To check the settings and event records of the system To setup the system functions requires password the default password is 1234 6 2 1 View To check the alarm records up to 20 event records will be saved To check the Timer you have setup To check the SMS Alert Contents of the Related Zones and its attributes To check the SMS Alert Numbers To check the Auto dial telephone Numbers To check the report time To check the RF sensor wireless code 1 The RF Code Query function is for check the wireless sensor transmission You can enter this submenu then triggered the wireless sensor if in the LCD can display some codes means the wireless sensor can transmit wire
9. GSM Alarm Kit User Manual Ver 1 20 Date Issued 2010 05 14 Picture for reference only Actual accessories may differ N A mMm A YH 10 Il 712 I3 14 Table of Contents Brief introduction 2 Safety Directions 2 Standard Packing list 3 Physical Layout 3 Features 5 Settings EE 7 Operating Instructions 17 Installation 20 Add wireless Sensors 24 Technical specifications 26 Important information 27 MaintenanCce 27 Quality Warranty 28 Trouble Shooting Guide 28 160012 1 Brief introduction The GSM Alarm System GSM ALARM KIT 16 is a new security protection solution special for home house and office and other applications It based on Wireless GSM Communication network integrated Lcd Menu display and Computer technology When any sensor activated it will Call amp Send SMS to owner s telephone immediately The GSM Alarm System GSM ALARM KIT 16 with user friendly design idea all operations and settings are visual and intuitivel What you need is a SIMCard whic
10. Voltage Indicator Work Indicator Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 In some circumstances an Infrared beam fence is more appropriate than magnetic sensors i e veranda picture window balcony boundary wall e t c TTT Wireless glass break sensor can also be used see below e For a Scrolling Steel Door a special Wireless Scroll Steel Door magnetic sensor must be used due to interference of the wireless signal caused by the steel door Installation attach the larger half to the floor and attach rivet or glue the smaller half to the scroll steel door An alarm is triggered when the halves are separated by more than three to 5 00 cm witless Siqual laminas Scroll Steel Door Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 8 3 Install the wireless PIR Motion Sensor The PIR sensor will detect a person since human temperature is different to ambient temperature When triggered the PIR will signal the Control Unit Apply the detection area illustration below when installing sensor windous infrared infrared 5m 10m g 5m 10m Wireless curtain sensor detection area illustration below 8 4 Install other sensors For smoke you can use wireless smoke sensor for gas leakage detection you can install gas leakage sensor below Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 8 5 Install the Control Unit I
11. anual as below 9 1 step some wireless sensors needn t coded by manual because of we will use the learning code sensor The learning code wireless sensor you can omit the 9 1 step can be learned to the system directly like the PIR 100B and DM 100A The Wireless sensors in the package box are pre coded prior to shipping The Max Quantity of RF sensors is 16 if you need add more then you can set the wireless sensor with the same jumper Add additional wireless Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 sensors to the control units please help to see below 9 1 Prepare the RF Sensors of PT2262 IC Code 1 Prepare the RF sensors Open the back cover of the Wireless sensor carefully 2 Locate the IC boards black jumpers labeled AO A7 and DO D3 3 Configured the AO A7 and DO D3 different from each wireless sensors Includes wireless door sensor wireless smoke sensor wireless gas leakage sensor wireless pir motion sensor and so on If configured the AO A7 and DO D3 are the same the system will treat them as the same one sensor 4 Also please check the Resistors value is 3 3M Ohm there re 3 Jumpers 1 5M 3 3M and 4 7M if you select incorrect value the wireless distance usually very short or can not learn to the alarm panel 9 2 Enter the RF Sensor Adding Menu See 6 2 2 1 Add Del RF Parts Select the Zone number press Ok finished it then press OK to select the Normal Type Or Stay Type then follow
