RL200 (519071) Rotating Laser User Manual
Contents
1. angle that the laser is positioned from previous use and any disturbances that the unit may be sustaining 4 If the RL200 is outside of its leveling range the laser beam will flash continuously indicating that it is unable to level Please do not stare directly into the laser beam G DaveBell ELECTRONIC EQUIPMENT LIMITED 3 2 2 Set Up Vertical Mode 1 Place the RL200 onto a flat level surface with the control panel facing upwards 2 Press the Power button to turn the FRE301 on and allow it to begin its leveling process The Power indicator light will be shown indicating that the unit is on and operating 3 Once the RL200 has completed its self leveling process the laser will begin to rotate Please note that the leveling time can vary based on the angle that the laser is positioned from previous use and any disturbances that the unit may be sustaining 4 If the RL200 is outside of its leveling range the laser beam will flash continuously indicating that it is unable to level 10 G DaveBell ELECTRONIC EQUIPMENT LIMITED 3 2 3 Automatic Tilt System To enable the tilt alarm simply press the tilt alarm button on the control panel and then wait approximately 15 seconds During these 15 seconds the tilt alarm indicator light will continue to flash When the indicator light becomes constant the tilt alarm has been set 3 2 4 Directional scanning 1 Press the Speed key until it is at O r p m the laser module will stop spinni2. of the laser beam on wall A point IID Tare care that point III is as vertical as possible above or below point I The difference D of both marked points I and III on wall A amounts to the actual deviation of the plumb up beam D value should be less than 4mm 19 8 Specifications DaveBell ELECTRONIC EQUIPMENT LIMITED Accuracy 20 arc seconds 1mm 10m Self leveling range 15 Operation range With detector Indoors 25m Outdoor with detector up to 150m radius 300m diameter Four head speeds 600 300 R P M Four scan widths 10 45 90 180 Bright visible beam Wavelength 635nm Class Il IR Remote control Available distance 20 m Operation temperature 20 C 50 C 4 F 122 F Power supply DC 4 8 6V 4xsub C NI MH battery Continuance working time Approx 50hours Waterproof and dustproof IP 64 Weight 2 0kg 20
3. G DaveBell ELECTRONIC EQUIPMENT LIMITED Automatic Self leveling Rotary Laser RL200 User Manual G DaveBell ELECTRONIC EQUIPMENT LIMITED Maintenance and Safety While the instrument is operating be careful not to expose your eyes to the laser beam Direct exposure to a laser beam for a long time may be hazardous to your eyes The laser beam is equivalent to a class II Operate this laser so that the laser beam plane avoids impact on the eyes of vehicle drivers or pedestrians Do not try to dismantle the instrument Have it repaired by your dealer or supplier Dismantling yourself may worsen the problem or void your warranty When attaching the instrument to a tripod make sure the instrument is securely fixed The tripod leg clamps should be securely fastened If not securely fastened or tightened the main unit could fall off or the tripod could fall over The laser should not be stored or used in extreme temperature or during rapid temperature change The laser may not function properly if used out of the ambient temperature range Store inside the carry case and place in a dry area not subject to vibration dust or high moisture If the storage temperature and ambient temperature for usage vary significantly leave the laser in its case until it can adjust to the ambient temperature The laser should be transported or carried carefully to avoid impact or vibration The laser should be stored in the carry case and packed with c
4. cludes 5 levels 0 10 45 90 180 8 Left spinning Used when is scan mode to rotate the lasers head counterclockwise 9 Right spinning Used when is scan mode to rotate the lasers head clockwise 6 G DaveBell ELECTRONIC EQUIPMENT LIMITED 3 Directions 3 1 Battery Installation The RL200 is supplied with a rechargeable Ni MH battery pack that is located in the base of the unit It is recommended that the battery pack be completely charged before use as the RL200 battery pack does not come pre charged and charging the unit while it is operating increases the charging time The charging time when the unit is turned off is approximately 8 hours The operating time for the RL200 with a new battery pack that is at full charge is approximately 50 hours however this will decrease over time as the battery pack ages and due to the number of charges discharges that the battery pack has in its lifetime Operating time may decrease and charging time may increase based on changes in temperature where the unit is being either stored or operated The RL200 is supplied with a battery charger power adaptor in the carry case When the RL200 is low on power the power indicator light will begin to flash indicating that the battery pack should be recharged as soon as possible Indicator _ Charger G DaveBell ELECTRONIC EQUIPMENT LIMITED To charge the RL200 insert the battery charger power adaptor into the port on the battery pac
5. etween coarse and fine detection modes simply press the detection mode button on the control panel As the laser strikes the 519052 Detector sensor the speaker will beep and the LCD screen will display either an up or down arrow or a level line If the screen shows either an up or down arrow move the detector up or down the staff until the level line has been located When the level line has been located the speaker will emit a constant tone Detection Mode Symbols Coarse 5mm band Fine 3mm band G DaveBell ELECTRONIC EQUIPMENT LIMITED 7 Accuracy Checking Follow these instructions for checking axis accuracy 7 1 Horizontal surface Checking 1 Place the instrument at the point of 50m in front of wall or set a scale plate at the point of 50m away from the instrument and then adjust the level of the base approximately to aim the X1 to the wall or scale plate as depicted below H1 H2 50 Meters 14 G DaveBell ELECTRONIC EQUIPMENT LIMITED 2 Allow the unit to level and begin rotating Mark the beam position on the wall or scale plate as H1 3 Loosen the screw of the tripod and then turn the laser 180 Allow the unit to level and rotate mark the beam position on the wall or scale plate as H2 The difference between the value of H1 and H2 should be less than 10 mm 4 Repeat the same process to check your Y axis beam Again the difference between the values of the two measurements should be less than 10
