Home

USER MANUAL - CCTV Center

1. Wh Canter Arms Forward Allen Screws X SERIES USER MANUAL 2 HOW TO CONFIGURE THE CAMERA 2 1 211 2 1 2 REMOVING THE DIP SWITCH SCREW COVER There are two rows of DIP switches located behind the large screw cap see FIG 1 below Use flat bladed screw driver to remove by turning anti clockwise to unscrew CAMERA ORIENTATION FOR SETTING DIP SWITCHES CAUTION Make sure the dip switches read right way up before configuring Camera The word protocol should be displayed as per picture see FIG 2 below ON is down away from the word protocol gt OFF is up toward the word protocol The switch numbers read 1 to 8 from left to right S S i THE BAUD amp PROTOCOL SWITCHES ROW A WORK AS FOLLOWS SWITCH 1 2 3 PROTOCOL SEE 2 3 SWITCH 4 amp 5 BAUD RATE 2 4 SWITCH 6 NOT USED SWITCH 7 REAL TIME CLOCK RTC BATTERY ENABLE 2 6 SWITCH 8 RS485 TERMINATION ENABLE 2 5 Use row B FIG 2 below to set the Camera address 2 2 BEFORE SETTING DIP SWITCHES ENSURE PROTOCOL READS THIS WAY UP SEE SAMPLE BAND PROTOCOL 7485 TERMINATION CAMERA ADDRESS LEM M M E ee DEFAULT DIP SWITCH SETTINGS All X series cameras are factory defaulted to the following configuration BBV Up The Coax UTC Camera address set to 1 RS485 termination set to ON Real time clock set to ON X SERIES USER MANUA
2. 4 Redvision USER MANUAL Products Covered 0 RV X SERIES PTZ Positioning Camera RV PSU Power Supply RV ALM16 Alarm Module RV ALM16 W Wireless Alarm Module RVX 9 2 2011 Redvision CCTV Limited All rights reserved Table of Contents 1 INSTALLING THE CAMERA HEAD 1 1 CONVERT DOME TO BALL PTZ CONFIGURATION 1 2 ATTACHING CAMERA T0 BRACKET 1 3 BRACKET TYPES 1 4 HOW TO CANTILEVER BALL PTZ ARMS FORWARD HOW TO CONFIGURE THE CAMERA 2 1 REMOVING THE DIP SWITCH SCREW COVER 2 1 1 CAMERA ORIENTATION FOR SETTING DIP SWITCHES 2 1 2 DEFAULT DIP SWITCH SETTINGS 2 2 SETTING THE CAMERA ADDRESS 2 3 SETTING THE CAMERA PROTOCOL 2 4 SETTING THE CAMERA BAUD RATE 2 5 SETTING THE CAMERA RS485 TERMINATION 2 6 REAL TIME CLOCK RTC 2 7 REPLACING THE DIP SWITCH COVER POWER SUPPLY INSTALLATION 3 1 VOLTAGE 3 2 PSU INTERNAL CONNECTIONS 3 2 1 MAINS INPUT 3 22 CONNECTIONS TO CAMERA 8 WAY BLOCK 3 2 3 CONNECTIONS TO CONTROL 8 WAY BLOCK 3 24 BNC CONNECTIONS ALARM MODULE RV ALM16 4 1 INSTALLATION 4 1 1 SLIDE SWITCH 4 2 CONNECTION IDENTS AND DIP SWITCH LOCATION 4 3 ALARM INPUTS 4 3 1 ALARM INPUT GROUNDS 4 3 2 ALARM RELAY OUTPUT VOLT FREE 4 4 NORMALLY OPEN NORMALLY CLOSED ALARM INPUTS 4 5 SETTING THE ALARM MODULE RS485 TERMINATION 4 5 1 TERMINATION SCENARIOS 4 6 SETTING ALARM MODULE PROTOCOL 4 7 SETTING ALARM MODULE BAUD RATE WIRELESS ALARM CARD WIRELESS PIR DETECTOR 5 1 FACTORY FITTED WIRELESS
3. IR PODS OFF RVX IR version Camera in daylight colour mode all versions 2 Night Settings IR PODS ON RVX IR version Camera in mono all versions 8 1 DAY SETTINGS 8 1 1 SHUTTER SPEED Adjust the shutter speed to achieve greater light sensitivity Default is 1 215 LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt SHUTTER SPEED MOVE aw TO CHANGE SHUTTER SPEED 1 12 to AUTO MOVE 4 TO SAVE 8 EXIT 8 1 2 EXPOSURE COMPENSATION Adjustment for unusual lighting distribution Compensation can be either positive additional exposure or negative reduced exposure Default setting 0 LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt EXPOSURE COMPENSATION MOVE aw TO ADJUST EXPOSURE LEVEL BETWEEN 7 AND 7 MOVE 4 TO SAVE amp EXIT 8 1 3 JOYSTICK FOCUS MODE There are two settings Auto FOCUS amp manual FOCUS Default setting for day is auto LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt JOYSTICK FOCUS MODE MOVE aw TO SELECT AUTO OR MANUAL MOVE 4 TO SAVE amp EXIT 8 1 4 PRESET FOCUS MODE There are two modes auto amp stored Default setting for day is auto LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt PRESET FOCUS MODE MOVE aw TO SELECT AUTO OR STORED MOVE 4 TO SAVE amp EXIT 8 1 5 ADVANCED CONFIGURATION LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADVANCED CONFIGURATION 8 1 5 1 ZOOM LIMIT This can be adjusted from 10 t
4. The numerical value is an arbitrary figure and not a lux measurement OFF LEVEL Light level at which the IR pods turn OFF RVX IR version and the camera switches to mono Default setting is 55 must be higher than ON level LOGIN gt MAIN MENU gt NIGHT MODE gt OFF LEVEL MOVE aw CHANGE VALUE MOVE 4 TO SAVE amp EXIT AUTO IR DELAY The auto IR delay time can be set in seconds The delay prevents the IR pods amp Camera responding to short term effects e g car headlights which may cause the IR pods amp Camera to switch to mono Default is 60 seconds LOGIN gt MAIN MENU gt NIGHT MODE gt AUTO IR DELAY MOVE aw CHANGE VALUE 1 999 seconds MOVE 4 TO SAVE amp EXIT ON TIMES The IR PODS RVX IR version amp Camera can be programmed to switch on off colour mono at pre determined times There are 24 block positions representing each hour of the day LOGIN gt MAIN MENU gt NIGHT MODE gt IR ON TIMES MOVE aw TO SELECT HOUR TIME BLOCKS Solid block Infra red ON MOVE 4 TO SAVE amp EXIT No Block Infra red OFF en X SERIES USER MANUAL 7 6 INFRA RED POWER RVX IR VERSION ONLY The infra red intensity can be varied Default is set to 100 LOGIN gt MAIN MENU gt NIGHT MODE gt IR POWER MOVE aw CHANGE VALUE MOVE 4 TO SAVE amp EXIT CAMERA SETTINGS Use CAMERA SETTINGS to optimise the Sony Camera module performance for specific conditions There are two modes 1 Day Settings
5. 2 SET A PRESET USING CAMERA INTERNAL MENU 10 3 EDIT PRESETS 10 4 PRESET SPEED 10 5 TOURS 10 6 TOUR 1 TO 8 10 6 1 TOUR TITLE HOW TO PROGRAM 10 6 2 HOWTO INITIALISE A TOUR 10 63 EDIT TOUR X SERIES USER MANUAL 10 6 4 10 6 5 10 6 6 10 6 7 10 7 10 7 1 10 7 2 10 7 3 10 7 4 10 7 5 TOUR DWELL TIME SPEED TOUR ORDER FREEZE FRAME DURING SEEK RESTORE PRESET amp TOURS RESTORE TO TOUR OR PRESET NUMBER TIMED RESTORE WEEKDAY TIMED RESTORE WEEKEND RESTORE MODE RESTORE DELAY 11 PRIVACY ZONES 11 1 11 2 11 3 SET CLEAR MASK ZOOM THRESHOLD EDIT MASK 12 ALARM HANDLING IN MENU SOFTWARE 12 1 12 2 12 3 12 4 12 4 1 12 4 2 12 4 3 12 4 4 12 4 5 12 4 6 12 4 7 12 4 8 12 4 9 ENABLE DISABLE ALARMS ALARM OVER RIDE ALARM CYCLE TIME EDIT ALARMS ACTIVE TIME WEEKDAYS ACTIVE TIME WEEKENDS ACTION WHEN ACTIVE ACTION NUMBER ACTION WHEN MASKED TITLE NEW ALARM DWELL SHOW ALARM INFO CLEAR COUNTERS 13 CONTACT TECHNICAL SUPPORT 14 TECHNICAL SPECIFICATION 15 WARRANTY INFORMATION X SERIES USER MANUAL X SERIES USER MANUAL NOTES 1 INSTALLING THE CAMERA HEAD 1 1 1 2 X SERIES USER MANUAL CONVERT DOME TO BALL PTZ CONFIGURATION The RVX Series can be mounted as a dome or ball PTZ configuration To convert the dome to ball PTZ remove the M4 button head screws with 2 5mm allen key provided Se
6. 7 REPLACING THE DIP SWITCH COVER Before replacing the DIP switch screw cap it is important to check it is free of dirt and grit Thread contamination could affect the waterproof seal The thread should be carefully aligned to prevent burring Using a large flat bladed screw driver turn the screw CLOCKWISE to tighten ee 3 POWER SUPPLY INSTALLATION amp SETUP mons om Camera Warranty is void unless it is installed using one of the following Redvision power supplies Using the wrong type of 3rd party power supply could comprise safety and damage the Camera unit RV PSU RV PSU ALM16 RV PSU ALAM16 W COMPOSITE CABLE A pre made composite cable with a 7 way female amphenol connector is supplied with all Redvision brackets The female connector connects directly to the male connector on the RVX PTZ Camera housing Follow the colour coding idents as shown in table 3 2 2 for terminating the fly lead in the power supply The Redvision power supply part code RV PSU outputs 24V DC amp is supplied in a weather proof ABS box rated IP67 OBSERVE THE FOLLOWING STEPS WHEN INSTALLING THE REDVISION POWER SUPPLY 1 Mount the Redvision PSU in a position so it cannot be interfered with intentionally or accidentally Ideally use a lockable cabinet 2 Securely fix the Redvision PSU using appropriate size screws and ensure the cable glands have sufficient clearance to allow for the cables to enter it is important to ensure the glands face
