GardTec 595 - Capstan Security
Contents
1. Press YES to start setting the system the exit tone will sound and the display will show EXIT Now 123C All Zones ON 30 To turn Area 1 Off press YES 1 and or To turn Area 2 Off press YES 2 and or To turn Area 3 Off press YES 3 and or To turn the Cleaner Area Off press YES 0 As areas are turned off they will be removed from the display Exit the premises or retire to an un protected area as detectors are violated the continuous exit tone will change Areas must first be programmed by the installation company before they will appear on the display Area Setting using Area codes Area codes are only effective to their own area with the exception of the cleaner area This may be turned off by an area code only if all areas are in the unset condition Use is the same as Setting the system shown on page 5 but only the relevant area will be set Page 8 GardTec 595 User Manual Removing Zones Master amp Main codes only If programmed by the installation company individual zones may be removed this may only be done by a Master or Main level of code It should be noted that if an Area Main code is being used only zones associated with that area may be removed 1 With the display showing lt lt lt lt UNSET gt gt gt gt 01 JAN 18 58 01 2 Enter a Master or Main level code the display will show Do you want2. Note Enter the premises via the authorised entry route the broken entry tone will sound proceed to the keypad At the keypad enter a valid code the display will show lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 The system is now unset If an Area Code has been entered only the area associated with that code will be unset If a Cleaner Code has been entered only the cleaner area will be unset In the event of the system being set using ACE when the battery is low the display will show ACE Battery Low when the system is unset Press NO to clear the display and then change the battery in the Keyfob Part Setting The System using Master amp Main type codes 1 Note Note With the display showing ee a gt Enter a Master or Main type code the display will show for example Do you want to Set STUART Press 1 2 or 3 for Part 1 2 or 3 the display will show for example EXIT Now 123C Part 1 15 If a Global code Master or Main has been used all areas that are being set will be Part 1 set If an Area Main code has been used only Part 1 set for that associated area will occur Page 6 GardTec 595 4 The exit tone may or may not be heard dependant on the system settings Exit the premises or retire to an unprotected part of the system At the end of the exit time eithe
3. 1 2 Note Note With the display showing Un Enter a Master or Main type code The display will show SE flashing Press 1 2 or 3 for Part 1 2 or 3 the display will show the E and The two bottom bars if Part 1 has been selected The top and bottom bars if Part 2 has been selected The bottom bar only if Part 3 has been selected If a Global code Master or Main has been used all areas that are being set would be Part Set If an Area Main code has been used only the Part Set associated with that area would be Part Set The exit tone may or may not be heard dependant on the system settings Exit the premises or retire to an unprotected part of the system At the end of the exit time either the exit tone will stop or a single beep will be emitted dependant on system settings Part Setting System using Area 1 2 or 3 codes With the display showing Un Enter an Area code 1 2 or 3 The exit tone will sound and the display will show E Press NO then 1 2 or 3 for Part 1 2 or 3 The bars on the display will change to The two bottom bars if Part 1 has been selected The top and bottom bars if Part 2 has been selected The bottom bar only if Part 3 has been selected The exit tone may or may not be heard dependant on the system settings Exit the premises or retire to an unprotected part of the system At the end of the exit time either the exit tone will stop or a single beep will be emi
4. Press 1 2 or 3 on the receiver keypad for the Part Set you require Unsetting the System with ACE 1 Enter the premises via an authorised entry point 2 Point the keyfob at the receiver and press the button Page 40 GardTec 595 User Manual Programming ACE Keyfobs onto your System Each keyfob will occupy a User number The number of keyfobs that may be used is limited by the maximum number of user codes available on the system up to a maximum of fourteen It is recommended that a keypad entered code is used for the Master User No 1 to allow for the programming of other User functions 1 Follow the procedure for programming user codes to the point when the user code is entered 2 Point the keyfob at the ACE unit and press the button on the fob 3 Repeat this procedure for any other fobs you wish to be programmed using a different user number each time e g User 2 or User 3 etc each time 4 If more than one ACE receiver is fitted fobs need to be programmed onto all ACE receivers retaining the same user number for each individual fob Note When programming the fob onto more than one receiver on the same system the button on the fob MUST be held down continuously between programming onto the first and other ACE receivers Note In all cases when the ACE is used only Master amp Main user levels will allow part setting via the keyfob Other code levels will only allow part setting in conjunction with the keypad
