560-5715-x-DRX Series Manual
Contents
1. Input Impedance Over voltage Rating Voltage Contact Ratings Digital Output Channel Dry contact NO Type Power Consumption 120mA max 19 560 5715 X DRX User s Manual Section 10 10 1 10 2 Factory Assistance Telephone Assistance If you have questions about your AMETEK Drexelbrook equipment Contact your local Drexelbrook representative Call the Drexelbrook Service department toll free at 1 800 527 6297 US and Canada or 215 674 1234 Outside North America Fax the following information to the Service department at 215 443 5117 To expedite assistance please provide the following information Instrument Model Number Original Purchase order number Material being measured Temperature Pressure Agitation Brief description of the problem Checkout procedures that have failed Field Service Trained field service personnel are available on a time plus expense basis to assist in start ups diagnosing difficult application or equipment problems or in plant training of personnel Preventive Maintenance and Calibration Certification service contracts are also available to maintain plant efficiency Contact the Service department for further information 20 10 3 Input Output Equipment Return In order to provide the best service any equipment being returned for repair or credit must be pre approved and have a return number issued2. link relay 250VAC 2 A z gt F z 5 z 2 ct E D 5 O SS lt e ar 16 Input Output 9 1 5605715 X DRX Specifications Continued Environmental Humidity 20 to 90 non condensing Temperature Operating 40 to 158 F 40 to 70 C Size 4 5 x3 9 x0 9 114 mm x 99 mm x 23 mm 5 30z 150g 17 560 5715 X DRX User s Manual 9 2 O Modules Specifications Digital Input Module Low Volt 28 67 14 4 DRX Channels aput Voltage Range Input Impedance Channel Isolation Opti Yes Protection Over voltage Rating Power Consumption Channels Output Terminals Contact Ratings Channel Isolation Power Consumption 4 20mA Analog Input Module 4 ch 28 67 11 5 DRX Channels Four 16 bit Input Impedance lt 170 ohms with transceivers Protection Compatibility Over voltage Rating Power Consumption 4 20mA Analog Output Module 4 ch ISOL 28 67 12 8 DRX Channels Four ili 0 kel a lt D ei un bd CO a D H E lt Repeatability Channel Isolation 18 Input Output 9 2 O Modules Specifications Continued Input Output Module p n 28 67 32 2 DRX Channels One 1 analog input One 1 analog output Two 2 digital inputs Two 2 digital outputs Channel Isolation All except for analog input channel Protection Impedance Repeatability Resolution Analog Channel Accuracy Compatibility Over voltage Rating
3. 5605715 X DRX RSSI Received Signal Strength Indicator is measured using a DC Voltmeter between the test point and power supply ground The test point is accessed by inserting a positive meter probe into the RSSI hole on the face of the 5605715 X DRX and the negative meter probe to the Ground terminal The RSSI graph below may be used to test the Receive Signal Strength of the 5605715 X DRX The ideal voltage that should be read from the RSSI test point is 2 5VDC or more This represents a 90 dB signal loss and typically indicates that the radio has 20 dB fade margin left until loss of link It is recommended that the radios be set up with no less than 20 dB margin RSSI vs DC Voltage 30 3 0 DC Volts H N E D e 115 110 105 100 95 90 85 80 RO Signal Strength dBm 13 560 5715 X DRX User s Manual Section 7 Typical Components for a Remote Site 5605715 X a HH Antenna amp Mounting Hardware RAD ISM 900 BD BUS Cable LMR400 Grounding Cable amp Rod Pole used with Pigtail NEMA 4X Enclosure Non Adapter S onductiv CH Single Grounding Point Structures T H mast CO Surge Arrestor GE a Typen N Hm die 14 Input Output Section 8 Ordering Information 5605715 X DRX Part Description RAD ISM 900 SET XD BUS master and slave transceiver 56 05 715
4. In 2 ia Digital Input 1 4 20mA In 8 Digital Input 1 560 5715 X DRX User s Manual 2 5 Passive Input and Output Expansion Modules 2 5 1 2867115 X DRX Passive Analog Input 1 y Current H Source l 4 20mA Device vo KE Ss BEER Floating 1 aaga Current 3 wire te Source 4 20mA Device Signal Floating Configurable Module Address See next page for details External Voltage 4 wire Source 4 20mA Device Gees N H U i U I V H A d KE EN CR Floating Analog input channel 4 connection not shown Input Output 2 5 2 2867128 DRX Passive Analog Output By releasing the top part of the housing the user may access DIP switches that allow selection between FAULT OFF or MAINTAIN LAST STATE for each of the four 4 analog outputs of the 2867128 DRX 8 Loop power supplied by 2 wire radio 4 20mA Device Analog Output 4 20mA C Te age 4 wire 4 20mA Device K q gt Loop power supplied by external device Analog Output 4 20mA DIP Switch Settings MAINTAIN FAULT OFF LAST STATE bel 2 Analog Output channels 3 and 4 connections not shown 560 5715 X DRX User s Manual 2 5 3 5 36VAC DC 5 36VAC DC 5 36VAC DC Power Supply 5 36VAC DC 2867144 DRX Passive Digital Input PER TERR g 7 8 18 A 28 1A IN1 IN2 Digital Liquid Level Fault Contact Ti Pressure Fault Contact Temperatur
5. ana seed Eege eege 19 Section 10 Factory Assistance eisen deeg ege 20 fN WR ET le 20 10 2 REISE er ne en en see ee 20 EC WE eene E EE 21 Section 1 Section 1 gt gt Introduction Introduction Modular DIN rail mount transceiver and I O No programming required Maximum thirty three 33 analog or sixty six 66 digital signals in one direction Class I Div 2 approved Dry contact RF LINK diagnostics output Up to eight 8 expandable I O modules passive active inputs and outputs per master transceiver or eight 8 slave transceivers on common power and communications bus with multiple combinations The Drexelbrook 5605715 X DRX is an integrated radio and I O module designed for bidirectional interfacing of a 4 20mA current loop and two discrete signals in harsh industrial environments This unique design also allows the user the flexibility to add on multiple channels of I O to the transceivers in combinations The Frequency Hopping Spread Spectrum FHSS utilizes the 902 928 MHz ISM band to guarantee a license free interference free link between remote devices and the control room The design is ideal for moving numerous signals within high interference environments without costly cable and conduit runs WARNING EXPLOSION HAZARD Do not disconnect equipment unless power has been switched off or the area is known to be non hazardous FCC Rules and Compliance This device complies with Part 15 of the FCC Rules
6. 1 8 DRX indicate number of slaves 1 8 on part number when ordering RAD IN 4A I 4 channel analog input module 28 67115 DRX RAD OUT 4A I 4 channel isolated analog output module 28 67 12 8 DRX RAD IN 8D 8 channel digital input module 28 67144 DRX RAD OUT 8D REL 8 channel digital output with relays 28 67 15 7 DRX RAD IN OUT 2D 1A I 2 digital 1 analog input output 28 67 32 2 DRX module RAD ISM 900 ANT 4 4 way splitter to cascade receivers in 28 67 05 0 DRX simplex mode Accessories Part Description Antennas RAD ISM 900 ANT OMNI 0 6 4 wave Omni 28 67 16 0 DRX antenna with 6 feet of cable amp MCX M connector RAD ISM 900 ANT OMNI 5 5 dB Omni base 2867 19 9 DRX station Larsen FB35 T900 full ground plain with type N F connector RAD ISM 900 ANT YAGI 6 6 dB Yagi Larsen 3 28 67 20 9 DRX element with type N F connector Cables RAD CAB RG213 50 RG2130 50 feet with typeN 28 67 22 5 DRX M connectors cable loss 7 6 dB 100 feet RAD CAB LMR400 100 LMR400 100 feet with 28 67 23 8 DRX EZ400 NMH type N M connectors cable loss 3 9 db 100 feet RAD CAB RG58 10 RG58 10 feet with type N M connectors cable loss 16 dB 100 feet Adapters 28 67 24 1 DRX RAD CON MCX N SS MCX M to N M fitting with 48 of RG316 cable RAD CON MCX BNC SB MCX M to BNC F with 24 of RG174AU cable RAD CON SMA N SS SMA M to N M with 48 of RG316 cable
7. K International 1 215 674 1234 An ISO 9001 Certified Company Fax 1 215 674 2731 E mail drexelbrook info ametek com Website www drexelbrook com Table of Contents Table of Contents Section TEINMOADETON 2 een ee nanne nanne nnnm nnmnnn nnna 1 S ction ECHO 2 2 1 Analog and Digital Inputs EE 2 2 2 Analog and Re Ee ir nase nee u 4 2 3 RF Link and Choosing Output States use ee ae 5 2 4 5605715 X DRX Block Diagram EE 5 2 5 Passive Input and Output Expansion Modules ccccceeeceeeeeeeeeneeeeeeeeeeeeeseseaeeeeeneeeees 6 2 6 Digital Analog Input Output 2867322 DRX EE 10 Section 3 Configuring HO Module Addresses ssssseeeceeeeeeeeeeeeeeeneeeeeeeeseneeeaeeeeeeeensaneeeeneeeeeeess 11 Section 4 Power Budget Requirements 5605715 X DRX sssseeeeeeeeeeeeseseeneeeeeeeeenseneeeeeeeeeeeess 12 Section 5 Status LEDs 5605715 X DRX s nnnsnsnnsnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnan nnmnnn 13 Section 6 RSSI Troubleshooting 5605715 X DRX nuunsennnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 13 Section 7 Typical Components for a Remote Site 5605715 X DRX sussu000000000n0nnnnnnnnnn 14 Section 8 Ordering Information 5605715 X DRX ssssaaassssssnsnnnnnnrrnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnmnnn 15 Section EES eege 16 9 1 5605715 X DRX Ee TEE 16 9 1 56057 15 X DRX Specifications Continued ue 17 9 2 ee nennen een 18 9 2 VO Modules Specifications Continued
8. OL AMETEK OUT 1A 1B 2A 2B 2 1 3 5605715 X DRX Four Wire Device 4 20mA Current Loop External Voltage 4 wire Source 4 20mA Device en Ss H i l U I NL gt Floating 7 OUT IN 4 20mA Loop RAD ISM AMETEK DREXELBROOK_ our OUT 2 BR 560 5715 X DRX User s Manual 2 2 Analog and Digital Output 2 2 1 5605715 X DRX Output Examples In or 2 5 D Link Status Indicator O Analog Output E fim oO 4 20mA 2 x w ks 5 Supressor Power Supply 250VAC 2A max Digital Output 2 No connection shown Digital Output 1 2 3 2 4 Input Output RF Link and Choosing Output States RF Link Output The Link Status contact on the 5605715 X DRX is Normally Open NO and closes when the radio establishes an RF Link It can be used to switch either a STATUS light or a FAULT indicator Selecting State of Outputs Upon Loss of RF Link The default state upon loss of RF signal for the analog and digital outputs is MAINTAIN LAST STATE They may be wired in series with the RF Link contact to provide a FAULT OFF when RF Link is terminated 5605715 X DRX Transceiver RF Link 5605715 X DRX Block Diagram RF Link A mn D Digital Output 2 RF Link B z Digital Output 2 Ground ER S Digital Output 1 9 to 30VDC Power Digital Output 1 4 20mA Out S Digital Input 2 4 20mA Out gt Digital Input 2 4 20mA
9. ON WAIVER BY SELLER Waiver by Seller of a breach of any of these terms and conditions shall not be construed as a waiver of any other breach SEVERABILITY AND ENTIRE AGREEMENT If any provision of these terms and conditions is unenforceable the remaining terms shall nonetheless continue in full force and effect This writing together with any other terms and conditions Seller specifically agrees to in writing constitutes the entire terms and conditions of sale between Buyer and Seller and supercedes any and all prior discussions and negotiations on its subject matter AMETEK DREXELBROOK An ISO 9001 Certified Company 205 Keith Valley Road Horsham PA 19044 U S and Canada 1 800 553 9092 24 Hour Service 1 800 527 6297 International 1 215 674 1234 Fax 1 215 674 2731 E mail drexelbrook info ametek com Website www drexelbrook com
10. Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by Drexelbrook will void the user s authority to operate the equipment This product is intended for fixed installation applications In order to comply with FCC ISC adopted RF exposure requirements installation of this transmitter system s antenna must be performed in a manner that will provide at least a six foot 2 m clearance from the front radiating aperture to any user or member of the public FCC Part 15 247 ISC RSS 210 UL Class I Div 2 Groups A B C D 560 5715 X DRX User s Manual Section 2 Input Output 2 1 Analog and Digital Inputs 2 1 1 5605715 X DRX Two Wire Device 4 20mA Current Loop Current wire Source 4 20mA Device H 1 d 5le l7 s8 i A B we Le eee e e e em RFLink Power Floating I T FT OUT IN 4 20mA Loop RAD ISM DREXELBROOK UOU Z AMETEK 1A 1B 2A 2B our OUT2 Re Digital Input 1 Digital Input 2 Input Output 2 1 2 5605715 X DRX Three Wire Device 4 20mA Current Loop Current 3 wire Source 4 20mA Device em en A B EZ KS WEE signal E I RFLink Power Positive z Floating T TrT OUT IN 4 20mA Loop RAD ISM R RSSI DREXELBROOK T