7. DOWNWARDS towards the ground All cables should be channelled through the appropriate sized gland holes It is recommended that a good quality screened data pair or coax is used for transmitting data signal If the Redvision alarm module and or wireless PIR module is to be used refer to section 4 and 5 If Star configuration is used it is recommended a suitable Star Card interface is used ou FIG 7 i A Protection Plate C Locating holes for screw fixings B Accessory space for wireless alarm card 3 1 VOLTAGE Input 110V 230vac 50hz 80va max Output 24vdc 2A 3 2 PSU INTERNAL CONNECTIONS 3 2 1 MAINS INPUT TABLE 6 IDENT MAINS POWER Live Live brown 110 230Vac 50Hz 1 Neutral Neutral Blue Earth Earth yellow green BO X SERIES USER MANUAL 3 2 2 CONNECTIONS TO CAMERA 8 WAY TERMINAL BLOCK TABLE 7 IDENT UMBILICAL LEAD TO CAMERA CAM2 Not used GND Not used CAM1 Coax signal GND Coax screen RS485 A White RS485 B Orange 24V Red ov Black and cable screen 3 2 3 CONNECTIONS TO CONTROL 8 WAY TERMINAL BLOCK TABLE 8 IDENT CONTROL CONNECTIONS CAM2 Not used GND Not used CAM1 COAX signal GND COAX screen RS485 A RS485 A RS485 B RS485 B Spare GND No connection RS485 screen 3 2 4 BNC CONNECTIONS TABLE 9 IDENT BNC CONNECTIONS CAM1 BNC DVR Camera input CAM1 BNC Loop through provided for test monitor Video connections can be made either by using the B
8. Note This is a global setting for Monday through Friday TIMED RESTORE WEEKEND LOGIN gt MAIN MENU gt PRESETS amp TOURS gt RESTORE gt TIMED RESTORE WEEKEND MOVE 4 TO SELECT HOUR TIME BLOCKS MOVE aw TO SELECT ENABLE 1 DISABLE MOVE 4 TO SAVE amp EXIT Note This is a global setting for Saturday amp Sunday 10 7 4 10 7 5 X SERIES USER MANUAL RESTORE MODE PRESETS amp TOURS Use this option to make the Camera revert to a tour or preset after a specified delay period in seconds of inactivity see RESTORE DELAY 10 7 5 Restore modes LOGIN gt MAIN MENU gt PRESETS amp TOURS gt RESTORE gt RESTORE MODE MOVE aw TO SELECT OFF FIXED TOUR FIXED PRESET TIMED TOUR TIMED PRESET MOVE 4 TO SAVE amp EXIT TECH SUPPORT COMMENT Can also use timed restore weekday weekend to restore To restore to a different tour at different times see 12 4 RESTORE DELAY PRESETS amp TOURS Time taken before presets or tours are restored Select between 180 seconds amp off LOGIN gt MAIN MENU gt PRESETS amp TOURS gt RESTORE DELAY MOVE aw TO SELECT OFF or CHANGE VALUE IN SECONDS 5 180 MOVE 4 TO SAVE amp EXIT 11 PRIVACY ZONES 11 1 11 2 11 3 Up to 24 concurrent privacy zones can be programmed TECH SUPPORT COMMENT Recommended privacy patch should be set 50 larger than object being masked SET CLEAR MASK LOGIN gt MAIN MENU gt PRIVA
9. SUPPORT COMMENT Alarm module protocol should be set to the same protocol as the Camera 1 3 Pelco D normally uses 2400 baud Pelco P normally uses 4800 baud Alarm card does not support Vista amp Dennard protocols use Pelco P or D SETTING ALARM MODULE BAUD RATE Use the 8 way dip switch see D in FIG 9 page 8 to set the alarm module baud rate Set the DIP switches 5 amp 6 as per the table below to select the required baud rate 0 OFF down and 1 ON up The default setting is 9600 baud both switches off 0206 X SERIES USER MANUAL TABLE 14 PROTOCOL _ BAUD NoNC 5285 DIP SWITCH NO 2400 4800 9600 19200 CAUTION The Alarm module baud rate should be set to be the same as the Camera baud rate 2 4 5 WIRELESS ALARM CARD WIRELESS PIR DETECTOR 5 1 FACTORY FITTED WIRELESS CARD RV PSU ALM16 W The Redvision Wireless Card is compatible with the Redvision Wireless PIR Luminite Genesis Range and the Redwall Wireless Transmitter Module Part Code WF434T which wireless enables the Redwall PIRs If the POWER SUPPLY RV PSU has a factory fitted wireless alarm card RV PSU ALM16 W it will be necessary to configure the wireless alarm card s 8 WAY DIP SWITCH SETTING see FIG 10 below 1 to 3 dip switches not used amp should be left ON UP Switches 4 to 8 Dome Head Site Code provide up to 32 1 to 16 shown in TABLE 15 below channels
10. TO SAVE amp EXIT SHUTTER SPEED The shutter speed can be slowed down to increase light sensitivity Default setting 1 25 LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt SHUTTER SPEED MOVE aw TO SELECT AUTO OR MANUAL should read TO CHANGE SHUTTER SPEED 1 12 to AUTO MOVE 4 TO SAVE amp EXIT EXPOSURE COMPENSATION Adjustment for unusual lighting distribution Compensation can be either positive additional exposure or negative reduced exposure Default setting 0 LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt EXPOSURE COMPENSATION MOVE aw TO ADJUST EXPOSURE LEVEL BETWEEN 7 AND 7 MOVE 4 TO SAVE amp EXIT JOYSTICK FOCUS MODE There are two settings Auto FOCUS amp manual FOCUS Default setting for day is auto LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt JOYSTICK FOCUS MODE MOVE aw TO SELECT AUTO OR MANUAL MOVE 4 TO SAVE amp EXIT PRESET FOCUS MODE There are two modes auto amp stored Default setting for night is stored LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt PRESET FOCUS MODE MOVE aw TO SELECT AUTO OR MANUAL MOVE 4 TO SAVE amp EXIT ADVANCED CONFIGURATION LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADVANCED CONFIGURATION ZOOM LIMIT This can be adjusted from 10 to 100 LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV CONFIG gt ZOOM LIMIT MO
11. be programmed between 1 amp 120 seconds Default is 8 seconds LOGIN gt MAIN MENU gt PRESETS 8 TOURS gt TOURS gt DWELL MOVE aw TO SELECT DWELL TIME IN SECONDS MOVE 4 TO SAVE amp EXIT SPEED The speed at which the Camera moves to each preset Programmed in seconds LOGIN gt MAIN MENU gt PRESETS amp TOURS gt TOURS gt SPEED MOVE aw TO SELECT SPEED IN SECONDS MOVE 4 TO SAVE amp EXIT TOUR ORDER The speed at which the Camera moves to each preset Programmed in seconds LOGIN gt MAIN MENU gt PRESETS amp TOURS gt TOURS gt TOUR ORDER MOVE aw TO SELECT STANDARD 1 2 3 PING PONG 1 2 3 3 2 1 RANDOM MOVE 4 TO SAVE amp EXIT FREEZE FRAME DURING SEEK Freezes the last preset image until Camera moves to next preset image LOGIN gt MAIN MENU gt PRESETS amp TOURS gt TOURS gt FREEZE FRAME MOVE aw TO SELECT FREEZE FRAME MOVE 4 TO SAVE amp EXIT RESTORE PRESETS amp TOURS RESTORE TO NUMBER EITHER TOUR NUMBER OR PRESET NUMBER LOGIN gt MAIN MENU gt PRESETS amp TOURS gt RESTORE gt RESTORE TO NUMBER MOVE aw TO SELECT NUMBER 1 TO 100 IF ASSIGNING PRESET NUMBER 1 TO 8 IF ASSIGNING TOUR NUMBER MOVE 4 TO SAVE amp EXIT TIMED RESTORE WEEKDAY LOGIN gt MAIN MENU gt PRESETS 8 TOURS gt RESTORE gt TIMED RESTORE WEEKDAY gt MOVE 4 TO SELECT HOUR TIME BLOCKS MOVE aw TO SELECT ENABLE 1 DISABLE MOVE 4 TO SAVE 8 EXIT
12. compensate for poor cable runs using video lift before using video gain LOGIN gt MAIN MENU gt CAMERA SETTINGS gt VIDEO LIFT MOVE aw TO ADJUST BETWEEN 0 8 MOVE 4 TO SAVE amp EXIT DIGITAL ZOOM Select digital zoom if user wants zoom beyond optical zoom limit Default is off TECH SUPPORT COMMENT Picture degradation may occur at high zoom D LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DIGITAL ZOOM MOVE aw SELECT YES NO MOVE 4 TO SAVE amp EXIT INVERT CAMERA IMAGE TECH SUPPORT COMMENT Technicians should set the Camera orientation first see 6 4 8 INVERT CAMERA IMAGE function should only be used to correct for special cases once orientation has been set otherwise it should be set to NO LOGIN gt MAIN MENU gt CAMERA SETTINGS gt INVERT CAMERA IMAGE MOVE aw SELECT YES NO MOVE 4 TO SAVE amp EXIT MIRROR CAMERA IMAGE This function reverses the image e g left to right will appear right to left LOGIN gt MAIN MENU gt CAMERA SETTINGS gt MIRROR CAMERA IMAGE MOVE aw SELECT YES NO MOVE 4 TO SAVE amp EXIT CROSS HAIR LOGIN gt MAIN MENU gt CAMERA SETTINGS gt CROSS HAIR MOVE aw SELECT ON OFF MOVE 4 TO SAVE amp EXIT ee X SERIES USER MANUAL 9 JOYSTICK amp WIPER 9 1 9 2 9 3 9 3 1 9 3 2 9 4 9 5 9 5 1 JOYSTICK CURVE There are three settings The following options describe how sensitive the joystick i
13. outputs of the PIRs or other alarm sources 4 3 1 ALARM RELAY OUTPUT VOLT FREE Connections from the alarm relay output see C in FIG 9 above TABLE 10 ALARM RELAY OUTPUT Connect to 3rd party control alarm input if normally open signal is required Connect to 3rd party control alarm input ground Connect to 3rd party control alarm input if normally closed signal is required Bee X SERIES ER MANUAL 4 4 NORMALLY OPEN NORMALLY CLOSED ALARM INPUTS Us Use the onboard 8 way dip switch see D in FIG 9 page 8 to Select Normally Open NO 1 ON or Normally Closed NC 0 OFF dependent on whether alarm inputs are connected to sensors with normally open or normally closed outputs The default position is NORMALLY OPEN NO which is 1 ON 8 way dip switch on alarm module see D in FIG 9 page 8 TABLE 11 r PROTOCOL _ BAUD NoNC 545 DIP SWITCH NO Normally OPEN Normally CLOSED CAUTION if normally closed is selected all unused alarm inputs must be linked to ground to prevent alarms being continuously generated 4 5 SETTING THE ALARM MODULE RS485 TERMINATION Use the 8 way dip switch see D in FIG 9 page 8 to set the RS485 termination The default position is ON 1 UP OFF 0 down TABLE 12 PROTOCOL BAUD 4 NO NC DIP SWITCH NO ON OFF 4 5 1 TERMINATION SCENARIOS If control is over coax protocol both the Camera and Alarm Module shou
14. through friday ACTIVE TIME WEEKENDS LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt ACTIVE TIME WEEKEND MOVE 4 TO SELECT HOUR TIME BLOCKS MOVE aw TO SELECT ENABLE SOLID DISABLE CLEAR MOVE 4 TO SAVE 8 EXIT Note This is a global setting for saturday and sunday ACTION WHEN ACTIVE LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt ACTION WHEN ACTIVE MOVE aw TO SELECT GO TO PRESET MESSAGE ONLY SILENT OR RUN TOUR MOVE 4 TO SAVE amp EXIT ACTION NUMBER TECH SUPPORT COMMENT The Action Number is the number of the preset or tour to go depending on which option is selected LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt ACTION NUMBER MOVE aw TO SELECT NUMBER BETWEEN 1 100 MOVE 4 TO SAVE amp EXIT ACTION WHEN MASKED LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt ACTION WHEN MASKED MOVE aw TO SELECT GOTO MESSAGE ONLY OR SILENT MOVE 4 TO SAVE amp EXIT LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt TITLE MOVE aw TO SELECT ALPHNUMERIC CHARACTERS MOVE 4 TO SAVE amp EXIT ec X SERIES USER MANUAL 1247 NEW ALARM DWELL The Camera will move to a corresponding preset when a new alarm occurs On multiple alarms presets will be called up in sequence the dwell time in seconds between each alarm can be programmed Default is 5 seconds This function will be ignored if alarms
15. to user manual for the control equipment being used NB Pelco D is normally 2400 Pelco P is 4800 Dennard is 9600 TABLE 3 ROW A DIP SWITCH PROTOCOL 2 4 5 67 8 9600 0 0 2400 1 0 4800 0 1 19200 1 3 X SERIES USER MANUAL 2 5 SETTING THE CAMERA RS485 TERMINATION The default position is ON down TABLE 4 ROW A DIP SWITCH TERMINATION 3 5 7 OFF 0 ON 1 CAUTION Termination switch should be set to ON down if The Camera is being run on coax protocol The Camera is the only one connected to the twisted pair The Camera is last one on a daisy chain An alarm module has been fitted to the Camera power supply amp is running 485 protocol The termination switch should be OFF up if More than one Camera is connected on a DAISY CHAIN but it is NOT the last in line The exception would be if an alarm module were installed If this were the case the Camera should be terminated ON DOWN and the alarm module would un terminated OFF UP see section 4 5 Setting the Alarm Module RS485 Termination 2 6 REAL TIME CLOCK RTC Row A switch 7 sets the Camera s internal real time clock The RTC battery should be set to on either at commissioning or installation stage It should only be set to off if cameras in long term storage gt one month The default position is ON down TABLE 5 ROW A DIP SWITCH 2 4 G 7 8 RTC OFF 0 ON 1 2
16. CARD RV PSU ALM16 W 52 SLIDE SWITCH 5 2 1 POSITIONING OF RV PSU ALM16 W 5 3 IF RETRO FITTING WIRELESS ALARM RECEIVER NAVIGATING THE MENUS 6 1 MENU NAVIGATION FLOW CHART 6 1 1 ACCESS MAIN MENU FROM 3RD PARTY CONTROLLERS 612 EXIT MENU 6 2 LOGIN 6 3 LOGIN EXPIRY 6 4 SET UP 6 4 1 ENTER DATE amp TIME CLOCK 6 4 2 DAYLIGHT SAVING 6 4 3 LANGUAGE OPTIONS 6 4 4 DISPLAY 6 4 5 PASSWORDS 6 4 6 DATUM CHECK X SERIES USER MANUAL 10 6 4 7 CAMERA ORIENTATION 6 4 8 DATE AND TIME OF INSTALLATION 6 4 9 CLEAR SETTINGS 6 4 10 DIAGNOSTICS NIGHT MODE 7 1 IR MODE 7 2 ON LEVEL 7 3 OFF LEVEL 7 4 AUTO IR DELAY 7 5 ON TIMES 7 6 INFRA RED POWER RVX IR VERSION ONLY CAMERA SETTINGS 8 1 DAY SETTINGS 8 1 1 SHUTTER SPEED 8 1 2 EXPOSURE COMPENSATION 8 1 3 JOYSTICK FOCUS MODE 8 1 4 PRESET FOCUS MODE 8 1 5 ADVANCED CONFIGURATION 8 2 NIGHT SETTINGS 8 2 1 COLOUR MONO 8 2 2 SHUTTER SPEED 8 2 3 EXPOSURE COMPENSATION 8 2 4 JOYSTICK FOCUS MODE 8 2 5 PRESET FOCUS MODE 8 2 6 ADVANCED CONFIGURATION 8 3 VIDEO GAIN 8 4 IRIS KEY USAGE 8 5 VIDEO LIFT 8 6 DIGITAL ZOOM 8 7 INVERT CAMERA IMAGE 8 8 MIRROR CAMERA IMAGE 8 9 CROSS HAIR JOYSTICK amp WIPER 9 1 JOYSTICK CURVE 9 2 ZOOM RATIO 9 3 WIPER 9 3 1 WIPER SHORT CUT PRESET 9 3 2 WASH SHORT CUT PRESET NOT AVAILABLE YET 9 4 JOYSTICK SPEED 9 5 PAN LIMITS 9 5 1 SET RIGHT LIMIT 9 5 2 SET LEFT LIMIT 9 6 SET TILT LIMITS PRESETS amp TOURS 10 1 FOCUS SHIFT 10
17. COMMAND SET A PRESET BBV Press amp hold then press 1 Press 1 Press amp hold program key then press number preset to be saved TX400 Press amp hold then press 1 Press 1 press amp hold set then preset number BBV 1000 Press hold then press wash key Press and hold preset Press amp hold PROGRAM key then press 1 to call up menu press key 1 followed by preset key DTX 1000 Press amp hold then wash key Press and hold preset key Press amp hold set to call up then press 1 menu press key 1 followed by preset number PELCO KBD300 Enter 95 then press 8 hold preset key Enter 95 then press preset key Hold preset key then press preset number VICON Arrow keys to scroll to preset 95 Press 1 enter 6 1 2 EXIT MENU Move the joystick or arrow keys to the left from all levels to exit the Camera main menu Any changes made will be saved permanently when the menu is exited The message SAVED OK will appear to confirm changes have been saved 6 2 LOGIN Use joystick Arrow keys to navigate the menu options From main menu move joystick arrow TO LOGIN MENU MOVE 4 gt gt ENTER DIGIT PASSWORD MOVE 4 TO SAVE amp EXIT A message will display to confirm successful login or not Default PASSWORDS TECHNICIAN 999900 Full access SUPERVISOR 555500 partial access OPERATOR 111100 limited access To change a password see 6 4 5 4 amp view permissions rights see 6 4 5 6 3 LOGIN EXPIRY After 5 minutes of user
18. CONFIG gt NOISE REDUCTION MOVING MOVE a gt TO ADJUST 0 to 5 2 IS DEFAULT MOVE 4 TO SAVE amp EXIT SPOT AE LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV CONFIG gt SPOT AE MOVE a TO SELECT OFF ON OFF IS DEFAULT MOVE 4 TO SAVE amp EXIT APERTURE CORRECTION LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV CONFIG gt APERTURE CORRECTION MOVE a w TO SELECT 1 to 16 9 IS DEFAULT MOVE 4 TO SAVE amp EXIT VIDEO GAIN Video gain can be set from 0 to 7db to compensate for losses in long cable runs Default setting is 2 TECH SUPPORT COMMENT It is recommended to use video lift first before adding gain as this will usually give better results LOGIN gt MAIN MENU gt CAMERA SETTINGS gt VIDEO GAIN MOVE v TO ADJUST from 0 7 MOVE 4 TO SAVE amp EXIT ec 8 4 8 5 8 6 8 7 8 8 8 9 IRIS KEY USAGE X SERIES USER MANUAL The iris key can be assigned to either Adjust exposure compensation brighten darken image Shutter speed allows integration Can only be adjusted when Camera is in night mode IR pods on or Camera in mono LOGIN gt MAIN MENU gt CAMERA SETTINGS gt IRIS KEY USAGE MOVE aw SELECT EITHER EXPOSURE COMPENSATION SHUTTER SPEED OR OFF MOVE 4 TO SAVE amp EXIT VIDEO LIFT High frequency video lift can be set between 0 amp 8 Default is zero TECH SUPPORT COMMENT Technician should attempt to
19. CY gt SET CLEAR MASK MOVE a w TO SELECT A MASK NUMBER 1 TO 24 MOVE TO REVEAL CROSS HAIRS MOVE CAMERA TO REQUIRED VIEW USING PTZ CONTROLS SELECT ENTER COMMAND FROM CONTROL OR WAIT 15 SECS UNTIL RED PATCH APPEARS MOVE a w TO SCROLL TO NEXT MASK NUMBER REPEAT STEPS 3 TO 5 TO CREATE NEW PRIVACY MASKS MOVE 4 TO SAVE amp EXIT ZOOM THRESHOLD LOGIN gt MAIN MENU gt PRIVACY gt ZOOM THRESHOLD MOVE a 0 100 EDIT MASK LOGIN gt MAIN MENU gt PRIVACY gt EDIT MASK MOVE aw TO SELECT A MASK NUMBER 1 TO 24 TO BE EDITED CLEAR MASK a w YES NO Be X SERIES USER MANUAL 12 ALARM HANDLING IN MENU SOFTWARE 12 1 12 2 12 3 The alarms can be mapped to any preset or tour or to just put a message on the screen Within the Alarm Edit menu 12 4 use aw to select alarm number within each alarm you can set type of action dwell and time based masking for weekdays 12 4 1 amp weekends 12 4 2 The time based masking is SECONDARY to the Enable alarms menu 12 1 If the alarm is not enabled it will be completely ignored If an alarm is enabled but masked the user can then decide to set it to be silent or message only 12 4 3 Title 12 4 6 is the title or name of the alarm just like giving a preset or tour a title this will be displayed on screen when the alarm activates ALARM ACTIONS Go to preset will go to preset if set and dwell on it for dwel
20. DE 7 IR POWER CAMERA SETTINGS 8 DAY SETTING VIDEO GAN VIDEO LIFT IRIS KEY USAGE BACKLIGHT COMPENSATION DIGITAL ZOOM WHITE BALANCE WIDE DYNAMIC RANGE NOISE REDUCTION PARKED NIGHT SETTING INVERT CAMERA IMAGE NOISE REDUCTION MOVING SPOT AF APERTURE CORRECTION MIRROR CAMERA IMAGE CROSS HAIR COLOUR MONO SHUTTER SPEED BACKLIGHT COMPENSATION EXPOSURE COMPENSATION JOYSTICK FOCUS MODE NOISE REDUCTION PARKED PRESET FOCUS MODE ADVANCED CONFIGURATION X SERIES USER MANUAL JOYSTICK 9 JOYSTICK CURVE ZOOM RATIO 8 16 32 64 WIPER oom RATIO JOYSTICK SPEED PAN LIMITS TILT LIMITS SET PRESET EDIT PRESETS PRESETS amp TOURS 10 PRESET SPEED PRESET INITIALISE TOUR TOURS TOURS 1 8 EDIT TOUR RESTORE DWELL TOUR ORDER FREEZE FRAME DURING SEEK RESTORE TO NUMBER TIMED RESTORE WEEKDAY TIMED RESTORE WEEKEND PRIVACY 11 SET OR CLEAR MASK RESTORE MODE ZOOM THRESHOLD RESTORE DELAY EDIT MASK ACTIVE TIME WEEKDAY ALARMS 12 ACTIVE TIME WEEKENDS ENABLE ALARMS ACTION WHEN ACTIVE ALARM OVERRIDE TIME 0 ACTION WHEN MASKED ALARM CYCLE TIME TITLE EDIT ALARM NEW ALARM DWELL SHOW ALARM INFO CLEAR COUNTERS Vi ge ag pere X SERIES USER MANUAL Some common examples for accessing the Camera main menu and commands are as follows TABLE 16 CONTROLLER ACCESS MAIN CAMERA MENU ENTER
21. EDUCTION MOVING LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADV CONFIG gt NOISE REDUCTION MOVING MOVE aw To ADJUST 0 to 5 2 is DEFAULT MOVE 4 TO SAVE amp EXIT SPOT AE LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADV CONFIG gt SPOT AE MOVE a TO SELECT ON OFF MOVE 4 TO SAVE amp EXIT APERTURE CORRECTION LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADV CONFIG gt APERTURE CORRECTION gt MOVE aw TO SELECT 1 to 16 9 IS DEFAULT MOVE 4 TO SAVE amp EXIT 8 2 8 2 1 8 2 2 8 2 3 8 2 4 8 2 5 8 2 6 8 2 6 1 NIGHT SETTINGS X SERIES USER MANUAL The following settings apply when the IR pods are switched on RVX IR models and the Camera is in mono all models COLOUR MONO The camera default NIGHT setting is mono black amp white The camera switches to mono when the light falls below a certain level see 7 2 ON LEVEL When the camera switches to mono the infra red PODs automatically turn on IR models only However the camera can be forced to stay in colour within the NIGHT SETTINGS For this option select COLOUR TECH SUPPORT COMMENT Menu Night settings will be applied regardless of whether the camera is set to switch to MONO or stay in colour LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt COLOUR MONO MOVE aw TO SELECT AUTO OR MANUAL change to TO SELECT COLOUR OR MONO MOVE 4
22. INSTALLATION DATE TIME MOVE 4 TO SAVE amp EXIT CLEAR SETTINGS CLEAR CONFIGURATION Use this option to partially clear configuration settings All configuration changes except for tours and presets will be reset to factory default LOGIN gt MAIN MENU gt SETUP gt CLEAR SETTINGS gt CLEAR CONFIGURATION MOVE aw TO SELECT YES NO MOVE 4 TO SAVE amp EXIT CLEAR PRESETS Use this option to clear ALL stored presets LOGIN gt MAIN MENU gt SETUP gt CLEAR SETTINGS gt CLEAR PRESETS MOVE aw TO SELECT YES NO MOVE 4 TO SAVE amp EXIT CLEAR TOURS Use this option to clear ALL stored tours LOGIN gt MAIN MENU gt SETUP gt CLEAR SETTINGS gt CLEAR TOURS MOVE aw TO SELECT YES NO MOVE 4 TO SAVE amp EXIT CLEAR PRIVACY MASKS Use this option to clear ALL privacy masks LOGIN gt MAIN MENU gt SETUP gt CLEAR SETTINGS gt CLEAR PRIVACY MASKS MOVE aw TO SELECT YES NO MOVE 4 TO SAVE amp EXIT CLEAR EVERYTHING This option to clears ALL settings but does not reboot the Camera therefore leaving video picture LOGIN gt MAIN MENU gt SETUP gt CLEAR EVERYTHING MOVE aw TO SELECT YES NO MOVE 4 TO SAVE amp EXIT REBOOT To soft restart the Camera equivalent to power cycling LOGIN gt MAIN MENU gt SETUP gt CLEAR SETTINGS gt REBOOT MOVE aw TO SELECT YES NO MOVE 4 TO SAVE amp EXIT 6 4 10 X SERIES USER MANUAL DIAGNOSTICS There are five diagnos
23. L SETTING THE CAMERA ADDRESS See table TABLE 1 below for guidance on DIP switch setting for each Camera address 0 represents OFF up and 1 represents ON down TABLE 1 ROW B DIP SWITCH ROW B DIP SWITCH ADDRESS 1234567 8 KODR SS 1234567 8 not used 0 000000 0 16 0 0 0 0 1 0 0 0 1 1 0 0 00 0 O0 0 17 1 0 0 0 1 Q 0 a 2 0 100000 0 18 0 16 0 1 0 0 0 3 1 1 0 0 0 0 0 19 1 1 0 0 1 0 0 Q0 4 0 01 0090 0 0 20 0 0 1 7 0 0 0 5 1 0 1 0 0 0 0 0 21 1 0 1 0 1 0 0 0 6 0 1 1 0 0 0 0 22 0 1 1 0 1 0 0 0 7 14 1 0 0 0 0 0 23 1 1 7 0 1 0 0 0 8 0 0 0 1 0 0 0 24 6 D O 417 A1 0 Q0 O 9 10 0 1 0 O 0 25 1 00 11 0 0 0 10 0 1 01 0 0 0 0 26 0 1 0 1 1 o 0 0 id 1 1 0 1 0 0 0 0 27 1 1 0 1 1 0 0 0 12 0 0 1 1 0 0 0 28 0 0 1 1 9 0 O0 13 1 0 1 A OQ 0 O0 6 29 0 A1 1 1 0 0 0 14 0 1 1 1 9 O O 0 30 0 1 1 1 1 0 0 0 15 1 1 1 1 0 0 0 0 31 1 43 17 1 17 0 0 2 See www redvisioncctv com support downloads for camera address 32 to 255 SETTING THE CAMERA PROTOCOL On row A Set DIP switch numbers 1 2 and 3 See TABLE 2 below 1 represents ON down and 0 represents OFF up TABLE 2 ROW A DIP SWITCH PROTOCOL 2 3 4 5 6 7 8 BBV Up the Coax 0 0 0 Pelco P 0 1 0 Pelco D 1 1 0 Dennard 1 0 1 Vista O 0 1 Bosch 0 1 1 SETTING THE CAMERA BAUD RATE On row A Use DIP switch numbers 4 and 5 to set the Baud rate 0 off up amp 1 ON down See TABLE 3 below For Baud Rate settings refer
24. LM16 observe the following steps HAS PSU ALREADY GOT A 16 WAY ALARM MODULE INSTALLED If NO See steps 4 1 to 4 5 previous If YES Follow steps A to F below A ISOLATE POWER FROM PSU you cannot hot swap alarm card B Remove two off M3 fixings from Alarm PCB within highlighted OPTION PCB outline C Replace with two M3 threaded pillars supplied with wireless alarm receiver card D Align alarm module with P3 connector and secure with M3 fixings E Thread aerial antenna through gland and connect to BNC on wireless receiver F See above 5 1 FIG 13 for DIP switch settings 6 NAVIGATING THE MENUS 6 1 MENU NAVIGATION FLOW CHART Use joystick Arrow keys to navigate the menu options See FIG 12 page 13 ACCESS MAIN MENU FROM 3rd PARTY CONTROLLERS As most keyboards differ in the way they access the Camera s MAIN menu it is recommended the user refers to the specific keyboard manual for the control system they are using See FIG 12 page 8 for examples 09207 FIG 12 6 1 MENU NAVIGATION FLOW CHART ENTER DATE TIME DAYLIGHT SAVING LANGUAGE DISPLAY PASSWORDS MAIN MENU LOG IN DATUM CHECK HANGING ARMS OUT CAMERA ORIENTATION SET UP 6 4 UPRIGHT INSTALLATION DATE ARIE Ol CLEAR SETTINGS CLEAR CONFIGURATION DIAGNOSTICS CLEAR PRESETS CLEAR TOURS CLEAR PRIVACY ON LEVEL CLEAR ALARM SETTINGS OFF LEVEL CLEAR EVERYTHING AUTO IR DELAY REBOOT ON TIME SHUTTER SPEED EXPOSURE COMPENSATION NIGHT MO
25. NC or screw terminal blocks 4 ALARM MODULE RV ALM16 4 1 INSTALLATION If the alarm module RV ALM16 has not been factory fitted refer to separate installation guide supplied with alarm module CAUTION Alarm module does not support Vista and Dennard protocols Use Pelco P or D or BBV UTC 007 X SERIES USER MANUAL 4 1 1 SLIDE SWITCH CAUTION When an alarm module is fitted to the power supply make sure the slide switch on the power supply is set to yes Otherwise the alarm activations will not be seen See FIG 8 below Also make sure the alarm module s protocol see 4 5 termination see 4 6 amp baud rate 4 7 match the PTZ dome s otherwise the alarms will not work FIGS OPTION PCB FITTED NO YES L n 4 2 CONNECTION IDENTS AND DIP SWITCH LOCATION If the alarm module RV ALM16 has not been factory fitted refer to separate installation guide supplied with alarm module Alarm Inputs 1 to 16 Alarm grounds 1to 16 Alarm relay output Dip switch settings Protocol 1 4 baud rate 5 normally open closed 7 RS485 Termination 8 4 3 ALARM INPUTS See A in FIG 9 above 1 16 sets of volt free Contacts which can be configured using the onboard 8 way dip switch see D above for either normally open or normally closed operation 4 3 1 ALARM INPUT GROUNDS See B in FIG 9 above All alarm input grounds are common amp connected together and may be used for
26. RA TITLE SCREEN POSTION LOGIN gt MAIN MENU gt SETUP gt DISPLAY gt CAMERA TITLE gt POSITION ON SCREEN MOVE aw TO MOVE SCREEN POSITION MOVE 4 TO SAVE amp EXIT SHOW PRESET TITLES DURING TOURS LOGIN gt MAIN MENU gt SETUP gt DISPLAY gt SHOW PRESET TITLE DURING TOURS MOVE aw SELECT YES NO MOVE 4 TO SAVE amp EXIT PRESET TEXT POSITION LOGIN gt MAIN MENU gt SETUP gt DISPLAY gt SHOW PRESET TEXT POSITION MOVE aw TO CHANGE POSITION MOVE 4 TO SAVE amp EXIT TECH SUPPORT COMMENT It is important users do not set everything to the same corner of the screen 6 4 4 6 6 4 5 6 4 5 1 6 4 5 2 6 4 5 3 6 4 5 4 6 4 6 X SERIES USER MANUAL TEXT BACKGROUND LOGIN gt MAIN MENU gt SETUP gt DISPLAY gt TEXT BACKGROUND MOVE aw SELECT TO CHANGE TEXT BACKGROUND MOVE 4 TO SAVE amp EXIT PASSWORDS LOGIN gt MAIN MENU gt SETUP gt PASSWORDS OPERATOR LIMITED ACCESS Default password is 111100 TO CHANGE see 6 4 5 4 Permission rights Date time Daylight saving Presets Tours Display options Language options Datum check SUPERVISOR PARTIAL ACCESS Default password is 555500 TO CHANGE see 6 4 5 4 Permission rights All operator permissions plus Clear privacy Set privacy Alarms TECHNICIAN FULL ACCESS Default password is 999900 TO CHANGE see 6 4 5 4 Permission rights All operator amp supervisor permissions plus Camera titl
27. T MOVE aw TO SELECT ON OFF MOVE 4 TO SAVE amp EXIT 10 PRESETS amp TOURS Presets and tours can be programmed using third party keyboard controllers or from the Camera s own internal menu To access presets amp tours menu LOGIN gt MAIN MENU gt PRESETS amp TOURS 10 1 FOCUS SHIFT LL SEE S SSE SEE S SS SS SGK I II I CCC I II TECH SUPPORT COMMENT Technicians will be familiar with setting up focus on a fixed Camera by temporarily fitting the lens with a neutral density nd filter to compensate for focus shift when the Camera switches to mono The best way to ensure optimum focus on a dome ptz Camera is to set night time presets when the light levels are low and the Camera is in mono amp the IR pods are on RVX IR versions only The controller s focus near focus far can be used to fine tune the focus manually before saving the preset This way the Camera will remember an absolute preset position including the focus settings 2 10 2 SET A PRESET USING CAMERA INTERNAL MENU LOGIN gt MAIN MENU gt PRESETS amp TOURS gt PRESETS gt SET PRESETS MOVE a w TO SELECT PRESET NUMBER TO BE SAVED 1 100 NUDGE JOYSTICK ARROW right TO PRODUCE COSSHAIR USE PTZ CONTROL TO MOVE CAMERA INTO POSITION USE ENTER OR CANCEL TO QUIT OR WAIT 10 SECS FOR PRESET TO AUTO SET REPEAT STEPS 4 TO 6 TO SET MORE PRESETS MOVE 4 TO SAVE amp EXIT v V Vv V V V V 10 3 EDIT PRESET T
28. TO SELECT A TOUR NUMBER 1 8 MOVE aw TO CHANGE VALUE MOVE lt TO SAVE amp EXIT TOUR TITLE HOW TO PROGRAM Each tour can be assigned its own title The default title is t1 t2 t3 etc LOGIN gt MAIN MENU gt PRESETS amp TOURS gt TOURS gt TOUR TITLES TOUR MOVE TO INPUT TITLE MOVE aw TO SELECT A TOUR NUMBER TO BE NAMED MOVE aw TO SELECT ALPHANUMERIC CHARACTERS MOVE 4 TO SAVE amp EXIT HOW TO INITIALISE A TOUR LOGIN gt MAIN MENU gt PRESETS amp TOURS gt TOURS gt INITIALISE TOUR MOVE aw TO SELECT EITHER CANCEL DOES NOTHING 8 LEAVES TOUR IN TACT CLEAR REMOVES PRESETS FROM TOUR OR SET POPULATES THE TOUR WITH ALL SET PRESETS IN ORDER MOVE 4 TO SAVE amp EXIT EDIT TOUR Allows operator to edit the standard tour sequence e g preset 1 2 3 The default setting is position 1 of the tour preset 1 and position 2 preset 2 etc The tour can be edited so that position 1 could preset 2 for example any positions set to NO preset will be ignored when the tour is running TECH SUPPORT COMMENT Note that any positions set to empty presets will be skipped LOGIN gt MAIN MENU gt PRESETS amp TOURS gt TOURS gt EDIT TOUR MOVE aw SELECT TOUR TO BE EDITED MOVE 4 TO SAVE amp EXIT Be 10 6 4 10 6 5 10 6 6 10 6 7 10 7 10 7 1 10 7 2 10 7 3 X SERIES USER MANUAL TOUR DWELL TIME The time the Camera dwells between each preset can
29. VE aw TO ADJUST ZOOM LIMIT BETWEEN 10 and 100 MOVE 4 TO SAVE amp EXIT 092072 8 2 6 2 8 2 6 3 8 2 6 4 8 2 6 5 8 2 6 6 8 2 6 7 8 2 6 8 8 2 6 9 8 3 X SERIES USER MANUAL BACKLIGHT COMPENSATION The ability of a Camera to compensate in cases where a subject with a large amount of background light would otherwise be obscured by blooming or silhouetting LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV CONFIG gt BACKLIGHT COMPENSATION MOVE a TO SELECT ON OFF MOVE 4 TO SAVE amp EXIT IMAGE STABILISER LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV CONFIG gt IMAGE STABILISER MOVE a w TO SELECT ON OFF MOVE 4 TO SAVE amp EXIT WHITE BALANCE LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV CONFIG gt WHITE BALANCE MOVE a gt TO SELECT OUTDOOR AUTO ATW OUTDOOR INDOOR AUTO SODIUM LAMP SODIUM LAMP AUTO MOVE 4 TO SAVE amp EXIT WIDE DYNAMIC RANGE LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV CONFIG gt WIDE DYNAMIC RANGE MOVE a w TO SELECT OFF AUTO ON MOVE 4 TO SAVE amp EXIT NOISE REDUCTION PARKED LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV CONFIG gt NOISE REDUCTION PARKED MOVE a gt TO ADJUST 0 to 5 2 IS DEFAULT MOVE 4 TO SAVE amp EXIT NOISE REDUCTION MOVING LOGIN gt MAIN MENU gt CAMERA SETTINGS gt NIGHT SETTINGS gt ADV
30. are connected directly to third party control equipment rather than the Redvision alarm module TECH SUPPORT COMMENT See ALARM OVER RIDE 12 2 and ALARM CYCLE TIME 12 3 the new alarm dwell defines how long the Camera will stay on a new alarm when cycling through the active alarms list LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt NEW ALARM DWELL TIME MOVE aw TO CHANGE VALUE BETWEEN 1 20 SECONDS MOVE 4 TO SAVE amp EXIT 12 4 8 SHOW ALARM INFO The Camera will move to a corresponding preset when a new alarm occurs On multiple alarms presets will be called up in sequence the dwell time in seconds between each alarm can be programmed Default is 5 seconds This function will be ignored if alarms are connected directly to third party control equipment rather than the Redvision alarm Module TECH SUPPORT COMMENT Also includes number of activations which could be useful for tracking down chattering alarms LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt SHOW ALARM INFO ALARM INFO INCLUDES ALARM NUMBER ENABLED Y N ACTIVE Y N MASKED Y N ACTION WHEN ACTIVE LAST ACTIVATION MOVE 4 TO SAVE amp EXIT 12 4 9 CLEAR COUNTERS LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt CLEAR COUNTERS MOVE aw TO SELECT YES OR NO MOVE 4 TO SAVE amp EXIT ec 13 CONTACT TECHNICAL SUPPORT Mon Redvision Technical Support Helplin
31. e FIG A below UNSCREW BUTTON SCREWS to remove dome lid ALIGN LOCKING NUT within cutout OBSERVE THE FOLLOWING PRECAUTIONS WHEN INSTALLING 1 Mount the Camera in a position where it cannot be be interfered with either intentionally or accidentally 2 The mounting surface should be capable of supporting the weight of both the Camera and mounting brackets under all expected conditions of load vibration and temperature 3 The mounting brackets should be fitted in accordance with instructions and should observe all appropriate safety precautions amp local building regulations 4 Ensure the Camera is in the correct orientation see FIG B above ATTACHING CAMERA TO BRACKET BRACKET INSTALLATION Fixings to the various bracket types will depend on the fixing surface It is important to use adequate quality fixings to safely support the complete Dome Ball PTZ assembly Fixing slots on a 4 PCD provide adequate clearance for 6mm bolts if attaching the Pedestal or Swan Mount to the mast FLYING LEAD If using a Swan Pedestal Pendant Mount install the Fly Lead optionally through the Central Mounting Tube or via a 20mm Gland Entry Point The Gland Entry is supplied with a 20 x 1mm thread to accomodate industry standard 20mm Glands ee X SERIES USER MANUAL ATTACHING CAMERA TO THE BRACKET See Fig C amp D below 1 Remove Mount Cover Plate 6 2 Fully unscrew Hand Lock Nut 3 Offer Camera to Bracket The Mounting Boss orie
32. e over riding the operator s joystick commands and moving to alarm action The over ride time can be set to between 1 and 20 seconds default is 10 seconds LOGIN gt MAIN MENU gt ALARMS gt ALARM OVERIDE TIME MOVE aw TO CHANGE VALUE 1 20 SECS MOVE 4 TO SAVE 8 EXIT ALARM CYCLE TIME The alarm cycle time programmed in seconds is the time it takes to tour the presets of still active alarms Default is 3 seconds This function will be ignored if alarms are connected directly to third party control equipment rather than the Redvision Alarm Module RV PSU ALM 16 amp RV PSU ALM16 W LOGIN gt MAIN MENU gt ALARMS gt NEW ALARM CYCLE TIME MOVE aw TO CHANGE VALUE 1 20 SECS MOVE 4 TO SAVE amp EXIT 12 4 12 4 1 12 4 2 12 4 3 12 4 4 12 4 5 12 4 6 X SERIES USER MANUAL EDIT ALARMS Use this menu to program how alarms are configured e g Create a weekday time schedule when alarms are automatically enabled or disabled and the type of action required when an alarm is enabled amp subsequently activated etc Alarm dwell 12 4 7 time can also be programmed in the menu LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt ACTIVE TIME WEEKDAYS LOGIN gt MAIN MENU gt ALARMS gt EDIT ALARMS gt 1 16 gt ACTIVE TIME WEEKDAYS MOVE 4 TO SELECT HOUR TIME BLOCKS MOVE aw TO SELECT ENABLE SOLID DISABLE CLEAR MOVE 4 TO SAVE amp EXIT Note This is a global setting for monday
33. e tel 44 0 1420 448 448 email support redvisioncctv com web www redvisioncctv com support 14 TECHNICAL SPECIFICATION CAMERA TELEMETRY Image sensor Sony EXview 1 4 HAD CCD PS RS485 Pelco P Pelco D Vista Dennard amp Bosch Model FCB EX490E P FCB EX985 E P FCB EX1020 P Coax BBV Optical zoom RVX18x Optical RVX28x Optical RVX36x Optical Addressing DIP switch Digital zoom 12x 12x 12x Baud rate 9600 4800 or 2400 Horizontal resolution 550TVL 550TVL 550TVL Ange of ou 28 48 220 542 1 57 Focal Length 4 1 to 73 8mm 3 5 91 0mm 3 5 91 0mm F1 4 to F3 F1 6 to F3 8 F1 6 to F3 8 Left amp Right Pan Limits Programmable Min illumination 0 7 1x F1 4 50IRE 0 25 1x F1 35 50IRE 1 4 1x F1 6 50IRE Pan amp Tilt Continuous 360 Pan 0 1 200 per second Tilt 60 to 90 depending on set up INFRA RED ILLUMINATION RVX I version KEY FEATURES IR wavelength 850nm semi covert Presets Tours 100 presets with programmable 940nm covert wavelength available to special order titles amp 8 tours with programmable titles IR range Tested to 100m 850nm Password protection Yes three levels Camera titles 16 alphanumeric characters ENVIRONMENTAL amp PHYSICAL Preset titles 16 alphanumeric characters Privacy zones 24 programmable Camera head material Die cast aluminium Alarm handling Weekend weekday time Window Flat toughened glass schedules for enable ing disabling Operating temperature 35 C to 50 C heater Fan alarms Camera head Weig
34. es Set passwords Installation date Clear settings Reboot Diagnostics R modes Camera settings Joystick settings Wiper settings TO CHANGE PASSWORD LOGIN gt MAIN MENU gt SETUP gt PASSWORDS LOGIN USING TECHNICIAN PASSCODE MOVE 4 aw TO SELECT LEVEL TO BE CHANGED MOVE 4 aw TO CHANGE PASSWORD NUMBER MOVE 4 TO SAVE amp EXIT DATUM CHECK The Redvision X Series Camera is programmed to perform a datum check every 24 hours The Camera will pan and tilt for a few seconds while it undergoes a self diagnostic test and re checks its alignment When the process is complete the Camera will revert to its previous activity including any tours with presets TECH SUPPORT COMMENT It is recommended to leave the Camera in the default 24 hour option e 6 4 7 6 4 8 6 4 9 6 4 9 1 6 4 9 2 6 4 9 3 6 4 9 4 6 4 9 5 6 4 9 6 X SERIES USER MANUAL CAMERA ORIENTATION LOGIN gt MAIN MENU gt SETUP gt CAMERA ORIENTATION MOVE aw TO SELECT CAMERA ORIENTATION gt HANGING HANGING ARMS OUT UPRIGHT UPRIGHT ARMS OUT MOVE 4 TO SAVE amp EXIT The Camera orientation automatically sets the maximum tilt up down positions depending on whether the Camera is in upright or hanging down mode The maximum tilt restrictions can be deactivated to allow full tilt movement See 9 6 DATE AND TIME OF INSTALLATION LOGIN gt MAIN MENU gt SETUP gt INSTALLATION DATE MOVE 4 aw TO ENTER
35. he default display title for a preset is P1 P2 P3 etc To customise preset titles LOGIN gt MAIN MENU gt PRESETS amp TOURS gt PRESETS gt EDIT PRESETS MOVE w TO SELECT PRESET NUMBER TO BE EDITED USE TO INPUT TITLE OR CLEAR PRESET USE a w TO SELECT ALPHANUMERIC CHARACTERS gt gt gt MOVE 4 TO SAVE amp EXIT ee 10 4 10 5 10 6 10 6 1 10 6 2 10 6 3 PRESET SPEED X SERIES USER MANUAL The speed at which the Camera moves to each preset can be programmed Default is 60 to change the value LOGIN gt MAIN MENU gt PRESETS amp TOURS gt PRESETS gt PRESET SPEED MOVE aw TO SELECT PRESET MOVE aw TO CHANGE VALUE 10 TO 100 MOVE 4 TO SAVE amp EXIT TOURS Tour 1 by default is fully populated amp includes all set presets It is possible to program up to 100 presets per tour Once a tour is set the Camera moves between each preset within that tour automatically and will dwell 10 6 4 for a period specified The restore tour mode 10 7 can be activated on any tour from 1 to 8 The tour is continually repeated unless interrupted by Manual pan tilt or zoom Calling up a preset position An alarm activation TOUR 1 TO 8 The user can set up to 8 different tours Tour 1 by default is fully populated amp includes all set presets These can be edited if required All other tours are empty LOGIN gt MAIN MENU gt PRESETS 8 TOURS gt TOURS TOUR MOVE aw
36. ht 6 5 Kilos Video launch amplifier 0 6dB 8 steps Paint finish Powder coat Heater Yes IP Rating IP66 Fan Yes WIPER Optionally available on all models OPTIONAL ALARM MODULE Intermittent or Wiper Time Out Features 16 Alarm inputs volt free 1 relay o p fits to RV PSU Optional wireless card up to 16 PIRs POWER CONSUMPTION MOUNTING BRACKETS Input 110V to 240Vac 50MZ Type Pedestal Swan pedestal tower Output 24V DC 2A output mount wall corner pendant amp Power Consumption 2 Amps at 48VA pole clamp This product is C marked and has been fully tested and complies with 2004 108 eec Electromagnetic Compatibility 73 23 eec Low Voltage Directives 60950 2006 Safety Standards 15 WARRANTY INFORMATION n m Redvision CCTV Limited Redvision warrants the buyer that the product will on the date of shipment be free from defects in material amp workmanship and will conform to Redvision s specifications provided to the buyer If any defect in material or workmanship appears in the product Redvision will at its option either repair or replace the defective product without charge at Redvision s customer service centre or serviced authorised repair facility or credit or refund the purchase price of the defective product provided The defect appears within 24 months from the date of purchase by the end user Examination of the product confirms that the claimed defect actually exists Buyer shall follow Redvision s instruc
