G-LEC Solaris User Manual
Contents
1. G LEC Solaris User Manual To avoid danger you should read this user manual thoroughly before use of the product This product is for professional use only and not designed for home or residential use G LEC Solaris Product Information Overview Solaris hanging 360 LED video curtain for Events and Installations Dear Customer We thank you for purchasing the Solaris system from G LEC With this product you have an efficient and flexible LED video playback system which has been built using leading edge technology and components Before your product left our facility it was tested to ensure that you receive a product in perfect condition Please ensure that anyone working with the system fully reads and understands this manual before working with the product and follow its instructions especially safety related issues This manual also contains important information in regard to commissioning Be sure that this documentation is forwarded when the product is passed on to third parties These instructions should be read are retained Should you believe that your product was damaged in transit please file a report with the forwarder immediately otherwise any claim for compensation may be void G LEC Vision GmbH may make improvements and or changes to the product s and or the program s in this manual without prior notice The manual could include technical inaccuracies or typographical errors Changes and updates are made to this2. Solatie Bic heed pg a jiya issa a Ch St St et e je e H 2 S E E a J a ii i oP on oe i O O OO Cpe pierre pa fa pe es A O a In order to fully mount a system please do as follows 1 Mount the Solaris Brackets in their desired location 2 It is recommended to place the Solaris PSU and Solaris Manager close to the Brackets in order to minimize cable distances and the potential for problems arising 3 Connect each bracket to the output from the Solaris PSU there are 8 outputs on each PSU The connection is made through a cable with a Neutrik Soeakon connector on each end These connectors are keyed to only connect one way There is no specific sequence in regard to connecting the Solaris Bracket to the output of the PSU but care must be paid to ensure that any maximum load is not exceeded as follow Note that the top 4 outputs have a maximum capacity of 320 Watts and the bottom 4 outputs have a capacity of a further 320 Watts Exceeding these ratings is not permitted In order to help you calculate the load each Solaris sphere has a maximum current draw of 0 5 Watts gute www G LEC com Solarist User Manual V1 0 Tel 49 0 7248 927400 4 The Solarist Manager contains 16 numbered outputs Connect the first output to the first Solaris Bracket in line This will be fed the first pixel information from the mapping in the S Drive II Video Proce
3. Commercial Register of the Local Court of Mannheim hrb 707051 Managing director CEO Udo KUnzler Kasper Gissel f Technology Solaris User Manual V1 0 Tel 49 0 7248 927400 www G LEC com
4. interference in residential areas fechnology Solarist User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Contact and Support Information For more information please visit our website http www g lec com In urgent cases or problems please contact us directly at G LEC Vision Ltd e mail info g lec com Tel 49 7248 927400 G LEC the G LEC name and logo are registered trademarks of G LEC Vision GmbH Karlsbad Germany Various technologies used within these products are patented and patent pending G LEC Vision GmbH works to continuously improve the products and their documentation efforts Therefore the details and operations described within the pages of this manual may vary from time to time We appreciate your understanding G LEC Vision GmbH assumes no liability neither explicitly or implicitly for incidental or for any consequential or indirect damages including profits business interruption loss of business information and the like from the use or inability to use any of the products mentioned in this guide even if G LEC Vision GmbH has been made aware of any possible situation occurring As some may limit or the exclusion of liability for consequential or incidental not allow any damage it may be that the above is not true for you G LEC Vision GmbH Im Stoeckmaedle 15 D 76307 Karlsbad Germany Phone 49 7248 927 40 O Fax 49 927 40 72480 http www g lec com info g lec com registering office
5. regulations should always be used e f permanently installed inspections should be carried out on a regular basis e Dispose of the packaging material after installation e Disconnect all power to the Solaris system before cleaning e The Solaris system is not intended to have objects decorations or other items suspended from it To do so would be unsafe and would void all warranties e Solaris is designed to be suspended directly from a Solaris bracket Through its flexibility Solaris lines can be formed into different shapes Please note however that any additional suspension of the Solaris lines must not be done by the cable between the spheres but by the eyelets located at the first and last sohere on each line This is especially important in situations where the Solaris will be physically moved during its use f rechnology 3 Solarist User Manual V1 0 Tel 49 0 7248 927400 www G LEC com System Components This chapter describes the typical components and the accessories which the Solaris uses in detail For other common system components such as media servers the S Drive II video processor and control software please refer to the relevant user guides Solaris system components overview S Drive Il Video Processor This video processor receives an external DVI D source to be played on a Solaris system It is configured using some free of charge proprietary G LEC software A fibre optic output is sent to the Solaris Ma