11. PROPOSED BY BUYER IN ANY DOCUMENT WHICH SHALL NOT BE BINDING UPON SELLER No salesman or other party is authorized to bind the AMETEK DREXELBROOK Division of AMETEK Inc hereinafter Seller by any agreement warranty statement promise or understanding not herein expressed and no modifications shall be binding on Seller unless the same are in writing and signed by an executive officer of Seller or his or her duly authorized representative Verbal orders shall not be executed until written notification has been received and acknowledged by Seller QUOTATIONS Written quotations are valid for thirty 30 days unless otherwise stated Verbal quotations expire the same day they are made PRICES All prices and terms are subject to change without notice Buyer requested changes to its order Orders including those affecting the identity scope and delivery of the goods or services must be documented in writing and are subject to Seller s prior approval and adjustments in price schedule and other affected terms and conditions Orders requiring certified test data in excess of commercial requirements are subject to a special charge ORDER ACCEPTANCE All Orders are subject to final approval and acceptance by Seller at its office located at 205 Keith Valley Road Horsham Pennsylvania 19044 TERMS OF PAYMENT Seller s standard terms of payment for Buyers who qualify for credit are net thirty 30 days from date of invoice All invoic
12. R A Leader in AMETEK DREXELBROOK Level Measurement For Assistance Call 1 800 527 6297 ide North America 215 674 1234 Installation and Operating Instructions Wireless Interface 560 5715 X DRX Two way multipoint to point Monitoring and Control with Expandable I O Options U S and Canada 1 800 553 9092 24 Hour Service 1 800 527 6297 International 1 215 674 1234 Fax 1 215 674 2731 E mail drexelbrook service ametek com Website www drexelbrook com AME TER Drexelbrook makes no warranty of any kind with regard to the material contained in this manual including but not limited to implied warranties or fitness for a particular purpose Drexelbrook shall not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of material Copyright 2007 AMETEK Drexelbrook EDO 01 07 108 56057 15 X DRX LM Issue 2 Wireless Interface 560 5715 X DRX Two way multipoint to point Monitoring and Control with Expandable I O Options DIII II GER These devices must be wired in accordance with Class I Div 2 wiring methods as described in the National Electrical Code Article 501 4 b or the authority having jurisdiction Transmitter unit is to be used with a purely resistive antenna when installed in Class I Div 2 areas 205 Keith Valley Road Horsham PA 19044 a Fe H EK U S and Canada 1 800 553 9092 24 Hour Service 1 800 527 6297 DREXELB ROO
13. RAD CON SMA BNC SB SMA M to BNC F with 2 of RG174 cable CN UB 280DC BB bulkhead mount COAXTRAB Arrestor Other types and variations of accessories are available Please contact your local Representative or AMETEK Drexelbrook for more information 15 560 5715 X DRX User s Manual Section 9 Specifications 9 1 5605715 X DRX Specifications General 600 to 1 000 feet 180 to 305 m in plant obstructed 4 5 miles 6 8 km LOS with Omni antenna 20 miles 82 km LOS with Yagi antenna Inputs One 1 4 20mA analog input 16 bit 125 ohms impedance Two 2 digital inputs 5 30VDC Outputs One 1 4 20mA analog input 16 bit short circuit protected Two 2 digital inputs dry contact NO contact rating 250VAC 2 A I O Expansion Capacity Four 4 analog and eight 8 digital I O modules Repeatability Current loop 0 02 Current loop 0 2 of full scale at 77 F 25 C Wiring Connections 12 24 AWG screw type terminals removable terminal blocks DIN rail mount Input Voltage 9 to 30VDC Reverse Polarity Yes Protection Surge Protection Power Consumption 75mA avg 200mA peak 24VDC during transmission plus I O modules Frequency Transmit Power RX Sensitivity Factory configured unique 16 bit coding of each transceiver pair allows multiple units to be used in the same area Antenna Connector MCX female Antenna Impedance Indicators External LEDs power RF link I O status RF