37. inactivity the system times out and the Camera reverts to its previous activity Access to the menu will be denied unless password is re entered 6 4 SET UP The SET UP is the main sub menu for accessing Camera configuration settings See 6 4 1 to 6 4 10 Login gt main menu gt set up 6 4 1 ENTER DATE amp TIME LOGIN gt MAIN MENU gt SETUP gt ENTER DATE TIME MOVE 4 aw TO SET DATE DD MM YY 8 TIME HH MM SS MOVE 4 TO SAVE amp EXIT 6 4 2 6 4 3 6 4 4 6 4 4 1 6 4 4 2 6 4 4 3 6 4 4 4 6 4 4 5 X SERIES USER MANUAL DAYLIGHT SAVING Default setting is AUTO LOGIN gt MAIN MENU gt SETUP gt DAYLIGHT SAVING MOVE 4 aw TO SET Auto OFF 0 ON 1 MOVE 4 TO SAVE amp EXIT LANGUAGE OPTIONS Localise the display messages into the following language options English Spanish German French Portuguese LOGIN USING TECHNICIAN PASSCODE gt MAIN MENU gt LANGUAGES MOVE aw TO CHANGE LANGUAGE MOVE 4 TO SAVE amp EXIT DISPLAY DATE TIME POSITION User has the option of inserting the on screen position of the date time LOGIN gt MAIN MENU gt SETUP gt DISPLAY gt DATE amp TIME POSITION MOVE aw TO MOVE THE DISPLAY POSITION MOVE 4 TO SAVE 8 EXIT Default is OFF nothing displayed CAMERA TITLE LOGIN gt MAIN MENU gt SETUP gt DISPLAY gt CAMERA TITLE gt TITLE MOVE aw TO CHANGE ALPHANUMERIC CHARACTERS MOVE 4 TO SAVE amp EXIT CAME
38. l seconds Otherwise it will just display alarm title if set or alarm number if not on screen for dwell before moving on Go to tour will invoke the selected tour if set for dwell seconds Otherwise it will just display alarm title if set alarm number if not on screen for dwell before moving on It is down to the user to ensure that the alarm dwell time gives sufficient time to run the tour or as much of the tour as they require Message only will display alarm title if set number if not on screen for dwell seconds before moving on Silent will do nothing and move on instantly When all alarms are cleared 12 4 9 the Camera will be pointing at wherever the last preset was or running the last tour This will continue until either the user moves the Camera or the restore option 10 9 if set kicks in ENABLE DISABLE ALARMS Alarms need to be enabled in order to function correctly This feature can also be used to disable nuisance alarms caused by faulty alarm input devices such as PIRs The alarm default setting is all alarms enabled block LOGIN gt MAIN MENU gt ALARMS gt ENABLE ALARMS MOVE 4 gt TO SELECT ALARM NUMBER 1 TO 16 MOVE aw TO ENABLE BLOCK DISABLE CLEAR MOVE 4 TO SAVE amp EXIT ALARM OVER RIDE On alarm activation the Camera automatically switches to the preset view of the most current alarm The alarm overide is the time the Camera will wait befor
39. ld be terminated TERMINATED o Ter a DVR COA pp i RV DOME On PSU TERMINATED If control is over RS485 and the system is running a Star Card configuration both the Camera and Alarm Module should be terminated RV DOME TERMINATED KJ I DVR RV DOME TI TERMINATED www 4 6 4 7 X SERIES USER MANUAL If control is over RS485 and the system is running a Daisy Chain configuration then A If the Camera and Alarm Module is the last in line both the Camera and Alarm Module should be terminated RV DOME RV DOME RV DOME UN TERMINATED UN TERMINATED TERMINATED DVR RS 485 DAISY CHAIN U d 8 5 f b PSU amp 20 la la B If the Camera and Alarm Module is NOT the last in line the Camera should be terminated and the Alarm Module un Terminated The Alarm Module takes over the termination from the Camera i e it the Alarm Module should be un terminated RV DOME RV DOME RV DOME RV DOME UN TERMINATED TERMINATED UN TERMINATED TERMINATED RS 485 DAISY CHAIN END OF LINE PSU ge a 1 i a UN Te 6 SETTING ALARM MODULE PROTOCOL From the 8 way DIP switch see D in FIG 9 page 8 set the alarm module protocol Set DIP switches 1 2 3 amp 4 as per the table below required protocols 1 on up amp 0 off down TABLE 13 DIP SWITCH NO BBV UP THE COAX PELCO P PELCO D TECH
40. mited Redvision CCTV Limited 17 Highview business park High Street Bordon Hampshire GU35 United Kingdom Company registration UK3952814 www redvisioncctv com et X SERIES USER MANUAL LI Redvision
41. n pre defined left and right limits This can be useful if the Camera is mounted on the corner of a building or a wall If presets are programmed the Camera will stay within the permitted limits and not take the shortest route LOGIN gt MAIN MENU gt JOYSTICK gt PAN LIMIT gt SET PAN LIMITS MOVE aw TO SELECT ON OFF MOVE 4 TO SAVE amp EXIT TECH SUPPORT COMMENT If re setting LEFT amp RIGHT PAN limits the technician should turn use limits off to allow full movement SET RIGHT LIMIT LOGIN gt MAIN MENU gt JOYSTICK gt PAN LIMIT gt SET RIGHT PAN LIMIT gt PAN THE CAMERA TO THE RIGHT MOST PAN LIMIT PRESS SELECT OR WAIT 10 SECS FOR AUTO SET MOVE 4 TO SAVE amp EXIT ee X SERIES USER MANUAL 9 5 2 SET LEFT LIMIT LOGIN gt MAIN MENU gt JOYSTICK gt PAN LIMIT gt SET LEFT PAN LIMIT PAN THE CAMERA TO THE LEFT MOST PAN LIMIT gt PRESS SELECT OR WAIT 10 SECS FOR AUTO SET MOVE 4 TO SAVE amp EXIT 9 6 SET TILT LIMITS Default setting is on Limits are determined by the Camera Orientation set up see 6 4 7 All X Series Cameras have the following viewing tilt angle In Dome configuration i e with lid 90 to 10 above horizon In Ball configuration i e without lid 90 to 60 above horizon Default tilt setting is ON Limits are determined by the Camera orientation setup See 6 4 7 LOGIN gt MAIN MENU gt JOYSTICK gt TILT LIMIT gt SET TIL
42. ntation is important and should match the picture in FIG C amp D below i e The Flat Edge should be positioned to the rear and the Retaining Lugs engaged in the Boss Cut Outs 4 If RV PED Pedestal is being used support the Camera with hand when tightening the Hand Lock Nut ensure the Hand Lock Nut is fully tightened 8 5 Ensure the Clearance is even throughout 360 rotation and the Camera is free moving 6 Replace Mount Cover Plates Clearance Hand Lock Nut Mounting Boss Flat Edge 1 3 BRACKET TYPES RV SWAN Swan mount RV WALL Wall mount RV PNDT Pendant mount RV PED Pedestal for mast tower mount TECH SUPPORT COMMENT It is important to match the menu software settings to the Camera orientation 6 4 7 i e is the Camera hanging down or upright hanging down would be using one of the following bracket types swan RV SWAN pendant RV PNDT or wall RV WALL NOT SUITABLE FOR UPRIGHT MOUNTING Upright would be using the pedestal bracket RV PED ii 1 4 HOW TO CANTILEVER BALL PTZ ARMS FORWARD 1 Remove pear shaped badge on each arm using small flat head screw driver Slightly loosen by one turn BUT DO NOT REMOVE the allen screws Cantilever the Ball Arms forward to STOP position Tighten allen screws Replace badges spares are provided See Section 6 4 7 and from the SET UP MENU select either UPRIGHT ARMS OUT or HANGING ARMS OUT