12. bute of the zone will be displayed in the LCD if this zone has been assigned wireless sensor will display V If hasn t been assigned wireless sensor means this zone is empty you can assign new wireless sensor to this zone Press Up or down button on the keyboard to check the other Zones Press Enter to edit it After you pressed the Enter button you can select the zone attribute and then press Enter you can see Turn on the device or Please trigger the new wireless sensor Then following the instruction to add the new wireless sensor to the GSM ALARM KIT 16 For Remote control it will display VVVV if the unit has been assigned remote control Both of them you can press Enter to re assign new wireless sensor or remote control to replace the existence one 3 Inthe Edit RF Parts you can edit the attribute of the sensor as Normal or Stay Type If the system is under Stay Mode Also said At House or Partial Armed the sensor set as Normal triggered will not alarm the sensor set as Stay triggered will Alarm If the system is under Armed Mode then all RF sensors triggered will alarm This is very important to remember the sensor types of the system This function is very useful when you at house and need some sensors in working status E g the sensor installed outer and gas and smoke detectors etc and some sensors indoor not in working status eg the sensors installed in the living room bed room etc 1 4 The GSM ALARM KIT
13. e panel to a failed Module connection mobile phone repairmen store and loose in then ask the engineer to check the transportation GSM Module socket and the GSM GSM Signal is too Module connection weak Please change another position to install the alarm panel Automatically 1 Backup battery with When the backup battery voltage is Restart low voltage lower than 3 7V the panel will alert by buzzer sounds Please help to contact the AC Power Wireless 1 Wireless sensor with Please replace the battery of the Sensor low voltage wireless sensor usually once year transmission 2 Wireless sensor used Please correct the resistor value to short PT2262 IC and 3 3M Ohm of the PT2262 Wireless Page OO of30 Ver 1 1 File No GSM ALARM KIT 160012 False Alarm Alarm without SMS Alarm without Dial No action after send SMS command Page incorrect Value 3 Haven t pull out wireless antenna 4 Electromagnetic interference 5 The wireless receiver in the panel with problem 1 PIR Motion sensor installation incorrect 2 Used 24H zones or SOS Zones or Watchdog zone 1 GSM Operator communication protocol 2 Haven t setup SMS Alert Auto dial Numbers 3 Caps Lock letters in the SMS Commands of 30 Ver 1 1 sensor Please pull out the wireless sensor antenna Please install the wireless sensors or alarm panel away the electric equipments Please contact
14. h supports Call ID function 2 Safety Directions Safe Startup Do not use GSM Alarm System when using GSM equipment is prohibited or might bring disturbance or danger Interference All wireless equipment might interfere network signals of GSM Alarm System and influences its performance Avoid Use at Gas Station Do not use GSM Alarm System at a gas station Power off GSM Alarm System it near fuels or chemicals Power it off near Blasting Places Please follow relevant restrictive regulations Avoid using the device in blasting places Page 0 of 30 Ver 1 1 File No GSM ALARM KIT 60012 Reasonable Use Please install the product at suitable places as described in the product documentation Avoid signal screening by covering the mainframe Use Qualified Maintenance Service Maintenance can be carried out only by qualified maintainer Waterproofness The product is not waterproof Please install it at dry places and keep it dry 3 Standard Packing List Control Unit X1 Wireless Magnetic Door Sensor X1 Wireless Remote Controls X 2 Wireless PIR Motion Sensor X1 Wired Mini Siren 110dB X1 Regulated 12VDC Power Supply X1 User Manual X1 GSM Antenna X1 Optional Accessories Wireless Sensors only PIR Motion Sensor Glass Break Sensor Magnetic Window Sensor Magnetic Steel Scrolling Door Sensor Temperature Sensor Photoelectric Beams etc 4 Physical Layout 4 1 Control Unit physical layout 1