5. If further training is required for new staff etc please contact your Installation Company This user Manual should be accessible by all people who will be using the system If extra copies are required the manual may be downloaded from our web site www gardtec ltd uk Testing Servicing Your System The system you have installed will give many years of service but it should be tested and serviced on a regular basis by a qualified installation engineer It may be a condition of your insurance policy and or your Police response that it is serviced at regular intervals For details on service periods for your system please contact your installation company Page 39 User Manual GardTec 595 ACE User Instructions ACE Advanced Control Equipment allows control of your Gardtec 800 Series system via Infra Red Remote control Ace is available built in to a range of keypads or as a stand alone unit control is via neat remote keyfob s We strongly advise that User Number 1 is not used for ACE in order that the user retains control of the programming functions Era i _ Pa ge Setting the System with ACE 1 Point the keyfob at the ACE receiver and press the button 2 When the exit tone sounds exit the premises in the usual way Part Setting the System with ACE 1 Point the keyfob at the ACE receiver and press the button 2 When you hear the exit tone press the keyfob button again within 3 seconds for Part Set 1 or
6. Keypad 8 Location Z e Q A O O w Q 0 alaala Keyswitch 1 Location Reserved User Code User No Keyswitch 2 Location Reserved User Code User No Keyswitch 3 Location Reserved User Code User No Keyswitch 4 Location Reserved User Code User No Keyswitch 5 Location Reserved User Code User No Keyswitch 6 Location Reserved User Code User No Keyswitch 7 Location Reserved User Code User No Keyswitch 8 Location Reserved User Code User No External Proximity Reader 1 Location External Proximity Reader 2 Location Internal Proximity Reader 1 Location Internal Proximity Reader 2 Location Installation Company Name Installation Company Tel E mail Web Address Other Information Note THIS SECTION MUST BE COMPLETED BY THE INSTALLATION ENGINEER Page 2 GardTec 595 User Manual Introduction The GardTec 595 Control Panel is capable of controlling up to 40 zones with 30 individual Users Control of the system is via Remote Keypads RKPs and two types of display variation are available LCD giving two rows of 16 character English text and LED giving two 7 segment LED digits Control is also possible via Proximity Reader s Some of the more advanced option of the system are only available through the LCD RKP s Please take time to familiarise yourself with the type of equipment fitted to your premises as it will prove invaluable whilst using this manual User Code Types Several types of User Codes are available o
7. Un Enter a Master or Main level code 2 The display will show SE flashing press NO 3 The Display will show F E flashing press YES 4 The display will show r 5 Enter the zone number you wish to remove followed by YES Page 23 User Manual GardTec 595 6 The display will show r 7 If you wish to remove other zones return to step 5 Or To escape press 0 the display will show SE flashing 8 Press YES to start setting the system 9 Exit the premises or retire to an unprotected part of the system At the end of the exit time the exit tone vvill stop provided the system vvas clear Note Zone remove is only effective for the one set Testing The System Master amp Main codes only With the display showing Un Enter a Master or Main level code the display will show SE flashing Press NO twice the display will show t E flashing Press YES the display will show t A press YES if you wish to test all areas or press NO until the area you wish to test is displayed then press YES The display will show tE if all zones are clear Whilst in test mode Pressing 6 will silence the internal sounders Pressing 4 will toggle the strobe On Off Pressing 9 will toggle the Bells On Off When you have finished testing the system press 0 twice to return to the Unset condition Page 24 GardTec 595 User Manual Viewing The Event Log Master code only This function is only
8. Whilst viewing the Log Pressing NO will move back to the previous event Pressing YES will move forward to the next event Pressing 7 will take you to back to the last event of the previous day Pressing 9 will take you forward to the first event of the next day Whilst viewing a zone descriptor pressing 5 will show the zone number 6 When you have finished viewing the Log press 0 twice the display will show Changing The Chime Status Master code only The Chime zones will have previously been programmed by the installation company A Master level code may change the status of the Chime between On and Off To do so proceed as follows 1 With the display showing 2 Enter a Master Code the display will show for example 3 Press NO four times the display will show Page 12 GardTec 595 lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to Set STUART 2 Do you want to Change Chime GardTec 595 User Manual 4 Press YES the display will show for example Chime is Off ok DE Chime is On ok 5 Press NO to change the status of the Chime then press YES the display will show Do you want to Change Chime 6 Press 0 to escape the display wi