14. al Output Expansion Module Analog Output Expansion Module Analog I O Using 20 Internal Power Total Power Supply Requirement Sum of all devices used 8 max Analog Input 8 max 32 256 Expansion Module KR These currents are 24VDC Er Allow for 200mA peak on the transceiver ie 75mA average 200mA peak KE Ifyou are using internal power for the analog 4 20mA current loops then you willneed toadd20mA for each input and output being used in this fashion 12 Section 5 Section 6 Input Output Status LEDs 5605715 X DRX Power LED Indicates presence of power to the device It is ON when power is present and OFF when there is no power Status LED When flashing rapidly it indicates an internal error or a module type mismatch A module type mismatch occurs when the module address selection for two different modules i e one 1 digital module and one 1 analog module are set to the same address or two 2 pairs of modules are sharing the same address RF LED e Flashes once every two seconds when there is no RF Link Flashes rapidly when signal strength is marginal see RSSI graph below ON steady indicates an exceptionally strong RF Link Most systems will ash occasionally indicating the presence of intermittent interference in the area Digital OFF means that the digital input or output is Open Input Output ON means that the digital input or output is Closed RSSI Troubleshooting
15. by the factory In many applications the equipment is exposed to hazardous materials OSHA mandates that our employees be informed and protected from hazardous materials Material Safety Data Sheets MSDS listing the hazardous material that the system has been exposed to must accompany any return It is your responsibility to fully disclose allchemicals and decontaminate the returned items To obtain a return authorization number RA contact the Service department at 1 800 527 6297 US and Canada or 215 674 1234 Outside North America Please provide the following information Model Number of Returned Equipment Serial Number Original Purchase Order Number Process Material that the equipment has been exposed MSDS for any hazardous materials Billing Address Shipping Address Purchase Order Number for Repairs Please include a purchase order number even if the repair is under warranty If repair is covered under warranty you will not be charged Ship equipment freight prepaid to AMETEK Drexelbrook 205 Keith Valley Road Horsham PA 19044 COD shipments will not be accepted 21 Form 440 0001 001 3 1 2006 TERMS AND CONDITIONS OF SALE GENERAL ALL ORDERS ARE SUBJECT TO THE FOLLOWING TERMS AND CONDITIONS ANY ACCEPTANCE OF ANY OFFER OF BUYER FOR ANY GOODS OR SERVICES IS CONDITIONED UPON THESE TERMS AND CONDITIONS AND SELLER OBJECTS TO ANY ADDITIONAL OR DIFFERENT TERMS
16. e Fault Contact AMETEK DREXELBROOK Configurable Module Address See next page for details Solid State Switch max Digital input channels 4 6 7 and 8 connections not shown Input Output 2 5 4 2867157 DRX Passive Digital Output By releasing the top part of the housing the user may access DIP switches that allow selection between FAULT OFF or MAINTAIN LAST STATE for each of the eight 8 digital outputs of the 2867157 DRX DIP Switch Settings MAINTAIN FAULT OFF LAST STATE DREXELBROOK 2 AMETEK Supressor Power Supply 250VAC 2A max Digital output channels 1 2 3 4 6 7 and 8 connections not shown 560 5715 X DRX User s Manual 2 6 Digital Analog Input Output 2867322 DRX 2 wire 4 20mA Device SE Analog Output 4 20mA External Voltage ven wire Source 4 20mA Device Lee ee PN b S ro mm H I w Na r zm e em e e em e em em wi Floating Power Supply 5 36VAC DC Solid State Switch max Supressor U L Power Supply 250VAC 2A max LAA 10 mem en SE CR 7 8 RAD IN OUT 2D 1A 1 S DREXELBROOK Section 3 Input Output Configuring I O Module Addresses Each pair of I O modules such as the 2867115 DRX and the 2867128 DRX must share a unique module address Once a module address has been assigned to a pair of I O modules that module address may not be used on any other pair of I O modules on the same radio pair Available addresses a