15. he main power supply 6 This product was designed for the indoor use 7 Opening the control unit cover will avoid the warranty 8 More information will be available of the GSM ALARM KIT 16 we will not inform you again after we upgraded please check with your dealers 12 Maintenance 1 If the Control Unit works while the remote control and other sensors fail please check and change the battery 2 Ifthe remote control works but the Control Unit fails to send SMS texts switch the power of Control Unit off and switch it on after one minute Test this system after another minute or check the settings are correct and the GSM Signals are strong enough Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 3 If the Control Unit can run and sensors work but cannot send SMS texts please change SIM Card to check it 4 Ifthe problem cannot be solved please contact the distributor or manufacturer 13 Warranty 1 This system is warranted to be free of defects in material and workmanship for one year from the date of purchase 2 This warranty does not extend to any defect malfunction or failure caused by abuse or misuse by the Operating Instructions In no event shall the manufacturer be liable for any alarm system altered by purchasers 14 Trouble Shooting Guide PROBLEM POSSIBLE SOLUTION GSM Module 1 Backup battery with Please contact the AC Power initialization low voltage GSM Please help to take th
16. ing the instruction 1 Turn On the Device means trigger the RF sensor the system will show a code then on the Keyboard The system will ask you repeat the operation so please trigger RF sensor again when you see the Code then press the Enter Button on the Keyboard the system will display Saved OKI It means the wireless sensor added to the system Repeat this operation to add other wireless sensors Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 Notice a One time can add only 1 wireless sensor b The Name of the RF sensor can be modified by SMS commands Please see chapter 6 3 9 4 Add Remote Controls to the Control unit Because of both of the GSM ALARM KIT 16 and its remote controls are with learning code you can add the remote control to the GSM ALARM KIT 16 directly following the 6 2 2 1 Add Del RF Parts a Enter the Add Del RF Parts menu b Select 2 Edit Remote Ctrl then press button c then following the instruction 1 Turn On the Device means trigger the Remote Control the system will show a code then on the Keyboard The system will ask you repeat the operation so please trigger Remote Control again when you see the Code then press the Enter Button on the Keyboard the system will display Saved OK It means the Remote Control added to the system Repeat this operation to add other remote controls 1 VVVV means this serial position saved one remote control already you can learn a
17. ings 1 2 3 4 5 6 7 Please insert the SIMCard firstly and install the GSM Antenna then power on it Also you can insert the SIMCard after you setup All the wireless sensors in the standard package we have assigned to the mainframe already Needntt to learn it again After you power on the mainframe the mainframe will auto detect and display the process If it with SIMCard it will register the GSM Network and display the GSM Signal ICON in the left corner of the LCD All of the setup can be done by the LCD except modify the Zone name if you need to modify the zone name please see the command list in the related chapter Only disarm by keyboard and modify settings requires password the other operation needn t password The default password is 1234 Enter password then press Enter button to enter the system In standby mode press 3 6 following UP button The system will recovery to factory default settings the password will be 1234 But the registered wireless sensors will remain Two way communication In standby mode dial the telephone number following the Enter Button the system will dial out While incoming call press the Enter Button to answer the incoming Please note if the income calling is from the preset number then before 5 tones if answered it will create two way voice communications After 5 tones will be Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 entering
18. into wiretap status The user can listen in the alarm around sounds If the income calling is not from the preset alarm number after 5 tones if hasn t been answered will hang up 8 Ifyou want to test the two way voice communication please make sure the other phone is far from the GSM ALARM KIT 16 at least 500meters Otherwise the near cross will make lots of noise interference 6 1 Key Function Descriptions 6 1 1 Led indicator Description The GSM ALARM KIT 16 uses the icons to descript the function it will be more user friendly to user Stay Mode indicator on is in stay mode Arm Mode indicator on is in arm mode off is in disarm mode Alarm Indicator on is alarming off is normally GSM Module indicator registering will quickly flick registered successful will slowly flick Alarm link output indicator when alarm will turn on and last 4minutes Q means the alarm link output relay closing Page of30 Merl File No GSM ALARM KIT 160012 Independent output relay indicator when the independent output relay closed it will be on when the independent output relay opened will be 6 1 2 LCD ICONS Description The GSM ALARM KIT 16 uses the icons to descript the present status it will be more user friendly Enabled the Timer to arm and disarm function otherwise will not display it Timer to Arm has setup a time point to enter armed mode directly Timer to disarm Has setup a