9. GardTec 595 Allows Area 2 Setting Area 2 Part Setting Area 2 Zone Remove Area 2 Test Area 2 Unsetting Allows Area 3 Setting Area 3 Part Setting Area 3 Zone Remove Area 3 Test Area 3 Unsetting If programmed by by your installation company will operate the system as normal but will send a PA signal to your central station Refer your installation company for use of this feature Group Code Levels affecting group or groups of areas Group Master Group Main Group Area Allows Setting Part Setting Area Setting Zone Remove System Test Viewing the Log Chime On Off Program User Codes Set Time Date Unsetting Will also allow setting unsetting of individual areas for greater system control Allows Setting Part Setting Area Setting Zone Remove System Test Unsetting Will also allow setting unsetting of individual areas for greater system control Allows group setting unsetting part setting of a selected group of areas Group Area Codes are classed as an Advanced User Function as they allow for greater flexibility on systems that are using multiple areas For details on using Group Area Codes please refer to the section Advanced Setting and Unsetting Using Group Area Codes on page 35 Control Code Levels affecting an output Control Allows an output that has been pre programmed by the installation company to be operated May also have an attribute of Can or Can t Unset Control level codes can never
10. Set a system Page 4 GardTec 595 User Manual Setting The System 1 5 Note Note Note With the display showing lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Enter the User code followed by YES if Master or Main type code has been used The display will show EXIT Now 123C and a continuous exit tone will sound All Zones ON 15 Exit the premises via the authorised exit route the exit tone will change if any detectors are violated during exit Once the premises are secure listen that the exit tone returns to the continuous tone Wait until the exit tone finishes before leaving Setting the system with an area code will set only the area s associated with that code Setting an unset system with a cleaner code will set the full system To Set the system with cleaner on site Press CODE YES YES 0 Setting amp Unsetting the System via a Keyswitch One of two types of keyswitch es may have been fitted to your system Normal To set the system with a normal keyswitch insert the key and turn to the ON position then remove the key To unset insert the key and turn to the OFF position Biased To set the system with a biased keyswitch insert the key and turn it then return the key to the original position and remove To unset repeat this operation Page 5 User Manual GardTec 595 Unsetting The System 1 Note Note
11. to Set STUART 3 Press NO the display will show Do y warf Gs REMOVE Zones 4 Press YES the display will show EnerZona NOZE then YES or NO 5 Enter the zone number you wish to remove followed by YES pressing NO will un remove a zone the display will show Enter Zone No then YES or NO 6 Repeat step 5 until you have removed all the required zones 7 Press 0 to escape the display will show Do you want to Set STUART 8 Press YES the continuous exit tone will sound 9 Exit the premises via the authorised exit route the exit tone will change as detectors are violated When the premises are secure listen that the exit tone returns to the continuous tone Wait until the exit tone finishes before leaving Note Zone remove is only effective for the one set Page 9 User Manual GardTec 595 Testing The System Master amp Main codes only 1 With the display showing lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Enter a Master or Main level code i i pa Do you want to the display will show Ak SART Press NO the display will show Do you want to REMOVE Zones Press NO the display will show Do you want to TEST the System Press YES the display will show Test ALL Areas Press YES to test the full syste
12. Gard lec R ISCO G R O U P GARDTEG 595 Gontrol Panel LCD User Instructions amp LED User Instructions GardTec 595 Contents User Information nana anon nana nan nes eee nese ve reve ve rere ene Using LCD Keypads INITOQUGUOIN 5 ce it sadirosis t bahtes sht then ash ht hades User Code Types ka u mana aaa aaa nne nanes vere venes ve re ene re vere eee Setting The System aaa hana ana venes e eee veres vere vereni Setting Unsetting Via Keyswitch au uuauuaaaa ananas Unsetting The System 0 eeceeseeseeeeeeeeeeeeeneeseeeeeeeeaes Part Setting The System c eccesceeseeeeeeeneeeeeeeneeeaes Quick Part Setting m0 ana ane nee vere ven rere ver zere tereni Area Setting heii SA RL ate dt REMOVING ZONES nana nanen nanen eneve rere n ene ee re vetet er n Testing The System aaa aa aao nana ana nanen never e serre veren Viewing The Event LOg eeeceeeseeereseeeeesneeeeenneeeeaes Changing The Chime Status ccceeeesseeeeteeeneeeees Programming User Codes da hua uu mana nana aaa ne even e ever ve rene Programming Time amp Date eeren User Initiating Remote ACCesS aauuuaaauauuaannanaannnce ever ecen Resetting After An Alarm da auaaanaoaanaa ana nn ene nese ve never eee Using LED Keypads Setting The System aaa nanes venes ve reve rrene re veres eee Unsetting The System 0 eceesesseeeeeeeeeeeeeneeteeeeeeetaes Part Setting The System eecceeecceeseeeeeeeneeeeeeeee
13. O until the Code Type you require is displayed then press YES Display vvill shovv Code Group None ok Note This screen will not appear if User No 1 is being programmed Group Codes are not available for User No 1 Page 32 GardTec 595 User Manual 7 Press NO until the Grp you wish to control is displayed Then Press YES Note If a Code level other than Control has been chosen the selected Output Group will be Activated each time the code is used and the use of the code will be as normal for that level of code If a Code level of Control has been selected the Output Group will be Activated each time the code is entered or G Tag presented and is normally used in conjunction with a Magnetic Lock for limited Door Entry capability and may be given an extra attribute of Can or Can t Unset A Control Level of Code can never Set the system 8 If you have chosen a Control level of code the display will show s i 1 Cod If you are using another level of code and this ot cay screen is not displayed go to step 11 Or Control Code Can Unset ok 9 Press NO until the required setting is displayed then Press YES If Can Unset was chosen the display will show Qe s Area s If Can t Unset was chosen go to step 11 10 Use the keys 1 2 3 or 0 for C Cleaner to toggle the Area s you wish to control with this code When finished Press YES Display wi