17. ed that Buyer promptly notifies Seller of such claim in writing and further provided that at Seller s expense 1 Buyer gives Seller the sole right to defend or control the defense of the suit or proceeding including settlement and 2 Buyer provides all necessary information and assistance for that defense In the event of a charge of infringement Seller s obligation under the agreement shall be fulfilled if Seller at its option and expense either i settles such claim ii procures for Buyer the right to continue using such goods iii replaces or modifies goods to avoid infringement or iv accepts the return of any infringing goods and refunds their purchase price or iv defends against such claim H Buyer furnishes specifications or designs to Seller the obligations of Seller set forth above shall not apply to goods made by Seller using such specifications or designs and Buyer shall defend indemnify and hold Seller harmless against any third party claims for infringement which arise out of Seller s use of specifications or designs furnished by Buyer SOFTWARE LICENSE If goods purchased hereunder include software Software Buyer may use the Software only as part of the goods Buyer may not use copy or transfer any of the Software except as may be permitted under the applicable License Agreement provided with the goods Buyer s right to use copy or transfer the Software shall terminate upon termination of Buyer s right to
18. es must be paid in United States dollars CREDIT Seller reserves the right at any time to revoke any credit extended to Buyer or otherwise modify terms of payment if Buyer fails to pay for any shipments when due or if in Seller s opinion there is a material adverse change in Buyer s financial condition Seller may at its option cancel any accepted Order if Buyer fails to pay any invoices when due DELIVERY Shipments are F O B place of manufacture Shipping Point and the Buyer shall pay all freight transportation shipping duties fees handling insurance storage demurrage or similar charges from Shipping Point Delivery of goods to common carrier shall constitute delivery and passing of title to the Buyer and all risk of loss or damage in transit shall be borne by Buyer Any claims or losses for damage or destruction after such delivery shall be the responsibility of Buyer Seller reserves the right to make delivery in installments which shall be separately invoiced and paid for when due without regard to subsequent deliveries Delay in delivery of any installment shall not relieve Buyer of its obligation to accept remaining deliveries Acknowledged shipping dates are approximate only and based on prompt receipt of all necessary information from Buyer and Buyer s compliance with terms of payment TAXES All sales excise and similar taxes which Seller may be required to pay or collect with respect to the goods and or services co
19. ission of Seller s invoices thereof LIMITATION OF LIABILITY Seller s liability for any claim of any kind except infringement of intellectual property rights shall not exceed the purchase price of any goods or services which give rise to the claim SELLER SHALL IN NO EVENT BE LIABLE FOR BUYER S MANUFACTURING COSTS LOST PROFITS LOSS OF USE OF THE GOODS OR SERVICES COST OF CAPITAL COST OF SUBSTITUTE GOODS FACILITIES SERVICES OR REPLACEMENT POWER DOWNTIME COSTS CLAIMS OF BUYER S CUSTOMERS FOR DAMAGES OR OTHER SPECIAL PROXIMATE INCIDENTAL INDIRECT EXEMPLARY OR CONSEQUENTIAL DAMAGES Any action against Seller must be brought within eighteen 18 months after the cause of action accrues These disclaimers and limitations of liability shall apply regardless of the form of action whether in contract tort or otherwise and further shall extend to the benefit of Seller s vendors appointed distributors and other authorized resellers as third party beneficiaries PROHIBITION FOR HAZARDOUS USE Goods sold hereunder generally are not intended for application in and shall not be used by Buyer in the construction or operation of a nuclear installation or in connection with the use or handling of nuclear material or for any hazardous activity or critical application where failure of a single component could cause substantial harm to persons or property unless the goods have been specifically approved for such a use or application Seller disclai