19. isarm XxxxBB Example xxxx stands for the password 1111BB 1 4 digits Return SMS When the Password is 1111 System deactivated 7 2 3 Switch On the independent o Example 1111CC xXXXXCC xxxx stands for the password 1 4 digits Return SMS Output Relay Closed 7 2 4 Switch OFF the independent c 0 0 0 4 D D Example xxxx stands for the password 1111DD 1 4 digits Return SMS Output Relay Opened XXXXEE xxxx stands for the password 1 4 digits Return SMS Armed or At House or Disarmed AC Power is Ok or AC Power is failed Output Relay is opened Page of 30 Ver 1 1 File No GSM ALARM The Output relay status in the Return SMS is the independent output relay status It is not the alarm link Output Relay Status 8 Installation Before installing the control unit and sensors and sirens please help to test the system firstly including wireless sensor power supply gsm signal etc Please ensure the wireless sensors and electricity appliances from the mainframe more than 3 5m 8 1 Insert SIM into Control Unit and install the GSM ANT In the backside of the control unit please install the GSM SIM ard BSI The GSM ANT must be Vertical installation to ensure it in good working condition 8 2 Install the Magnetic door window sensors Magnetic door window sensors signal the Control Unit when the two parts separate by more than between 1 5 to 3 0cm Low
20. less signal 6 2 2 Setup Page of A0 Ver 1 1 File No GSM ALARM KIT 160012 To add or remove wireless sensors or remote controls and edit their attributes To setup basic parameters of the system To setup the advanced parameters of the system 6 2 2 1 Add Del RF Parts To setup the zones attribute and add new wireless sensors to specificities zone To add new remote controls To remove all registered wireless sensors and remote controls Notice ORES PAA BH SYefinition Definition The sensors with this type triggered will alarm in Armed mode Normal SE and not alarm in disarmed mode In Stay mode the sensors with Stay type triggered will alarm Stay th 24 Hour Zone In any mode the sensors with this type triggered will alarm i In the starting time point and ending time point the sensors Watchdog with this type triggered will not alarm if the sensor hasn t been triggered will make alarm In any mode the sensors with this type triggered will alarm but SOS Help not drive the siren Alarm Action when Alarm occurrence the system will Automatically dial the Pre se Auto Dial Tel Numbers for 3 times one by one and Send SMS to the Pre set SMS Alert Numbers in the meantime will drive the siren for 60seconds and close the Page of 30 Ver 1 1 File No GSM ALARM KIT 160012 link Output relay for 4 minutes 2 After you enter the menu the attri
21. n order to avoid destruction of the Control Unit by intruders please install it in a concealed location convenient to the operator If applicable ensure that an uninterruptible AC power outlet is available near the Control Unit First connect accessories to the Control Unit then the AC adapter 8 6 Install Siren Connect the Siren to the Control Unit and fix them in appropriate locations Strobe Siren Siren Light Siren 8 7 Install output relays The GSM ALARM KIT 16 with two output relays one is for SMS Control another is for alarm output Please select the one you required The SMS control output relay is useful while you re not at house then you can send SMS to switch on the light and then switch it off if you need This action will stop the intruder to break your house because of they see the light is on The Alarm Link Output Relay is for switching on the light once the alarm system triggered for 4 minutes For example when the intruder breaks the door or windows then the siren sounds and the light turn on the criminal Page of 30 Ver 1 1 File No GSM ALARM KIT will escape at once The connections please see the photo also you can use any other electric equipment to instead of the lights Please remove these plastic before you connecting the re eg ST ST Alarm Link Light SMS Control Light 9 Add Wireless Sensors to the Control Unit Notice Some wireless sensors must be coded by m