14. Page 41 User Manual GardTec 595 Service Record Date Comments Signature Alarm Reset Type Tamper Reset Type Service Company Page 42 GardTec 595 User Manual User Chart Please use this chart to indicate what user names have been programmed onto your system and those that are in use Page 43 GardTec Ltd Commerce House Whitbrook Way StakeHill Distribution Park Middleton Manchester M24 2SS United Kingdom Internet http www gardtec Itd uk e mail sales gardtec Itd uk 3 MI ie BSIA THE BRITISH SECURITY INDUSTRY ASSOCIATION INVESTOR IN PEOPLE PR5524 Rev1 0
15. ange to Do you want to Prog USER CODES 13 If you wish to program other User Codes return to step 4 Or Press 0 to return to lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Page 16 GardTec 595 Programming Time amp Date 1 With the display showing 2 Enter a Master Code the display will show 3 Press NO six times the display will show 4 Press YES the display will show 5 Press YES for Auto Adjust for British Summer Time the display will show 6 Press NO to change display will show 7 Enter the last two digits of the Year then press YES Display will show 8 Press YES Display will show 9 Enter the Date in the form ddimm follovved by YES Display vvill shovv 10 Enter the Time using the 24Hr Clock format then YES Display vvill shovv 11 Press 0 to return to Unset Page 17 User Manual lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to Set STUART 2 Do you want to Set DATE TIME Summer Adjust is On ok Year is 2004 ok Enter Year 20 Then YES Year is 2005 ok Enter Day Month Then YES Enter Hrs Mins Then YES Do you want to Set Date Time User Manual User Initi
16. ariants with the reader built into the display area of an LCD RKP as an Internal Standalone Reader or as an External Standalone Reader When using G Tag the system may be Set Unset by presenting a valid Tag to one of the Readers Each Tag is programmed onto the system as an individual User Code therefore giving indication via the system Log of who has set and unset the system As the Tags are a close proximity device the risk of code capture is eliminated When programming the G Tags follow the normal Programming Codes instructions to the point when you are asked for the Code for example Now Enter Code Then YES At this point present your G Tag to the reader and the code will be entered If you have more than one reader on your system the G Tag MUST be programmed onto each of the readers on the same User Number Because of this it is essential that you use good housekeeping for the G Tags Mark each of the G Tags and record what User Number the G Tag has been allocated to The readers will be allocated to a specific keypad The G Tag information is stored in the keypad therefore a single keypad having two readers would only require the G Tag to be programmed into one of its readers For multiple keypads with readers the sequence for programming the G Tags would be 1 Enter User Programming Mode 2 Choose what User Number you are using in this case User 2 for G Tag A 3 Program G Tag A onto the f
17. ating Remote Access Optional GardTec 595 Access Remote allows your installation company to examine your system and re program system settings as you need the changes without the need for an engineer to visit your premises If your system has remote communications fitted your installation company may have programmed the system so that you initialise the Access Remote call usually on lines with incoming calls barred To initiate the Remote Call follow the instructions below 1 Note Negotiate with your installation company when you should initiate the Remote Call With the display showing Enter a Master Code the display will show Press NO seven times the display will show Press YES the display will show Until Dialling commences Then Until Connection Then When your installation company has finished the display will show In the event of any errors the display will show Page 18 lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to Set STUART 2 Do you want to Access Remote Please WAIT Please WAIT Dialling Please WAIT Connect lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 l ERROR Try Again GardTec 595 Resetting After an Alarm User Manual Your installation company will ha
18. available via an LCD RKP Page 25 User Manual GardTec 595 Changing The Chime Status Master code only The Chime zones will have previously been programmed by your installation company A Master level code may change the status of the chime between On and Off To do so proceed as follows 1 With the display showing Un enter a Master code 2 The display will show SE flashing 3 Press NO four times the display will show Ch 4 Press YES the display will show oF or on 5 Press NO to change the Chime status 6 When you have finished press 0 twice to return to the Unset condition Programming User Codes Master code only This function is only available via an LCD RKP Page 26 GardTec 595 User Manual Programming Date amp Time This function is only available via an LCD RKP User Initiating Remote Access Users should only initiate Remote Access when instructed to do so by the installation company 1 With the display showing Un enter a master level code then press NO seven times the display will flash Ar 2 Press YES the display will show W Wait then di Dialling then Cn Connected 3 When the installation company has finished the display will return to Un In the event of an error the display will show Er you should try again Page 27 User Manual GardTec 595 Resetting After An Alarm Your installation company will have pr
19. dicated to using LED keypads Twin Seven Segment Note Some functions will not be available when using LED RKP s Setting The System 1 With the display showing Un 2 Enter the User Code followed by YES if Master or Main type code has been used 3 The display will show E and the exit tone will sound Exit the premises via the authorised exit route the exit tone will change if any detectors are violated during exit 4 Once the premises are secure listen that the exit tone returns to the continuous tone 5 Wait until the exit tone finishes before leaving Note Setting the system with an area code will set only the area associated with that code Note Setting an unset system with a cleaner code will set the full system Unsetting The System 1 Enter the premises via the authorised entry route the broken entry tone will sound 2 Proceed to the keypad enter a valid user code the display will show Un 3 The system is now Unset Note If an area code has been entered only the area associated with that code will be Unset Note If a cleaner code has been entered only the cleaner area will be Unset Note In the event of the system being set using ACE when the battery is low the display will show Ab when the system is unset Press NO to clear the display and then change the battery in the Keyfob Page 21 User Manual GardTec 595 Part Setting The System using Master amp Main type codes
20. e Unsetting Will also allow setting unsetting of individual areas for greater system control Group Main Allows Setting Part Setting Area Setting Zone Remove System Test Unsetting Will also allow setting unsetting of individual areas for greater system control Group Area Allows group setting unsetting part setting of a selected group of areas Note Is not able to Set Unset individual Areas Group Area Codes are classed as an Advanced User Function as they allow for greater flexibility on systems that are using multiple areas An example of this may be when a system has Area 1 already Set a user with a Group Area Master or Main Code may enter his her code and change the active areas This removes the need for an Area Level user to remember more than one Area Code or for a Global Master user to unset an entire system in order to set an extra Area In this section we give examples of typical applications for Group Area Codes Your installation company will give you further information on the scenarios when Group Area Codes may be used on your system Setting Using Group Area Code Follow the instructions as for normal setting When you are using a Group Area Code only the Area s allocated to that code will be set Page 35 User Manual GardTec 595 Setting Using Group Master amp Group Main Codes Group Master amp Group Main codes follow global Master amp Main codes with respect to the level functionality The diff
21. e enter six Zeros followed by YES Or Present your G Tag to the Reader The display will show Code Type Master ok 2 Page 14 GardTec 595 6 7 8 9 Press NO until the Code Type you require is displayed then press YES Display will show Code Groups are only used in conjunction with controlling outputs This is dealt with in the Advanced Code Programming section page 32 of this manual Press YES to accept None Display will show for example If you wish to accept the User Name shown press YES and jump to step 12 Or If you wish to change the User Name shown press NO the display will show You may now enter up to nine characters for the user name using the layout shown below for the allocation of characters STU VWX YZ 0 9 Page 15 User Manual Code Group None ok User Name STUART User 1 Name gt User Manual GardTec 595 10 Referring to the character map enter the required character pressing the 3 key will display G pressing it again will show H and again will show I once the correct character is displayed press YES and the display will move on to the next position 11 Continue entering characters up to 9 If you require a blank space press YES while the is displayed 12 As you press YES for the ninth character or if you have jumped from step 8 the display will ch
22. erence lies in the ability to have individual control of the Areas that been allocated to the code 1 With the display showing Enter a Group Master or a Group Main Code Display will show Press YES Display will show If you Press YES the system will start to Set all lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to SET the System Set ALL Areas the Areas that have been allocated to this Code Or If you Press NO the display will show Set The Areas shown will differ dependant on what Off 123 Ok Areas have been allocated to your Code The Top line shows the Areas that are Set and the Bottom line shows the Areas that are Off Unset Use the 1 2 3 amp 0 0 for cleaner Area to toggle the Areas between the Top amp Bottom line When you have finished the display may show for example Set 1 3 Off 2 Ok In this example Areas 1 amp 3 will be Set but Area 2 will remain Off Unset Press YES The system will start to Set the selected Areas Leave the premises via an authorised exit route Page 36 GardTec 595 User Manual Unsetting Using Group Area Code Follow the instructions as for normal Unsetting When you are using a Group Area Code only the Area s allocated to that code will be Unset Unsetting Using Group Master amp Group Main Cod