6. several times and pull it out to remove any dirt To clean Solaris Spheres and Lines To clean the Solaris lines and spheres you should use a slightly damp cloth No solvents detergents or abrasives should be used or they will damage the spheres and associated wiring Solarist User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Troubleshooting Please read the following FAQ s should you have problems with your system For further contact information please see the Contacts section at the end of this manual Problem The green light in the power switch of my Solarist PSU Manager S Drive II does not light up Possible solutions It is not receiving mains power Check that the power source is on and that connections are firmly made The Neutrik Powercon connector needs to be inserted and turned clockwise to lock into place and make a connection Check the fuses on the units and replace if blown Problem The video signal is playing but the output from each Bracket is backwards Possible solutions The brackets are plugged into the Solaris t Manager in the wrong order Try connecting them in the opposite order if this problem is repeated across all of your brackets Problem The video signal is playing backwards on one of my Brackets Possible solutions Ensure that the Bracket is physically placed in the same orientation as your other brackets A painted arrow on the topside of each bracket can help ensure consiste
7. anti clockwise a quarter turn before attempting to pull the connector apart Sequential Solaris Lines can be connected using the same method 8 Each Solaris Line has a tab at the first and last sphere These are for the specific purpose of attaching a secondary safety wire and must be used at the point where a Solaris Line connects to a Solaris Bracket Further safety cables should be used where systems are placed above people or objects which may be damaged 9 Connect mains power to the Solaris Manager PSU and S Drive II units via their power inputs Turn on all units via their onboard switch 10 Connect a DVI D source to the input of the S Drive Il and configure the S Drive II for your desired layout For further information consult the S Drive Il user manual Once configured your Solaris system will play back the signal being fed and distributed via the S Drive Il Solarist User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Maintenance Cleaning the Fibre Optic Cables and Connectors In order to clean the fibre optic cables or connections on the S Drive II and Solarist Managers you should use a soft cloth or swab To clean fiber optic cables Place the soft cloth on a flat table Carefully remove the optical fiber head by hand Gently move the optical fiber several times on the clean cloth to remove any dirt To clean fiber optic connectors Insert the swab into each optical opening Gently rotate the swab
8. m 9 x 17 x 3 5 inches 19 2U high Solarist PSU 300 x 430 x 88mm 12 x 17 x 3 5 inches 19 2U Solaris Bracket 500 x 50 x 40mm 20 x 2 x 1 5 inches Optical Pixel Pitch 120mm 4 7 inches Pixel 2 x 3 color SMD LED Pixel density 64 pixels m Where pixels are set at 120 x 120mm grid Colors 16 million 24 48bit full color Electrical Power 0 5 Watts Pixel at 100 full bright white Manager Data output for 16 Brackets Solaris PSU Input voltage 110 240V AC 50 60Hz Output power 640 Watts max Solaris Bracket Power 130 Watts max 4 x 8 lines Data output 4 x 8 Lines Video Source DVI D via S Drive II Solarist User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Testing ETL UL Solaris is tested and certified to the following ETL UL amp CSA standards CSA C22 2 9 0 Issue 1996 05 15 Ed 1 Rev 2011 07 27 General Requirements for Luminaires Reaffirmed 2011 UL 8750 Issued 2009 11 18 Ed 1 Rev 2011 11 01 Standard for Safety for Light Emitting Diode LED Equipment for use in Lighting Products UL 2108 Issue 2004 02 27 Ed 1 Rev 2011 04 27 Standard for Safety Low Voltage Lighting Systems CE Solaris is tested to the following standards CE amp EMC Emission EN 550022 2006 A1 2007 Class A EN 61000 3 2 2006 A1 09 A2 09 EN 61000 3 3 2008 Immunity EN55024 1998 A1 2000 A2 2003 Test Report FS 1108 183923 001 Notice This is a Class A digital device and may cause radio