22. ower failure alert function the system will send SMS AC Power Failed 30Min to the first SMS Alert numbers after the AC power failure 30minutes if the power is recovery then will send SMS AC Power is OK Default is disabled There s no delay for Stay Mode Page of30 Ver 1 1 File No GSM ALARM KIT 160012 6 2 2 3 Advanced Setting To setup the starting time to arm and the Ending time to disarm To setup the starting and ending time to work To setup the remote control operation report function To setup the GSM Jammer Alert function Modify the system password Restore the system settings to factory defaults All of the remote controls and wireless sensors should be re assigned again Notice 1 The watchdog is special for elder or child or on duty personnel in the period Starting time point to Ending time point if this sensor hasn t been triggered the system will alarm This is very useful to monitor the elder or child goes out the bedroom or enters the kitchen to eat something Or monitor the on duty personnel in the polling period have gone to on site inspection 2 If enable the RCO alert function then when use any remote control which has been registered to the system to arm or disarm or stay operation the system will send SMS to the first SMS number 3 If enable the GSM Jammer Alert function when the GSM Signal is 0 for more than 90s the system will drive the siren for
23. ss Up Down to setup each item press move to next item Switch on or off the siren when Alarm occurrence Setup the Report time gap Range O 240Hours deflaut is 0 will not report Enable or Disable the alert function while the AC power is failure more than 30 minutes Setup the delay time after armed the system by remote control or keyboard Optional 0S 20S 30S 60S 90S Default is 30S Setup the delay time after any sensor triggered Optional OS 20S 30S 60S 90S Default is 20S 1 The SMS Alert number is for receiving the alarm SMS Message The Auto Dial Telephone number is for receiving the calling Please help to try adding country code or removing country code when you can not receive the call or SMS Because of different GSM Operator with different communication protocols Our system is with the international communications protocols 2 The Auto dial Tel Number can dial to the GSM ALARM KIT 16 6 tones later can wiretap the system site Before 6 tones if somebody answers the calling then can create two way voice communication The other telephone number can call in the GSM ALARM KIT 16 if nobody answer the calling then can not wiretap the system site if somebody answers the calling then can create two way voice communication Page of A0 Ver 1 1 File No GSM ALARM KIT 160012 3 4 9 6 For example In China the country code is 0086 please note do not write 86
24. wireless detectors only It can switch on or off one appliance by SMS command Please see below Page 0 of 30 Ver 1 1 File No GSM ALARM KIT 160012 Wireless ee mmm u vm mmm mmm SS emm mmm mm mmm Wireless et deeg ere i Antenna Y 5 Features 3 F 4 Mac z I J 5 1 The advantages of fh Ae Alarm Sys stem GSM ALARM e 1 o way Voice co ication or wiretap ale ayaildble 2 LCD displays the entire Setup menu i f cl D 3T Argh Partial Armed At House or Stay Disarmed SOS ate available Armed de den alariga sirgn wo otako Hc unictions are Programmable by user 5 atchdog 24Hours Zone sos ASRM Adem syste 6 Using cons antral ot al Arned DlSspkekbrBoauer status Siren status and GSM Signal status Gon ALARA 7 Auto detect and report GSM Signal Jammer aam SYR Switch is a Alarm Li available Page of30 Ver 1 1 File No GSM ALARM KIT 160012 8 User friendly Icons for LED indicators LCD and functional Buttons 5 2 Functions amp Features of the GSM Alarm System 1 2 CO 11 N 12 13 GSM Frequency Dual Band 900 1800MHz Quad Band is optional 850 900 1800 1900Mhz Supports armed Partial armed At House or Stay or disarmed SOS by remote control or mainframe keyboard Supports armed disarmed inquiry mainframe status switch on or off relay output by SMS Commands Automatically send
25. your distributors or manufacturer to replace it Please see the PIR Motion sensor installation user manual carefully Please check if any sensor assigned to these special zones and made incorrect activated Please setup the SMS Alert Numbers Please help to see Page 15 the sample of setup the telephone numbers Please check the commands with CAPS LOCK and correct format Also please help to change another GSM Operator SIMCard to test it File No GSM ALARM KIT 160012
Download Pdf Manuals
Related Search