Initialization of Cryogenic S600X Magnetometer
Contents
1. Figure 5 Flux transformer SQUID loop and tank circuit Pick up coils form a second order gradiometer 3 Cryogenic S600X magnetometer Cryogenic model S600X is an RF SQUID magnetometer whose superconducting solenoid is able to produce magnetic field of 6 5 T The main components of the system are the cryostat and the electronics rack The rack contains a Lake Shore 340 temperature controller a SCU 500 SQUID electronics unit a data acquisition system DAS a HLG 200 helium level gauge a Windows based computer a SMS 80 power supply for the superconducting magnet a valve block control unit an electronic filter unit and an oven Diagram of the electronics rack is in figure 6 In addition a rotary vane pump is used to draw gaseous helium through the VTI and a pumping system is also needed for removing air from the cryostat s vacuum space Currently the pumping is done with a diffusion pump In this section is a brief description of the components of the system their initial ization problems discovered during testing and their solutions Lake Shore 340 temperature controller CAE gt e Ol SCU 500 SQUID electronics HLG 200 helium level gauge Data Acquisition System DAS Computer O o HHB co SMS 80 magnet power supply O oo0o000000 eae2. is shown in figure 8 I V V J Figure 8 Schematic of four wire temperature measurement The pin configuration of the temperature controller inputs are given in the con troller s manual 8 Information about the filter block s pin configuration was not available The temperature sensors are semiconductor diodes with temperature dependent for ward voltage Therefore the pin configuration can be decided by measuring which of the pins show a voltage difference The measurements were made at room tempera ture using a Fluke 175 multimeter in diode test mode In addition it was assumed that the upper pin pair of the M5P connector of the filter block are the current pins and the lower ones are the voltage pins The results are shown in table 1 The actual voltage readings are not essential but the non zero reading indicates forward biased configuration As can be seen in table 1 pins A and B are J and J and D and E are V and V respectively Thus 10 the pin configuration is as shown in table 2 Table 1 Voltages measured from temperature sensors terminals pin pin Voltage A V Voltage B V A B 0 766 1 189 B A 0 0 D E 0 766 1 189 E D 0 0 Table 2 Pin configuration of connectors DIN 45322 1 M5S Description I V Shield V I No connection gt J cea w HD ory AININ The cable was chosen acc
3. Around the helium reservoir is a metal layer to shield the reservoir from ambient magnetic field A degaussing coil is wound on to the shield and connected to the automatic degaussing electronics The reservoir is cooled by liquid nitrogen and gas cooled radiation shields and insulated by a vacuum to prevent heat leaks Inside the cryostat are the VTI and the superconducting magnet The VTI contains the SQUID sensor sample tube and heat exchanger The heat exchanger is used to control the temperature of the sample Liquid helium from the reservoir is expanded to gas and passed through the heat exchanger The temperature of the gas and the sample can vary from 1 5 K to 320K 7 In the center of the magnet are the superconducting pick up coils which are connected to the input coil of the SQUID and thus form a flux transformer On the bottom of the cryostat is a thermometer and a heater that are used during precooling the cryostat s helium reservoir with liquid nitrogen After the reservoir is cooled to 77K and before filling with helium the heater is switched on to boil away remaining nitrogen that would crystallize at liquid helium temperature On top of the VTI are an airlock for changing the sample and the sample moving system The sample can be moved vertically and rotated by two computer controlled 15 stepper motors A diagram of the cryostat is in figure 9 Sample moving mechanism Air
4. the RF flux The modulated triangle wave is fed in to a lock in amplifier with the sine wave as a reference The operation point of the system is locked to one of the peaks corresponding n or troughs corresponding n o 2 of the triangle wave by a feedback current fed in to the RF coil that cancels any changes in flux from the input coil 5 6 The amplifier s output voltage is proportional to the difference of flux threading the SQUID loop from the operation point corresponding to a peak or trough of the triangle wave The principle is shown in figure 4 Figure 4 Modulation of SQUID output by a 40 kHz sine wave In order to remain in the flux locked mode the maximum flux difference from the operation point is Ad Py 4 If the system does not react to changes of flux fast enough the operation point slips to another peak or trough 6 7 2 5 Flux transformer The input flux to the SQUID is delivered by a flux transformer in which the input coil is connected to a pick up coil When a magnetic sample moves through the pick up coil it induces a current in the leads which in turn sets up a flux in the input coil that couples to the SQUID loop To prevent the static magnetic flux of the superconducting magnet from giving a signal the pick up coils are wound in a second order gradiometer configuration Thus the net current induced by a static flux will be zero 7 The system is shown in figure 5 Ly Vi
5. 000 Ge 9 12 Mitialization a A A 4 Summary References Appendix I 11 12 12 12 13 13 13 14 15 15 15 16 16 18 18 18 20 Symbols and abbreviations Symbols e Elementary charge h Planck s constant h Planck s constant h 27 1 Current de Critical current dre Radio frequency current le Tunnelling current Li Input coil inductance Ls SQUID loop inductance L Tank circuit inductance Mas Mutual inductance of input coil and SQUID loop Mes Mutual inductance of tank circuit and SQUID loop Vae DC voltage V Tank circuit voltage Ad Deviation of flux from operation point Ay Phase difference V Frequency Do Magnetic flux quantum Dos External magnetic flux Abbreviations AC Alternating Current DAS Data Acquisition System DC Direct Current DIP Dual In line Package LED Light Emitting Diode RAM Random Access Memory RF Radio Frequency SERF Spin Exchange Relaxation Free SQUID Superconducting QUantum Interference Device VI Virtual Instrument VTI Variable Temperature Insert 1 Introduction The work of B D Josephson led to the invention of Superconducting QUantum Interference Devices SQUIDs at Ford Research Laboratories in the mid 1960s The first to be invented was the direct current DC SQUID which was soon to be followed by the radio frequency RF SQUID 1 Though the DC SQUID was developed first and still offers the highest sensitivity RF SQUIDs are widely used because of their simpler stru
6. LAPPEENRANTA UNIVERSITY OF TECHNOLOGY FACULTY OF TECHNOLOGY LUT ENERGY DEPARTMENT OF ELECTRICAL ENGINEERING Bachelor s Thesis Initialization of Cryogenic S600X Magnetometer Aki Pulkkinen 26 3 2010 Supervisor prof Erkki Lahderanta Contents 1 Introduction 2 Operation of an RF SQUID magnetometer Jol Josephsom junction a Me Ue A ate A a A a A a i aa 2 2 Flux quantization A eet a ec ok kl Se ee ws Se he a 2 3 Tank circuit and hysteretic behaviour 2 4 Flux locked Operation i 2 66 2 a 2 ase 1 aoe aw ds Od BG Zo Elux transiorrmier le e s Se le 3 Cryogenic S600X magnetometer 3 1 Lake Shore 340 temperature controller g1 itializati N e lt 5 oc a ae he ee hae eS eS 3 2 SCU 500 SQUID electronics 4 isn dite de dde a dios Se ae 3 3 Data acquisition system DAS cotorra 3 4 Cryogenic HLG 200 helium level gauge 3 0 Comp tei DA Bee Rea A hoe ei hea had oleate 3 6 Cryogenic SMS 80C magnet power supply 3 6 1 Initialization ogee hs bY Gis lowe og ee kee amp eee ea 3 7 Valve block control unit ce Oe ae oe as ae a a ea bee Ge 3 8 Electronic filter unit aca da a Sy a ah tk te a og hs ea ed B00 MOWER es Sk Cots bod eek GS Seed ie Sok eh oa Se ae sara rotas aaa es te de a dede dl e dete Me Roe te e BS E Nd te OE the Mua fe ib thee Sven ie Rian ea grb lll Initialization cus Sn ds ee ig A as SRR OR S 3 12 Sample moving mechanism 00
7. Or PY Valve block O a Ne KY Filter block Oven Co LT Figure 6 The electronics rack 3 1 Lake Shore 340 temperature controller The temperature controller monitors the temperatures of two temperature sensors A and B located in the VTI Sensor A measures the temperature of the VTI heat exchanger and sensor B the temperature of the sample tube The controller s heater is used to control the temperature in the sample space Helium flow cools the sample and temperature information is fed back to the temperature controller The controller adjusts the heater s power to keep the temperature at a pre adjusted value The controller is connected to the computer via IEEE 488 bus The voltage data of the temperature sensors is passed to the controller via the filter block 7 The cables connecting the temperature controller to the filter block were missing The connectors of the cables at the controller end are male DIN 45322 and at the filter block end female M5 M5S Figure 7 shows a schematic diagram of these connectors 5O 6 O1 10 Po 2 a Figure 7 a DIN 45322 connector b M5S connector The temperature is measured by a four wire configuration which improves the ac curacy by preventing the resistance of excitation current carrying wires to couple with the resistance of the temperature sensor albeit the excitation current for Si and GaAlAs diode sensors is 107 A 8 A schematic of the four wire configuration
8. Pentium processor 32 MB of RAM 2 2 Gbit hard drive 3 5 disk drive and a CD ROM drive It includes three cards to operate the magnetometer an IEEE card a stepper motor card and an interface card for the DAS unit The operating system is Windows 95 and the software used to control the magne tometer runs in National Instruments LabVIEW version 4 0 1 7 3 6 Cryogenic SMS 80C magnet power supply The Cryogenic SMS 80C magnet power supply is used to power the superconducting magnet This particular model is capable of delivering 80A current at 5V to a purely inductive load like a superconducting coil The power supply has an integrated reversing switch for changing the direction of the current a feature that is needed for hysteresis measurements Remote operation of the magnet power supply is possible by LabVIEW via the IEEE 488 bus The unit can also be controlled manually via eleven push buttons in the front panel 7 3 6 1 Initialization The magnet power supply is also controlled via the IEEE 488 bus so an address on the bus is needed The address can be set via LabVIEW configuration file or via DIP switches located near the IEEE 488 connector on the power supply s back panel There are 6 switches and the 5 switches furthest away from the IEEE 488 connector set the address The sixth switch is unused The states of the switches correspond to a binary number so that the switch furthest away from the connector is the least sig
9. ance frequency and thus the voltage across it Because of the coupling the magnetic flux inside the SQUID loop also changes with the driving frequency of the tank circuit Figure 1 shows a schematic diagram of the arrangement Lik Mes Figure 1 SQUID loop and tank circuit Mt s is the mutual inductance of SQUID loop and tank circuit and Ls is the inductance of the SQUID loop 107 H 4 Applied external flux as a function of total flux is given by p Des Lat sin 2 E 4 Do where L is the inductance and i the critical current of the SQUID loop Total flux as a function of applied flux can be determined from equation 4 If 27L i gt 1 the dependence 9 is multivalued for some range of Pext If Bext is swept at a large enough amplitude hysteretic jumps will occur and cause a dissipation of energy The hysteretic behaviour is shown in figure 2 with L i 1 If the total flux is initially 0 and is swept at an amplitude in the range of Y lt ext lt O the traced hysteresis loop is A gt B gt C gt D gt E gt F gt G gt H gt A as shown in figure 2 The hysteretic loss reduces the RF flux coupled to the SQUID loop during the next RF cycle Thus no hysteresis loops are traced until the tank circuit has gained enough energy which may take several cycles However if the current t t is increased the tank ciruit recovers at a faster rate until a current level is reached where the hysteresis
10. ation 1 ig i sin A 1 where 2 is the critical current of the junction Equation 1 defines the DC Josephson effect in which the tunnelling supercurrent flows without a voltage across the junction which means that the whole system is in the superconducting state If a DC current i gt ie is fed through the junction a DC voltage Va will exist across the junction The tunnelling current now has an oscillatory behaviour the tunnelling current oscillates back and forth through the junction with an amplitude ie The frequency of the current is given by 2e ee 2 V h de The small voltage component with a frequency v can be observed in the voltage across the junction This phenomenon is called the AC Josephson effect 3 2 2 Flux quantization Because of the Meissner effect magnetic flux inside a superconductor is cancelled by screening currents However magnetic flux can exist in a superconducting ring but only if the flux produced by screening currents is such that the total flux inside the ring is quantized The flux threading the ring is an integral multiple of the magnetic flux quantum Sy which is defined by h 08 Do qe 2 0678 10 Wb 3 e 2 3 Tank circuit and hysteretic behaviour In an RF SQUID the superconducting loop couples inductively to the tank circuit which is driven at a constant current at its resonance frequency typically from 20 MHz to 30 MHz The coupling changes the circuit s reson
11. caused the setting of magnetic field to be very slow It is possible to change the current tolerance limits in the configuration file such that the current settles faster The default settings and the ones used during testing are listed in appendix I When SX_MAIN was run for the first time after powering up the system the magnet power supply s display showed an error message REVERSING SWITCH FAULT The message disappeared as PSU do amp display s3 was run The error message did not seem to show up anymore if SX MAIN was run again without powering down the system The exact reason for the problems was not discovered However the problems and error messages disappeared as all the cables connections were checked and the correct settings found 3 7 Valve block control unit The valve block houses the manual and solenoid valves to control the flow of gases in the variable temperature insert It is controlled via the DAS 7 14 3 8 Electronic filter unit The filter unit contains the filtering circuits for all electricity connected to the cryo stat It also houses the power supplies for the auxiliary VTI heater and the SQUID circuit 7 3 9 Oven The oven is an auxiliary heater that extends the magnetometers temperature range from the normal 1 5 320 K up to 700K 7 3 10 Cryostat The cryostat is a container made of aluminium and fiberglass It contains the liquid nitrogen and helium reservoirs
12. cryostat at the end of the sample rod 3 12 1 Initialization The initialization of the sample moving mechanism is possible via the SX_MAIN VI s Stepper find home s button The initialization includes moving the mech anism up and down in between two optical switches that set the limits for the movement The mechanism then finds it s center position with the help of a third optical switch The motion of the sample moving mechanism was not smooth For reliable mea surement results it is important that the movement of the sample is steady The stepper motor control system may also misinterpret the position of the sample if the motor skips some of the steps Probable reasons for this behaviour are analyzed in the following paragraph Friction between the moving surfaces namely the rotor and the axle can cause the mechanism to get stuck Lubrication of the parts made the problem somewhat smaller but did not remove it The fitting of the axle and the motor may have been too tight and thus disturbed the motion Also the resonance effects due to the periodical vibration and the load of the motor can disturb the motion The issue was solved by replacing the motor and the axle with new ones with looser axle fitting 4 Summary After the modifications descripted in this work the magnetometer should operate correctly and be ready for measurements However the system is complex and some issues may still arise during further t
13. cs rack and contains most of the electronics of the SCU 500 such as the system parameter controls and the lock in amplifier that allows the operation of the SQUID in a flux locked mode The control unit also detects the output signal of the SQUID circuit which is fed to the data acquisition system 7 The RF head is located on the cryostat It contains the RF circuitry driving the tank circuit and the thin film SQUID sensor in the cryostat at liquid helium temperature 3 3 Data acquisition system DAS The data acquisition system controls the system s inputs and outputs except the power supply and the temperature controller It also has a push button to activate the degaussing coil 7 3 4 Cryogenic HLG 200 helium level gauge The helium level gauge measures the depth of liquid helium in the cryostat The device consists of a control unit and a sensor The sensor is made of an alloy NbTi whose critical temperature is above the boiling point of liquid helium 4 2K The part of the sensor in helium vapour becomes superconducting and so the voltage across the sensor is directly proportional to the length of sensor in helium vapour A small heater is wound to the end of the sensor to ensure small resistance despite the helium level Under normal operation the meter updates the helium level every 15 minutes and shows the helium level in millimeters on a 3 digit display 7 12 3 5 Computer The computer is equipped with a 166 MHz
14. cture and lower manufacturing costs Strictly speaking the term quantum interference device refers to the working principle of a DC SQUID but the same term is used for its RF counterpart as well Since their invention SQUID devices have been the most sensitive magnetometers allowing the measurement of magnetic flux changes less than the magnetic flux quantum Py However the Spin Exchange Relaxation Free SERF magnetometer developed in the early 2000s has reached competitive sensitivity 2 This work concentrates on the operation of a hysteretic RF SQUID magnetometer and the structure and initialization of the Cryogenic S600X SQUID magnetometer located in the physics laboratory of Lappeenranta University of Technology 2 Operation of an RF SQUID magnetometer RF SQUIDs are based on a ring of superconducting material containing a weak link e g a Josephson junction 2 1 Josephson junction A Josephson junction consists of two superconductors separated by a thin insulating layer If the layer is thin enough Cooper pairs can tunnel through it Electron pair waves have different phases at each side of the junction though the phases are coupled because of tunnelling The tunnelling current has a maximum value when the phase difference Ad 5 A Josephson junction is a special case of a weak link between superconductors in which the dependence of the tunnelling supercurrent is from the phase difference is sinusoidal as in equ
15. esting 18 Some of the system s components are not up to date especially the computer but just replacing parts with new ones can be problematic The computer is quite old and runs Windows 95 and LabVIEW version 4 0 1 Re placing it would not be straightforward because it is possible that the interface cards for IEEE bus stepper motor and DAS are not supported on newer versions of LabVIEW Thus replacing the computer could require other major changes to the system The LabVIEW version 4 programs are not supported by current versions of LabVIEW so a new version of the control software would also be needed The possibility of upgrading the system was not actually investigated because it goes beyond the scope of this work 19 References 1 Silver A H 1979 SQUIDs Past Present and Future IEEE Trans Mag 10 MAG 15 1 Allred J C Lyman R N Kornack T W amp Romalis M V 2002 High Sensitivity Atomic Magnetometer Unaffected by Spin Exchange Relaxation Phys Rev Lett 89 13 Tinkham M 2004 Introduction to Superconductivity Dover New York 2nd edition ISBN 0 486 43503 2 Webb W W 1972 Superconducting Quantum Magnetometers JEEE Trans Mag MAG 8 1 Giffard R P Webb R A amp Wheatley J C 1972 Principles and Methods of Low Frequency Electric and Magnetic Measurements Using an rf Biased Point Contact Superconducting Device J Low Temp Physics 6 5 6 Cryo
16. et power supply respectively These VIs must be run by clicking an arrow icon on the upper left corner of the VI It is recommended to run these in the following order 1 SX_MAIN 2 LTC do amp display 3 PSU do amp display s3 4 600 error log When SX_MAIN is run the program asks for a configuration file which contains values for various parameters of the system The configuration file has extension ini If the initialization is successful LTC do amp display and PSU do amp display s3 should show the text initialization looks ok on the yellow background on the bottom of the VI window 10 A functioning configuration file was not found in the system so it was consid ered best to modify an existing file The file chosen to be modified was named Pernor340 ini because the name was thought to refer to the present temperature controller Lake Shore 340 Temperature Controller The original temperature con troller of the system Conductus LTC 10 had been replaced The original file was preserved and modifications were made only to the copy of the file named Copy of Pernor340 ini If any parameters need to be modified it is recommended to make a new initialization file rather than overwrite the existing one 17 3 12 Sample moving mechanism The sample moving mechanism has two stepper motors one for vertical and the other for rotational movement of the sample The motors are on top of the
17. genic Limited SCU 500 Manual Cryogenic Limited S600 Hardware Manual Lake Shore Cryotronics Inc 2004 Lake Shore Model 340 User s Manual Cryogenic Limited SMS Series Superconducting Magnet Controllers User s Manual Cryogenic Limited 1997 S600X SQUID Susceptometers Software Manual 20 Appendix I The initialization settings of magnet power supply Table 3 Initialization settings of magnet power supply 10 Parameter Typical setting Tested setting PS id SMS 80 4 20 SMS 80 4 20 GPIB PS 4 4 Delay ms 0 0 Norm rate A s 0 1 0 5 0 100 Fast rate A s 0 5 0 500 Start degauss T 3 3 0000 End degauss T 0 002 0 008 0 0020 T A 0 0840 0 0840 Overshoot 0 02 0 0200 Bmax T 6 5 6 5000 Vim 4 5 4 50 Heater 4 4 00 PS out bipolar bipolar Heater B Off Heater off after s 45 45 00 Max d V dt 5 04 1074 5 0 107 B stab test t s 30 30 00 Tolerance A 0 01 0 100
18. lock gt E 1 Nitrogen reservoir E Variable temperature insert Sample tube lt Helium reservoir Heat exchanger IL a GFA ermometer SQUID sensor housing gt t4 Thermometer B He Pick up coils Superconducting magnet Figure 9 Diagram of the cryostat 3 11 Software The system operating software runs under National Instruments LabVIEW version 4 0 1 The LabVIEW environment consists of virtual instruments VIs which are subprograms controlling different parts of the system 10 3 11 1 Initialization To get the system fully initialized the following are required The temperature controller and the magnet power supply must be connected to the IEEE 488 bus and switched on The data acquisition card and the stepper motor card must be installed in the computer 16 The sample insertion power supply must be on and the insertion unit must be connected 10 When the main program is executed LabVIEW will load a number of VIs four of which remain visible on the screen These are SX_MAIN LTC do amp display PSU do amp display s3 and S600 error log SX_MAIN is the master VI and has the system main menu LTC do amp display and PSU do amp display s3 show information from the temperature controller and the magn