43. o 100 LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ZOOM LIMIT MOVE aw TO CHANGE ZOOM LIMIT 10 to 100 MOVE 4 TO SAVE amp EXIT 8 1 5 2 8 1 5 3 8 1 5 4 8 1 5 5 8 1 5 6 8 1 5 7 8 1 5 8 8 1 5 9 X SERIES USER MANUAL BACKLIGHT COMPENSATION The ability of a Camera to compensate in cases where a subject with a large amount of background light would otherwise be obscured by blooming or silhouetting Can be turned ON or OFF Default is off LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADV CONFIG gt BACKLIGHT COMPENSATION MOVE aw TO SELECT ON OFF MOVE 4 TO SAVE amp EXIT IMAGE STABILISER LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADV CONFIG gt IMAGE STABILISER MOVE aw TO SELECT ON OFF MOVE 4 TO SAVE amp EXIT WHITE BALANCE LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADV CONFIG gt WHITE BALANCE MOVE aw TO SELECT OUTDOOR AUTO ATW OUTDOOR INDOOR AUTO SODIUM LAMP SODIUM LAMP AUTO MOVE 4 TO SAVE amp EXIT WIDE DYNAMIC RANGE LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADV CONFIG gt WIDE DYNAMIC RANGE MOVE aw SELECT OFF AUTO ON MOVE 4 TO SAVE amp EXIT NOISE REDUCTION PARKED LOGIN gt MAIN MENU gt CAMERA SETTINGS gt DAY SETTINGS gt ADV CONFIG gt NOISE REDUCTION PARKED MOVE aw TO ADJUST 0 to 5 2 IS DEFAULT MOVE 4 TO SAVE amp EXIT NOISE R
44. of wireless transmission to enable alarm activation The transmission needs to be matched between the Dome Head Site Code on the wireless receiver amp the Site Code within the PIR detector see separate PIR installation guide supplied with the PIR One or more domes wil respond to any wireless PIR within range providing the Dome Head Site Code amp corresponding PIR Site Code match METAL COVER TABLE 15 NOT USED SW1 42 3 4 5 6 7 8 UP 1 A A A A A A A A DOWN V 2 A A A A A A A Y 3 A A A A A A Y A 4 A A A A A A Y Y 5 A A A A A V A A 6 A A A A A Y A Y WIRELESS RECEIVER 7 A A A A A v v A 8 A A A A A Y Y Y 8 WAY DIP SWITCH 9 A A A A v A A A niger 10 A A A A Y A A Y 11 A A A A Y A Y A 12 A A A A Y A Y Y 13 A A A A Y Y A A 14 A A A A Y VAY 15 A A A A Y Y Y 16 A A A A Y Y Y Y met 5 2 5 2 1 5 3 SLIDE SWITCH X SERIES USER MANUAL CAUTION Ensure the slide switch located on the power supply PCB is set to YES See FIG 11 below FIG 11 POSITIONING OF RV PSU ALM16 W To maximise the transmission range install the PSU externally with the aerial pointing through the gland towards the ground An optional booster aerial RV AE434 can be used to significantly improve signal and range It is recommended to use the booster aerial if the PIRs are installed on metal clad buildings IF RETRO FITTING WIRELESS ALARM RECEIVER If retro fitting a wireless alarm receiver card onto an existing 16 way alarm module RV A
45. s to small movements Linear is most sensitive quasi linear and non linear allow for finer control at low speeds ramping up with larger movements Quasi linear is the default LOGIN gt MAIN MENU gt JOYSTICK gt JOYSTICK CURVE MOVE aw TO SELECT QUASI LINEAR LINEAR OR NON LINEAR MOVE 4 TO SAVE amp EXIT ZOOM RATIO The zoom ratio affects how much the Camera slows down as you zoom in the higher the numbers make the speed drop off more as you zoom in The default setting is 16 LOGIN gt MAIN MENU gt JOYSTICK gt ZOOM RATIO MOVE av 8 16 32 64 MOVE 4 TO SAVE amp EXIT WIPER Applies to RVX models fitted with wiper LOGIN gt MAIN MENU gt JOYSTICK gt WIPER MOVE aw INTERMITTENT WIPE 1 99 OR WIPER TIMEOUT 1 255 MOVE aw TO CHANGE TIME IN SECONDS WIPE 1 99 TIMEOUT 1 255 MOVE 4 TO SAVE amp EXIT WIPER SHORT CUT PRESET If the control unit does not have a dedicated wiper key function it is possible to allocate a PRESET number to activate deactivate the wiper LOGIN gt MAIN MENU gt JOYSTICK gt WIPER gt WIPER SHORT CUT PRESET gt Select No PRESET or preset number between 1 100 WASH SHORT CUT PRESET NOT AVAILABLE YET JOYSTICK SPEED Default setting is 60 Use gt w to increase decrease LOGIN gt MAIN MENU gt JOYSTICK gt JOYSTICK SPEED MOVE aw INCREASE DECREASE SPEED SETTING MOVE 4 TO SAVE amp EXIT PAN LIMITS Program Camera to pan only withi
46. tic screens which display useful information for the technician and remote help diagnostics for Redvision s technical support helpdesk They are not configurable To access the diagnostic screens LOGIN gt MAIN MENU gt SETUP gt DIAGNOSTICS MOVE aw TO SELECT SYSTEM STATUS CAMERA TELEMETRY OR MOTORS MOVE 4 TO SAVE amp EXIT To exit motors it is necessary to recall the menu see 6 1 1 7 NIGHT MODE 7 1 7 2 7 3 7 4 7 5 IR MODE Default Night Mode is when the Camera s infra red pods RVX IR models are on and or the Camera is in mono The option exists for the camera to be forced to stay in colour See 8 2 1 Manual IR pods turn on amp Camera switches to mono manually all models Timed IR pods turn on amp Camera switches to mono at programmed times all models Light sensing IR pods turn on amp Camera switches to mono when it gets dark all models LOGIN gt MAIN MENU gt NIGHT MODE gt IR MODE MOVE aw TO SELECT MANUAL TIMED LIGHT SENSING MOVE 4 TO SAVE amp EXIT ON LEVEL Light level at which the IR pods turn on RVX IR models and or the camera switches to mono ALL RVX models Default setting is 55 must be lower than OFF level The lower the number the darker the light needs to be in order for the camera to switch to mono and IR pods turn on LOGIN gt MAIN MENU gt NIGHT MODE gt ON LEVEL MOVE aw CHANGE VALUE MOVE 4 TO SAVE amp EXIT TECH SUPPORT COMMENT
47. tions regarding return of the defective product and no product will be accepted for repair replacement credit or refund without the written authorisation of Redvision or in accordance with Redvision s written instructions In the case of any such return the buyer shall bear the risk of loss or damage and shall prepay all transportation charges to Redvision Repaired or replacement product will be shipped with freight prepaid by Redvision and the buyer shall bear the risk of loss or damage The replaced product shall become Redvision s property In no event shall Redvision be responsible for de installation or reinstallation of the product or for the expenses thereof If it is determined that product is not defective the buyer shall pay Redvision all costs of handling inspection repairs and transportation at Redvision s then prevailing rates Repairs and replacements covered by the above warranty are warranted to be free from defects as set forth above except that the defect must appear Within three 3 months from the date of repair or replacement or Prior to the expiration of the above twenty four 24 month period whichever is later With respect to product not manufactured by Redvision to the extent permitted extends the warranties and affords the remedies to the buyer given to Redvision by its vendor of said products The foregoing warranties do not extend To expendable items To experimental or development products To prod
48. uct which has been subjected to misuse neglect accident or abuse To the unauthorised repair or alteration by anyone other than Redvision To improper installation storage or maintenance by anyone other than Redvision To product used in material violation of Redvision s instruction or To product which has had its serial numbers or month and year of manufacture or shipment removed defaced or altered or To software The term software means a set of logical instructions and table of information which guide the functioning of a processor Such set may be contained in any medium whatsoever including without limitation hardware containing a pattern of bits representing such set provided however the term software does not mean or include the medium Redvision shall charge for the repair of all product returned out of warranty call Redvision Customer Service 44 0 1420 448 448 for an RMA number or visit www redvisioncctv com for more information Due to a policy of continuous product development the content of this manual may change without notice Redvision CCTV Limited will endeavour to ensure the latest version is made available through the download section on its website www redvisioncctv com Copyright 2008 2011 Redvision CCTV Limited All rights reserved Redvision CCTV the Redvision Logo Redvision X series RV Camera Series Redzone IR Illuminator are trademarks or registered trademarks of Redvision CCTV Li

USER MANUAL - CCTV Center

Contents

Download Pdf Manuals

Related Search

Related Contents