Home

FP12 User Guide

1. 6581533 MP3 Circuit Access Cover without belt clip Shure 328678 ai Transistor Silicon NPN Motorola 2N5210 Shure RKC89 02 Transistor Silicon PNP Motorola 2NS088 Shure 864348 R24 Potentiometer 200k Level None st Switch SPST part of R24 a s2 Switch Slide DPDT Hi Z Lo Z None s3 Switch Side DPDT Mic Line Shure 5548020 n Transformer Input None 7 Transformer Output None ur Integrated Circuit Dual Operational Amplifier Raytheon RC4559NB Shure 86811 va Integrated Circuit Audio Power Amplifier Natana LU ure Parts isted as None should be ordered tam Shue Brothere inc Ing product model number relerence designation and part destin Suppe in miles ot tur oniy
2. Hz 1 3 dB Equivalent Input Noise 118 dBV maximum gain source resistance 150 ohms 300 Hz to 20 kHz Copy 185 ue Brothers Ic mare cm Voltage Gain ref 1 kHz Headphone Input _ impedance Impedance Gain Me Loz 4 ohms total 8 ohms 7048 Une per earphone paralel 3p ap Me pez 1k total 2k per ear 9608 Une phone driver parle 55 ap Total Harmonic Distortion Less than 1 40 Hz to 15 KHz measured at 10 dB below clipping point Input Clipping Levels at 1 kHz Mic Input 200 mV 14 dBV Line Input 60V 35 dBV Output Clipping Levels Lo Z 750 mV 2 5 dBV load resistance 4 ohms total 8 ohms per earphone driver parallel Hi Z 15V 23 dBV load resistance 1 k total 2k per earphone driver parallel Input Impedance ref 1 kHz ic 7 5 kilohms 10 Line 66 kilohms 10 Output Impedance re 1 kHz Lo Z 16 ohms 10 Hi Z 440 ohms 10 Phase Input in phase with output Pin 2 of Mic Input in phase win Phones both phone jacks and mini jacks tip and ring Protection Protected against damage from shorted outputs up to SV 14 dBV input signals Power Type 9V alkaline battery Battery Life Approximately 10 hours under normal operating conditions Current Drain typical 6 mAde idle 72 made clipping Temperature Range Operating 0 to 49 C 32 10120 F Storage 29 to 74 C 20 to 165 F Connectors Input Output
3. Locking 3 socket XLR Locking pin XLR phone jacks 2 JI2NHS Y3I4IIdWYV ONIDOIYA SNOHdGVSH Zidd 130OW VIVO IVIINHO3L Headphones Output Phone jack 2 Mini Jack 2 Battery Test Insulated tip jacks red positive and black negative Case Die cast zinc matte black enamel Overall Dimensions 80 9 mm x 150 mm x 55 5 mm 3 3 16 x5 11 16 x2 9 16 in Net Weight 501 grams 1 lb 2 1 2 oz CONTROLS CONNECTORS INDICATOR Level Control applies power to FP12 circultry and sets headphone output level Knob position also in dicates when power is applied Mic Line Switch selects microphone or line level sig nal source HI Z Lo Z Switch selects operation with high impedance greater than 600 ohms or low impedance less than 600 ohms headphones InOut XLR and Phone Jacks provide loop through in ut and output connections for balanced microphone or Ine ievel signal sources Phones A B Jacks provide for connection to high or low impedance headphones Note that A and B head phone jacks can be used simultaneously Each output can accept a headphone phone plug or mini plug Batt Test Jacks can be used to check condition of 9V battery OPERATION lacement Use a coln or screwdriver tuming one quarter turn in either direction to open the battery compartment door Insert a fresh 9V alkaline battery NEDA 1604A Duracell MN1604 Eveready 522 or equivalent in the compart ment Note that the battery contacts ar