19. loop is traced at every RF cycle This leads to plateaus in the dependence of the tank circuit voltage V from the current 7 driving the tank circuit The plateau begins as the current reaches the value at which hysteretic behaviour begins and ends as the hysteresis loop is traced during every RF cycle Typically the operating point of the RF SQUID is set at the center of a plateau 5 6 Figure 2 Total flux as a function of applied flux If 6 2 a smaller flux amplitude is sufficient to cause hysteretic behaviour The hysteresis loop is also smaller A gt B gt C gt D gt A Thus a plateau in the V irf curve will appear at a smaller current value V ipt curves with different values lie between the solid and dashed curves in figure 3 If the current is further increased the system will eventually trace larger hysteresis loops with more jumps V V 1 2 S o a b Figure 3 a Tank circuit voltage as a function of the driving current The solid and dashed lines represent the cases of 0 and o 2 respectively b SQUID output at current i4 V 2 4 Flux locked operation The output voltage V of the tank circuit is a triangle wave with a period of Do Normally the SQUID is operated in flux locked mode in which the triangle wave is modulated with a low frequency signal The Cryogenic S600X s SQUID electronics unit the SCU 500 uses a 40kHz sine wave that produces a 9 2 peak to peak modulation to
20. nificant bit The switches are numbered such that switch number 6 corresponds to the least significant bit and the switch number 1 is unused Switch on and off correspond to binary 1 and 0 respectively The default setting is 001002 i e 41o 9 The address must be different from the one specified for the temperature controller 13 If the address set via the switches does not match the one in the configuration file it is advisable to use LabVIEW to change the address due to the possibility of breaking the mechanical switches With proper address setting the system should automatically select remote control mode This is indicated by a LED in the REMOTE button in the front panel The original configuration file contained different parameter values than was spec ified in the power supply s manual The parameter values in the file Copy of Per nor340 ini were changed to correspond the values given in the manual Some problems occurred during initialization at an early stage of testing If the parameter PS out in the configuration file was set to bipolar as recommmended in the manual the magnet power supply failed to initialize However if PS out was set to unipolar the initialization was successful Apparently this also disabled the power supply s ability to change current direction which is needed for hysteresis measurements Later there were problems with current settling which
21. ording to the specifications given in the temperature con troller s manual The cable has two twisted pairs and a braided shield Each wire has a cross section area of 0 25 mm 3 1 1 Initialization In order to control the temperature controller via IEEE 488 bus IEEE Terminator End Or Identify EOI and Address parameters must be set This can be done using the controller s front panel By pressing the Interface key one gets access to the COMPUTER INTERFACE screen The options for the IEEE Terminator are CR LF LF CR CR LF or none for EOI On or Off and for address from 1 to 32 A and y keys are used to make the selections Pressing the Next Setting key advances to the next parameter Selections are saved by pressing Save Screen or cancelled by pressing Cancel Screen The default settings for these parameters are IEEE Terminator CR LF EOI On and address 12 The address specified here must be the same than the one specified in the system configuration file 8 11 At first during testing the software could not switch on the temperature controller s heater and controlling the temperature of the sample was impossible The cause was a bug in the software typical for the early versions of the S600X magnetometer The bug has now been fixed 3 2 SCU 500 SQUID electronics The main components of the SCU 500 system are the SCU 500 control unit RF head and a SQUID sensor assembly 6 The control unit is located in the electroni
Download Pdf Manuals
Related Search