9. manual periodically so to ensure that you have the latest version please check our website at www g lec com Copyright Notice This manual is the intellectual property of G LEC Vision GmbH 2012 No part of this publication may be reproduced or copied in any way and by any means and manner without the express written consent of G LEC Vision GmbH Solarist User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Safety Overview e Read and follow all warnings precautions and instructions Do not block the ventilation areas of any components within the Solaris system Do not install Solaris near any heat sources such as radiators stoves or other similar devices Do not use any component of the system if it is or appears to be damaged or broken e Use only G LEC approved parts peripherals or accessories Contact G LEC Vision or one of their authorized distributors if you have questions in regard to the safe installation operation and maintenance of the Solaris system e The installation of the Solaris system should only be performed by qualified personnel e Care should be taken to avoid damage to any cable within the system Damaged cables should be replaced before use e Do not install Solaris t near combustible or flammable materials e When Solaris is being hung above people please follow your local regulations to ensure compliance of the hanging equipment used e Asecondary safety wire approved to your local
10. nager Solaris Lines Available in various standard lengths Solaris Lines are cables mounted with LED spheres at a pitch of 120mm Lines can be interconnected in different lengths up to a maximum of 64 spheres f Technology Solaris User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Solaris Bracket The Solaris Bracket is where the Solaris Lines plug into Each bracket has a power input from the PSU a data input from the Solaris Manager along with 4 outputs for Solaris Lines It can be mounted by attaching a coupler to the central hole or via the two M10 threaded sockets at the ends of the Bracket Solarist Power Supply Unit PSU The Solaris PSU receives a mains voltage signal and has 8 outputs each of which connects to a Solaris Bracket fecnnolog Solaris User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Solaris Manager The Solaris t Manager receives a fibre optic signal from the S Drive Il and has a fibre optic output to connect further Managers It is powered from a mains voltage input and has 16 CAT 5 outputs which feed signal to the Solaris Brackets G LEC Software Available for free download from www g lec com eCcNNOIOg Solarist User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Solaris System Diagram The Solaris system should be connected as shown in the diagram below System Diagram A Poeti he a ee i Cangur Mailin Server 4 i L
11. ncy easily Solarist User Manual V1 0 Tel 49 0 7248 927400 www G LEC com Item number G933004 G933005 G933006 G933007 G933019 G933012 G944013 G944015 G944004 G944005 G944006 G944042 G944022 G944007 G944008 G955009 G955014 G955010 ett www G LEC com Solaris Product and Accessories List Product Name Description Solaris Line 8 balls on line 96 cm with 12 cm pitch Solarist Manager feeds up to 16 Solaris Brackets Solaris Bracket Output for 4 Solaris Lines Solaris PSU for up to 120 lines Solaris Single One ball on 12 cm line S Drive Il Video processor for Solaris with DVI D input Fiber Optic Cable 20m Fibre Optic Coupler metal CAT 5 Ethernet Cable 2m CAT 5 Ethernet Cable 5m CAT 5 Ethernet Cable 10m Speakon Cable 2 5m Speakon Cable 5m Blank line extension cable 0 96m Blank line extension cable 1 92 m Flight case for Solaris Containers 11 containers per case Containers for Solaris lines 12 Lines per container Transflex flight case for accessories Solaris User Manual V1 0 Tel 49 0 7248 927400 Technical Specifications Weight Solarist Line 960mm 37 8 inches 8 pixels 360 grams 0 8 lbs Weight m 2 9kg m 120mm 4 7 inch pixel pitch gt 8 single lines gt 64 pixels Solarist Manager 4kg 8 8 Ibs Solaris PSU 6kg 13 2 Ibs Solaris Bracket 620g 1 4 Ibs Dimensions Solaris Line length 960mm 37 8 inches Solarist Manager 230 x 430 x 88m
12. ssor This connection is made using a shielded CAT 5 cable Connect output to the second Bracket in line continuing until the maximum of 16 outputs are used If you wish to connect further brackets then a second Solaris Manager will be required 5 Using a compatible fibre optic cable connect the output of the S Drive II to the input of the Solaris t Manager on the right hand side of the unit These connectors are keyed so need to be inserted the correct way around but they simply push in to lock To remove them pull gently on the side of the connector only and it should release The S Drive II will normally sit at your video control position and therefore the use of fibre optic cable allows the fast transmission of data across longer distances 6 Should you need to connect further Solarist Manager boxes they can be daisy chained using further fibre optic cables connecting the output of the first to the input of the next and so on 7 Connect your desired configuration of Solaris Lines to the Solaris Brackets The connection between these two elements is via a keyed 4 pin connector Ensure that both connector components are correctly aligned and push them together The male side of the connector has a locking ring which needs to be turned a quarter turn clockwise until you feel it physically click into place and will not turn further Once clicked a firm connection has been made To undo these connectors turn the locking ring
Download Pdf Manuals
Related Search