20. l be performed in accordance with generally accepted industry practices D Remedies Seller s liability under this section is restricted to replacing repairing or issuing credit at Seller s option for any returned goods and only under the following conditions 1 Seller must be promptly notified in writing as soon as possible after the defects have been noted by the Buyer but not later than 1 year from date of invoice from Seller 2 The defective goods are to be returned to the place of manufacture shipping charges prepaid by the Buyer 3 Seller s inspection shall disclose to its satisfaction that the goods were defective in materials or workmanship at the time of shipment 4 Any warranty service consisting of time travel and expenses related to such services performed other than at Seller s factory shall be at Buyer s expense E Repaired Reconditioned Goods As to out of warranty goods which Seller has repaired or reconditioned Seller warrants for a period of sixty 60 days from date of its invoice only new components replaced in the most recent repair reconditioning F Returns and Adjustments No goods may be returned unless authorized in advance by Seller and then only upon such conditions to which Seller may agree Buyer must obtain an RMA Return Material Authorization number from Seller prior to any return shipment and such RMA number must appear on the shipping label and packing slip Buyer shall be responsible for the retu
21. ms all liability for any loss or damage resulting from such unauthorized use and Buyer shall defend indemnify and hold harmless the Seller against any such liability whether as a result of breach of contract warranty tort regardless of the degree of fault or negligence strict liability or otherwise EXPORT CONTROL Buyer shall comply with all export control laws and regulations of the United States and all sales hereunder are subject to those laws and regulations Seller shall not be named as shipper or exporter of record for any goods sold hereunder unless specifically agreed to in writing by Seller At Seller s request Buyer shall furnish Seller with end use and end user information to determine export license applicability Buyer warrants in accordance with U S Export Law that goods sold hereunder shall not be destined for facilities or activities involving nuclear chemical or biological weapons or related missile delivery systems in named prohibited regions or countries GOVERNING LAW Seller intends to comply with all laws applicable to its performance under any order All matters relating to interpretation and effect of these terms and any authorized changes modifications or amendments thereto shall be governed by the laws of the Commonwealth of Pennsylvania No government contract regulations or clauses shall apply to the goods or services this agreement or act to bind Seller unless specifically agreed to by Seller in writing N
22. re numbers 1 through 8 If module addresses conflict or are improperly set within a connected group an indication will be given by the STATUS LED see section below The 5605715 X DRX Transceivers are designed to operate as groups and are factory programmed Manual address configuration is not required for the transceiver units Module Addresses Selection Switches 5 5 5 4 JL 6 4 JL 8 a 1 8 3 7 H 7 3 7 7 7 7 x i N j 1 N 11 560 5715 X DRX User s Manual Section 4 Power Budget Requirements 5605715 X DRX The following table may be used as a reference when determining your power supply requirements Total power requirements are shown per module per side of the system For example the transmitter side may have one 1 transceiver one 1 2867115 DRX expansion module and one 1 2867144 DRX expansion module The total power requirement for this side of the system would be 213mA 75mA 26mA 32mA 4x 20mA The matching receiver side would have one 1 transceiver one 1 2867128 DRX expansion module and one 1 2867157 DRX expansion module The total power requirement for this side of the system would be 287mA 75mA 100mA 32mA 4 x 20mA Assuming internal bus power is used for analog I O Table 1 5605715 X DRX Rail Builder Power Budget Worksheet Quantity X Power Requirement in mA Total Power Consumption in mA Transceiver 1 Digital Input 208 Expansion Module 100 800 Digit