4. SHURE THE SOUND OF THE PROFESSIONALS 222 HARTREY AVE EVANSTON IL 60202 3696 U S A AREA CODE 312 866 2200 CABLE SHUREMICRO PROFESSIONAL PRODUCTS GENERAL The FP12 is an inline battery powered amplifier designed to accept a microphone or line level signal bridge it and produce a signal sufficient to drive head phones at very loud levels The FP12 is ideal for anyone in the broadcasting sound reinforcement or audio re cording fields who has a need for headphone moni toring or checking microphone or Ine level cable runs In addition the FP12 can be used to provide multiple headphone feeds a two station intercom extra power for existing headphone circuits or a means of practic ing electronic instruments through headphones FEATURES Wide range frequency response Low input noise and harmonic distortion High impedance bridging input does not load signal source Switchable microphone and line level inputs Switchable low and high impedance headphone out puts Parallel 3 circuit phone and miniature 3 5 mm head phone jacks Balanced loop through locking XLR connectors and phone jacks Powered by easily obtainable 9V alkaline battery Low current drain for extended battery life Rugged construction with durable belt clip for field use Low susceptibility to radio frequency interference SPECIFICATIONS Frequency Response rei 1 kHz 40 Hz to 15 k
5. e polarized and the battery cannot be inserted improperly The compart ment door can be closed by pressing shut with the fastener properly aligned Connections Connect the signal source microphone or line level to the appropriate In Out connector XLR or phone jack and set the Mic Line switch Connect the parallel signal vOut connector XLR or phone jack to the input of mixer tape recorder or amplifier Connect the head phones one or two units to the Phones A B jacks and set the Hi Z Lo Z switch to the proper position for or low impedance headphones Operation Position the FP12 for operation Note that the belt clip can be used to secure the unit to a belt trousertops or D rings on other equipment The belt clip can easily be removed if desired Rotate the Level control from the Off position to the desired listening level Note that the exposed color dot on the Level control knob serves as a reminder that the unit is on Battery voltage can be checked at any time without removing the battery or tuming the unit on Inserting voltmeter leads in the Batt Test jacks observe proper polarity will indicate battery condition GUARANTEE This Shure product is guaranteed in normal use to be free from electrical and mechanical defects for a period of one year from date of purchase Please retain proof of purchase date This guarantee includes all parts and labor This guarantee is in lieu of any and all other guarantees or warra
6. nties express or implied and there Shall be no recovery for any consequential or incidental damages SHIPPING INSTRUCTIONS Carefully repack the unit have it insured and return it prepaid to Shure Brothers Incorporated Attention Service Department 222 Hartrey Avenue Evanston Ilinois 60202 3696 If outside the United States return the unit to your dealer or Authorized Shure Service Center for repair The unit will be returned to you prepaid REPLACEMENT PARTS LIST REFERENCE SHURE PART NO OR DESIGNATION DESCRIPTION COMMERCIAL ALTERNATE en Battery Alkaline 9V Duracell MN1604 cio Capacitor Electrolytic 4 7 pF 25V Nichicon UKB1E4R7KAA c12 C17 Capacitor Electrolytic 10 aF 16V CDE PC10 25 C14 c16 Capacitor Electrolytic 0 47 F 50V None c19 Capacitor Electrolytic 1000 F 16V Mallory 1000816 20 Capacitor Electrolytic 2200 pF 16V Nichicon 1C222MRA c22 Capacitor Electrolytic 220 pF 10V Nichicon 1A221 MAA J132 Phone Jack Stereo Switching Radio Shack 274 282 33 35 Phone Jack Stereo Switching None 4 J6 Miniature Phone Jack Stereo Switching 3 5 mm None ar Terminal Battery Test Red Alco TBA 2 Je Terminal Battery Test Black Ako TBA 0 so Connector 3 Socket XLR In Cannon XLR 3 31 77 Shure 9548060 no Connector 3 Pin XLR Out Cannon XLR332F77 Shure 9548061 Lis Ferrite Bead Ring Stackpole 57 0181 Shure 804250 NP Belt Clip without screws Shure Mp2 Control Knob Level Shure

FP12 User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents