Evaluation Kits Start guide
Contents
1. a JP No Feature Setting for control TCXO 11 2 Fixed to GND 2 3 Fixed to power supply 1 2Short Always needs to be used in 1 2 Short setting RESETN setting Short Fixed to VDD Open N C Shot J Always needs to be used set in Short Use VDD_USB1 power supply Short Use Open Not use Open J When using power supply for VDD_USB IC2 regulator set JP13 Use VDD_USB2 power supply Short Use Open Not use Shot i I one of the USB power supply used l Set this setting only when USB3 connector power supply is Short Use Open Not use Open 1 used I 1 JP19 Short Connection Open OQ resistor connection stot Short when R45 is implemented I JES pout Hse Opon NOUSE Open a When using 3 3V power supply for USB UART conversion JP14 iShort Use Open Not use Open E peee PETIN LSI set one of the USB power supply to use cal Ma iShort Use Open Not use Open E JP16 VDD_PER setting iShort Use Open OQ resistor connection Open fs Short when R42 is implemented JP20 Short Connection Open 00 resistor connection Open Short when R46 is implemented D Weta s reotes 4 0 2M JP10 SPI MISO pin selection Short GPIOA2 selected Open GPIOA2 not selected open Short I JP11 SPI MOSI pin selection IShort GPIOA3 selected Open GPIOA3 not selected open Short i JP12 SPI SCK pin selection Short GPIOAO selected Open GPIOAO not selected open P Short I JP15 SPI SSN pi2. ay Fd Resize J OCH Figure 5 Screen after RREG 6C Command This concludes the preparation for using this product From now on refer to the attached Wireless PAN Test Tool User s Manual and perform communication tests to check the device connection state and proper operations FEXL7416_EVA_startguide 01 7 LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide Revision History Document No Issue Date Description Previous Edition New Edition FEXL7416_EVA_startguide 01 8
3. information is error free and LAPIS Semiconductor shall have no responsibility for any damages arising from any inaccuracy or misprint of such information Please use the Products in accordance with any applicable environmental laws and regulations such as the RoHS Directive For more details including RoHS compatibility please contact a ROHM sales office LAPIS Semiconductor shall have no responsibility for any damages or losses resulting non compliance with any applicable laws or regulations When providing our Products and technologies contained in this document to other countries you must abide by the procedures and provisions stipulated in all applicable export laws and regulations including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act This document in part or in whole may not be reprinted or reproduced without prior consent of LAPIS Semiconductor Copyright 2015 LAPIS Semiconductor Co Ltd LAPIS Semiconductor Co Ltd 2 4 8 Shinyokohama Kouhoku ku Yokohama 222 8575 Japan http www lapis semi com en FEXL7416_EVA_startguide 01 1 LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide Introduction Thank you for your purchasing our product Read this Start Guide first before using the product to ensure proper use of the product After reading keep this guide handy for future reference This start guide describes the attached articles and connection
4. methods The following related manuals are available and should be referenced as needed E ML 7416 Data Sheet E ML 7416LSI Design Manual E Wireless PAN Test Tool User s Manual FEXL7416_EVA_startguide 01 u ML7416LSI Evaluation Kit LAPIS Semiconductor Co Ltd Start Guide Contents WTOC UC O nET T E EAEE AEAEE li 1 Cautions inHandling TAIS ProdUCt cis aicsccaceicadanius Saaaatettoceadandetoedsabodoadeh maandetsosnadensuianieseadeains r EE ERORE 1 PE LID Te LOW aan O EO EE EE E E E E 2 STEP1 Checking on Package Contents 000 0 ccccccssssssscccceeeccccceceeesessessssneeeeeesscceceeeeseeessssssaeeeeeeeeceeeeseeeeeseeetssaaeeees 2 SIEP2 Setting Evaluation Board sassinoro aar NE E ENEAN OAA 3 STEP3 Setting up Serial Communication Software essssseeessesseerreessssssssssesrerrrerresssssssssserrerrrerereesssssssssererrereeeeesssssssene 5 IRE VISION TROL ogoro N n E OE E E E NO 8 FEXL7416_EVA_startguide 01 il LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide 1 Cautions in Handling This Product e This product is an evaluation kit It shall be used only for evaluations e Use the application software of this product on a personal computer with Windows XP or Windows 7 installed e Duplicating all or any part of the software of this product or distributing a copy without the permission of the copyright owner violates the copyright e LAPIS assumes no responsibility for retrofitting and illegal using of this pro