23. rned goods until such time as Seller receives the same at its plant and for all charges for packing inspection shipping transportation or insurance associated with returned goods In the event that credit for returned goods is granted it shall be at the lesser of the then current prices or the original purchase price Claims for shortage or incorrect material must be made within five 5 days after receipt of shipment ALL OTHER WARRANTIES FOR ANY OF SELLER S GOODS OR SERVICES WHETHER ORAL WRITTEN EXPRESS IMPLIED STATUTORY OR OTHERWISE INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE ARE EXCLUDED AMETEK DREXELBROOK INTELLECTUAL PROPERTY Seller s sale of goods or provision of related documentation or other materials to Buyer shall not transfer any intellectual property rights to Buyer unless Seller specifically agrees to do so in writing Seller shall retain ownership of all applicable patents trademarks copyrights and other intellectual property rights Buyer shall not use copy or transfer any such items in violation of Seller s intellectual property rights or applicable law or for any purposes other than that for which the items were furnished Seller shall defend any lawsuit brought against the Buyer based on a claim that the design or construction of the goods sold hereunder by Seller infringe any United States or Canadian Patent Copyright or Mask Work Registration provid
24. use the goods PACKAGING WEIGHTS AND DIMENSIONS Buyer specified packing or marking may be subject to additional charges not otherwise included in the price of the goods Published weights and dimensions are estimates or approximate only and are not warranted FORCE MAJEURE Seller shall not be responsible for delays in delivery or any failure to deliver due to causes beyond Seller s control including but not limited to the following items acts of God war terrorism mobilization civil commotion riots embargoes domestic or foreign governmental regulations or orders governmental priorities port congestion acts of the Buyer its agents or employees fires floods strikes lockouts and other labor difficulties shortages of or inability to obtain shipping space or transportation inability to secure fuel supplies or power at current prices or on account of shortages thereof or due to limitations imposed by the extent of availability of Seller s normal manufacturing facilities If a delay excused per the above extends for more than ninety 90 days and the parties have not agreed upon a revised basis for continuing providing the goods or services at the end of the delay including adjustment of the price then Buyer upon thirty 30 days prior written notice to Seller may terminate the Order with respect to the unexecuted portion of the goods or services whereupon Buyer shall promptly pay Seller its reasonable termination charges upon subm
25. vered by any Order shall be for the account of the Buyer except as otherwise provided by law or unless specifically stated otherwise by Seller in writing TERMINATION AND HOLD ORDERS No Order may be terminated by Buyer except upon written request by Buyer and approval by Seller and if said request is approved by Seller under the following conditions 1 Buyer agrees to accept delivery of all of the units completed by Seller through the workday on which Seller receives the written termination request 2 Buyer agrees to pay to Seller all direct costs and expenses applicable to the portion of the Order that is incomplete WARRANTY A Hardware Seller warrants its goods against defects in materials and workmanship under normal use and service for one 1 year from the date of invoice B Software and Firmware Unless otherwise specified Seller warrants for a period of one 1 year from date of invoice that standard software or firmware when used with Seller specified hardware shall perform in accordance with Seller s published specifications Seller makes no representation or warranty expressed or implied that the operation of the software or firmware shall be uninterrupted or error free or that functions contained therein shall meet or satisfy the Buyer s intended use or requirements C Services Seller warrants that services including engineering and custom application whether provided on a fixed cost or time and material basis shal
Download Pdf Manuals
Related Search