6. k The light on the battery charger power adaptor has three stages Red Flashing Charger and battery are not connected Red Constant Battery is charging Green Constant Battery is charged Notices 1 Using the standard rechargeable batteries of the instrument recharging will be finished within 8 hours 4x5000mAh Ni Mh batteries 2 Power required for the charger Frequency 50 60HZ Voltage 85 265V 3 Charging and using of the instrument can progress simultaneously 4 If keeping the instrument in storage or Leave the instrument unused for a long time the batteries dry battery or rechargeable battery needs to be taken out 5 Brand new rechargeable batteries or long time unused rechargeable batteries need to be recharged and discharged three times to attain the capacity required G DaveBell ELECTRONIC EQUIPMENT LIMITED 3 2 Operations 3 2 1 Set Up Horizontal Mode 1 Attach the RL200 to a tripod that is as level as possible or place on a flat level surface Make sure that the RL200 is aligned correctly on the tripod and securely tightened in position or the unit may move during use 2 Press the Power button to turn the RL200 on and allow it to begin its leveling process The Power indicator light will be shown indicating that the unit is on and operating 3 Once the RL200 has completed its self leveling process the laser will begin to rotate Please note that the leveling time can vary based on the
7. mm 5 If the difference in either axis is more than 8mm the laser should be sent to your authorized dealer for service calibration 15 G DaveBell ELECTRONIC EQUIPMENT LIMITED 7 2 Horizontal line checking First lay down the instrument Mount the instrument on tripod between A wall and B wall Tripod near Wall A Distance should follow the instructions on illustration Switch the instrument on A E Approx 30m 16 G DaveBell ELECTRONIC EQUIPMENT LIMITED After leveling direct the laser beam onto the close wall A Mark the centre point of the laser beam on the wall Point I A E Approx 30m Turn the instrument horizontally by 180 without changing the height after leveling direct the laser beam onto Wall B Mark the centre point of the laser beam on the opposite wall B Point II 17 G DaveBell ELECTRONIC EQUIPMENT LIMITED Without turning the instrument Position it close to wall B by moving the tripod Switch on the instrument and let it leveling Approx 3om Atter leveling align tne neignt or tne instrument by using wipoa or vy unaeriaying 11 necessary In such a manner that 18 G DaveBell ELECTRONIC EQUIPMENT LIMITED the centre point of the laser beam is projected exactly located the previously marked point II on wall B A B ne I EE Approx 30m Rotate the instrument by 180 without changing the height Allow it to level in and mark the centre point
8. ng Press the Key Directional scanning the laser module will scan directionally If press the key repeatedly the angle of scanning of laser module will continuously change as follows 0 10 45 90 180 0 2 Press the Key Left spinning or the Key Right spinning to change the direction of scanning 11 G DaveBell ELECTRONIC EQUIPMENT LIMITED 4 Remote The remote control of the instrument adopts the infrared technique Aim the aperture of infrared ray to the instrument as depicted below to bring remote controlling into function Available distance indoor 30M outdoor 20M The keypad panel includes 5 keys the indicator on the RC will wink to show the operating signal has been sent out once pressing any key Operation 1 Speed Control Button press once to increase speed press again to decrease speed 2 Sleep Button turns the laser to sleep mode 3 Scanning Mode Button adjusts scanning angle from 0o to 1800 4 Rotate Left Button rotates laser left when in scan mode 5 Rotate Right Button rotate laser right when in scan mode 12 G DaveBell ELECTRONIC EQUIPMENT LIMITED 5 Detector To turn the 519052 Detector on simply press the power button on the detectors control panel The speaker will beep once and the screen will turn on indicating that the unit is operating The LCD screen on the 519052 Detector displays the battery level detection mode and if the speaker is on or off To change b
9. ushioning material Always handle the laser with care DaveBell ELECTRONIC EQUIPMENT LIMITED 1 What is included with your RL200 M G DaveBell ELECTRONIC EQUIPMENT LIMITED Your RL200 includes the following parts Main Instrument Detector and Bracket 519082 Remote Control Charger Target Glasses Hard Case with Foam Insert Please contact your supplier if any of the above parts are missing G DaveBell ELECTRONIC EQUIPMENT LIMITED 2 Find your way around the RL200 Plumb Up Beam Light House Rotating Head Optical Glass Control Panel Handle Base G DaveBell ELECTRONIC EQUIPMENT LIMITED 2 1 Control Panel Left Spin Right Spin Head Speed H I Alert Switch ON OFF 3 G DaveBell ELECTRONIC EQUIPMENT LIMITED 2 2 Utilities of Panel 1 Switch ON OFF Powers the laser up or down 2 Power indicator When the light is on the instrument is on 3 Head speed indicator Indicated the current rotational speed of the unit buy the speed that the LED flashes 4 Head speed Press this button to cycle through the various rotational speeds from 0 600rpm 5 Tilt H I alert Enabling this mode warns the user if the laser level has been jolted 6 Tilt indicator When the light is blinking slowly the laser is in H I alert mode When the light is blinking quickly the laser level will not level as it has been jolted 7 Directional scanning Circling knob Angle of scanning in
Download Pdf Manuals
Related Search