5. 16_EVA_startguide 01 4 LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide STEP3 Setting up Serial Communication Software This step describes how to set up serial communication software used for operating the evaluation kit LAPIS recommends Tera Term free software as the serial communication software Macros included in the packaged CD_ROM are written in the macro language for Tera Term Download it before starting this operation 1 Install Tera Term on the personal computer used for the evaluation 2 Install the Virtual COM Port driver for USB UART conversion FTDI device on the personal computer used for the evaluation Download the driver from the following Web page http www ftdichip com FT Drivers htm 3 Connect the evaluation board and the microcomputer board 4 Use the USB cable to connect the ML7416 evaluation board with the personal computer on which Tera Term is installed 5 Start Tera Term When it has started the screen in Figure 3 is displayed File Edit Setup Control mr Help Tera Term New connection TCPIP Hast Telnet TEF port Fort COM Cancel Help Figure 3 Tera Term Initial Screen 6 Select Serial then in the Port combo box select a COM port to use 7 When it has started from the Setup menu select Serial port change the settings by referring to Figure 4 then click the OK button Setting value Baud Rate 57600 Data 8 bit Parity
6. ROHM GROUP FEXL 416 EVA_startguide 0 LAPIS SEMICONDUCTOR ML7416LSI Evaluation Kit Start Guide Read this guide first Issue Date May 7 2015 LAPIS Semiconductor Co Ltd Rca A Start Guide Notes 1 2 3 4 5 6 7 8 9 10 11 12 13 The information contained herein is subject to change without notice Although LAPIS Semiconductor is continuously working to improve product reliability and quality semiconductors can break down and malfunction due to various factors Therefore in order to prevent personal injury or fire arising from failure please take safety measures such as complying with the derating characteristics implementing redundant and fire prevention designs and utilizing backups and fail safe procedures LAPIS Semiconductor shall have no responsibility for any damages arising out of the use of our Products beyond the rating specified by LAPIS Semiconductor Examples of application circuits circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products The peripheral conditions must be taken into account when designing circuits for mass production The technical information specified herein is intended only to show the typical functions of the Products and examples of application circuits for the Products No license expressly or implied is granted hereby under any intellectual property rights or ot
7. duct e Should this product cause a harmful radio wave interference immediately change the frequency used or stop the radio wave output and make crosstalk avoidance treatments e The evaluation board is set with constants of 200 kbps or lower data rate and 920 MHz band at shipment If you want to use other conditions for evaluation refer to the Design Manual to modify the constants FEXL7416_EVA_startguide 01 1 LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide 2 Setup Flow This flow is from the check on package contents to the assembly STEP 1 Checking on Package Contents STEP 2 Setting Evaluation Board STEP 3 Setting up Serial Communication Software STEP1 Checking on Package Contents Open the box First confirm all of the following articles are available Should there is any missing or broken part contact the source from which you purchased it CD ROM is packaged only when purchased first time The mounted parts may look different from the photo depending on the shipment time Prepare the stabilized power supply and the serial communication software TeraTerm by yourself O ML7416 evaluation board 1 O Antenna 1 O CD ROM 1 O MicroUSB cable 1 Only for the first purchase Pham q M 16 EVB Tool CD FEXL7416_EVA_startguide 01 2 LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide STEP2 Setting Evaluation Board This chapter describes the evaluation board set
8. her rights of LAPIS Semiconductor or any third party with respect to the information contained in this document therefore LAPIS Semiconductor shall have no responsibility whatsoever for any dispute concerning such rights owned by third parties arising out of the use of such technical information The Products are intended for use in general electronic equipment 1 e AV OA devices communication consumer systems gaming entertainment sets as well as the applications indicated in this document The Products specified in this document are not designed to be radiation tolerant For use of our Products in applications requiring a high degree of reliability as exemplified below please contact and consult with a LAPIS Semiconductor representative transportation equipment i e cars ships trains primary communication equipment traffic lights fire crime prevention safety equipment medical systems servers solar cells and power transmission systems Do not use our Products in applications requiring extremely high reliability such as aerospace equipment nuclear power control systems and submarine repeaters LAPIS Semiconductor shall have no responsibility for any damages or injury arising from non compliance with the recommended usage conditions and specifications contained herein LAPIS Semiconductor has used reasonable care to ensure the accuracy of the information contained in this document However LAPIS Semiconductor does not warrant that such