23. es 1 With the display showing for example SET1 3 Areas 1 amp 3 is Set oi JAN 18 58 01 2 Enter a Group Master or Group Main level Code Display will show lt lt SET1 3 gt gt Set Area s 3 Press NO Display will show for example Unet ALL ArEAS 4 If you wish to Unset all the Areas Press YES The system will Unset all Areas Or If you wish to Unset just 1 of the Set Areas Press NO Display will show for example Set 1 3 Areas 18 3 are Set Off Ok 5 Press the key corresponding to the Area you wish to Unset in this example press 3 The display will show Set 1 Off 3 Ok 6 Press Yes when you are happy with your selection Display will now show lt lt SETI gt gt 01 JAN 18 58 01 Area 3 has now been Unset Page 37 User Manual GardTec 595 Adding Areas to a System with Area s Already Set Group Master amp Group Main Codes If your system already has an Area or Areas already Set you may add more Area s as required 1 With the display showing for example GET Areas 1 is Set 01 JAN 18 58 01 2 Enter a Group Master or Group Main level Code Display will show lt lt SETI SN Set Area s 2 3 Press YES Display will show Set ALL Area 4 If you Press YES all the remaining Areas allocated t
24. irst reader 4 At the next Keypad re enter User Programming Mode 5 Choose the same User Number 2 6 Program the same G Tag A onto the second reader 7 Keep repeating until your G Tag A is programmed onto all readers 8 Now move on to G Tag B on User Number 3 Remember to mark your G Tags Page 31 User Manual GardTec 595 Advanced Code Programming Master Group Master Code LCD Only Codes may be programmed to control Outputs and or Set Unset the system The Outputs that may be controlled will have been pre programmed by your installation company and may not be changed by the user a Master user however does have the ability to allocate the codes not User No 1 to these Group Outputs 7 E p lt lt lt lt UN SET gt gt gt gt 1 With the display showing 01 JAN 18 58 01 2 Enter a Master Code the display may show Do you want to Set STUART 2 3 Press NO five times the display vvill shovv Do you want to Prog USER CODES 4 Press YES the display will show Enter User No 1 31 Then YES 5 Enter the user number 1 to 31 that you wish to program followed by YES the display will show Now Enter Code Then YES 6 Either Enter the User Code you require followed by YES Or Present your G Tag to the Reader The display will show Code Type Master ok 2 6 Press N
25. ll show User 02 Name User 02 11 If you wish to accept the User Name shown press YES and jump to step 16 Or If you wish to change the User Name shown press NO the display will show User 1 Name gt Page 33 User Manual 12 13 14 15 16 You may now enter up to nine characters for the user name using the layout shown below for the allocation of characters STU VWX YZ 0 9 Referring to the character map enter the required character pressing the 3 key will display G pressing it again will show H and again will show I once the correct character is displayed press YES and the display will move on to the next position Continue entering characters up to 9 If you require a blank space press YES while the is displayed As you press YES for the ninth character or if you have jumped from step 8 the display will change to If you wish to program other User Codes return to step 4 Or Press 0 to return to Page 34 GardTec 595 Do you want to Prog USER CODES lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 GardTec 595 User Manual Advanced Setting and Unsetting Using Group Area Codes There are three levels of Group Area Codes Group Master Allows Setting Part Setting Area Setting Zone Remove System Test Viewing the Log Chime On Off Program User Codes Set Time Dat
26. ll show lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Page 13 User Manual GardTec 595 Programming amp Deleting User Codes Master code only The charts on pages 2 amp 34 should be completed by the engineer user for future reference of what codes have been allocated on your system Under no circumstances should the actual user code be written down If your installation company has given you keyswitches for the operation of your system the last five user codes may have been reserved for use by these keyswitches If your engineer has indicated see pages 2 amp 36 that some of the user numbers on your system have been reserved you should not use them whilst programming user codes If you do so your system may be adversely affected 1 With the display showing lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 2 Enter a Master Code the display may show Do you want to Set STUART 3 Press NO five times the display will show Do you want to Prog USER CODES 4 Press YES the display will show Enter User No 1 31 Then YES 5 Enter the user number 1 to 31 that you wish to program followed by YES the display will show Now Enter Code Then YES 6 Either Enter the User Code you require followed by YES If you wish to Delete a Cod
27. m or NO until the area you wish to test is shown Press YES the display will show 1 Status 4 Strobe for 3 seconds 6 Sounder 9 Bell Then for example lt All Zones OK gt TESTING Pressing 1 will enter zone Status mode All zones will show on the display and will be deleted as each zone is triggered Press 0 to escape Pressing 6 will silence the internal sounder Pressing 4 will toggle the Strobe On Off Pressing 9 will toggle the Bell On Off Page 10 GardTec 595 9 10 Whilst in Test mode any zones violated will sound the internal sounder if it has not been silenced and show on the display When you have finished testing the system press 0 twice the display will show Viewing The Event Log Master code only 1 With the display showing Enter a Master Code the display will show for example Press NO three times the display will show Press YES the display will show for 3 seconds Then for example Page 11 User Manual lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to Set STUART Do you want to View the LOG While Viewing 1 Printer On Off Read Log 01 JAN 18 58 01 User Manual 5 This is the most recent event in the log
28. n the Gardtec 595 and each type allows for different levels of access In total 31 User codes may be programmed by a Master Level User Code User number 1 will always be a Master Level User but the remaining 30 User Codes may be programmed to the required level of access The Code Levels should be viewed as four groups Global codes that give system control Area codes that give area control Group codes giving control of more than 1 area and Control codes giving control off outputs The User Code levels available and the functions available for the levels are Global Code Levels affecting full system Set Only Only Allows for the setting of the system Main Allows Setting Part Setting Area Setting Zone Remove System Test Unsetting Master Allows Setting Part Setting Area Setting Zone Remove System Test Viewing the Log Chime On Off Program User Codes Set Time Date Unsetting Area Code Levels affecting areas only Area 1 Allows Area 1 Setting Area 1 Part Setting Area 1 Unsetting Cleaner Full System Setting from unset system Cleaner Area Unsetting from set system Cleaner Part Set from part cleaner set system Area 2 Allows Area 2 Setting Area 2 Part Setting Area 2 Unsetting Area 3 Allows Area 3 Setting Area 3 Part Setting Area 3 Unsetting Main 1 Allows Area 1 Setting Area 1 Part Setting Area 1 Zone Remove Area 1 Test Area 1 Unsetting Page 3 User Manual Main 2 Main 3 Duress
29. o Code will be Set Or If you Press NO Display will show Set Off 23 Ok 5 In this example use the 2 or 3 key to add Area s 2 or 3 to the system Set 6 When you are happy with your selection Press YES The Exit sounder will sound then lt lt SET13 Display will show for example 01 JAN 18 58 01 In this example Area 3 has been added to the Set Page 38 GardTec 595 User Manual Display Blanking Dependant on the level of your system and the legislation that it is required to comply with your installation company may have initialised Display Blanking When this is used the Status of the system will only be indicated on the display for ten seconds after it has been Set and for ten seconds after it has been Unset The Status of the system may be shown by following the procedure below Please note Control Codes or Group codes cannot be used for this feature 1 When the system has just been Set the display will show for example Keseti gt gt 01 JAN 18 58 01 For ten seconds 2 The display will then show for example 01 JAN 18 58 01 3 To show the Status of the system Press YES The display will show for example Press CODE Show Status 4 Enter a valid Code to display the Status for a further ten seconds End User Training Itis the responsibility of your Installation Company to provide adequate training for people who will be expected to use the system
30. ogrammed the reset modes for your system so that it complies to your insurance company and legislation requirements Your installation company will have informed you as to the type of reset that your system is set for If the system is programmed for any code reset enter a user followed by YES if Master or Main code is used the exit tone will sound and the display will show for example E Enter the code again to abort the setting The system is now reset Or If the display shows Er when you attempt to reset it refer to the programmed reset mode and take the appropriate action as follows Reset Type Action Master Code Use a Master code to set and abort setting Engineer Code Call the installation company Engineer Anti Code Call the installation company Anti Code When you try to set the system make a note of the four digit number given on the display call the installation company or central station for an Anti Code and proceed as shown from step 4 To reset the system with an Anti Code enter the number given by the central station or installation company into the keypad this may contain the YES amp NO keys The system is now reset Page 28 GardTec 595 LED Display Glossary Displays During Normal Use Fb e Cb e bb E1 PL Pc e t4 System Unset The system is full setting The system is fully set The system is part 1 setting The system is part 1 set The system is pa
31. r the exit sounder will stop or a single beep will be emitted dependant on system settings Part Setting System using Area 1 2 or 3 codes 1 With the display showing Enter an Area Code 1 2 or 3 the exit tone will sound and the display will show for example Press NO then 1 2 or 3 for the Part Set you require the display will show for example The exit sounders may or may not go silent this will depend on the system settings Exit the premises or retire to an unprotected part of the system At the end of the exit time either the exit sounder will stop or a single beep will be emitted dependant on system settings Quick Part Setting System User Manual lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 EXIT Now 1 All Zones ON 15 EXIT Now 1 Part 1 20 If required there is a quick method to Part Set the system regardless of the level of code being used except Control Level To Part 1 Set the system Enter YES YES CODE The system will now start to Part 1 Set Page 7 User Manual GardTec 595 Area Setting using Master or global Main codes Areas will need to have been set up by the installation company 1 Note With the display showing ee eeUMSETS ES 01 JAN 18 58 01 Enter a Master or global Main code the display will show for example Do you wantto Set ELIZABETH
32. rt 2 setting The system is part 2 set The system is part 3 setting The system is part 3 set The system is cleaner setting The system is cleaner set An alarm has occurred press NO to view Fuse blown or battery volts low Control box tamper bell box tamper Expander1 tamper may show 1 to 4 Telephone Line fault or coms fail Power Cut Tamper keypad 4 may show 1 to 4 TE 4E Ch Uc dt Lo Page 29 User Manual Reset is required by a higher level code or an error has occurred vvhilst programming Reset by Anti Code is required flashing Do you vvant to Set Remove zones Test system Change Chime Program User codes Program date time Log VVaiting for numeric input Wait system in use Engineer code reset required flashing Call Engineer Itis not possible for an LED RKP to display all errors on a system please refer to your LCD RKP User Manual GardTec 595 System Attributes one Type Descriptor Areas 1 2 3 Part Set 1 2 3 one No Example pa Se SF i Er i eee po ji Pes E po e e e EEE ee Seas ee e ae Oooo S S E Oooo S S E po j se es ee po ay e a es ees po SS S E Oooo S S E E E ee s SS Oooo e E F es E E es ee ee ae po po po a S S E Oooo S S E Oooo S S E i ee ee po E LESSEE E Page 30 i GardTec 595 GARDTEC 800 Series System G Tag G Tag Readers are available in three v
33. tees Area Sellin Gj ernia aa RE aai REMOVING ZONES au haaaaaaa nana aa arena vonesave rere veres e vere ve rere Testing The System aa uu h ha aauh ana aan ananas venave reve rere Changing The Chime StatuS au auaaoaaa mana aaa ananas venien eee User Initiating Remote ACCESS Resetting After An Alarm da aauaanoaanana nane eee nese ve never rere ee LED Display C SS LA System Attibutes nana nana aeenee eee eee eee eee eee rere rere eea System G Fagu cis fene nude ditt dyte ret tee Advanced Code Prog ram MIN Qa 00 o hana nan nanen enen Advanced Setting Unsetting Using Group Area Codes Adding Areas to an Already Set System Display Blanking cceeeesceeeeseeeeeseeeeeeeeeeeneeeeeneeeeees End User Training ccsccccesecereseeceseeeeeeeseeeneeseeeeees Te StiING ServiCing eeceeeeceeteeeeeeeeneeteeeeeaeeeeeeeeaeeeeeees ACE Instructions aaa nana nanes enen ee zier eter eee eee ere zeme Programming ACE Keyfobs onto your System Service Record c cccccecceeeeseceeeeeeeeeeeeeeesneeessneeesseeees ST User Manual ONDOD N ND Ww 1 1 N O Oo 11 12 12 13 14 16 17 18 19 20 21 21 21 22 23 23 24 24 26 27 28 29 30 31 32 34 35 38 38 39 39 39 40 41 42 43 User Manual GardTec 595 User Information System Information Keypad 1 Location Keypad 2 Location Keypad 4 Location Keypad 5 Location Keypad 6 Location Keypad 7 Location
34. tted dependant on system settings Page 22 GardTec 595 User Manual Quick Part Setting System If required there is a quick method to Part Set the system regardless of the level of code being used except Control Level To Part 1 Set the system Enter YES YES CODE The system will now start to Part 1 Set Area Setting using Master or Global Main codes 1 With the display showing Un Enter a Master or global Main code 2 The display will show SE flashing Press YES to start setting the system the exit tone will sound 3 To turn Area 1 Off press YES 1 and or To turn Area 2 Off press YES 2 and or To turn Area 3 Off press YES 3 and or To turn the Cleaner Area Off press YES 0 4 Exit the premises or retire to an unprotected part of the system At the end of the exit time the exit tone will stop provided the system was clear Note Areas must first be programmed by the installation company Area Setting using Area codes Area codes are only effective to their own area with the exception of the cleaner area which may be turned off by an area code only if all areas are in the unset condition Removing Zones Master amp Main codes only If programmed by the installation company individual zones may be removed this may only be done by a Master or Main level of code It should be noted that if an Area Main code is being used only zones associated with that area may be removed 1 With the display showing
35. ve programmed the reset modes for your system so that it complies to your insurance company and legislation requirements Your installation company will have informed you as to the type of reset that your system is set for 1 If the system is programmed for any code reset enter a user followed by YES if Master or Main code is used the exit tone will sound and the display will show for example 2 Enter the code again to abort the setting 3 The system is now reset Or If a higher level of code is required one of the following displays will be shown Use a Master code to reset the system Or Call the installation company Or Call the installation company and quote the number given Or Page 19 EXIT Now 123C All Zones ON 15 Can t Set Use Master Code Can t Set Use ENGNR Code Can t Set Use ENG Anti Code 1234 Can t Set Use Anti Code 1234 User Manual GardTec 595 4 To reset the system with an anti Code contact the central station or engineer as instructed by the installation company and quote the source given by the display The central station or engineer will give a return Anti Code this may contain the YES amp NO keys for example 5 YES 2 4 Enter this Anti Code into the keypad The system is now reset Page 20 GardTec 595 User Manual Using LED Keypads This section is de
Download Pdf Manuals
Related Search