9. n selection Short GPIOA1 selected Open GPIOA1 not selected open Short JP22 SPI MISO pin selection IShort GPIOA10 selected Open GPIOA10 not Oped Short OoOo ttsti isCCtlected I JP23 SPI MOSI pin selection poet GPIOA11 selected Open GPIOA11 not Open Short selected i JP24 SPI SCK pin selection iShort GPIOA8 selected Open GPIOA8 not selected oen P Short I JP25 SPI SSN pin selection Short GPIOA9 selected Open GPIOA9 not selected open P Short i JP21 ANa COMER Or RISS ROWEL 1Short Supply Open Not supply Open supply l I I He SPI SSIS power Short Supply Open Not supply ome 149 T3 Conecte on Torir scLk 2 GPIOA9 selected 2 3 GPIOAO selected Open Open Not selected Connection selection for DOUT 11 2 GPIOA11 selected 2 3 GPIOA2 selected Open Open I Open for U7 Not selected Connection selection for DIN for 11 2 GPIOA10 selected 2 3 GPIOA3 selected Open l Open U7 INot selected 11 2 GPIOA8 selected 2 3 GPIOA1 selected Open Not selected Open I JP33 Power supply for U7 IShort Supply Open R63 resistor connection When using CN8 connector When using CN10 connector e an JP29 JP31 Always needs to be used set in OPEN JP32 Always needs to be used set in OPEN JP34 Always needs to be used set in OPEN JP35 Connection selection for U7 Always needs to be used set in OPEN Always needs to be used set in OPEN I JP41 MODE_SW power suppl
10. none Stop 1 bit Flow Control hardware FEXL7416_EVA_startguide 01 5 LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide 8 From the Setup menu select Terminal change the settings by referring to Figure 4 then click the OK button Setting value New line Receive CR LF Transmit CR Local echo Uncheck w Tera Term Y T File Edit Setup Control Window Help Terminal 9 window Font Keyboard eral port gt TERRA General nave Setup Restore setup Load key map Tera Term Serial port setup Tera Term Terminal setup Part i Terminal size Mew line Baud rate 57600 80 A 24 Receive CR LF l M Term size win size Transmit CR Cancel Data i bit Cancel 2 a y M Auto window resize Parity none sen bt W Help Terminal ID VTi00 E pa Libs Flow control hardware Answerback M Auto switch VT lt gt TER Kanji receive Kanji transmit Transmit delay SUIS SUIS E msec char 0 mseciline m m OK Help Serial Port Setup screen Terminal Setup screen Figure 4 Tera Term Communication Settings FEXL7416_EVA_startguide 01 6 LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide 9 Press the SW1 reset button on the evaluation board 10 From the serial communication software enter RREG 6C It is successful when OK 88 is displayed as shown in Figure 5 Ml COM 115200baud Tera Term VT PrE EE mE bOI
11. ting Always turn off the power when configuring the board setting Insert the USB cable into the USB connector on the evaluation board enclosed by a heavy line in the photo below An attempt to diagonally insert the USB cable may break the connector SW 1 reset button The USB connectors enclosed by a dotted red circle can also be used for connection provided that the firmware settings are changed USB connector ML7416 Evaluation Board Figure 1 Connection between the Evaluation Board and USB Cable FEXL7416_EVA_startguide 01 3 LAPIS Semiconductor Co Ltd ML7416LSI Evaluation Kit Start Guide This section describes the control board setting The following table lists the jumper functions and recommended settings of the evaluation board Table 1 Table of ML7416BGA Evaluation Board Settings Recomm HW HW HW ended mode mode mode Remarks settings primary _ secondar _tertiar VDDIO_CPU VDD_REG_CPU Short Power supply shared Open Power supply JP1 a iy l Short power supply setting separated I JP2 Loop Filetr voltage monitoring Short Monitor output Open Normal setting open PP ay he TNP METE Aways needs tbe useal open I i JP3 a power supply 11 2 Use VDDIO_CPURF 2 3 Use external powers 1 2 Short SS i he Always needs to be used in 1 2 Short setting I JP4 A_MON pin settings Short Fixed to GND Open A_MON monitor output shot When use as a analog monitor circuit set in Open Po p E as
12. y Short Supply Open Not supply I Connection between MODE _SW i i JP40 and GPIOA12 Short Connection Open R76 resistor connection JP47 12C power supply Short Supply Open Not supply Open JP50 I2C_SCL pin selection 11 2 GPIOA4 2 3 GPIOAO Open et the GPIO pin used as SCL pin JP52 I2C_SCL pin selection 11 2 GPIOA8 2 3 GPIOAO GPIOA4 et the GPIO pin used as SCL pin JP54 i i 11 2 GPIOAS 2 3 GPIOA1 et the GPIO pin used as SDA pin JP55 i i 11 2 GPIOAQ 2 3 GPIOA1 GPIOA5 et the GPIO pin used as SDA pin Power supply for Tester IF 1Short VDD_PER Open Not supply Open lways needs to be used set in OPEN J LINK Short ULINK2 Open Short when R90 is implemented ICE power supply Short Supply Open Not supply sron ICE SWD connection setting short SWD connected Open Not connected ICE SWCK connection setting iShort SWCK connected Open Not connected ii ICE RESETN connection setting Short RESETN connected Open VDD_ICE Recomm SW No Feature ended Remarks settings SW3_1 I2C device WP ION Enable OFF Disable SW3_2 I2C device A2 1 OFF SW3_3 I2C device A1 gt 1 OFF Set the address of I2C device SW3_4 I2C device AO iON 1 OFF 1ON 1 OFF Normally use set in OFF 1 OFF Normally use set in OFF Zz 41 OFF Normally use set in OFF 1 OFF SW2 6 1 OFF Normally use set in OFF 1 OFF Normally use set in OFF FEXL74
Download Pdf Manuals
Related Search